Used Positioning Module for sale (13,341)

Condition: good (used), WSM Stationary Screwing Unit Assembly and testing of components for car radios and navigation systems. The assembly station is enclosed in a protective housing. The service doors are equipped with monitoring switches with interlocks. The doors are locked during automatic operation and can only be opened during automatic stop or manually after pressing the "Doors" button on the control panel. Automatic operation cannot be started with a door open. Dwjdpfx Acjibicho Ujb Operational Sequence The station is loaded with the pre-assembled component via the transfer belt. The following describes the operation steps of the automatic station with a transfer belt. In normal operation, all three stations operate in parallel. - Positioning the test unit (WT) with the pre-assembled module in station 2.1 - Lowering the carrier with the scanner and vision sensor - Scanning the 3 codes (front panel, front PCB, SD PCB), comparison with the database - Checking the correct locking of the FFC in the connector - Raising the carrier and lowering the test unit onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.2 - Positioning the screwdriver and screwing the front PCB in place - Lowering the test unit (WT) onto the conveyor belt - Positioning the test unit (WT) with the pre-assembled module in station 2.3 - Lowering the light shield and making contacts, adjusting the carrier with the test sensors from below - Type-dependent testing of the SD + CD slot lighting and buttons - Functional test of the CD eject button - Lowering the test unit (WT) onto the conveyor belt > continue If errors occur during testing, they are displayed on the screen. and can be repaired if possible. For this, the system is switched to manual operation and the doors are opened. After the repair and restarting the automatic system, the workpiece carrier is tested again in the station. If a repair is not possible (e.g., due to a screw error), the workpiece carrier is marked as NIO (Not Okay) in the control system and is not processed further. Manual NIO marking and rejection is also possible. Financing through our bank is also available. komplett-konzept.leasingo.de More assembly stations, new and used, can be found in our shop! International shipping costs on request!

Condition: excellent (used), Year of construction: 2012, LICON Type: LiFLEX 1477 1U Year of manufacture: 2012 Control system: Siemens SINUMERIK 840D Solution Line with integrated PLC control S7-300. Technical data of the machine Max. travel in X: 1400 mm Max. travel in Y: 700 mm Max. travel in Z: 700 mm A-axis swivel range: 45° to –225° B-axis: 360° Acceleration: max. 5 m/s² Travel speed: max. 60 m/min Technical availability: 96% Motor spindle speed: max. 16,000 rpm Motor spindle: HSK 63 Integrated spindle Spindle motor: 25 kW at 100% duty cycle Tool holder: HSK 63 Licon - Tool magazine DTC 30 2 disc magazines - total 60 positions. Positioning via servo motor Tool length from spindle center: max. 400 mm Tool diameter with full occupancy: max. 90 mm Tool diameter with free spaces on the right and left: max. 200 mm Tool weight: max. 15 kg Tilting moment (HSK plane): max. 15 Nm Tool change time: approx. 5.0 sec up to 15 kg Pallet changer with zero-point clamping system. Dwjdpfx Ajzi E A Hjc Uob Control system: - SINUMERIK 840D Solution Line with integrated PLC control S7-300. - PCU 50.3-C: Intel Celeron M Mobile processor 1.5 GHz / 512 Mbyte / 1 Mbyte L2 cache / 400 MHz - Connection of decentralized modules such as inputs/outputs, motor starters, interfaces is carried out via Profibus. - Operator panel front OP012 with 12.1" TFT color display, 800 x 600 pixels (SVGA), - Machine control panel MCP 483C - Siemens motors of type 1FK7 are used for the feed axes. - Spindles are designed as main spindle motors 1PH7, 1PM6 or asynchronous motors, depending on the application. Coolant supply: Technical data: Tank capacity: approx. 1500 l, Filter capacity: approx. 300 l/min for emulsion, 1x rinsing pump (centrifugal pump) 3 bar approx. 150 l/min, 1x HD screw spindle pump 30 bar, approx. 80 l/min. and minimum quantity lubrication (MQL). Voltage supply: 400V, 3 phases, 50/60Hz, TN-S with a reliable neutral conductor. Total connected load: approx. 106 kW. Dimensions, see layout plan. Transport dimensions, machine only, without auxiliary units: Approx. length 830 cm, width 360 cm, height 330 cm, weight 28000 kg.

Condition: like new (used), functionality: fully functional, Year of construction: 2024, control type: CNC control, degree of automation: automatic, controller manufacturer: KIMLA, laser type: fiber laser, laser source manufacturer: IPG, laser power: 6,000 W, sheet thickness (max.): 25 mm, sheet thickness steel (max.): 25 mm, sheet thickness stainless steel (max.): 14 mm, sheet thickness aluminum (max.): 12 mm, sheet thickness brass (max.): 12 mm, sheet thickness copper (max.): 12 mm, table length: 3,100 mm, table width: 1,600 mm, working length: 3,100 mm, working width: 1,600 mm, travel distance X-axis: 3,100 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 120 mm, cutting speed: 10,800 mm/min, type of cooling: water, overall weight: 10,000 kg, total length: 8,200 mm, total width: 2,800 mm, total height: 2,400 mm, Equipment: CE marking, cooling unit, documentation/manual, dust extraction, emergency stop, fume extraction, safety light barrier, * Dual automatic shuttle tables ensure continuous operation: while cutting on one pallet, the operator can load or unload the other. * Beam-shaping module for adjusting the laser beam profile. * The optical delivery fibre includes a safety circuit preventing operation with a damaged fibre or connector. * Automatic oxygen/nitrogen assist gas distribution with pressure control, low-pressure protection and real-time adjustment. * Compressed-air cutting capability. * Automatic cutting head height control with collision protection and nozzle height calibration. * Automatic sheet position detection aligns the toolpath with the sheet and supports automated loading. * X- and Y-axis linear motors with a 20 kHz control loop provide high dynamics on complex contours. * Dual-sided linear motor gantry drive enables high acceleration without loss of geometric accuracy. * Renishaw absolute position measurement ensures precise positioning, straight cut edges and gantry skew correction. * Monolithic, FEM-optimised frame with composite-concrete-filled chambers; no special foundations or anchoring required. * Linear guide and actuator mounting surfaces are machined in a single setup for high rigidity and accuracy. * Automatically locked front doors with laser-protection windows and protective glazing. * Integrated cooling unit with digital temperature stabilisation. * Steel slat-bed pallets with precision mechanical locking. * Servo-controlled chain-driven pallet changer; table changeover speed: 1 m/s. * Automatic diagnostics, diagnostic reports and free remote internet diagnostics after warranty. * Common DC Bus technology recovers braking energy and reduces power consumption. Dodpfx Acjzu Nm Hs Uowb * Integrated CAD, CAM, CNC nesting and control software with DXF/DWG editing, process selection and toolpath generation. * Software can be installed on additional workstations for offline cutting-plan preparation. * Ethernet connectivity enables integration with IT and production systems. * Parts, sheets and reusable remnants libraries support nesting on partially used sheets. * Project-specific process parameters can be adjusted without changing subsystem settings. * Automatic trim-cut generation for partially used sheets. * Multifunction control panel with keyboard, mouse, USB and gas-pressure controls. * Patented Dynamic Vector Analysis with real-time Ethernet drive communication. * Zoned fume extraction, pulse-cleaned dust collector and laser safety barriers around the pallet exchange area. * PC-CAM imports DXF/DWG files and automatically generates G-code, allowing job preparation at the machine. * Dynamic Vector Analysis maintains high speed on complex contours and shortens cutting times. * High-power-density linear motors provide high acceleration and dynamics. * The compact monolithic frame is welded and machined in a single setup for high rigidity and geometric accuracy. * The electrical cabinet is mounted above the machine, reducing its footprint. Side doors provide easy access to the cutting table.

