Hydraulic press

WMW-ZEULENRODA PYE 250 S 1 M

Condition: ready for operation (used), Nominal force: 2500kN, operating pressure: 20MPa, ram speed down/up: 210/110mm/s, ram stroke: 500mm, throat depth: 360mm, max. distance between table and ram: 800mm, rated current: 41A, control voltage: 60V, rated voltage: 380V, connected load: 20.5kW, weight: 8t. An on-site inspection is possible. Nsdpfx Asxcx Aaeamodd

Condition: good (used), Year of construction: 1998, Press Force 315.00 t Stroke 500 mm Throat 425 mm Installation Height (Upward Stroke) 1,000 mm Table Surface 1,200 x 815 mm Table Height above Floor 800 mm Ram Surface 1,100 x 700 mm Speed Down 48 mm/s Speed Up 330 mm/s Working Speed 19 mm/s Oil Volume 1,600 l Power Requirement 82.0 kW Weight 23.00 t Dimensions (WxDxH) 2.4 x 2.8 x 4.0 m For Permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation permitted for manual loading according to the CE standard with oil-hydraulic drive, controllable depending on pressure/time and travel, light-guard at the front (Sick), two-hand operation Ndsdpfev Rwu Uox Aamed

Condition: used, nominal force 100 t stroke 320 mm no. of strokes 35 /min distance between columns 360 / 250 mm Distance table/ram, max. stroke up, adjustment up 500 mm table surface area 320 x 450 mm table height over floor 660 mm ram surface 250 x 280 mm spindle diameter 125 mm Ndodpfx Aajvuk N Tsmed power capacity 3,0 kW weight 4,5 t Dimensions (WxDxH) 2,0 x 1,6 x 3,1 m only permitted for hot forming work high speed friction screw press with motor, friction screw drive as is where is, WITHOUT putting into operation

Condition: used, Year of construction: 2007, pressure 100 t stroke 500 mm table surface area 900 x 600 mm rapid traverse 22 mm/s stroke speed 2 mm/s ram surface 700 x 350 mm total power requirement 2,2 kW weight of the machine ca. 1,6 t dimensions of the machine ca. 1,9 x 0,85 x 2,3 m The machine is of the Italian make SICMI, which was traded by the Knuth company. Ndedsvprv Ropfx Aamjd

Condition: used, Technical details: pressure: 25 t stroke: 500 mm daylight dimension : table/slide up: 800 mm throat: 360 mm ram stroke: 500 mm ram speed - forward: 0,100 m/s ram speed - reverse: 0,45 m/s Table dimensions: 630 x 500 x 75 mm passage inside table: Ø 180 mm surface area of ram: 450 x 360 mm mortise hole in ram: Ø 32 mm Nsdpfsvc Awxex Aamsdd height over floor: 710 mm total power requirement: 8,75 kW weight of the machine ca.: 2,2 t dimension machine xH: 1,7 x 1,1 x 2,95 m Operation via two-hand control panel. (and one-hand operation) *

Condition: used, Year of construction: 2003, Technical details: Pressure: 60 t stroke: 400 mm table surface area: 700 x 700 mm passage opening in table: Ø 100 mm distance between columns: 700 mm distance between columns: 700 x 1300 mm table height over floor: 850 mm dayligth: max. 1150 mm daylight dimension : table/slide up: 400 - 800 mm cylinder diameter: Ø 110 mm total power requirement: 4,8 kW machine weight approx.: 930 kg dimension machine xH: 1,2 x 0,7 x 3,0 m HYDRAULIC DOUBLE COLUMN PRESS Special construction welded from 25 mm sheet steel Operating mode: single stroke Ndjdpfxjvrygio Aamed Punch holder: pin M 70 x 2.5mm and punch Ø 128 x 440mm Table protection housing Round punch Ø 130 x 120 mm Hydraulic unit *

Condition: used, Year of construction: 2022, Technical details: Pressure: 30 t stroke: 142,5 mm table surface area: 500 x180 mm passage opening in table: 500 x160 mm Nedpfx Aaou N A Eaomedd distance between columns: 1000 mm daylight dimension : table/slide up: 120 - 1020 mm machine weight approx.: 176 kg dimension machine xH: T: 0,8 x 0,8 x 1,8 m Simple hydraulic double column press - special construction welded from 20mm sheet steel. Table support with prism 260 x 205mm Lower beam installation height max./min.: 1031 / 151mm Table height above floor max./min.: 1290 / 300mm Vertical lower beam, adjustable, manual, 10 steps, 100mm distance between steps Plunger cheek Lifting cylinder Ø 63mm with plunger holder Trunnion bore Ø 25 x 25mm *

Condition: used, Year of construction: 2001, Technical details: Ndsdpfx Ajxna Uzoamsd pressure: 250 t throat: 360 mm distance table/ram: 800 mm max. ram stroke: 500 mm ram speed - reverse: 390 mm/sec. ram speed - forward: 450 mm/sec. hydraulic-pressure: 280 bar connected load: 43 kW work speed: 11....50 mm/s operating pressure: 20 MPa total power requirement: 20,5 kW weight of the machine ca.: 17 t dimension machine xH: 3,9 x 1,9 x 4,0 m

Condition: new, The KNWP 30 M is a reliable manual workshop press within the Workshop Presses category, ideal for various pressing tasks, including assembly, testing, and straightening workpieces. Made in Europe, this robust machine combines a rigid, machined weldment structure with a versatile hydraulic pump, which can be operated via both hand and foot controls. Its sophisticated two-step hydraulics allow for seamless transitions between quick-stroke and work stroke, while an automatic reset piston ensures efficient operation, adjustable via a throttle valve. The support table, easily adjustable in height, enhances usability and comes with a multi-function die for effective straightening of both flat materials and corrugation. Whether for straightening beams or material testing, the KNWP 30 M provides the power of a 30 t pressure force with a total piston stroke of 160 mm, making it a must-have in any mechanical workshop, garage, or locksmith's shop. For more information or to place your order, please request a quote today. Ndjdpfxouyh Sge Aamsd

Condition: new, pressure: 70stroke: 500table area: 700x500daylight: 600rapid traverse: 25working speed: 5motor: 4messurements (LxWxH): 1400 x 900 x 2250weight approx.: 1900Features:Two-stage hydraulic pump – integrated into the machine frame Ndjdpfx Aaswwx Axsmjd Lever and push-button control – with simultaneous two-hand operation for safety Cylinder stroke: 500 mm – suitable for a wide range of applications Milled lower worktable – solid and precision-machined Two working speeds – for fast yet accurate operation Adjustable maximum pressure – adaptable to different tasks Integrated pressure gauge – for precise pressure monitoring during operation