Used Tig Welding Machine for sale (66,509)

Condition: used, Spot and projection welding machine NIMAK type BMP 20/150 Spot welding machine, projection welding machine Mach. No. 81692 year of manufacture approx. 1980 Power at 50% duty cycle 150 kVA Clamping plate below 200 x 160 mm Clamping plate above 200 x 160 mm Power setting continuously variable Max. projection 150 mm Electrode force 200 - 2000 kp continuously variable Operating air pressure max. 6 bar Connection power 600 kVA Nwsdov Dxm Sjpfx Ac Eei Mains connection 380 volts, 50 Hz - Welding control DTW 4Z 2P - Single spots and series spots - Parallel electrode guidance - Water-cooled without cooling unit - Electric 2-hand control panel with emergency stop - Control cabinet with control permanently attached to the machine Space requirement L x W x H 1000 x 800 x 1800 mm Weight 900 kg good condition

Condition: used, AC spot welding machine, projection welding machine ARO Type MA 350 DC AC resistance welding machine Machine No. MA35031332 / 9731122B110 / Year of manufacture 1997 Power at 50% duty cycle 30 kVA Nwjdpfjhpf Iyex Ac Eji Power at 100% duty cycle 21 kVA Maximum welding power 156 kVA Reach 550 mm Electrode arm diameter 60 mm Electrode holder diameter 25 mm Cylinder stroke max. 80 mm Electrode force max. 730 daN (at 6 bar), continuously adjustable Operating air pressure 0.5 to 6 bar Mains connection 400 Volt, 50 Hz Connected power 75 kVA / 63 Amps / Conductor cross-section 3x 16 mm² Possible sheet metal combination max. 5 mm + 5 mm - Welding control ARO Micro 2X16 III Version 6Z2P Type 1B (6 times - 2 programs) - Continuously adjustable welding current via thyristor module - Parallel electrode guidance - Double-stroke welding cylinder (pre-stroke / welding stroke) - Operating mode: single stroke and series of spots - Electrode force continuously adjustable via air pressure - Water-cooled via external water cooling (water chiller not included) - Electric foot switch - Control cabinet with control unit permanently mounted on the machine - PC interface RS 485 - Welding point counter - Operating manual for control unit, spot welding machine and electrical diagram available Space requirement W x H x D 520 x 1550 x 1150 mm Weight 290 kg Very good condition

Condition: used, Spot welding machine, projection welding machine DALEX type PL 63 Serial No. N-0051390 Year of manufacture 2018 Output at 50% duty cycle: 63 kVA Output at 100% duty cycle: 44.5 kVA Maximum welding power: 182 kVA Rated welding current: 8.77 kA Throat depth: 250 - 550 mm Maximum arm spacing: 150 to (310 mm) Upper electrode arm diameter: 50 mm Lower electrode arm diameter: 60 mm Electrode holder diameter: 25 mm Electrode stroke max.: 65 mm Electrode force: 100 - 600 daN Operating air pressure: 1 to 6 bar Power supply: 400 Volt, 50 Hz Rated current: 158 A Connected load: 137 kVA - Thyristor power stage - Welding control HARMS+WENDE - HWH MPS 10β - 5-stage control, single spot, series spot, 8 programs - Electrode force infinitely adjustable via air pressure - Parallel electrode guidance - Single-stroke welding cylinder - Water-cooled via external water cooling system (recirculating water cooler not included) - Electric foot switch - Control cabinet with controller fixed to machine - Operating manual Nsdpfoycv Sasx Ac Eowi Required space (L x W x H): 1150 x 700 x 1600 mm Weight: 335 kg As-new condition