Condition: used, HPLC Waters The system consists of the following modules and components: HPLC Waters Binary Solvent Manager HPLC Waters Auxiliary Solvent Manager HPLC Waters HDX Manager Dodpfx Aezg Tzxsc Uewb HPLC Waters Pal System HPLC Waters Leap Synapt HDMS Mass Spectrometer HPLC Waters Binary Solvent Manager Flow Control Modules Flow rate of 0.20 to 5.00 µl/min Solvents are mixed in the T-piece outlet of the flow control module. Auxiliary solvent manager Flow rates of 0.10 to 5.00 µl/min. Flow control module Flow rate of 0.20 to 5.00 µl/min Sample manager The sample manager injects the samples, which it draws from microtiter plates or vials, into the chromatographic flow stream. In maximum throughput mode, the sample manager can perform an injection in approximately 45 seconds, including a single standard wash, or it can do so in less than 60 seconds, including a double standard wash. The sample manager accepts plates with standard footprint, 5.03” x 3.365”, which correspond to SBS/ANSI-compliant plates (maximum height of 2.2 inches, including covers). The sample manager can store samples at any temperature between 4 and 40 °C (39 and 104 °F) under ambient conditions of 25 °C (77 °F) or less. Heating and capture module Inner diameter of up to 300 micrometers and a length of 250 mm Temperatures from 5 °C (9 °F) above ambient temperature to 65 °C (149 °F). The column base can be pivoted outwards into any position between 0° and 180°. In the 0° “home” position, the column base is located directly above the sample manager and can be connected to an optional optical detector. In the 180° “away” position, the analytical column can be connected to a mass spectrometer (on the right side of the system). The Synapt G2 is a Q-TOF-based mass spectrometer with an additional ion mobility cell, which enables orthogonal separation of the ions based on their shape and conformation. Equipped with an intermediate quadrupole (8k), this highly versatile instrument can be used not only for peptide identification (LC-MSE data-independent acquisition), but also for denaturation and native MS analysis. Documents & Downloads Data sheet: Operating manual Condition: used Scope of supply: (See image) (Changes and errors in the technical data, information are subject to change!) We would be happy to answer any further questions you may have by telephone.

Condition: good (used), CMC Q Cover Two LPA2 50-70 Hard Cover Maker The machine is in very good condition and ready for production. Made in Italy. Manufacturer’s description: The machine is very easy to set up, operate, and service. It can produce over 250 covers per hour. The machine is equipped with the following components: – a hot glue application module (laminator) with a roller steam extraction bar, – an assembly table with a vacuum system, – a module for folding the veneer edges in a single pass on both sides, – pressing rollers, – a module for positioning the cardboard, Veneer types that can be used: smooth and laminated paper, photo paper, canvas, artificial and genuine leather, etc. Technical specifications: Dwsdozw Tzgjpfx Ac Ujb Type: Semi-automatic machine for producing hardcovers Maximum cardboard format: 700 x 500 mm Maximum paper format (cover): 740 x 520 mm. Cardboard weight: 1.5-3.0 mm. Power consumption: 2 kW, Power supply: 380V. Adhesive type: hot or cold External dimensions: 140x210x125cm Weight: 490kg.

Condition: good (used), Bluhm Weber Legi-Air-4050S Labeling Machine 4.14.1 Basic Structure The system is designed as a closed aluminum profile frame and has a very compact design. The control cabinets are integrated into the lower part of the frame. The main valve manifold is located behind a service door below the control panel. The system includes four workstation stops. Operation is via a touchscreen. The control panel is mounted on the right side of the frame. A Bluhm Weber labeling system is used in the station; the Bluhm Weber documentation applies accordingly. 4.14.2 Operational Sequence - The incoming workpiece carriers with I/O modules are stopped, lifted (positioned), and contacted in substations 10.1 and 10.2. In these two stations, the I/O modules are automatically labeled. In substation 10.3, the I/O modules are automatically labeled. Label generation and content creation are automated, as is application to the devices. - After labeling is complete, the module is finalized in station 10.4. For this, it is stopped, lifted, and contacted. Following finalization, the workpiece carrier is automatically ejected from the station. Legi-Air 4050 RH Label Print and Apply System with Zebra ZE500-4 Print Module Motor-driven large roll unwinder Label rolls with a diameter of up to 430 mm and 900 linear meters of label web ensure long continuous production runs. Tandem operation ensures uninterrupted production. Applicator dies Quickly interchangeable applicator dies allow for the processing of label sizes ranging from small nameplates to DIN A5 EAN128 shipping labels. The Quick-Change option allows for format changes in seconds. Spring-loaded applicator dies compensate for uneven product surfaces, ensuring clean label application. Controller Bluhm Weber Standard Controller Zebra ZE500-4 Print Module Label Printer Standard Features • Print Methods: Thermal Transfer or Direct Thermal • Orientation: Right or Left • All-Metal Industrial Construction • 16 MB SDRAM, 64 MB Flash Memory • Applicator Interface • Transmissive and Reflective Media Sensors • Multi-Level Element Energy Equalizer™ (E3™) for High Print Quality • Real-Time Clock • Rotating Display • ZPL II™ – Universal Language for Zebra Printers Dwedpfxeibh Tks Ac Ujb Technical Specifications Maximum Print Width • 104 mm Media Specifications • Label and Carrier Width: 16 mm to 114 mm • Minimum Retraction Length: 13 mm • Minimum Non-Retraction Length: 6.5 mm • Minimum Stream Mode Length: 6.5 mm • Maximum Length: 990 mm • Maximum Continuous Media Length: 3810 mm mm • Ribbon width: 25.4 mm to 107 mm Resolution • 8 dots/mm (203 dpi) or 12 dots/mm (300 dpi) Maximum print speed • 305 mm per second (203 and 300 dpi) Technical specifications • Width: 245 mm • Depth: 379 mm • Height: 300 mm • Weight: 15.4 kg Financing through our bank is also available. komplett-konzept.leasingo.de Further assembly modules in other sizes – new and used – can be found in our shop! International shipping costs on request!

