Eccentric press

Pressix T50 CNR4

Condition: used, Single-column – Eccentric press WEINGARTEN Type EV 63 Machine No. 738 / 61 Year of manufacture 1962 Pressing force 63 tons Stroke 260 mm Table area 630 x 530 mm Table opening Ø 210 mm Slide area 315 x 260 mm Adjustable slide stroke 8-100 mm Slide adjustment 63 mm Tool holder bore Ø 40 mm, with clamping piece Installation height max 450 mm Stroke rate 115 strokes / min Compressed air requirement min. 4.5 bar Motor power 4 kW Power connection 380 Volt, 50 Hz Rjdjk S Htxspfx Ablsw Table height above floor approx. 750 to 900 mm - Electrical stroke release via foot switch or two-hand control - Overload protection by shear plate - Clutch-brake combination by WEINGARTEN friction-thread clutch with top dead center through-drive protection - Front crankshaft support bearing - Press table adjustable in height via 2 threaded spindles - Manual centralized lubrication - Control cabinet positioned beside the press - UVV (German trade association for accident prevention) for manual feeding operations Space requirement L x W x H 1750 x 1600 x 2430 mm Weight 4.5 tons Good condition

Condition: used, Year of construction: 1981, pressure 080 t throat 345 mm stroke 8 - 112 mm Stroke rate 65 / min Distance table/ram, max. stroke up, adjustment up 472 mm Table surface area 840 x 610 mm Hole in the table 280 / 315 mm Table height above floor 800 mm Passage to the back 500 mm Ram surface 650 x 400 mm Ram adjustment 70 mm Power capacity 7,5 kW Weight 6,8 t Dimensions (WxDxH) 1,2 x 1,95 x 3,05 m with motor, pneumatic clutch-brake combination, hydraulic overload protection in ram, manual stroke adjustment, manual ram adjustment, pneumatic counterbalance in ram, motoric centralized lubrication, two-hand operation Rodpfxevuua Aj Ablsw

Condition: good (used), Year of construction: 2000, Capacity Kg 15000 Table Length 400 mm Table Width 300 mm Redpfoyc R Uijx Abljw Hole in table 150 mm Working height 280 mm Throat 2170 mm Stroke 50 mm Ram adjustment 4 - 80 mm Hydraulic Clutch CE-Safety 2e hand opperator system Adjustable stroke / ram  Full set books / drawing / CE-Mark Length:1500mm Width:1500mm Height:2100mm Weight:1500kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, Year of construction: 2026, machine/vehicle number: 26.06.24, functionality: fully functional, Fresan FP 80P - C Frame Eccentric Press - 80 Tons (800kN) TECHNICAL DATA: * Power: 80 tons (800kN) * Strokes Per minute: 60 (variable) * Ram-Table Distance: 400 mm * Stroke Adjustment: 0 - 112 mm * Ram Adjustment: 80 mm (motorized) * Table Dimensions: 600 x 900 mm STANDARD SPECIFICATIONS: * Conformity to CE safety regulations * Welded steel frame * Crankshaft made of AISI 4140 (42CrMo4) alloy steel. Highly durable and ductile. CNC ground for minimum surface friction. * SnBz-12 quality bronze bearings * Pneumatic clutch-brake combination * Fully closed gearbox with helical gears working in oil * Double body press safety valve * Safety PLC & light curtains & safety switches (Pilz) * Ram with 6 slides & waste oil collector * 7-inch HMI touchscreen operator panel Rodpjnxh Hrefx Ablsw * Speed control with AC inverter * Motorized ram adjustment * Mechanical fuse for overload protection (Hydraulic fuse can be installed on standard a machine after purchase) * Pneumatic counterbalance cylinders (ISO, 4 pcs) * Automatic central lubrication & used oil collectors (Thin oil / slideways oil) OPTIONAL EQUIPMENT: * Additional work table * Part ejector mechanisms(upper and/or lower ejectors) * Material feeding, loading & unloading systems (Decoilers, straighteners, pneumatic & servo feeders...) * Special design / customized machine

