Used Universal Grinding Machine for sale (64,589)

Condition: used, Year of construction: 2002, grinding diameter 450 mm grinding length 1500 mm centre height 225 mm Control FAGOR EQUIPEMENT - T1: grinding wheel diameter 500 mm - T2: grinding wheel diameter 400 mm - T6: HF Fischer spindle MFV or MFZ 1224/1242/1260 - T7: HF Fischer spindle MFV or MFZ 1224/1242/1260 - Marposs tool measurement - active longitudinal positioning - Elaso GAP-control on T1 and T2 contactless integrated in the control surface - Elaso GAP internal grinding with fluid sensor for T6 and T7 - semi-automatic balancing by Elaso integrated in the control surface for T1/T2 - tailstock hydraulic with fine adjustment +/- 150 microns - dresser on workpiece spindle side table mounted - dresser on tailstock side table mounted - dresser on upper table - new service- and userfriendly housing SPECIAL EQUPEMENT: Workhead with direct drive - strongly recommended for non-circular grinding - workpiece weight flying max. 75kg - workpiece weight between centres 150kg - water-cooled B-axis with direct drive - center height 225 mm - extremely torsionally stiff - highly accurate positioning - resolution ° - water-cooled Hydrostatic ball screw - x-axis - wear-free, as there is no contact during operation - no loss of precision, even during long-term use at full load and maximum speed - no friction at low speeds - no friction force backlash when the direction of rotation changes - translates even the smallest rotational movements - no stick-slip effect even at low speeds - no fluctuations in frictional torque due to ball circulation - higher axial stiffness compared to ball screws - significant improvement in damping, resulting in better workpiece surface finish and tool life - no oscillations due to ball circulation - also suitable for high speeds and accelerations - cost-effective alternative to the linear motor with greater precision and significantly lower heat generation - significantly less power dissipation and, as a result, no problems with swarf on permanent magnets New hydraulic unit - optimized temperature control (chiller) - Energy-saving Only one pump controlled by VFD - Pressure monitoring Bjdpfx Afeuxfu Ns Eecu - monitoring of the hydrostatic oil for water content. (Damage to the bellows is recognised and detected prematurely) -fine adjustment +/- 150 microns Paper belt filter 375l – alternative 480l Grinding mist extraction system – emulsion MECHANICAL OVERHAUL -complete machine according to Kellenberger protocoll -new painting ELECTRICAL OVERHAUL - new modern Fagor CNC with BEMA HMI - new electric cabinet - new digital drive technology - replacement of all electrical cables, switches etc. - new absolute external scales in x- and z-axis - new absolute encoder (B-axis) Grinding software BEMA-Standard: - workpiece zeroing - grinding wheel zeroing - dressing diamond measuring - corrections - external and internal surface grinding - external and internal angle grinding (turning of the b-axis, dressing with straight wheel) - external and internal radius grinding (radius dressed on wheel) - semi-automatic traverse grinding - workpiece zeroing - 2 dressing diamonds - 1 dressing blade - dressing roll - 3 flat dresser - corrections - Z-position measurement - GAP control Optional grinding cycles at no extra charge: Profile plunge grinding: - external and internal profile plunge grinding with profile wheel Pr...

Condition: used, grinding diameter 350,450 mm grinding length 600 mm centre height 175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±10 ° longitudinal feed of the table 900 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,2 t dimensions of the machine ca. 3,1 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Foto von bereits gelieferter Maschine mit eventuell anderen Optionen. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. BEMA Standard serienmäßig: -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my -Drehzahlanzeige Schleifspindel -Stufenlose Drehzahl Schleifspindel 70-100% -Stufenlose Drehzahl Innenschleifspindel 70-100% -Werkstückspindelantrieb durch Drehstrommotor stufenlos regelbar über Frequenzumrichter Mögliche Optionen gegen Aufpreis: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Sinuslineal -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter Natürlich erhalten Sie auf unsere generalüberhalten Maschinen 12 Monate Gewährleistung. (Nur Anrainerstaaten) weiteres Zubehör auf Anfrage. Bcsdsd Ih D Eopfx Af Eju Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln

Condition: used, grinding diameter 350 mm grinding length 1500 mm centre height 175 mm weight of the machine ca. 3 t High-End Kellenberger 1500U Ideal for spindle producer or overhauler -BEMA Internal grinding device with separate, cooled motor. Grinding spindle and internal grinding spindle motor electrically interlocked! Internal grinding spindle can only be switched on when it is in position. A quantum leap in safety -Infinitely variable grinding spindle speed 1000-1500 rpm -Infinitely variable internal grinding spindle speed 0-100%. -Digital display of grinding spindle speeds -Swivelling angle display top table -swivel angle display grinding headstock -Marposs gaper sensor for external grinding only -fluid gating sensor Marposs internal grinding Bodpfx Afet Ii Rrs Ejcu -Center height up to 250mm possible Machine is already delivered. Identical machine can be built with additional with additional options. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 2002, grinding diameter 250 mm grinding length 400 mm centre height 125 mm Control Fanuc 21i-T Maschine gewartet und teilüberholt. -Neue Schleifspindellagerung -Neue x-Achs Spindel -Obertisch überschliffen -Neue Geometrie Tischgeometrie Bedpfx Afevx Dvuj Escu -Neue Geometrie WSS zu Schleifspindeln B-Achse mit 1° Hirth Verzahnung Längspositionierung HF-Innenschleifspindel GAP Papierbandfilter

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Bcedpfxsv Dxxzo Af Esu Machine with heavy duty workhead. Machine will be partial overhauled before delivery. Machine will get a geometry protocoll according to the Kellenberger new machine guideline

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your o von Kürzlich gelieferten Maschinen mit zusätzlichen Optionen wie: -Spritzschutztüren -Kabine x-Achse -Schwenkwinkelanzeige Schleifspindelstock Geometrisch überholt und neu lackiert mit original Elektrik. Maschine hat Zentralschmierung und Rollenführung in der Flachbahn der x-Achse sowie Luftabhebung im Schleifspindelstock serienmäßig. -Digitalanzeige in 2 Achsen. Auflösung x-Achse 0,5my Optionen: -Drehgeber mit digitaler Anzeige im Werkstückspindelstock -Drehgeber mit digitaler Anzeige im Schleifspindelstock (keine Höhenverstellung mit Spindel möglich) -Neue stabile Innenschleifvorrichtung Durchmesser 80mm oder 100mm mit Höhenjustierung. -Erhöhung der Spitzenhöhe auf max. 225mm -Drehzahlregelung für die Schleifspindel Inklusive: -Bedienwerkzeug -Spannrohr für Futter Bedjuxftxjpfx Af Ejcu weiteres Zubehör auf Anfrage. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, Year of construction: 1982, grinding diameter 630 mm grinding length 600 mm centre height 320 mm Maschine wird überholt nach Kellenberger Messprotokoll und neu lackiert. Bedpfxsvq R Uzj Af Eecu Die anfällige Güttinger Steuerung wird durch die zeitgemäße BEMA X Steuerung ersetzt. Das heißt die Maschine erhält in diesem zuge auch eine komplett neue Elektrik. Siehe Beispielfotos. Maschine mit verstärktem Werkstückspindelstock zum fliegend Schleifen von schweren Werkstücken. Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg Bodov I Eq Sopfx Af Escu 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m Ready for delivery, with 12 month warranty in germany and neighbouring countries! Geometrically overhauled and repainted with new electrics. In KELLENBERGER quality!!! -Digital display in 2 axes. Resolution x-axis 0.5my -Modern workpiece headstock with cone MK5 -Modern tailstock with cone MK3 -Modern hydraulic unit -Paper belt filter Further accessories on request