Condition: ready for operation (used), Year of construction: 2023, machine/vehicle number: 221/2-306, functionality: fully functional, operating hours: 207 h, type of input current: three-phase, travel distance X-axis: 3,200 mm, travel distance Y-axis: 920 mm, travel distance Z-axis: 70 mm, workpiece length (max.): 1,000 mm, number of axes: 3, number of slots in tool magazine: 4, total height: 2,500 mm, total length: 1,500 mm, total width: 2,500 mm, overall weight: 3,000 kg, Equipment: CE marking, documentation/manual, HOLZ-HER EVOLUTION 7402 4MAT – Vertical CNC Machining Center Year of manufacture: 2023 Operating hours: 207 h Availability: Immediately High-performance industrial vertical CNC machining center suitable for milling furniture carcasses and other components from wood and laminated panels. Key Features - Vertical machining with highly accurate vacuum positioning system (including complimentary vacuum pads) - Rear clamping for processing all edges of the workpiece, enabling complete machining without repositioning - Laser length measurement system - Air-conditioned control cabinet - Uninterruptible power supply for computer unit Technical Specifications - Working length: 200–3200 mm - Working height (Y): 70–920 mm - Panel thickness: 8–70 mm - Maximum speed: - Vector: 68 m/min - Per axis: X 25 – Y 60 – Z 20 m/min Machining Unit - 10.3 kW electrospindle (air-cooled) - HSK-F63 tool holder - 4-position tool magazine - XL boring unit – 19 drilling spindles (13 vertical, 6 horizontal) - Groove saw in Y-direction Software and Control - Complete CAMPUS V7 EVOLUTION CAD/CAM software - Included modules: NC-HOPS, aCADemy, MT-Manager, Workcenter, Scenes - Integrated 3D simulation Dwodpfxey Eygns Ac Uob - Intuitive programming and advanced machining management - Remote control console - USB port - Wifi Equipment - ECO vacuum system (8 m³/h)

Condition: used, Year of construction: 2017, Numerical Control with B-Solid Software - 3D CAD-CAM program to design, simulate, and manage processes of machining of Biesse machining centers and drilling machines BNest Software - Software module dedicated to processing in Nesting mode that allows you to create projects containing the list of articles with the quantities to be produced and the list of plates to be used with the aim of minimize the material used and processing times Working field in X axis mm 4300 Working range in Y axis mm 2200 N ° 2 work fields Nesting work plan Automatic loading system with side lift table Panel detachment system with 2 suction cups Dedst Ul Dnepfx Ac Ujwb N° 1 vertical 3-axis electrospindle, Kw 13.2, with automatic tool change, Hsk cone type Automatic tool change system with 16 positions - positioned on the rear of the machine BH 10 boring head with 10 spindles arranged as follows: - N ° 5 vertical in X axis - N° 5 verticals in Y axis Automatic unloading system with motorized belt Worktop cleaning system Printing and application system of adhesive labels with labeling machine, 22" monitor, keyboard and mouse with dedicated PC Protection and safety system with perimeter grids Safety system with bumper Automatic lubrication system Air conditioning system for cooling and cleaning the machine control N° 2 vacuum pumps 250 m3/h Installed power Kw 31

Condition: used, Year of construction: 2007, operating hours: 3,339 h, machine/vehicle number: LC615, Used ELOPAK sks-s60S shikoku filling lineTechnical Specifications & Performance DataThis aseptic gable-top carton filling machine is engineered for high-integrity beverage packaging, delivering reliable performance for long-life products. Manufactured by Shikoku Kakoki in 2007, it operates with low accumulated hours and supports multiple carton formats for flexible production planning in industrial packaging and beverage production environments.Manufacturer: Elopak Shikoku KakokiModel: SKS-S60SYear of manufacture: 2007Operating hours: 3339Filling mode: AsepticContainer type: Gable-top cartonsCompatible formats: 0.5L, 0.75L, 1.0LElectrical supply: 400 V, 50 Hz, 3-phaseCurrent draw: 114 ACompressed air pressure: 550–990 kPaAir consumption: 2460 NL/minAdvanced Automation & Control SystemsDesigned for aseptic operation, this machine supports precision filling in a controlled sterile environment. Its three-phase industrial electrical configuration ensures stable operation and straightforward integration with plant utilities. Format changeovers across 0.5L, 0.75L, and 1.0L cartons are engineered to be efficient, helping reduce downtime and improve overall equipment effectiveness in second hand or refurbished installations.Industrial-grade controls for consistent aseptic performanceProcess parameters optimized for sterile packaging operationsOperator-friendly interface for setup and monitoringInterlocked access points and safety circuits for protected operationProduction Line Integration CapabilitiesThis aseptic carton filler integrates seamlessly within a used bottling line or new packaging configuration. It is well-suited for pairing with upstream carton preparation or sterilization modules and downstream cap closing, date coding, case packing, and palletizing equipment. The machine supports inline or standalone operation depending on plant layout.Interfaces with conveyors and downstream packaging machineryFlexible line positioning for greenfield or retrofit projectsMulti-format capability for 0.5L, 0.75L, 1.0L cartonsMachine Condition & Maintenance HistoryWith only 3339 operating hours, this second hand aseptic filler presents low wear relative to typical lifecycle expectations for industrial packaging equipment. Its configuration and utilities align with common European plant standards, supporting rapid recommissioning by qualified technicians.Low operating hours indicating limited duty cycleWell-preserved aseptic configurationOperational Performance & VersatilityOptimized for aseptic beverage production, the machine is ideal for long-shelf-life products commonly packaged in gable-top cartons. Its multi-format capability enables agile product scheduling and SKU changes without extensive retooling.Aseptic filling for extended shelf lifeSupports standard gable... Dsdpfx Acoyz R E Tj Ujwb