Condition: used, Year of construction: 1991, pressure 60 t throat 280 mm stroke 10 - 90 mm ram adjustment 60 mm no. of strokes 110 Hub/min table surface area 740 x 550 mm clamping plate 740 x 555 mm ram surface 380 x 200 mm daylight, max. stroke above - ram adjustment above 360 mm total power requirement 4 kW weight of the machine ca. 3850 kg Rodpfxsv Az T Ss Ablew dimensions of the machine ca. B 1,1 x T 1,6 x H 2,3 m - fixed table - clamping plate - hydraulic clutch Ortlinghaus with additional brake - manual central lubrication Machine is partially overhauled in our company as follows: - disassembled, cleaned and completely technically inspected - new colour - shaft pulling, crack inspection, new seals - new control cabinet with touchscreen - new braeke plate - current press inspection

Condition: used, Year of construction: 2000, pressure 075 t throat 295 mm stroke 16 - 140 mm Stroke rate 75 / min Distance table/ram, max. stroke up, adjustment up 450 mm Table surface area 800 x 595 mm Hole in the table 330 x 230 mm Table height above floor 745 mm Ram surface 470 x 180 mm Ram adjustment 80 mm Rodpjvut Hhjfx Ablew Power capacity 5,5 kW Weight 5,0 t Dimensions (WxDxH) 1,5 x 2,5 x 2,5 m overhauled by the manufacturer in 2000 with motor, pneumatic clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, fix table, motorized central lubrication, two-hand and foot operation

Condition: used, Year of construction: 1993, pressure 80 t throat 280 mm stroke 10 - 140 mm Stroke rate 85 / min Distance table/ram, max. stroke up, adjustment up 380 mm Table surface area 850 x 560 mm Hole in the table 300 x 200 mm Table height above floor 790 - 950 mm Ram surface 420 x 210 mm Rodpfx Asyx Ikueblow Ram adjustment 60 mm Power capacity 4,0 kW Weight 4,5 t Dimensions (WxDxH) 1,3 x 1,4 x 2,45 m permitted only for safe tools or fixed screen according to the German Safety Regulations (UVV) with motor, rolling-key clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual centralized lubrication, foot operation can be inspected in running condition in our warehouse

Condition: used, Year of construction: 2002, pressure 80 t throat 300 mm stroke 8-110 mm no. of strokes 100 Hub/min ram - range of adjustment 75 mm table surface area 750x590 mm ram surface 540x400 mm hole in the table 200x200 mm table height 780 mm tool hole in ram Ø 40 mm Rjdpfx Asy I Dd Noblow total power requirement 11 kW weight of the machine ca. 5,5 t dimensions of the machine ca. BxTxH 1200x1700x2700 mm

Condition: used, Eccentric Press, C-Frame Press, Helmerding EH 35 B, Used Machine Manufacturer: Helmerding Type: EH 35 B Year of Manufacture: 1985 Weight: 2500 kg Technical Specifications: Press Capacity: 35 tons Stroke Length: 70 mm Table Dimensions: 600 x 450 mm Rsdpfx Aoy D Uhdsblow Operating Modes: Continuous / Single stroke (Inching) Safety: Two-hand safety start control Dimensions: Overall Dimensions: 1020 x 1600 x 2400 mm Additional Information: Note: The base plate (bed plate) is not included with the machine.

Condition: used, Year of construction: 1959, pressure 063 t Redpfxeyx Ih Hj Ablew throat 280 mm stroke 8 - 100 mm no. of strokes 65 /min distance table/ram, max. stroke up, adjustment up 550 mm table surface area 630 x 500 mm hole in the table 230 mm table height over floor 740 mm table adjustable 200 mm ram surface 320 x 260 mm ram adjustment 63 mm power capacity 5,5 kW weight 4,6 t Dimensions (WxDxH) 1,4 x 1,8 x 2,4 m permitted for manual loading according to the German Safety Regulations (UVV) with motor, friction clutch, mechanical overload protection in ram, manual stroke adjustment, manual ram adjustment, adjustable table, manual centralized lubrication, two-hand operation Press is currently under revision