Rolls bending machine - 3 Rolls

PEKRUN 2000 / 6

Condition: used, Max. bending length: 2000 mm Max. sheet thickness: 8 mm steel Clockwise and counterclockwise rotation Mechanical rear roller conveyance Dwsdjmhm Eljpfx Acysd Emergency stop switch Conical rounding possible

Condition: new, functionality: fully functional, The EVO is the latest innovation in sheet metal processing. It is equipped with numerous innovative and patented features that increase your production capacity and productivity, while offering the lowest total cost of ownership. The high-quality components used in this machine and the latest version of the BENDtronic® control system, which is installed as standard on all EVO machines, are particular highlights. Available from stock: HAEUSLER EVO 31031 4-roll round bending machine / roll bending machine Manufacturer: Haeusler Type: EVO 31031 4-roll round bending machine / roll bending machine Origin: Germany / Switzerland Year of manufacture: 2024 Condition: NEW, exhibition machine Availability: immediately Performance: Working width 3100 mm Round bending capacity 14 mm Bending capacity 12 mm Not the right machine? As a representative of Haeusler, we can put together and offer you your desired machine according to your requirements. Dsdpjxwmb Hsfx Acyswd Please do not hesitate to contact us.

Condition: used, Year of construction: 1986, sheet width 2040 mm plate thickness 4,0 mm distance between columns 2100 mm roll diameter 150 mm total power requirement 7,0 KW weight of the machine ca. 2,2 t Dwjdpfxsy Ezzys Acyjd dimensions of the machine ca. 2,95 x 1,0 x 1,75 mm Sheet metal bending machine with 3 rollers - 2 driven rollers - Rear roller electrically adjustable - Conical bending - Foot switch - Emergency stop device

Condition: new, Year of construction: 2025, functionality: fully functional, total height: 5,600 mm, total length: 11,200 mm, total width: 5,100 mm, type of input current: three-phase, warranty duration: 24 months, inner dimension height: 4,970 mm, inner dimension length: 11,000 mm, temperature: 80 °C, inner dimension width: 5,000 mm, air demand: 52,000 m³/h, input voltage: 380 V, heating capacity: 250 kW (339.91 HP), power: 45 kW (61.18 HP), fuel: liquid petroleum gas (LPG), input frequency: 50 Hz, energy consumption: 45 kWh, insulation thickness: 50 mm, nominal power: 250 kW (339.91 HP), sheet thickness steel (max.): 2 mm, Equipment: lighting, * Air Preparation Unit: The air preparation unit is a recirculation system that supplies the cabin with filtered fresh air and exhausts used air during the painting process. It heats the air to 60 °C, mixes the used air with 10% fresh air via an automatic multi-damper system, and reheats the air before routing it back into the cabin. The air is heated using a burner and a heat exchanger, both made of high-quality 304 stainless steel and housed within the fresh air unit. During painting, the air is filtered twice (via front and ceiling filters) before it enters the cabin. The contaminated air is also filtered twice (through inlet and outlet filters) before it exits via the exhaust unit. Air preparation units are insulated like the side walls to minimize heat loss and are protected against potential vibration and noise thanks to rubber seals on the covers. The exhaust air is regulated by a damper in the outlet duct, which helps control the internal pressure of the cabin. * PRINCIPLES OF CABIN OPERATION: The processes in the cabin are controlled via a control panel that manages the following steps: * PAINTING PROCESS: During painting, 100% fresh air is drawn in from outside and passed through front filters before entering the distribution chamber at ambient temperature. The air is then expelled by the extraction unit. Floor filters (paint stops) capture paint particles, and the air passes through the final exhaust filters before being discharged. * FLASH-OFF PROCESS: Dsdpfxswzl Hxo Acyewd After painting, the cabin operates for approximately 15 more minutes to purge residual solvents and thinners. During this phase, fresh air from outside continues to circulate in the cabin. * DRYING PROCESS: In this phase, 80% of the air passing through the cabin is heated to 60 °C and supplied to the cabin via a distributor. As 20% of the solvent is released during drying, these solvents are expelled with the exhaust air. Industrial coatings are typically dried at 60 °C, but the cabin temperature can be adjusted via the control panel as required. * COOLING PROCESS: After the 30-minute drying process, the coil is deactivated via the control panel, the pneumatic damper closes, and the extraction system restarts. During the 5-minute cooling phase, fresh air from outside circulates in the cabin, after which the system stops automatically. ELECTRICAL AND ELECTRONIC EQUIPMENT: These control panels manage the functions and operation of all machinery and devices inside the cabin. The control panel is constructed from durable galvanized sheet metal and steel profiles and is fully enclosed to protect against dust and moisture. Electrical devices and control panels: • The control panel contains essential components such as circuit breakers, fuses, indicator lamps, thermal relays, contactors, and connectors. • Heat-resistant cables are used for command and control lines between the panel and motors or other electrical devices. • Electrical wiring is designed to allow for cabin relocation if necessary. • Operating devices use 380 V 50 Hz, while control devices use 220 V.

Condition: new, sheet width 3100 mm plate thickness 13 mm pre-bending 10 mm upper roll diameter 300 mm lower roll diameter 270 mm side roll diameter 210 mm total power requirement 11 kW Overall size 5600 x 1800 x 1500 mm weight of the machine ca. 8.800 kg Accessories / equipment: - Conical bending device - induction hardened rolls - digital display for side rollers - Machine made of steel construction - Separate control panel - two speeds Dwodpfx Acoyv Nh Neysd - all rollers on ball bearings - Folding and support bearing from the top roller is actuated from the control panel. When the folding bearing is opened, the roller moves automatically upwards. - Conical adjustment of the rollers via control panel - Central rollers are via hydraulic motor and rotary reduction gear driven. (Top and bottom rollers) - Calibration

Condition: used, sheet width 3000 mm plate thickness 6 mm pre-bending 4 roll diameter 205 mm total power requirement 5 kW weight of the machine ca. 3,7 t dimensions of the machine ca. 4,0 x 1,4 x 1, 5 m Roundo 3-roll plate bending machine, featuring: - Hydraulic drop-end bearing and remote control Dwedpfxe Ahkino Acyod - Conical bending attachment: a device for rolling cones and funnels.