Year of construction: 2013, condition: used, GEA Sour Cream Thermization Line Capacity: 1,500–2,000 l/h Year: 2013 Installed & Connected – Excellent Overall Condition Complete GEA Process Line We are offering a complete GEA Sour Cream Thermization Line originally designed for the thermal treatment of sour cream and fermented cream products. The line was installed in 2013 and remains installed and connected on site. It is available for inspection and can be offered complete with associated process equipment, automation, and technical documentation. The system was supplied as a complete GEA process line and includes a buffer tank, thermization skid, hot water circuit, CIP dosing system, pumps, valves, instrumentation, and fully automated process control. Main Application Originally designed for: • Sour Cream • Fermented Cream (25% fat) Potential Applications • Kefir • Cultured Buttermilk • Drinking Yogurt • Ayran • Cultured Dairy Beverages • Other fermented and viscous dairy products Process Capacity • Approx. 1,500–2,000 l/h Original Process Parameters • Product: Sour Cream / Fermented Cream (25% fat)• Maximum product viscosity: 230 cP • Feeding temperature: 15°C • Thermization temperature: 55–70°C • Outlet temperature: 20–50°C Scope of Supply 1. Sour Cream Buffer Tank 10,000 L Stainless Steel Insulated Tank • Approx. 10,000 litre capacity • Stainless steel construction • Insulated design • Agitator with 5.5 kW drive • CIP spray balls • Temperature and level instrumentation • Hygienic dairy execution • Complete with service platform and access ladder Manufacturer: • PRO-WAM Year: • 2013 2. GEA Thermization Skid GEA Ecoflex Plate Heat Exchanger System Complete thermization module including: • Regeneration section • Hot water heating section • Cooling section with ice water • Integrated hot water circuit • Stainless steel skid-mounted designMain features: • GEA Ecoflex plate heat exchanger • AISI 316 heat transfer plates • Maximum working pressure: 10 bar • Hygienic dairy construction • Fully integrated process control 3. Pumps & Process Equipment Product Pumps • Tuchenhagen TP centrifugal feed/CIP pump • Tuchenhagen VPSH positive displacement rotary lobe booster pump Process Equipment • Stainless steel process piping • Automated sanitary valves • Distribution valves • Butterfly valves • Temperature instrumentation • Pressure instrumentation • Auxiliary process equipment 4. Hot Water Circuit Complete hot water generation and control package including: • GEA Ecobraze brazed plate heat exchanger • Grundfos circulation pump • Samson steam control valve • Samson on/off valve • Spirax steam equipment • Expansion vessel with safety module • Temperature instrumentation• Pressure gauge 5. CIP Dosing System Integrated CIP dosing and cleaning section including: • Dosing pump • Suction lances with level sensors Dwedpfx Aszffzujc Uob • Distribution valves • Water shut-off valve • Water reducing valve Designed for automated cleaning and sanitization of the process line. 6. Automation & Control Fully automated process control system including: • Siemens S7-315 PLC • Siemens MP277 10" HMI touch panel • Profibus / Ethernet communication • Automatic thermization control • Automatic CIP control • Alarm management • Process parameter monitoring • Data recording functionality • Festo pneumatic valve island • Stainless steel control cabinets Automation Level • Fully automatic production operation • Fully automatic CIP operation ...

Year of construction: 2011, condition: used, THERMATOOL CFI 250 Solid State HF Welder 250 kW High frequency tube welding machine Dedezpx Iispfx Ac Uowb This THERMATOOL CFI 250 is a Solid State High Frequency Welder designed for the production of steel tubes and profiles using high-frequency welding technology. With an output power of 250 kW and a 400 kHz welding frequency, it delivers reliable, efficient, and high-quality welding performance for tube mill production lines. Technical Specifications · Manufacturer: THERMATOOL · Model: CFI 250 · Year: 2011 · Output Power: 250 kW · Welding frequency: 400 kHz · Input Voltage: 3 × 400 V · Input Current: 578 A Main Features · 250 kW MosFet HF inverter with 5 pairs of modules (5 positive & 5 negative) · AUTOMATCH automatic load matching system · 250Kw DC rectifier with PLC control Siemens S7 · Remote control console · Closed-loop distilled water cooling system Looking for a used THERMATOOL HF welder, 250 kW solid-state welder, or other second-hand tube mill equipment? Explore our extensive range of quality used machinery for the steel tube industry. Input Voltage: 3 × 400 V Input Current: 578 A Welding frequency: 400 kHz Output Power: 250 kW 250Kw MosFet HF Inverter with 5 pairs of modules: 5 positive & 5 negative 250Kw DC rectifier: with PLC control Siemens S7