Condition: excellent (used), functionality: fully functional, Year of construction: 2017, laser type: fiber laser, laser source manufacturer: Rofin, laser source model: FL40, laser power: 4,000 W, laser wavelength: 1,070 nm, input voltage: 400 V, input current: 40 A, input frequency: 60 Hz, type of input current: three-phase, We offer this Rofin FL40 laser welding machine in very good condition, manufactured in 2017. Nominal power: 4000 W Power range: 10 - 100% Laser beam quality: 3 - 4 (Multi Mode 100 µm) mm·mrad Power stability: ±2% Pulse frequency range: CW - 5 kHz Wavelength: 1070 ±10 nm Maximum possible power (950-1100 nm): 8000 W Maximum possible power (1100-1150 nm): ≤100 W Supply voltage: 3 x 230/400 V ±10% or 3 x 277/480 V ±10% Mains frequency: 50 or 60 Hz Apparent power at the beginning of module life: 12.7 kVA Active power at the beginning of module life: 11.8 kW Current consumption at 400 V at the beginning of module life: 18.4 / CCU: +0.5 A Apparent power at the end of module life: 15.2 kVA Active power at the end of module life: 14.2 kW Current consumption at 400 V at the end of module life: 22 / CCU: +0.5 A Current consumption at 480 V at the end of module life: 18.3 / CCU: +0.5 A Njdpfjzcf T Tsx Ac Eswi Fuses: 40 A If you have any questions or need further information, please do not hesitate to send us a message or call us.

Year of construction: 1998, condition: good (used), functionality: fully functional, Edge milling machine, manufactured by IMAC year of construction 1998 . Model : CB 18 . Series : B20 Nwodpjzfwh Tjfx Ac Esi .

Year of construction: 1999, condition: excellent (used), working width: 620 mm, machine/vehicle number: SE 01510 A10, Heating Element Welding Machine HP60/40 by BRANSON The drive is hydraulic, supported by positioning and control systems. The machine is equipped with its own vacuum pump. Only a few operating hours (approx. 6,800 hours). Usable heating element area: width 600 mm x depth 400 mm Max. workpiece dimensions: - Max. width: 620 mm - Max. depth: 420 mm - Max. upper height: 350 mm Nsdpfx Aeykvdloc Eswi - Max. lower height: 350 mm (Combinations of part heights possible, depending on contour) - Max. processing temperature for contact method: 400°C The modular frame design allows for easy conversion and retrofitting. The side doors and the front door in the welding area can be easily opened (for rapid retooling). The automatic safety lift door ensures a high level of operator safety. The temperature control units on the operator panel have actual/target displays. The control device is a Siemens PLC HMI. The machine is controlled by a Siemens PLC (S7-300 controller). Heating elements are equipped with temperature sensors for temperature regulation and serve as safety cut-offs in case of overheating. The pin systems in the tool mounting surfaces ensure reproducible positioning. Advantages of heating element welding technology: - Reliable welding of workpieces with low or varying wall thicknesses. - Low scrap rate due to dimensionally accurate and repeatable welds. - Precise time, temperature, and force control enable welding of sensitive parts. - Virtually all thermoplastics can be welded with this process. - Different thermoplastic types can be joined (compatibility needs to be verified). Technical data of the machine: - Power supply: 3 x 400 V AC + N + PE - Power: 25 kVA - Rated current: 20 A - Required cable cross-section: 5 cables, each 6 mm² - Required pneumatic connection: 6 bar Machine dimensions: - Machine width: approx. 1.22 m - Machine width with operator panel: approx. 1.8 m - Machine depth: approx. 2.1 m - Machine depth with operator panel: approx. 2.6 m - Machine height: approx. 2.4 m - Machine height with raised safety door: approx. 2.85 m (open door) Machine weight: approx. 2.2 t

Condition: used, Technical details: plate thickness: 10 mm material thickness: 4,5 - 10 mm capacity in W: 2000 Watt voltage: 220 mit 4 Meter-Kabel V machine weight approx.: 18 kg dimensions of machine: L: 550 x B: 120 x H: 260 mm WELDING EDGE SHAPER - GRINDING MACHINE or PLATE SHAPER Hand tool Application: cutting and notching of plate-shaped workpieces Material thickness depends on material (max. 10mm) Tool = lower knife (die) and upper knife punch) optional with accessories As in the picture, for 200,00 Euro * Nsdju Ngfqjpfx Ac Eowi

