Section Shear

Mubea MIW 400

Condition: used, pressure 40 t throat 175 mm work height max. 1055 mm stroke 30 mm sheet thickness - max. 8 mm total power requirement 4 kW Klsdoyv Nuiopfx Aaljp weight of the machine ca. 1020 kg dimensions 910 x 670 x 1930 mm

Condition: used, Year of construction: 1996, Max. punching force: 55 tons Notching: 10 mm Kledpfswgkq Tex Aalep Hole diameter and thickness: 40x10 mm Flat steel: 300x15 or 200x20 mm 90° angle steel: 120x120x10 mm 45° angle steel: 70x70x7 mm Bar steel: 40 mm Square steel: 40 mm Strokes per minute with a 20 mm stroke: 37 /min Throat: 250 mm Machine weight: approx. 1,800 kg

Condition: used, Punching force: 400 kN (punches e.g. 20 m in 15 mm steel) Cuts 150 x 10 mm on the flat steel shears With pipe notcher on the bar shear Foot switch for stroke activation Support table on the punching side Quick change device Range of tools is included in the price Klsdpfx Aajw Im Shjljp

Condition: new, Year of construction: 2025, Bending machine ZB 70/2 M - with foot pedal - with standard roller set - two driven shafts - mecanical adjusting of the center roller - working position horizontal and vertical Klsdpfx Aot Hwfnjalop - shafts are supported by conical bearings - slide bars on the slide -support are exchangeable - shaft diameter: 40 mm - roller diameter: - shaft rpm: 8,5 U/min - voltage: 400V 50Hz 3Ph - drivingmotor: 1,1 kW - adjusting way: 120 mm - weight: 400 kg - dimensions: 900x600x1100 mm

Year of construction: 2023, condition: new, The sieve machine is ideal in combination with a crusher and / or mill for the exact separation of bulk materials. Kledpfoh R Twbsx Aaljp

Condition: ready for operation (used), Year of construction: 2019, Lifting capacity: 2000kg, lifting height: 4000mm, fork length: 1220mm, power: 41kW, fuel: gas, machine dimensions X/Y: approx. 2350mm/1000mm, operating hours: 1793h. Including attachment Bolzoni Shifter 5BSS200F, mast model: 5F20C40, tower height: 2500mm. Documentation available. On-site inspection is possible. Ksdpfx Aasv Ip Sgjlelp

Condition: new, pressure: 60stroke: 250total power requirements: 4weight approx.: 800messurements (LxWxH): 1.710 x 700 x 2.100Technical DataPress force: 60 tons Ksdpod Ab Iqofx Aalolp Motor power: 4 kW Stroke: 250 mm Clear distance between columns: 1,040 mm Piston Ø: 180 x 120 mm Feed speed: 8 mm/s Working speed: 4 mm/s Return speed: 10 mm/s Length: 1,710 mm Width: 700 mm Height: 2,100 mm Weight: 800 kg EquipmentSteel welded construction Any stop position Pressure gauge Safety valve against overload 2 V-prisms Height-adjustable table Table up/down device Control with operating lever Manual right/left cylinder movement Equipment according to CE regulations, operating manual in German and English

Condition: good (used), Year of construction: 2020, operating hours: 206 h, travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 88 mm, Waterjet Cutting Machine Multicam V-204-W with High-Pressure Pump KMT Streamline SL-VI 50 STD and Abrasive Feeder KMT Abraline V Year of manufacture: 2020 Operating hours: Only 206h !!! (read directly from the high-pressure pump) Complete documentation available. The cutting tank is fitted with grating supports. It can also be equipped with the original plastic supports (approximate cost: €3,000). (Y) Axis ... 1524 mm (X) Axis ... 3048 mm (Z) Axis ... 88.9 mm Position accuracy: +/-0.001″ Repeatability: +/-0.002″ Rapid traverse (max): 1000 IPM Cutting speed (max): 800 IPM Klodpoxg Nnnsfx Aalep EQUIPPED WITH: - KMT Streamline SL-VI 50 STD, 50 Hp (37 kW) – 500 - 3,800 bar - Dual side stepper motors - Multicam hand-held graphic interface - KMT Abraline V – Highly accurate abrasive feeding/hopper system

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Manufacturer: EHT Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Nominal current: 87 A. Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment Kodpfouddh Asx Aalelp

Condition: new, Hydraulic - sectional steel shears LFSS Typ. HKM 60 - 5 stations Including MUBEA - punch and die holder Including Ringsland - punch and die holder ::: PUNCH ::: Ø / sheet thickness: Ø 28 mm / 15 mm, Ø 38 mm / 11 mm, Ø 110 mm / 3 mm stroke: 55 mm number of strokes (20 mm): 26 / min throat: 220 mm Working height: 940 mm ::: STEEL SHEARS ::: Capacity round: Ø 40 mm capacity square: 35 mm ::: ANGLE SHEARS ::: Capacity 90°: 120 x 120 x 12 mm capacity 45°: 80 x 8 mm working height: 1140 mm ::: PLATE SHEARS ::: capacity: 200 x 20 mm, capacity: 300 x 15 mm, cutting length: 317 mm cutting with angle: 80 x 10 mm, working height: 940 mm Kljdpfx Aajgiplnslop ::: CUT-OUT ::: thickness: 10 mm, width: 42 mm, depth: 100 mm Working height: 940 mm Capacity: 60 to., Motor power: 4 kW, Voltage: 400 V Weight: 1440 kg Dimensions (LxWxH) 1520 x 950 x 1780 mm