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, machine/vehicle number: 2560460122, Tornos Swiss GT13/6 - Sliding Headstock Automatic Lathe CNC Control: FANUC 31i-B, 6 axes, 13 mm capacity Basic Machine Equipment: - 6 linear axes - Independent main and counter spindle - Synchronously rotating guide bush - Adaptation for operation without guide bush - C axis for main and counter spindle - Adjustable pneumatic ejector incl. counter spindle coolant flushing - 3-color signal lamp (yellow, red, green) - Centralized lubrication - Electrical interface for Tornos bar feeder - Oil mist extraction interface - Interface for fire protection system - Interface for customer M-function (6 inputs and 6 outputs) - Compliance with CE and EMC standards Main Spindle: - Max. speed: 15,000 rpm - Adapted for F16 collets (76-1076) - Max. bar diameter without preparation: 10 mm - Max. bar diameter with preparation: 13 mm - C1 axis function Guide Bush: - Max. speed: 15,000 rpm - Max. diameter of synchronously rotating guide bush: 13 mm (with integrated motor), guide bush type: B (853) - Max. workpiece length in one clamping: 180 mm - Adaptation kit for operation without guide bush (max. travel: 30 mm) Tool System for Main Operations: - Tool holder for 5 turning tools 12x12 mm on the front of the carrier - Tool holder for 4 turning tools 12x12 mm on the rear of the carrier - S11 tool drive (10,000 rpm) for rotating tools mounted on the front of the carrier X1/Y1 - 1 drive module for cross machining with 3 spindles for ESX 16 collets (2 x 10,000 rpm and 1 x 6,250 rpm) - S21 tool drive (6,000 rpm) for up to 2 driven units mounted on the rear of the carrier X1/Y1 (driven units not included) Dwodpfxoyzigce Ac Usb - Tool carrier with 4 bores Ø 22 mm for stationary finishing tools Counter Spindle: - Max. speed: 15,000 rpm - Adapted for F16 collets (76-1076), max. Ø capacity: 13 mm - C4 axis function Tool System for Secondary Operations: - Base carrier for 8 back-working tools; on the 4 upper positions, rotating and/or stationary tools can be mounted (rotating tools not included) - 4 lower positions with 4 fixed holders for ESX 16 collets - 2 stationary holders with Ø 22 mm bores (for upper positions) - S51 tool drive (6,000 rpm) for driving back-working tools (max. 4 rotating tools) ----- Attractive Offer – Flexible & Worry-Free We not only offer you a high-quality product, but also tailor-made financing options to suit your requirements. Whether down payment, installment plan, or individual financing solutions – together we will find the right option for you. Upon request, we will also handle the complete transport organization. From planning to reliable delivery, we ensure a smooth and punctual process so you do not have to worry about a thing.

Condition: used, Year of construction: 2026, operating hours: 10 h, functionality: fully functional, machine/vehicle number: 2026-078, working width: 1,600 mm, working height: 100 mm, warranty duration: 6 months, cutting width (max.): 1,600 mm, number of slots in tool magazine: 2, Used machine CNC cutter/plotter Cutting area in X and Y: 1,500 x 1,600 mm. Multifunctional CAM cutting system in CNC knife technology for 2D cutting of leather, fabric, technical textiles, foam and other flat, semi-flexible or rigid, non-metallic materials. Equipment of the used machine. • 1 cutting bridge and 1 Multifunctional tool head • max. material height 100 mm • Multifunctional tool head to hold 2 interchangeable tools • powerful vacuum blower for fixing the material • Standard equipped with gray conveyor table (Conveyor). Can be extended with other tools (on request): Dodpfswgc I Rjx Ac Uewb • EOT electric oscillating blade • POT pneumatic oscillating knife • PRT rotating blade • UCT universal blade • KCT Kiss-Cut tool • CTT creasing tool • V-Cut angle-cut cutting blade • Punching tool for pinches or holes • Printer mark detection • Camera registration • Milling Head + exhaust Easy-to-use function • Easy interchangeable cutting tools, "PLUG & CUT • Intuitive user interface • Easy blade change • Vacuum zones can be activated with a click Fast amortization • Low cost with high added value • Best material utilization through nest expert software modules (not included in equipment) • High velocity • Constant precision Data: • Short cutting times due to high positioning speed up to 90 m/min. • Repeatabiliy +/- 0.25 mm • Cuts single or multiple layers • Suitable for both single ply and multi ply or sheet goods and roll goods (can be extended with suitable unwinder) (Product photo as example) The machine is CE certified.

Condition: used, functionality: fully functional, Year of construction: 2020, table length: 2,270 mm, table width: 1,600 mm, working length: 2,270 mm, working width: 1,600 mm, travel distance X-axis: 2,270 mm, travel distance Y-axis: 1,600 mm, cutting speed: 60,000 mm/min, positioning accuracy: 0.005 mm, input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, type of cooling: water, total length: 3,990 mm, total width: 2,340 mm, total height: 1,600 mm, Equipment: cooling unit, dust extraction, fume extraction, We offer this used eurolaser LCS G3 XL-1600 laser cutting machine, year of manufacture 2020. System type: LCS G3 XL-1600 Serial number: 1308S8364P Year of manufacture: 2020 - Voltage: 400V/50Hz - Operating temperature: +10° to 32°C - Working area: 2,270 x 1,600 mm - Maximum material width: 2,350 mm, unlimited length - Cutting speed: 1–1000 mm/s - Axial acceleration up to 9.3 m/s² - Measuring system accuracy: 0.005 mm - Servo-controlled DC motors - Dimensions: 3990 x 2340 x 1600 mm - Hardware interface: RS 232C - Software: HPGL - LCD control panel - Two lenses – 5" and 7.5" - Laser Scout Connect (LS-CON) cutting software: Includes post-processor for laser system control and LaserScout PLANNER module for cutting time calculation. - Watchdog (E-WD): Monitoring and remote diagnostics of key system functions in real time. - LaserScout POSITION+ (LS-POS+): POSITION is a software package for working with a camera to recognize reference marks. The package also includes a camera and the Planner for cutting time calculation. - Cooling unit (CU-450): Water-to-air closed-loop cooling unit Dwedpfx Acjyu N H Ue Usb Ambient temperature: +10° to +32°C Voltage: 400V, 3~, 50Hz - Top extraction (EU-015-1): 1 x 1.5 kW vacuum motor Automatic voltage protection Voltage: 400V, 3~, 50Hz - Extraction unit (EU-030-2): 2 x 3.0 kW vacuum motors Automatic voltage protection Voltage: 400V, 3~, 50Hz - Raster cutting table (RP-XL32): Black anodized perforated table - PC, 21” monitor If you have any questions or need more information, please feel free to send us a message or call us.