Condition: used, Year of construction: 1960, Technical details: current capacity: 60 kVA throat: 680 mm arm distance: 115 / 415 mm pincer opening adjustable: 180 mm rated capacity: 60 kVA welding power: 71 kVA Nsdpfju Nv Emsx Ac Eowi electrode capacity: 100 bis 600 daN voltage: 380 V / 50 Hz V air pressure: min./max.: 6 / 10 bar cooling water consumption: 12 l/min weight of the machine approx.: 685 + 200 kg connection voltage: 380 V / 91 A V rated capacity: 60 kVA connected load: 54 kVA dimension L-W-H: ca. Maschine: 1.700 x 850 x 1.750 mm dimension L-W-H: ca. Aggregat: 900 x 650 x 1000 mm POINT WELDING MACHINE - WELDING TRANSFORMER Direct current three-phase welding machine Application: Spot, projection and series spot welding Maximum short-circuit power 89 kVA Primary short-circuit current 135 A Secondary current = short-circuit current: 25 kA and welding current max. 20 kA Electrode stroke max. 90 mm; electrode force min./max.: 100 daN / 600 daN Stroke sequence max. with 10 mm stroke 400 strokes/min. Spot fitting: electrode holder Ø 30 mm, adjustable 180 mm, arm distance = min./max.: 115 / 415 mm 2-fold foot switch Cooling unit, mobile = movable on wheels, connection power 1.45 kW, pipe connection R 3/4 inch, coolant R22 *

Condition: used, Year of construction: 2004, Technical details: table diameter: 400 mm table turning speeds: stufenlos U/min tilting range table plate: 90 ° voltage: 230 V / Hz V connected load: 11,8 kVA machine weight approx.: 220 + 173 kg POSITIONER - ROTARY TABLE with welding source Messer Griesheim Application: for circumferential seam welding Welding device: Welding rectifier Messer Griesheim Variomatic 40 for MIG-MAG, direct current; protection class IP 23; cooling type F Nodpfju Nkxhex Ac Eewi with remote control Stepless current/drain feed, 4.0 meter hose package Torch head Ground clamp/ground cable Size: L: 1.1 x W: 0.5 x H: 1.3 Weight approx. 279kg Welding turntable MB Milano, TGA 75: swiveling welding turntable up to 90° allows horizontal and vertical welding (direction of rotation left and right) Infinitely variable speed; operation via control panel and/or foot control stands on transport trolley Size: L: 0.8 x W: 0.6 x H: 1.3 Weight approx. 173kg Wire feeder type Eurotrac SLV, feed rate 1.2 - 18 m/min *

Condition: used, Technical details: current capacity: 100 kVA throat: 250 mm arm distance: ca. 400 mm current capacity: bei 50%=63 kVA total power requirement: 100 kVA weight of the machine approx.: ca. 600 kg Nwsdpsu Nwxbofx Ac Eei space requirements of the machine approx.: L:1,2xB:0,8xH:1,6 m Spot Welding Machine - capacity by 50% ED: 63kVA, secondary voltage 4,4-10,8 Volt - operational current by 10 % ED 26kA, secondary short circuit current 44kA equipment: - control over plant type E 0423.2 -eltros II from LEW Henningsdorf - foot control Machine not tested, on sale as is! i.D. *

Condition: used, throat depth: 420 mm, nominal power at 50% duty cycle: 60 kVA, input voltage: 400 V, type of cooling: water, nominal power (apparent): 14 kVA, Spot welding machine, type 8003 TECNA – for welding nuts and sheet metal – completely overhauled and inspected Rated voltage 400V Rated power 60 kVA at 50% duty cycle Short-circuit current 22 kA Welding current 17.6 kA Fuse rating 125A Outreach 420mm Electrode force 470 daN Cylinder with pre-stroke Total stroke 80mm Double stroke 60mm Nwjdpeh N Sd Uefx Ac Eji Electrode cone MK2 Welding control TE 180 with digital display of welding current, current rise, etc. Main switch on the control cabinet - new 2-stage foot switch according to UVV standards - all pneumatic and water hoses replaced - electrode holder new - original documentation / operating manual available - machine inspection with confirmation 07/2026 - weight approx. 330 kg Demonstration and inspection by appointment. Commissioning and training at the customer's site possible for an additional charge. The machine is located in Dresden, near the A17 highway. And we also always have a suitable cooling unit in stock – of course, for an additional charge ;-)