Condition: used, Year of construction: 2010, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Control Fanuc 310is Completely machanically overhauled with grinding process and setup of one part. Original photo taken on the EMO 2010. Bcjdpfx Afevdk N Es Eju CNC control GE Fanuc 310is Hand panel for CNC control GE Fanuc Wenger loader optional Turned part with automatic indexing 1° Grinding head UR 1-2-3 Grinding wheel equipment left 500 x 80 mm Grinding wheel equipment right 400 x 63 mm Operating unit for one high-speed internal grinding spindle MFV / MFZ High-frequency internal grinding spindle MFN 1090 Coolant supply through the workpiece spindle Dressing unit on the upper table Swivelling holder for PCD diamond plates Basic module for KEL-TOUCH gate sensor and KEL-BALANCE balancing devices KEL-TOUCH lead sensor for universal grinding head variants R / RS / UR / URS KEL-TOUCH on the workpiece headstock for internal and external grinding Preparations for Movomatic ESZ 400 or Marposs P7 ME measuring controls Preparation for external filters Cooling lubricant switch-off for table devices Full casing emulsion Emulsion sanding mist extraction system Maintenance unit for additional pneumatic functions Preparation for KEL-VITA gantry loader KEL-POS, MOVOMATIC: C25 measuring probe Hydraulic preparation for arobo bezel

Condition: used, Year of construction: 2002, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm dimensions of the machine ca. 3,6/3,5 m Photos of identical machine with centre height 225mm Base: Kellenberger Kel-Varia UR175-1000 Kelco 120 Grinding head UR with T1-T2-T3 Basic equipment: -T1 500mm grinding disc diameter -T2 400mm grinding wheel diameter -Infinitely variable, high-resolution axis -Marposs measuring device for tool measurement -Active longitudinal positioning -GAP on T1 and T2 from ELASO contactless integrated in the control interface Semi-automatic balancing from ELASO integrated into the control interface -Tailstock with manual retraction -MK5 workpiece headstock with short taper DIN 55026 Belt-driven internal grinding device Options at an extra charge: - New high-precision workhead with torque drive - Internal grinding device for high-frequency spindles diameter 120mm -HF internal grinding spindle Fischer MFM-1224/42/31 D-21 -HF spindle with HSK holder 24,000 rpm with integrated GAP sensor. (delivery time) -CNC-controlled C-axis non-circular grinding -hydrostatic threaded spindle in x -new hydrostatic unit with only 1 pump and pressure accumulator thus better energy efficiency. -monitoring of the water content in the hydrostatic system -Suction system Bcodpsuxfucsfx Af Eeu Further options available on request Mechanical overhaul: -Complete machine overhauled according to Kellenberger measurement protocol -New service-friendly cab -repainting Electrical overhaul: -New modern CNC CIRCULAR GRINDING MACHINE control with BEMA rough grinding surface -New control cabinet -New drive technology -Replacement of all electrical cables Berus pressure switches etc. -New absolute glass scales in x and z -New absolute rotary encoder (for B-axis) Control system: The grinding software consists of a basic licence and various options that are possible depending depending on the equipment of the machine. Basic software - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal pendulum grinding - External and internal plunge-cut grinding - External and internal taper pendulum grinding - External and internal radius grinding, radius dressed on disc - Semi-automatic pendulum grinding - Workpiece zeroing - Grinding wheel zeroing - Measuring the dressing diamonds - 2 moulding diamonds - 1 shaped diamond or dressing roll (dressing roll required) - Moulding roller (dressing roller required) - 3 Flat dresser - Corrections - Z-position measurement (probe required) - GAP probing (grinding device required) OPTIONS at an extra charge: Software profile plunge-cut grinding: - External and internal profile plunge-cut grinding with profile disc Profile grinding software: - External and internal profile grinding with straight disc Software thread grinding: - Single and multi-start external and internal thread grinding with thread on the disc disc Dressing. Dressing of single and multi-groove discs. Flank angle freely selectable. Trapezoidal thread grinding software: - Additional dressing of trapezoidal threads possible External and internal non-circular plunge-cut grinding: - External and internal non-circular plunge-cut grinding Non-circular grinding software: A prerequisite for non-circular grinding is that the workpiece axis is equipped with a high-resolution rotary encoder so th...