Condition: excellent (used), Here, we offer you a 3DMICROMAC laser marking system. microCUT Enclosure Laser source IPG Raylase 3-axis scanning system Power measurement head 1 Power measurement head 2 Camera system for positioning Camera system for quality inspection Cooler Extraction system Control cabinet with IPCs Coolant distributor Machine dimensions: Machine weight: 2 tons Width 922 mm, Depth 4653 mm, Height 2925 mm Components: Extraction system: Height 2869 mm, Width 760 mm, Depth 1577 mm Cooler: Height 1697 mm, Width 1440 mm, Depth 860 mm Weight (without filling) 500 kg Laser rack: Height 1786 mm, Width 856 mm, Depth 806 mm Weight 500 kg Control cabinet: Height 2001 mm, Width 1616.05 mm, Depth 605 mm Dwedpfx Acszdqp Is Uob Machine connections: Electrical: Mains voltage 3*400 VAC/N/PE Mains current consumption 74A Frequency 50/60 Hz Power consumption 51.3 kW Control voltage 24/5 VDC Main fuse NH 100A gG Module: Laser source: Mains voltage 400 VAC Frequency 50/60 Hz, Power 16.7 kW, Current consumption 59A Cooler: Mains voltage 400V, Frequency 50/60Hz, Current consumption 40A Machine: Consumable media Operating pressure 6-10 bar Temperature 10-50 °C Quality ISO 8573-1 Solid particles: Class 1 Oil: Class 1 Water: Class 4 Residual oil content < 10µg/m³ Water content < 6 g/m³ Pressure dew point 3 °C Consumption < 120 l/min Cooling water cooling unit module: Cooling water outlet temperature 21°C Cooling water return temperature 26°C Set point tolerance 1K Cooling water flow rate 69 l/min Free pump pressure 1.5 bar DI water cooling unit Cooling water outlet temperature 26°C Cooling water return temperature 31°C Set point tolerance 1K Cooling water flow rate 10 l/min Free pump pressure 1.5 bar Laser source manufacturer IPG, Type: YLS-5000, Mode: Continuous wave, Quasi-continuous wave Wavelength 1070nm Power 5kW, Frequency 5 kHz Scanner manufacturer Raylase AG Type: Axialscan-30-Y Field size 1000x1000 mm Spot diameter 87 1/e²(µm) Resolution < 31 µm Working distance 1198 mm Cooling unit: Manufacturer Riedel Type: PC 250.01-NZ-DI-S Refrigerant R407C 50 Hz Net cooling capacity 38 kW 60 Hz Net cooling capacity 40.3 kW Camera system: Manufacturer e2V, Type: AVIIVA TM UM2 GE Quality cameras: Manufacturer e2v, Type: DiViiNA LM1 CL Extraction system: Manufacturer Donaldson Filtration, Type: DOWNFLO Oval 3-3 Max. Fan speed 3000 rpm Operating pressure: 4.2 bar Pulse duration 100ms Volume of the pressure vessel 92 l Type: Laser marking system microCUT Condition: used Scope of delivery: (See pictures) (Changes and errors in the technical data are subject to change!) We will be happy to answer any further questions you may have by telephone.

Condition: used, This is an Orthodyne 20 wire bonder, used for precision electronics assembly. The device is equipped with a microscope for detailed inspection during operation. These machines are often used for ultrasonic bonding in the semiconductor industry. The Orthodyne Model 20 is a manual ultrasonic heavy-wire wedge bonder primarily used for connecting power semiconductors (power devices), hybrid circuits, and power electronics with aluminum wire. Dsdpfx Acozi Ap Do Uswb Key specifications Property Specification Bonding method Ultrasonic wedge bonding Wire material Aluminum Wire diameter 4–20 mil (≈ 102–508 µm), depending on configuration Commonly used wire sizes 5 mil, 10 mil, 12 mil, and 20 mil Maximum bonding force Up to 1000 grams Ultrasonic power Up to 550 (machine setting) Working area Vacuum chuck with approx. 75 mm working diameter Operation Manual, under microscope Microscope Stereo zoom optics, typically 7×–40× depending on the model Applications IGBT and MOSFET modules Power hybrids DCB substrates Ceramic substrates (Al₂O₃, AlN) Thick aluminum bond wires for high currents Features Suitable for large aluminum wires up to 20 mil. Special Larrison bonding tools reduce wire damage and heel cracking. Automatic wire cutting during the second bond. Optionally available with deep-access clamps and a video camera for improved positioning.

Condition: good (used), Year of construction: 1995, functionality: fully functional, The perfect retrofit machine! Mechanically in phenomenal condition! This machine can be inspected under power until 12.05.2026 and will then be dismantled due to space constraints. Please refer to the attached KLINGELNBERG inspection reports available for download. Gleason P 800 Year of manufacture: 1995 Control: SIEMENS 840 C (discontinued) Condition: Mechanically in excellent condition Functionality: Fully operational Inspection: Available under power Technical Data: Nominal workpiece diameter: 800 mm Max. workpiece diameter: 800 mm Max. workpiece diameter, special version: 1,200 mm Nominal module: 20 / 30 mm Nominal module, special version: 25 / 35 mm Drive power: 35 kW Drive power, special version: 52 kW Cutter head speed range: 20 - 200 rpm Cutter head speed range, special version: 26 - 265 rpm Additional cutter head speed range, special version: 36 - 360 rpm Cutter head swivel range: +30 / -45 degrees Cutter head dimensions (standard cutter head), diameter/length: 350 / 375 mm Min./max. center distance workpiece/tool: 50 / 600 mm Center distance workpiece/tool, special version: 50 / 800 mm Max. axial slide travel: 700 mm Max. axial slide travel, special version: 1,000 mm Max. axial slide travel, special version: 1,300 mm Lowest cutter head position above table: 450 mm Table diameter: 800 mm Table bore diameter: 245 mm Table bore depth: 875 mm Max. table speed: 15 rpm Max. table load: 10,000 kg Machine dimensions: Dodpfx Acey Hfm Ne Ujwb Width A: 5,800 mm Length B: 6,900 mm Height C: 4,700 mm Machine weight: 22,000 kg Regarding the current KLINGELNBERG gear inspection data BEFORE grinding: "Pitch and lead are inconspicuous. One measurement shows a borderline or slightly out-of-tolerance fHα deviation in the profile. Please check whether this value is permissible according to the drawing/customer approval or if correction/rework is required. The gears were always forwarded for grinding to the RZ 1000 REISHAUER and processed accordingly. Nevertheless, overhaul of the C-axis is recommended. A cost estimate from GLEASON PFAUTER LUDWIGSBURG is available. Estimated cost: 10,000 EUR."