Condition: ready for operation (used), Resistance Welding Machine, Resistance Welder, Meritus RAS 150 VSH, Used Machine Manufacturer: Meritus Type: RAS150VSH, MPW-RW 811-1410 Overall dimensions: 900 x 1370 x 2450 mm Electrical data: 415 V; 150 kVA; 50 Hz Nsdpfordf Acsx Ac Eowi Equipped with light gate Tool water cooling

Year of construction: 2017, operating hours: 100 h, condition: excellent (used), functionality: fully functional, Equipment: CE marking, The SMRE machine is used for hot air welding of PVC fabrics and synthetic materials. The machine is in like-new condition and has been used very little. The working width is 800 cm. Nwsdpfx Ajzkqm Hec Eoi

Condition: excellent (used), Year of construction: 2004, Carl Cloos GLC 503 Quinto SD welding machine. A total of 4 units available. Year of manufacture: 2004-2004-1999. Price refers to 1 unit. Nedstkuk Ropfx Ac Ejwi

Condition: used, Year of construction: 2011, A well-preserved EMAG laser welding machine with EMAG ultrasonic testing system including Laser Rofin type: DC 060 built in 2009 Nedpfxeixxqke Ac Eewi Without exhaust unit The machine used to weld gears with coupling rings. Diameter 60-80 mm. Weld depth 4-6 mm. *

Condition: used, Year of construction: 1985, functionality: fully functional, machine/vehicle number: PS1/9173/9169/2, type of input current: three-phase, input voltage: 400 V, overall weight: 775 kg, electrical fuse: 105 A, compressed air connection: 5 bar, This Schlatter PS 130 is a robust, industrial spot welding machine renowned for its reliability in metal welding applications. Nwodpey Snycofx Ac Eji

Condition: new, The NEOMIG-i 500 G is a three-phase multiprocess welding machine with separate wire feeder. Its advanced digital technology and its duty cycle ensure excellent arc characteristics for industrial MIG/MAG applications. The integrated synergies facilitate setup and reduce spatter during welding. Equipped with the WF wire feeder, it offers a control precise welding parameters to ensure perfect quality. MULTI-PROCESS MIG/MAG : - steel and stainless steel wire: Ø 0.6 to 1.6 mm - aluminum wire : Ø 0.8 to 1.6 mm - CuSi and CuAl wire : Ø 0.8 to 1.6 mm - flux-cored wire (reverse polarity) : Ø 0.9 to 2.4 mm Nodpomxkdpjfx Ac Ejwi MMA DC / Pulsed : basic, rutile and cellulosic electrodes. TIG DC Lift / Pulsed. Gouging.

Condition: new, With digital technology, the NEOPULSE 400 CW is a three-phase pulsed MIG / MAG generator for heavy industry. Mobile and equipped with a cooling unit and a high-performance unwinding system, the NEOPULSE 400 CW is ideal for tackling the most demanding applications. Intuitive and functional, its digital interface makes it possible to act on the welding parameters with ease. MULTIPROCESS WELDING MIG/MAG : - steel and stainless steel wire: Ø 0.6 to 1.6 mm - aluminum wire : Ø 0.8 to 1.6 mm Nwodpfxsmxkggs Ac Esi - CuSi and CuAl wire : Ø 0.8 to 1.6 mm - Flux-cored wire: Ø 0.9 to 2.4 mm MMA DC / Pulsed: basic, rutile and cellulosic electrodes (up to Ø 6 mm). TIG DC CONTACT / PULSED. Gouging (up to Ø 6.5 mm).

Condition: used, Straightening and welding plate made of steel Machined steel plate from a tool frame Length: 2980 mm Width: 1380 mm Thickness: 74 mm - solid steel plate - milled surface Nwedpfjy N Du Rex Ac Eei - 4 rectangular cutouts - plate equipped with several symmetrical bores - 4 bolted towing brackets Net weight: 2175 kg