Condition: used, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0-9,99 mm/Ø 0-9,99 mm/Ø ±8 ° longitudinal feed of the table 1100 mm table speeds 0,02-6 m/min 130 kg cross travel max. 270 mm 130 inkl. Spannung kg 80 mm tailstock quill taper MT 3 quill travel 30 mm total power requirement 6,5 kW weight of the machine ca. 3,05 t dimensions of the machine ca. 4 x 2 m Overhauled according to Kellenberger guidelines including new, modern and future-proof control system. Photo of already delivered machine in centre distance 1000mm. -Operation via the touch panel is extremely simple. -The symbols on the control panel are practically identical to the original original control system, so there is no need for familiarisation. -Diagnostic function with display of PLC messages and digital I/O -Dressing function can be extended or changed at the customer's request. -Orientated spindle stop of the workpiece spindle possible on request. -New maximum infeed of 40 mm can be extended on request. -Digital display in 2 axes. Resolution x-axis 0.5my Options: Bcsdpfx Afsuxfupe Esu -Encoder with digital display in the workpiece headstock -Rotary encoder with digital display in the grinding headstock (no height adjustment with spindle possible) with spindle possible) -New stable internal grinding device diameter 80mm or 100mm with height adjustment. -Increase of the centre height to max. 225mm -Speed control for the grinding spindle Included: -Operating tool -Clamping tube for chuck Further accessories on request. The x-axis of the machine has an electronically controlled infeed system with stepper motor drive. Hydraulic longitudinal and rapid traverse table movement. Versatile application in production for external cylindrical and internal internal grinding or for external, face and internal grinding in one clamping clamping of individual parts. Possible options: -Semi-automatic dressing cycles for external and internal grinding -automatic dressing compensation. -Measuring control

Condition: used, Year of construction: 2006, grinding diameter 350 mm grinding length 1000 mm centre height 175 mm Bcedpfx Aet Ii Nbef Esu weight of the machine ca. 3,5 t Machine completely overhauled with 12 months warranty Mechanically and optically like new Photos from the last overhauled machine with different options Fanuc 21i control -Grinding head UR 1-2-3 external/internal/plan -Axis automatic 1° Hirth serration -Active longitudinal positioning KEL-POS Movomatic -Semi-automatic balancing device KEL-BALANCE -Grinding wheel equipment left 400mm diameter -Grinding wheel equipment right 300mm diameter -Internal grinding unit with belt drive -Tailstock with micro-adjustment -fine adjustment upper table -Paper belt filter SBP4 240l

Condition: used, grinding diameter 250,350,450 mm grinding length 1000 mm centre height 125,175,225 mm grinding wheel diameter 400 mm grinding wheel width 50 mm bore 127 mm MK5 work piece spindle speed 20-400 U/min grinding head swivelling 360 ° grinding spindle head - swivable 180 + - ° grinding spindle speed 1500,1700,2200 U/min 0,001-0,030 mm/Ø 0-0,95 mm/Ø ±8 ° longitudinal feed of the table 1300 mm table speeds 0,02-6 m/min 130 kg 130 inkl. Spannugkg kg 70 mm total power requirement 6,5 kW weight of the machine ca. 2,5 t dimensions of the machine ca. 4,2 x 2,0 m As the world’s leading company in Kellenberger overhaul and retrofit we are not only able to deliver machines in a quality similar to a new machine and with warranty, but we can also offer you the service for your machines. Geometrically overhauled with new paint and original electrics. Foto of a 600U which we already have delivered. -Digital display in 2 axes. Resolution of x-Achse 0,5my Options: -Encoder with digital display in workpiece spindle head -Encoder with digital display in grinding spindle head (Height adjustment with spindle not possible) -New stable internal grinding diameter 80mm oder 100mm with height-adjustment. -Increase the center heigh to max. 225mm -Speed control of the grinding spindle Including:: -Adjustment tool -Draw tube for chucks other accessories on reqeust Die Werkzeugmaschine entspricht zum derzeitigen Zeitpunkt nicht den grundlegenden Sicherheits- und Schutzanforderungen wie in der BetrSichV 2015 Bcodet Ii Nuopfx Af Eju genannt. Eine Anhebung des erforderlichen Mindest-Schutzzieles ist mittels einer Gefährdungsbeurteilung nach BetrSichV zu ermitteln.

