Gantry slitting machine Automatic knife

Rosen Technology S.R.L SLM-A1700

Condition: ready for operation (used), A 4-color Padane single-cylinder counter-printing machine with 4 inking units in pressing operation is available. Printing units: 4, repeat range: 280mm-650mm, max. printing width: 780mm, max. foil width: 810mm, cliché thickness: 2.84mm, printing process: single-sided, max. roll diameter: 600mm, number of cliché cylinders at 270mm: 2, number of cliché cylinders 280mm-650mm: 4, machine dimensions X/Y/Z: approx. 7500mm/2600mm/3000mm. Documentation available. On-site inspection is possible. Expected to be available from June 2025. Knsdpfx Aowdwzaoa Esf

Condition: excellent (used), Year of construction: 2016, operating hours: 27 h, SBL 1060 SE Year: 2016 Sheet feeder: Manual non-stop pile feeder Material range: Paper and board from 470 × 350 mm to 1060 × 760 mm Max cutting format: 1050 × 740 mm Min sheet size: 470 × 350 mm Max sheet size: 1060 × 760 mm Max cutting pressure: 300 tons Material thickness: 0.1 – 2 mm (corrugated/laminated max 4 mm) Min gripper margin: 9.5 mm Max inside chase size: 1155 × 852 mm Cutting plate size: 1076 × 756 mm Knjdpfjwypp Ijx Aa Esf Max speed: 8,000 sheets/hour Power consumption: Total 32 kW (22 kW + 10 kW for lower plate heating) Machine dimensions (L×W×H): 5,900 × 5,700 × 2,615 mm Max pile height – feeder (with pallet): 1,750 mm Max pile height – delivery (with pallet): 1,450 mm Feeder Section - Pneumatic feeder table - Non-stop manual feeder system - Anti-static system - Pre-pile device - Manual suction group adjustment - Micrometric suction adjustment - Motorized side pile adjustment - Suction belt feeder table - High-pressure lubrication pump - 2 pneumatic side register guides - Electronic control of front and side register Cutting/Embossing Section - Automatic pressure adjustment up to 300 tons - Preparation and introduction table for die frames in platen - 2 quick-lock die chase frames with bottom plate - Pneumatic locking of the chase and lower supporting plate - Centerline System - Micrometric system - Heated lower support plate (24 mm) - Cutting plate: 4 mm - Compensation plate: 3 mm - Archiveable 1 mm thin cutting plate Stripping Section - Quick lock for upper and central stripper frames - 2 standard upper stripper frames - 2 standard lower stripper frames - Double accessory kit for lower stripper prep (pins, bars, clamps, etc.) Delivery Section - High-pile automatic non-stop delivery with conveyor - Guillotine for automatic removal of gripper margin waste - Sheet deceleration device - Tab insertion device

Condition: like new (used), Year of construction: 2013, Grafisk Maskinfabrik Rewinder/Slitter Knjdsipvhnopfx Aa Esf

Condition: excellent (used), Year of construction: 2016, 1 used rapid steam generator ----- Manufacturer: CERTUSS Type: Universal TC Capacity: 700 kg/h Maximum heat output: 459 kW Operating pressure: 10 bar Water capacity: 103.5 l Test pressure: 57 bar CE mark: CE 0035 Year of manufacture: 2016 Knsdpfx Aswhxh Aea Eof Equipped with a Certuss gas burner, gas control system, control cabinet with touch control, mounted on the boiler body, and the existing coarse and fine fittings

Condition: good (used), Year of construction: 1989, 2-color "straight" offset machine with low-stack explanation; 48x66cm, last modified type of this model (= best) Kjdpfx Aaotyqhqe Eenf