Condition: used, Spot Welding Machine DALEX Type SL 16 - 2 Machine No. ZZH/N-10183 Year of manufacture: approx. 2002 Nwjdpey N Duksfx Ac Esi Rated power at 50% duty cycle: 16 KVA Maximum welding power: 50 KVA Max. throat depth: 500 mm Max. electrode force: 17 - 278 daN Electrode arm Ø 45 mm Electrode holder Ø 25 mm Arm spacing: 150 mm / 300 mm Operating pressure: 1–6 bar Open circuit voltage: up to 3.6 Volt Connected load: 37 kVA Mains connection: 400 Volt, 50 Hz - Weld control MPS 200-003 - Welding cycle triggered via electric foot switch - Water-cooled Required space (L x W x H): 1100 x 720 x 1450 mm Weight: 230 kg Very good condition

Condition: excellent (used), functionality: fully functional, WMA WMP 08 Spot Welders in TOP Condition, The unit shows barely any signs of use and has only been operated very occasionally. Air-cooled one-handed spot welding unit for vehicle manufacturing, tank construction, steel cabinet fabrication, sheet metal processing, and the wire industry. - Trouble-free welding of all sheet metals - Galvanized sheets can be welded perfectly thanks to controlled current rise and fall - Air-cooled, equipped for external water cooling - Tools can be easily changed using standardized rotating connectors - Only one plug required for welding current, control cable, and water cooling - Always reproducible welding results thanks to built-in automatic energy control Microprocessor Thyristor Control - Constant current regulation - Continuous process monitoring - Simple and ergonomic operation - All set parameters and process values are visible at a glance - Changes to welding parameters allowed only for authorized personnel - Management of configuration and program settings possible via a central PC WMA WMS 108 Microprocessor Thyristor Control - 7 time settings - 8 program slots - Built-in controller - Automatic mains frequency detection 50/60 Hz - Power outage-proof parameter storage - 'with/without current' toggle at the press of a button Additional configuration parameters (locked for user): - Program selection - Advance contact - Advance contact time - Two-hand lock (check) - Locking start signal - Current flow control - Response threshold - Current flow monitoring - Monitoring time - Current flow control - Power factor adjustment - Delay first half wave External inputs (24V, DC stabilized and switching): - Thermal switch - Thyristor temperature - EMERGENCY STOP - Start 1 - Start 2* - Pressure contact - Program 1* - Program 2* - Pre-stroke ON - Program interruption after hold time (only force) - Two-hand lock (check)* * These functions can be activated or locked via configuration parameters. External outputs (24V, DC unstable ± 20%; + switching, max. 5 W): - Solenoid valve pre-stroke - Solenoid valve welding - Relay advance contact Njdpfjxrb Tgsx Ac Eswi - Relay ready for operation Dispatch via freight carrier possible upon prior arrangement. #8407

Condition: used, total power requirement:6,5 kW Nsdpocxxp Uofx Ac Eowi dimensions of the machine ca.:0,9 x 0,5 x 1,25 m

Condition: used, Year of construction: 1992, machine/vehicle number: 920544, current capacity:100 kVA throat:280 mm capacity at 50%:100 kVA pressure:1,1 t stroke:100 mm table-size:180 x 170 mm control:MPS-29-K-S-R total power requirement:279 kW weight of the machine ca.:1,3 t Nedpfxocxxwne Ac Eowi dimensions of the machine ca.:1,4 x 1,15 x 2,1 m spot-welding machine with Nimak micro-processor MPS-32-K control, water-cooled, opto-electronic safety curtain, emergency cut-off

Condition: ready for operation (used), functionality: fully functional, I am selling 1 to 6 complete sets here. Brand: Miller, Model: Proheat 35 – almost new. Njdpoyr Idtjfx Ac Eswi Food warmer with induction heating element, 400–460 V, CE marking. New price for a complete set: 54,000 euros. Sale only to businesses (B2B) + VAT, or net price for export. Errors and omissions excepted.

Condition: new, Year of construction: 2025, functionality: fully functional, machine/vehicle number: SWM001, type of input current: DC, nominal power at 50% duty cycle: 37 kVA, input voltage: 380 V, type of cooling: water, overall weight: 230 kg, warranty duration: 24 months, welding power (max.): 75 kVA, total width: 500 mm, total height: 1,620 mm, total length: 950 mm, Spot welder / welding machine with water cooling – 75KVA – adjustable power, resistance, etc., + spare tips Nsdpfxoyl Sy Ee Ac Eowi