Condition: as good as new (ex-display), Year of construction: 2025, Offered is a CNC controled universal cylindrical grinding machine EMAG Weiss W 11 CNC. The machine is suitable for external-interna- face and cylindrical grinding. The W 11 CNC cylindrical grinding machine is perfect for one-offs- / prototype- and serial production. This cylindrical grinding machine is also used for sample production in the field of training and maintenance. CONTROL Eckelmann TECHNICAL DATA Workpiece length: max. 1.500 mm Center height: 200 mm | Option 320 mm Workpiece weight: 250 kg Workhead: MK 4 | Option MK5 / MK6 Tailstock: MK 4 TOOL CARRIER Bcodjr Ey Huepfx Af Esu Single wheel straight / incliend, but also possible 2 wheels on B-axis combined with internal grinding spindle. Price, delivery time and equipment of the machine according to agreement.

Condition: as good as new (ex-display), Year of construction: 2025, Offered is a External cylindrical grinding machine EMAG Weiss WPG 7 - external cylindrical grinding at the highest level and on the smallest footprint. Footprint of the WPG 7 is only 1,800 x 2,400 mm. The machine is perfect for machining small shafts or pinions. The WPG 7 can be loaded manually as well as by automated solutions (such as chain conveyors and linear gantry). CONTROL Fanuc 0i TECHNICAL DATA Workpiece length: max. 250 mm grinding Ø: max. 80 mm Center height: 100 mm Center length: 380 mm Workpiece weight: max. 30kg Grinding wheel Ø: max. 500x 80 mm Bedpfjtlrkbox Af Escu Price, delivery time and equipment of the machine according to agreement.

Condition: used, Year of construction: 1982, grinding diameter:250 mm grinding length:650 mm centre height:125 mm internal grinding spindle rev.-stepless:9500-50000 U/min workpiece speeds -stepless:50-10000 mm/min grinding head swivelling:90 Grad max. dia. of grinding wheel:400 mm spindle bore:30 mm grinding length - plunge feed:80 (100) mm max. grinding depth by internal grinding:ca. 170 mm max. bore diameter to be ground:90 mm Bcodpfx Afscxxube Eou feed speeds:240 mm/min max. workpiece weight:80 kg required cooling water:36 l/min centre distance:650 mm distance of workpiece spindle-taper cone:960 mm drive capacity - spindle motor:6,25 kW connected load:ca. 10 kW total power requirement:8,5 kW weight of the machine ca.:3,4 t dimensions of the machine ca.:3,9 x 2,5 x 1,85 m with Studer control, electric/hydraulic drive, variable speed, tailstock with fine adjustment and hydraulic back feed, work piece headstock with increased precision, table air , hydraulic removable dressing device, radius-dressing device, Hydro-Cyclone filter, automatic grinding wheel-balancing device, automatic dressing cycle with speed compensation

Condition: used, Year of construction: 1987, machine/vehicle number: 6004.01, grinding diameter:350 mm grinding length:1000 mm centre height:175 mm workpiece weight:120 kg Bcjdpfx Afsdmppqo Eju power capacity:5,5 kW turning speeds:max. 25000 U/min control:FMS 5-88 weight of the machine ca.:3,5 t precision grinding machine with SONY digital display, coolant system, electronic hand wheel, separate electrical cabinet, emergency cut-off