Condition: excellent (used), Year of construction: 1988, functionality: limited functionality, machine/vehicle number: 25.05.004, total length: 9,500 mm, total width: 2,250 mm, total height: 2,300 mm, input voltage: 380 V, power: 50 kW (67.98 HP), overall weight: 21,000 kg, empty load weight: 18,000 kg, compressed air connection: 7 bar, Equipment: documentation/manual, Paper size: 730 x 1060 mm, printing area: 710 x 1040 mm Paper thickness: 0.05 mm – 0.5 mm Preset maximum speed (due to simulation of the throw-off time for high-speed presses) is 4,000 sheets per hour, but the machine can operate much faster for commercial jobs. Four-fold central impression cylinder that prints all 4 colors in one gripper closure. 1988 FAG Speedproof with operator console for ink duct and cylinder adjustments, enabling extremely accurate register printing. Attached is the original factory brochure. The machine has been fully dry ice cleaned, and the cylinders are in excellent condition. Offered strictly on an 'as is, where is' basis. Maximum width is 225 cm, maximum height is 230 cm; shipping in a High Cube container is possible. Price is absolutely fixed, based on the removal of easily separated parts which we could sell separately, such as the Mabeg feeder with vacuum belt delivery, and the four-fold Baldwin stainless steel unit—with each color having its own bath, a mixer, and adjustable temperature control, so all four baths can be set to different temperatures and alcohol concentrations. The machine was dry ice cleaned, and it was intended for prominent use in printing electronic paper. However, due to too many initial losses, the project was discontinued. The machine has been with us for 3 years and, due to its size, I want to sell it as quickly as possible. Hence this very low price. It is an excellent machine. If the machine needs to be set up for testing and sampling, this is possible at an additional cost of €10,000, of which €5,000 must be paid in advance as a deposit under agreed conditions. All relevant information can be found in the original FAG folder for the machine, available via this advertisement as a PDF. Technical Data - Printing size max.: 710 × 1040 mm (27.95 × 40.94 in.) - Paper size max.: 730 × 1060 mm (28.74 × 41.73 in.) - Paper size min.: 500 × 700 mm (19.68 × 27.56 in.) - Stock thickness: 0.05 – 0.5 mm (0.002 – 0.020 in.) - Plate size max.: 800 × 1080 mm (31.50 × 42.50 in.) - Plate thickness: 0.25 – 0.5 mm (0.010 – 0.020 in.) - Speed max.: 4,000 sheets/h - Floor space requirement (incl. access to feeder, delivery, and central control desk): 950 × 525 cm (374 × 206.69 in.) - Press height: 230 cm (90.55 in.) - Weight (including paper stacked in feeder and delivery): approx. 18,000 kg (approx. 39,690 lbs) - Total power requirements: approx. 50 kW Knjdpfxeuf Sy Ao Aa Esf - Compressed air supply: 6 – 7 bar

Condition: like new (used), Year of construction: 2015, Reel width: 2000 mm Slitting width 300 – 1700 mm Max unwind diameter: 800 mm Max. rewind diameter: 600 mm Slitting method: Razor Rewind shafts: Dual rewinding shafts Max mechanical speed: 400 m/min Knedewvv Hfopfx Aa Eef AC Servo motor with tension control Web guiding Material types BOPP, PET, PE, laminated film, foil, paper

Condition: used, Year of construction: 2022, Technical details: rated capacity: 28 kVA drive motor: 24 kW Number of working hours: 0 h type of fuel: Diesel revolutions per minute of the motor:: 1500 - 1800 rpm motor capacity: 24 kW voltage: 400 V weight of the machine ca.: 1060 kg dimensions L x W x H: 2,0 x 1,0 x 1,3 m The generator is silent. NEW Engine: 4-cylinder; type Cummins 4B3.9-G2; 1,500 rpm; output power 24 kW; tank capacity 120liter; fuel consumption: 238 g/kWh rated power and 226 g/kWh standby power. Cooling system and battery 12Volt Generator: Type TAL-A40-G; voltage 400Volt; 1,500 - 1,800 rpm; current 40Ah; power max. at standby power=28kVA and primary power=25 kVA. Knjdpfx Aaou U E Nve Esf Accessories: Service box see photo *

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, overall weight: 52,000 kg, punching force: 600 t, space requirement height: 3,520 mm, space requirement length: 12,150 mm, space requirement width: 9,340 mm, Machine for punching, embossing, waste stripping and blanking Used machine, overhauled at the QTM Schwalmtal plant System equipped with high-performance sheet feeder for NON-STOP operation ⦁ For fully automatic punching, creasing and embossing with or without gripper edge ⦁ for stripping the inner waste as well as the side and rear sheet edges ⦁ for stacking the punched and stripped sheets with the attached gripper edges or the attached gripper edges or ⦁ for cutting off the gripper edges and then depositing the remaining sheets in stacks remaining sheets ⦁ with a patented gripper carriage register system for maximum register accuracy ⦁ with a bundle stacking machine that features a fully automatic separating sheet feeder and NON-STOP delivery and does not need to be converted even for the smallest blanks. changeover even the smallest cuts. (Shuttle table with comb structure) ⦁ Cut-off sheet magazine with electrical stock control, during production refillable during production ⦁ with Centerline equipment ⦁ with automatic pallet changing device in the storage area ⦁ Modem ⦁ Standard elevation of the machine 600 mm Specification Sheet format max. 1060 x 1450 mm Sheet format min. 500 x 700 mm Maximum punching force 6.0 MN (600t) Speed 8,000 Bg / h Processable materials: Ksdst E Nthspfx Aa Eonf Paper min. 80 g/m² Cardboard up to 2000 g/ Corrugated cardboard up to 5 mm (max. sheet curvature 4 %) Features: patented QTM rail system manual non-stop feeder stripping station depaneling station Centerline Fully automatic pallet changing device Deposit incl. platform Upgrade of the control system to Siemens S7 Completely overhauled machine drive Quick-clamping frame in all tool stations

Condition: good (used), Year of construction: 2003, functionality: fully functional, section length (min.): 4,430 mm, M&R sportsmann, made in the US. this is a very reliable and accurate printing machine in a good working condition. She is 100% accurate and has prove that she is worth her money. More information, pictures or videos upon request. Knjdpeuyhkisfx Aa Eof Machine has extra set of plates.