Double Column Drawing Press -Hydr.

MÜLLER SLUZ 315-20.1.1 (UVV)

Year of construction: 1993, condition: used, TYPE: DEA 400/2000 Year: n.d. MAXIMUM RAM CAPACITY: 400 tons SLIDE STROKE: 1,100 mm Fodpfxsihf R Uj Ab Nogd MAXIMUM SHUT HEIGHT: 1,600 mm TABLE DIMENSIONS: 2,000 x 1,600 mm FAST STROKE: 650 mm/sec CUSHION CAPACITY: 160 tons CUSHION STROKE: 400 mm HEIGHT ABOVE GROUND: 5,800 mm DISTANCE BETWEEN UPRIGHTS: 3,400 mm LATERAL WINDOW: 1,600 mm

Condition: used, Year of construction: 1970, machine/vehicle number: 120895, pressure:63 t throat:250 mm stroke:8 - 100 mm Fodpfxefx Hv Hj Ab Nsgd no. of strokes:120 Hub/min table::715 x 500 mm dayligth:330 mm ram adjustment:63 mm clamping plate:700 x 480 mm hole in the table:240 mm Hole in clamping plate:110 mm dimension of ram:450 x 280 mm weight of the machine ca.:5,5 t dimensions of the machine ca.:1,2 x 1,7 x 2,7 m hydraulic tilting single column eccentric press, tilting in 4 steps, opening to rear (325 x 500mm) and below (360x160mm) with central lubrication via hand pump, additional clamping plate 700 x 480 x 850 mm, two-hand operation, foot-trip operation possible, operating-mode selector for adjustment of continuous or single stroke, emergency cut-off, piece counter, various accessories

Condition: ready for operation (used), Year of construction: 1998, power: 37 kW (50.31 HP), pressing force: 250 t, stroke length: 150 mm, table width: 900 mm, table length: 1,000 mm, overall weight: 16,000 kg, Very nice and well maintained hydraulic press. 250 tons pressing force. Approximate dimensions: Fodsry Trpspfx Ab Nsgd H: 380 cm. W: 200 cm. L: 200 cm. Weight: 16,000 kg. Can be loaded by crane on collection against payment. Transportation can be arranged. Sold for customers. Location: DK-7600 Struer. Make an appointment for a demonstration.

Condition: used, Year of construction: 2007, pressure 315 t distance between columns 1750 mm stroke 700 mm distance table/ram, max. stroke up, adjustment up 1200 mm table surface area 1600 x 1500 mm pressure of drawing cushion in table 125 t stroke of drawing cushion in table 200 mm die cushion area 1200 x 1400 mm table height over floor 750 mm ram surface 1640 x 1500 mm power requirement 55,0 + 11,0 kW weight 29,5 t dimensions (WxDxH) 3,2 x 4,5 x 5,8 m Height above floor 5,1 m year of manufacture 1983 - 2007: modernization of electrical control (Siemens S 7) with oil-hydraulic drive, hydraulic drawing cushion in table, hydraulic cutting impact cushioning Fgsdpfxevuukbo Ab Nod

Condition: ready for operation (used), Pressing force: 1600kN, throat depth: 450mm, installation height: 560mm, ram stroke: 8-160mm, controls: SCHMERSAL SEPG 05.3.2.0.22/ 95, weight: 16.2t, including documentation. Fsdpfxjhz Ua Se Ab Nsgd

Condition: new, Ostas 4-roll round bending machine 4R OHS 2070 x 220 Hydraulic side roller infeed Hydraulic folding bearing Hardened rolls Conical bending device Separate control panel Roller length : 2000 mm Top roller diameter : 220 mm Side roller diameter : 180 mm Total motor power : 4+3 KW Weight : 4900 kg Dimensions (mm) : 4050 x 1550 x 1470 (L x W x H) Performance data bending: 11 mm with smallest inner diameter (5 x top roll) 9 mm with smallest inner diameter (1.5 x top roller) Bending performance data: Fedpfxstvn D Tj Ab Nogd 9 mm with smallest inside diameter ( 5 x top roller ) 7 mm for the smallest inside diameter (1.5 x top roller) All bending capacities are calculated on the basis of 250 N/mm2 yield strength Material ( ST 37 - ST 42 structural steel ) Special accessories installed: Infinitely variable rolling speed: NC control:

Year of construction: 2020, condition: as good as new (ex-display), Hydraulic press for tests and retouching of dies Brand: MHG Model: ER.2S.DM-300/2100 Serial number: 927 Year: 2020 Required power: 40kw Hydraulic oil: 1000Ltrs. deposit + 200 liters. circuit filling Total number of cycles: 403 (NEW MACHINE, PRACTICALLY UNUSED) Maximum force: 300t Number of cylinders: 3 Maximum tooling dimensions: 1400x1400mm Maximum tooling mass: 16,000kg Fgodpfx Aok Sgvysb Nsd Maximum working table and mobile table opening: 1690mm Minimum opening of work table and mobile table: 960mm Maximum mobile table travel: 730mm Approach speed: 92 mm/s Recoil speed: 93mm/s Stop time: 0.2s Safety distance: 500mm Weight with empty tank: 35.000kg

Condition: used, Year of construction: 1991, pressure 400 t stroke 300 mm table surface area 1200 x 700 mm ram surface 1200 x 700 mm dayligth 500 mm adjustment of stroke 300 mm return capacity 348 kN capacity of ejector 100 kN ejector stroke 100 mm control SIEMENS Simatic S 5 total power requirement 65 kW weight of the machine ca. 28 t dimensions of machine L x W x H 4,4 x 2,75 x 4,0 m = hydr. punching and embossing press Fjdpfx Abjtqqlcj Negd Accessories: tool changing table - with cutting shock absorption damping force 4000 kN damping stroke 5 mm spindle adjustment 200 m

Condition: used, Year of construction: 2005, Pressure 800 t distance between columns 2560 mm stroke 1050 mm Distance table/ram, stroke up 1870 mm Table surface area 2500 x 1730 mm pressure of drawing cushion in table 300 t Die cushion stroke in table 395 mm Die cushion area in table 2300 x 1300 mm Ram surface 2500 x 1730 mm Die cushion pressure in ram 63 t Die cushion stroke in ram 150 mm Side window 1000 mm Oil volume 4300 l Power capacity 200,0 kW Dimensions (WxDxH) 4,1 x 2,8 x 10,0 m Height above floor 7,0 m Fgodpfx Abjvuuikj Nsd year of manufacture 1974 overhaul 2005: formerly type BZE 800, converted to ZE 800 by manufacturer with new ram and new cylinder mit ölhydraulischem Antrieb, hydraulischem gesteuertem Ziehkissen im Tisch und Stößel stored in dismantled condition - Video at seller’s site before dismantling available

Condition: used, MULLER 250t PRESSURE: 250t STROKE: 550mm Fodpfx Aorfxhkeb Nogd TABLE DIMENSIONS: 2500x1400mm