Condition: used, This listing includes 3 combination steam ovens, convection ovens from the manufacturer Convotherm, type OGS 20.20, gas-fired version without a boiler, manufactured in 2008. Offers for export in a package are preferred. Our ID Nos. 9361 + 9362 + 9363 The units are set for natural gas; they can also be converted to propane gas. The combination steam oven is equipped with a loading trolley for 20 x 2/1 GN containers or 40 x 1/1 GN containers and with insert racks for 2 x 1/1 GN containers. The units are sold in a package, without inspection and warranty, as returned by the customer. Inspection work will certainly need to be carried out for a new start-up. All 3 combination steam ovens are functional, and videos can be provided. The core temperature sensors are in good condition, and a door lock is included because one is no longer functional. Wiring diagrams and documentation are included. The units were exclusively used for heating/regenerating frozen ready meals. You will receive an invoice with VAT shown. Our used equipment service for you: High-quality branded equipment at fair prices Professional refurbishment/inspection & expert cleaning Tested & fully functional Flexible shipping or self-collection options Competent advice - before and after purchase Provision of operating instructions, connection diagrams & spare parts Testing according to DGUV V3 Technical data: W x D x H: approx. 1232 x 1055 x 1952 mm Power connection: V: 400 / kW: 2.2 Gas connection: kW: 70.0 Inserts: 20 x 2/1 GN or 40 x 1/1 GN Weight: approx. 403 kg Year of manufacture: 2008 Condition: Used, no inspection Further details: ACS Advanced Closed System (automatic energy-saving system, optimal humidity in the cooking chamber) Crisp & tasty (multi-stage cooking chamber dehumidification in ACS) Press & Go (symbol) for quick selection of defined cooking programs Tray Timer / staggered loading Start time preselection in real-time mode Night baking Delta-T cooking (multi-point core temperature sensor required) Cook & Hold Programmable with 250 cooking programs, each with up to 20 steps CONVOTHERM cookbook with pre-programmed cooking programs Disappearing door: more space and safety Dwedezvd H Dspfx Ac Uob Double-glazed door with integrated door locking position Antibacterial door handle with ventilation position and safety function Door handle with automatic closing function Motor brake when opening the cooking chamber door: less steam release Fan with autoreverse function Hand spray with infinitely adjustable settings Multi-point core temperature sensor Height-adjustable device feet Simple operation via menus/icons Bright graphic display Digital rocker switch for easy setting of temperature, time and core temperature Modular processor control with clear display and module self-test RS232 interface Storage of all device settings and cooking programs in an additional memory module Permanent self-diagnosis for error detection System with full-text error description Safety program mode: the device can be operated with limited functionality Basic prison version Robust design in stainless steel Seamlessly welded cooking chamber Rounded cooking chamber corners Suction plate easily removable Hygienic seal Cooking chamber lighting with shatterproof glass cover Including loading trolley with condensate collection tray Subject to change and errors. The sale is exclusively subject to our general terms and conditions.

Year of construction: 2017, condition: used, functionality: fully functional, machine/vehicle number: AU170124-01, APPLICATION AREA UP TO NOW: Positioning/handling of panels from L/W/H 1500mm x 1500mm x 12mm up to L/W/H 8000mm x 2500mm x 80mm EQUIPMENT: Traveling gantry with synchronized drive Dsdeytphijpfx Ac Uswb Vacuum lifter beam with automatically switchable suction rows, adjustable based on the respective workpiece length Schmalz vacuum generator with area suction grippers Clamp cartridges next to the suction cups ensure vacuum activation Z-lift of the suction spider via scissor guides Z-axis asynchronous motor, MoviDrive frequency converter, belt drive Interfaces for upstream and downstream stations Control system: Siemens S7-300 CONTROL CABINET: Power supply, power, and control section with main switch, power supply unit, motor protection switches, automatic circuit breakers, power contactors, auxiliary contactors, Simatic S7-300 control system consisting of a CPU315F-2PN/DP, PN/PN coupler, 1 pc. Micro Memory Card, Ethernet interface, all necessary digital input and output modules, and terminals, fully wired. Fieldbus system: Profinet-Safe.

Condition: used, This listing is for the Astoria Pacific Chemistry Analyser The unit is in full working condition and is ready for immediate use The Astoria-Pacific Chemistry Analyser is the standard single‑rack sampler module designed for the Astoria segmented flow analyser system—a precision instrument used in environmental, industrial, and research labs. Key Features Random‑Access XYZ Probe Moves in X, Y, and Z axes to target individual samples with a 12-place dedicated standards/calibrant rack Single Wash Station with Dedicated Pump Dwsdpjxhft Aofx Ac Usb Maintains probe cleanliness and avoids cross-contamination using an independently controlled wash reservoir and pump Supports Multiple Rack Types Compatible with both sample cups (2 or 4 mL) and test tubes (12–16 mm), and supports up to 102 total positions (90 samples + 12 standards)

