Plate Shear - Hydraulic

STÜCKMANN & HILLEN 165.03

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm Ihjdpfjhzbipjx Aalow IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, Year of construction: 1980, machine/vehicle number: xxxx, Lg.no. 24211 Technical data approx: - max. working width 1020 mm - max. material thickness at 40 kg/mm² strength 1.5 mm - man. back gauge adjustable up to 550 mm - front angle stop - sheet hold-down device - Table size 1100 x 650 mm - Working height 900 mm - Space requirement approx. W 1800 x H 1450 x D 850 mm - Weight approx. 400 kg - mobile Iodpfxet H I Aqe Aaljhw

Condition: new, back gauge: 750 mm, - Capacity 1050 x 6 mm - NC electric back gauge Ijdpfx Aegg N Hbsalshw - Foot switch - Rear photocell protection - Support arms - Cutting line illumination - Brake motor - Emergency stop - Documentation - Weight 1800 kg - 400V

Condition: good (used), Automatic drawer warehouse is the ideal system for the vertical storage of steel bars and profiles with lengths of 3 m, 6 m and 12 m, heavy accessories, semi-finished products, components, molds and long material in general. The capacity per load unit ranges from a minimum of 5000 kg to a maximum of 6000 kg. Isdpfevvlntex Aaljhw

Year of construction: 1980, condition: good (used), Offer 22501 Iedpfxskzik Ho Aalohw Technical data approx: - max. working width 1020 mm - max. material thickness at 40 kg/mm² strength 1,5 mm - man. backgauge adjustable up to 550 mm - front angle stop - sheet holding-down device - table size 1100 x 650 mm - working height 900 mm - space requirement approx. W 1800 x H 1450 x D 850 mm - weight approx. 400 kg - mobile

Condition: good (used), Year of construction: 2010, operating hours: 100,000 h, pressure (min.): 10 bar, pressure (max.): 10 bar, type of cooling: water, Equipment: documentation/manual, refrigerant dryer, type plate available, Atlas Copco Screw Compressor GA 18 - 10 FF Fully automatic, internally completely piped and wired compact unit, single-stage oil-injected compression, air-cooled, sound-insulated, integrated refrigerant dryer (WorkPlace Air System™). Technical specifications Reference conditions: intake pressure 1 bar Intake temperature 20 °C Relative humidity 0 % Usable volumetric flow at the outlet of the compact unit at operating overpressure 9.75 bar 49.4 l/s 2.96 m3/min according to ISO 1217-3, C Motor rated power 18 kW Motor rated speed 4867 min-1 Ijdpfx Asu Rptysalehw Shaft power requirement at maximum operating overpressure 24 kW Shaft power requirement at idle 5.6 kW Compressed air temperature after dryer 23 °C Cooling air volume 0.23 m³/s Oil fill quantity 12.2 l Residual oil content under reference conditions

Condition: good (used), Year of construction: 1992, machine/vehicle number: 9207102, Offer 12001 Technical data: - material thickness 1,25 mm - max. throat 180 mm - roller center distance 63 mm - max. material thickness at 40 kg/mm² strength 1,25 mm - working speed approx. 6 + 12 m/min - drive 400 V / 0,7 / 0,85 kW - space requirement approx. W 550 x H 1250 x D 1000 mm - weight approx. 120 kg - with: - E - foot switch Ijdpfx Aasi Hpmtelshw

Year of construction: 2020, condition: ready for operation (used), A Rico compressor system consisting of two Atlas Copco compressors, two refrigerant dryers and an Atlas Copco Beko oil-water separation system is available. Screw compressor Atlas Copco GA 45 VSD+, year of manufacture: 2020, air volume flow: 9.4m³/min, operating pressure: 13bar, motor power: 45kW, motor speed: 4500rpm, machine dimensions X/Y/Z: approx. 1200mm/1100mm/2000mm, weight: approx. 860kg. Screw compressor Atlas Copco GA 45 VSD FF, year of manufacture: 2012, power: 45kW, operating pressure: 18.5bar, speed: 3000rpm. 2x refrigerant air dryers Atlas Copco FX 15, air volume flow: 15m³/min, operating overpressure: 13bar, pressure drop: approx. 0.3bar, refrigerant: R410A, refrigerant charge: 2050g, max. inlet air temperature: 60°C, machine dimensions X/Y/Z: approx. 900mm/750mm/1000mm, weight: approx. 160kg. Compressor management system Atlas Copco Equalizer 4.0/ES6-MK5, control range: 2-6 compressors. Oil-water separation system Beko ÖWAMAT 15, throughput range: 6m³-30m³/min, oil outlet: DN40, container volume: 115.5l, filling volume: 84.3l, oil collection container: 2x10l, max. operating pressure: 16bar, machine dimensions X/Y/Z: approx. 1100mm/550mm/800mm, weight: approx. 40kg. System operating hours: 8656h, controller hours: 42334h. Documentation available. An on-site inspection is possible. Ijdpfx Ajxdc Uvoalehw

Condition: good (used), Year of construction: 2008, Table size 1600 x 750 mm, table load 1500 kgs, Traverses XYZ 1525 x 762 x 625 mm, rapid feedrates 24m/min, Spindle power 18.5 Kw, spindle speed 6,000rpm, Iodpfxsxwytcs Aalehw 40 station ATC, spindle taper BT50, through spindle coolant, swarf conveyor, Fanuc 21i control.

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MILLING SPINDLE - Tool holder type : BT50 - Spindle power : 40 [kW] - Spindle speeds : 12000 [rpm] - Gearbox - Speed ranges : 2 LINEAR AXES - Travels on X/Y/Z axes : 2400/1650/1750 [mm] - Rapid traverses rates (X/Y/Z) : 42 [m/min] - Cutting feed rates (X/Y/Z) : 20 [m/min] B ROTARY AXIS - Travel : 360 [°] - Indexing precision : 0.001 [°] TOOL CHANGER - Auto. Tool Changer type : Bras chargeur - Tool magazine capacity : 116 - Tool exchange time : 3.8 [sec] PALLET CHANGER - Pallet changing device type : Rotopalette - Pallet size : 1600 x 1250 [mm] - Pallets number : 2 - Maximum weight upon pallet : 5000 [kg] - Distance table center / spindle nose (min./max.) : 100 - 1750 [mm] - Maximum workpiece diameter : 2500 [mm] - Maximum workpiece height : 1850 [mm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 86 [kVA] WEIGHT & DIMENSIONS - Machine floor space : 9.485 x 6.155 [mm] - Machine height : 4.370 [mm] - Machine weight : 50000 [kg] MACHINE HOURS - Number of working hours : 15446 [h] EQUIPMENT - CNC : Fanuc 31i-model B5 Interface : Ethernet / RS232 / USB / PCMCIA - SOFT SCALE II - Electronic handwheel - Rigid tapping - 3 colors status lamp - Coolant tank * with high-pressure pump : 70 [bars] * Coolant through spindle Iedpfx Aaow Ephbeljhw * with paper filtering unit * with cooling unit for coolant * With washing gun * With cabin washing - Chips conveyor - Spindle cooling unit - Tool probe - Workpiece probe : Renishaw RMP60 - Tool breakage detection : SOFT AC - Pallets number : 2 - Milling vice - Tool-holders