Eccentric press

Weingarten XOR 2 ( 3919 )

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Gsdpfxjk S Htxe Aciokb Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: used, Year of construction: 1971, pressure 200 t passage width NA mm stroke 180 mm table length 690 mm table width 530 mm distance between columns 420 mm total power requirement 18 kW weight of the machine ca. t dimensions of the machine ca. m Gkjdpjt Hw Dwsfx Acijb Hydr. 4-Pillar Press for Embossing/Calibration

Condition: good (used), pressing force: 50 t, stroke length: 320 mm, Capacity 50 Ton Gksdpfxett A T To Aciob Throat 225 mm Adjustable stroke 8 - 100 mm Number of strokes 320 p/min Ram size 300 x 280 mm Table size 500 x 800 mm Machine LxWxH: 160 x 120 x 260 cm Machine weight: 6 Ton

Condition: good (used), Year of construction: 2000, Capacity Kg 15000 Table Length 400 mm Table Width 300 mm Hole in table 150 mm Working height 280 mm Throat 2170 mm Stroke 50 mm Ram adjustment 4 - 80 mm Hydraulic Clutch CE-Safety 2e hand opperator system Adjustable stroke / ram  Full set books / drawing / CE-Mark Length:1500mm Width:1500mm Height:2100mm Weight:1500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details! Godpfxoyc R Uie Acijkb

Condition: new, Year of construction: 2024, pressure 20 t throat 155 mm stroke 6-60 mm no. of strokes 84-210 Hub/min ram - range of adjustment 50 mm 300 mm table surface area 300x450 mm table height 840 mm hole in the table Ø 90 mm ram surface 190x278 mm tool hole in ram Ø 25 mm Gksdpfx Acsvfhp Ssieb total power requirement 1,5 kW weight of the machine ca. 1,0 t dimensions of the machine ca. BxTxH 1100x1100x1900 mm

Condition: good (used), Year of construction: 2000, pressing force: 15 t, table width: 300 mm, table length: 400 mm, Hydraulic clutch CE-Safety 2e hand opperator system Adjustable stroke / ram  Full set books / drawing / CE-Mark Note in the Neck / Throath machine is repaired ! Only EUR 5500 Capacity Kg: 15000 Table Length: 400mm Gsdsyc R Nmjpfx Acijkb Table Width: 300mm Hole in table:150mm Working height:280mm Throat: 2170mm Stroke: 50mm Ram adjustment:4 - 80mm Length: 1500mm Width: 1500mm Height: 2100mm Weight: 1200kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Table size: 350 x 350 mm. Gkjdpjfm A Amsfx Acieb

Condition: used, Year of construction: 1980, functionality: fully functional, Spindle press from Hiller & Lutz Year of manufacture: 1980 Fully functional In good used condition. Price reduced!!!!! Technical data on Gemini-Google: The Hiller & Lutz HP71 is a classic, robust manual spindle press (often also referred to as a piercing press), which is primarily used in locksmith shops, workshops, and the metalworking industry for tasks such as straightening, bending, pressing, or punching. Here are the common technical specifications for this model: Technical details (approximate values) Since these machines were manufactured over decades, details may vary slightly depending on the year of manufacture: Pressing force: approx. 20 to 25 tons (The designation "71" often refers to the size/frame width; the force results from the spindle pitch and the flywheel diameter). Spindle diameter: approx. 70 – 80 mm Stroke: approx. 200 – 300 mm (depending on the spindle length) Overhang: approx. 250 – 300 mm (distance from the center of the spindle to the stand) Table area: approx. 500 x 400 mm Through-height: max. approx. 400 – 500 mm (with the spindle rotated upwards) Flywheel diameter: approx. 1,000 – 1,200 mm Machine features Construction: Solid cast iron frame in C-shape for high rigidity. Drive: Manual, via the large flywheel; the energy is generated by the inertia of the wheel when the spindle is screwed down. Table: Usually equipped with a central through-hole and T-slots for tool attachment. Weight: The weight typically ranges between 700 kg and 950 kg, which guarantees a stable position (usually requiring bolted mounting to the foundation). Gemini says The dimensions of the Hiller & Lutz HP71 depend heavily on whether you are considering only the body or the total space required, including the flywheel overhang. Here are the specific dimensions for this model: Machine base dimensions (body) Height: approx. 1,800 mm to 2,100 mm (depending on the spindle position). Width (stand): approx. 500 – 600 mm. Gksdewxyn Eopfx Acijb Depth (foot): approx. 800 – 1,000 mm.

Condition: used, Year of construction: 1970, pressure 1 t Stroke 315 mm Godpfsv Td Erjx Aciokb

Condition: good (used), Stock number: 2829 Manufacturer: Eisenwerk Hensel Bayreuth - EBU Machine number: P5044070 Type: SK 25 Press force: 25 t Table: 595 x 410 mm Ram: 170 x 150 mm Passage hole: 210 x 170 mm Throat depth: 200 mm Strokes per minute: 150 Stroke: 4 to 80 mm Ram height adjustment: 70 mm Table adjustment: 240 mm Condition: good Gkedpfx Acjx Uwb Ioiob Connection: 1.5 HP (1.1 kW) Weight: 1.5 t Dimensions: 800 x 1,300 x 2,000 mm