Condition: used, Year of construction: 2010, grinding length 1025 mm grinding width 520 mm Control SINUMERIK 840 D tool taper HSK-A 63 A - axis ° workpiece weight 30 kg distance grinding spindle - table min./max. 473,5 - 1023,5 mm x-axis 520 mm y-axis 550 mm z-axis 1000 mm V-axis 166 mm feed x-axis 4 - 6.000 mm/min feed y- axis 4 - 4.000 mm/min Feed z- axis 30 - 25.000 mm / min. table dimensions 1.400 x 874 mm Bcedpfx Afovxwine Eju spindle speeds (infinitely variable) 0 - 12.000 U/min power capacity - grinding motor 35,00 kW grinding wheel diam. min/max. 100 / 300 grinding wheel width 60 mm total power requirement 100,00 kW weight of the machine ca. 11,00 t dimensions of the machine ca. 8,60 x 7,25 x H3,80 m 5 Axis Profile grinding machine, with SIEMENS SIN840D, double dividing head (B-C axis), V-axis (coolant nozzles), EROWA tool changing device (machine can also be operated without a tool changer), fire extinguishing device, Renishaw probe prepared. Without Host-Computer for workpiece- tool-management. without coolant device - was connected to the central supply.

Condition: ready for operation (used), Weight: 2.2t, including documentation. Bedpfomqly Uex Af Ejcu

Year of construction: 1979, condition: refurbished (used), functionality: fully functional, TECHNICAL DETAILS Height of centers: 125 mm + heights of 50 mm distance between centers: 1.000 mm Grinding wheel ' diameter: 400 mm ' width: 50 mm ' Bore: 127.0 mm Bcedpfok H Hp Nex Af Eju angular displacement: 270 ° workpiece spindle head: 20 - 400 rpm taper of the spindle: 5 MT Taper in the tailstock: 3 MT table angular displacement: 8 ° Table speed: infinitely variable up to 6.0 m/min Internal grinding spindle with 60 000 rpm External grinding wheel motor: 4,0 kW Workpiece spindle motor: 1,5 kW Weight machine: 3.100 kg Overall machine dimensions: 2,860 × 1,680 × 1,670 mm (L × W × H) EQUIPMENT & SCOPE OF DELIVERY - Machine was completely retrofitted - New control cabinet & new wiring diagram - New motor & frequency converter for the working head - 2 axes DRO - Cooling tank with paper filtering - Geometry made according to the Kellenberger protocol - Internal grinding spindle - Many accessories Please refer to the attachment below for a test report on the machine.

Condition: new, JAINNHER Universal cylindrical grinding machine (SHU-321M / ШУ-321М) For sale is a JAINNHER SHU-321M / ШУ-321М universal cylindrical grinding machine. NEW condition . Surplus Inventory. Quantity discount available. If you are interested, please do not hesitate to contact us! APPLICATION Designed for precision grinding of external, end, conical and internal surfaces of high-precision cylindrical and cone-shaped parts. SPECIFICATIONS: Workpiece diameter Ø 0.025 – Ø 350 mm Distance between centers 750 mm Max. part weight (kg) Centers, 80 / In cartridge, 20 Wheelhead and feed Angle of rotation Deg. ± 15° Standard grinding wheel dimensions: OD x Width x ID, 405 x 32-50 x 152.4 mm Spindle speed rpm 1650/1850/2100 Longitudinal travel length 250 mm Feed handle One turn (diameter) 2 One division (diameter) 5 microns Headstock Spindle rotation Live/stationary center Angle of rotation Towards the operator 30°/From operator 90° Spindle speed rpm 6 speeds 50Hz: 50, 75, 100, 150, 200, 250 Central taper MK No. 4 / Quill taper MK No. 4 Through hole diameter mm 25/Tailstock Quill diameter mm 32 Table Rotation angle toward/away from operator 4°/9° Working distance One revolution 12.5 Feed mm/min. 50-4000 Attachment for internal spindle speed 20 000 rpm. Drive Drive KW (hp) 0.75 (1)/Headstock spindle KW (hp) 3.7 (5) Headstock spindle KW (hp) 0.4 (1/2) Spindle Lubricant Pump KW (hp) 0.1 (1/8)/Coolant pump kW (hp) 0.2 (1/4) Tank capacity Wheelhead spindle grease tank l (gallons) 24 (6) Hydraulic tank l (gallons) 60 (15)/Coolant tank l (gallons) 80 (20) DIMENSIONS: 3560 x 1520 x 1650 mm Net weight Approx. 2300 Kg Included equipment and accessories: Grinding wheels Wear parts kit (for 5000 hours of operation) Spare belts Set of fitter's and assembly tools (Box with tools) Diamond for dressing grinding wheels Spindle for internal grinding Set of mandrels for internal grinding. Bjdehwmhgspfx Af Ejcu Adapter flange for 3-jaw chuck 3-jaw chuck ø200 mm. Full list available after request for more information.

Year of construction: 1998, condition: good (used), CHEVALIER FSG 1640 AD SURFACE GRINDING MACHINE Bsdpfx Afsirfpgj Eecu MAKE CHEVALIER, MADE IN TAIWAN MODEL FSG-1640 AD YEAR 1998 TABLE SIZE 1000 x 400 mm GRINDING WHEEL SIZE 445 mm TRAVERSES 400 x 1000 mm MAX HEIGHT FROM TABLE TO SPINDLE CENTRE 445.0 mm TOTAL POWER REQUIRMENT 7.4 kW PLUS AUTOMATIC DOWN FEED WHEEL-MOUNTED WHEEL DRESSER SYSTEM HYDRAULIC MOVEMENT COOLANT SYSTEM 400.0 x 1000.0 mm ELECTRO MAGNETIC CHUCK MACHINE MANUALS

Condition: good (used), Year of construction: 2015, operating hours: 250 h, functionality: fully functional, For Sale: Guideway Grinding Machine (Retrofitted from Metal Planing Machine) We offer a robust guideway grinding machine, which has been professionally converted from an original metal planing machine. The main advantage lies in its relatively compact footprint in relation to the workpiece capacity. Technical Specifications: • External dimensions (LxWxH): 4,800 x 2,500 x 2,000 mm • Required floor space: 4,800 x 3,500 x 2,700 mm (+ control cabinet, coolant tank, access) • Table size: 2,000 x 800 mm • Distance between columns: 1,000 mm Bedpfxsxx Uudo Af Eocu • Travel paths (X/Y/Z): 2,000 / 1,000 / 600 mm Upgrades & Features: • New ball screw spindles and bearings • 2 new motors + 2 overhauled motors • 3 new frequency inverters • New Siemens SINUMERIK 802C baseline CNC system • Large grinding spindle: 2,840 rpm – refurbished + new motor • Small grinding spindle: 18,000 rpm – refurbished • Including control cabinet, coolant tank with pump, and separate, wall-mounted inverter for small spindle Inspection and trial run possible by appointment. Please contact us for more information.

Condition: excellent (used), Year of construction: 1988, operating hours: 1,000 h, functionality: limited functionality, machine/vehicle number: 99223, overall weight: 2,800 kg, Grinding Dia: min=0.8 to max 250 mm; Vertical stoke : 90 mm; Max. travel of the grinding head :300 mm Table size :320x600 mm; Max stroke of the table Tranversal 250 mm, Longitudinal 400 mm; Electric motor speed 80000 rpm, Pneumatic 180000 rpm. Dimensions 1585x1260x2665 mm, Weight: 2800 kg Bcodpexvccdefx Af Eeu

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, machine/vehicle number: MGB1320E, center height: 180 mm, workpiece weight (max.): 100 kg, grinding length: 500 mm, grinding wheel diameter: 400 mm, total width: 14,150 mm, total length: 18,000 mm, total height: 14,750 mm, grinding diameter: 320 mm, workpiece length between centers: 350 mm, grinding wheel width: 50 mm, spindle speed (max.): 3,000 rpm, feed length X-axis: 500 mm, feed length Z-axis: 150 mm, feed rate X-axis: 10 m/min, feed rate Z-axis: 1 m/min, overall weight: 2,100 kg, workpiece spindle speed (max.): 400 rpm, Equipment: rotational speed infinitely variable, Beijing Second Machine Tool Beijing Second Bcjdpfetr Azksx Af Eeu Semi-automatic High Speed Cylindrical Grinding Machine MBS1320E On-line production equipment; test machine available; roundness within 0.001 beier machine tool works co ltd Online production equipment machine testing available The roundness within 0.001