Condition: used, Year of construction: 2011, Technical Specifications & Performance Data This 20,000 L aseptic tank is engineered for hygienic storage and buffering in beverage production and industrial packaging environments. It combines a newly manufactured pressure vessel with proven aseptic system heritage, making it a strong solution for second hand installations and used bottling line upgrades. Nominal capacity: 20000 L Design pressure: 0.09 to −0.1 MPa (positive pressure and full vacuum range) Pressure test pressure: 0.12 MPa Design temperature: 148 °C Main body material: S31603 stainless steel (food-grade corrosion resistance) Manufacturing year (tank body): 2025 Tank year: 2011 from Tetra Pak Dwsdpfxjx E Tbfj Ac Usb Engineering standard: GB/T 150-2024 (pressure vessels) System heritage: Tetra Pak aseptic module lineage for beverage applications Advanced Automation & Control Systems The tank is prepared for seamless integration into automated process control architectures typical of modern beverage production lines. Instrumentation ports and valve interfaces support level, pressure, and temperature monitoring, as well as aseptic steam-in-place (SIP) and clean-in-place (CIP) routines. The system documentation set includes activation and sequence diagrams and a communication description for S7-based control, supporting PLC/HMI connectivity, interlocks, and recipe-driven operation. PLC-ready signals for level, pressure/vacuum, and temperature Interfaces for aseptic valve clusters and CIP/SIP circuits Safety interlocks for pressure and vacuum protection Documentation for commissioning and parameterization Production Line Integration Capabilities Designed to function as an aseptic buffer or storage tank between thermal processing (e.g., UHT) and downstream filling. It can operate standalone or inline within a complete packaging line and is suitable for beverage production environments handling PET, glass, or carton filling operations. Format changes are minimal since storage capacity and process parameters are recipe-controlled. Inline integration with UHT, aseptic valve manifolds, and fillers Standalone operation for batch buffering and sterile hold Compatible with CIP/SIP plant utilities and sanitary piping Ideal for modernization of a second hand or used bottling line Machine Condition & Maintenance History The pressure vessel (tank body) is newly manufactured in 2025, paired with system documentation and aseptic process lineage originating from a 2011 Tetra Pak aseptic system. The unit is offered as second hand equipment and is ready for operation upon proper installation and commissioning. Availability of technical manuals supports maintenance planning, preventive routines, and efficient start-up. Body is new (2025) with documented pressure test and design ratings Provided with technical manuals, preventive maintenance references, and flow/layout documents Prepared for swift recommissioning in industrial packaging facilities Operational Performance & Versatility Engineered for hygienic and aseptic conditions, the tank provides stable pressure/vacuum capability for sterile storage.

Condition: ready for operation (used), Year of construction: 2020, overall weight: 1,080 kg, total width: 1,960 mm, total height: 1,500 mm, table length: 3,020 mm, table width: 1,520 mm, travel distance X-axis: 3,020 mm, product length (max.): 3,560 mm, table load: 400 kg, number of axes: 2, Plasma cutting machine manufactured in 2020. This PLASMACUT 3015T features a cutting area of 3,020 × 1,520 mm and a maximum plate thickness of 50 mm. It includes a robust gantry drive system and operates with a Hypertherm Powermax 105 Sync plasma power source. If you are looking to get high-quality plasma cutting capabilities, consider the PLASMACUT 3015T machine we have for sale. Contact us for further details regarding this machine. • Cutting Area: 3,020 × 1,520 mm • Operating Voltage: 230 V • Phase: 1 Ph • Power Consumption: 300 VA • Maximum Table Load: 400 kg • Maximum Plate Thickness: 50 mm • X-Axis Guide System: Hardened Precision Round Steel Guides with Adjustable Rollers • Y-Axis Guide System: Profile Rail Guides Dwedpfxezrnwxo Ac Ujb • X-Axis Drive: Reinforced Timing Belt (5M15) • Y-Axis Drive: Reinforced Timing Belt (2 × 8MR30) • Gantry Drive: Dual-Sided Drive with Rigid Coupling Shaft • Positioning Speed: 24 m/min • Repeatability: Better than 0.1 mm • Control Software: CNC-Workbench Plasma • CAD/CAM Software: CNC-Workbench Plasma • File Format Support: DXF • Plasma Power Source: Hypertherm Powermax 105 Sync • Plasma Power Source Voltage: 400 V • Maximum Cutting Current: 105 A • Piercing Capacity: 22 mm • Maximum Severance Capacity: 44 mm • Duty Cycle at Full Load: 80% • Process Gases: Air, Nitrogen • Manual Torch Connection: Optional • Water Tank Capacity: Approx. 300 L • Exhaust Connection Preparation: DN 150 mm • Portal Clearance: 300 mm • Laser Pointer: Yes • Torch Height Control (THC): Automatic Arc Voltage Control • Operating System Requirement: Windows XP / 7 / 8.1 (PC Not Included) Additional Equipment • Water Tank • Rittal Operator Panel • PC with Installed Control Software • Hand Control Unit • Operating Manual • Serial Connection Cable • Consumables Kit • Hypertherm Powermax 105 Sync Plasma Power Source • Automatic Nesting Module (License for One PC) • Laser Alignment • Scribing Option • Fume Extraction Bridge Preparation (DN 150 mm) • Portal Height Extension to 300 mm Clearance

Year of construction: 2016, condition: like new (used), Renishaw Roughness measuring kit for REVO incl. - SFP1 Modul Dwjdjni Arnspfx Ac Usb - SFS1 Probe straight - SFS2 Probe cranked - SFA roughness standard - SFCP positioning device for SFP1 - RCP TC-2 modul changer

Condition: ready for operation (used), Year of construction: 2022, operating hours: 1,197 h, controller manufacturer: SIEMENS, controller model: SINUMERIK 840D SL, laser power: 6,000 W, travel distance X-axis: 3,100 mm, travel distance Y-axis: 1,525 mm, number of axes: 3, This 3-axis HGTECH Marvel 6000-3015 fiber laser cutting machine was manufactured in 2022. It features a working area of 3000 x 1500 mm. The machine is equipped with a Siemens SINUMERIK 840D SL CNC control and an automatic pallet changer for enhanced productivity. If you are looking to get high-quality cutting capabilities, consider the HGTECH Marvel 6000-3015 machine we have for sale. Contact us for further details. • Working area: 3000 x 1500 mm Dwjdpoy Egwajfx Ac Ueb • Drive system: gantry drive • Transmission: rack and pinion • Control panel: touch color display • Motors and drives: Siemens motors and drive modules • Cutting head: Precitec ProCutter (compact/lightweight, autofocus focusing lens, distance sensor) • Laser source: external solid-state fiber laser Raycus • Laser output: single fiber (one LLK output) • Positioning: laser diode • Sheet detection: outer edge detection • Nozzle cleaning: automatic • Workspace lighting: integrated • Status indication: machine status light • Waste system: roll-out drawers, right side • Electrical cabinet: with internal lighting • Electrical connection: 380 V, 3‑phase, 50 Hz, 100 A Additional equipment • Cooling system: chiller unit • Pallet system: automatic pallet changer (longitudinal) • Extraction system: multi-chamber extractionNote: Laser power appears twice with different values (4000 W and 6000 W). Please confirm the correct rating.

Condition: excellent (used), Year of construction: 2017, operating hours: 100 h, functionality: fully functional, overall weight: 300 kg, Tray-Loader TL-6040 - 2-lane stack-on module for the economical transport of trays (boxes) for printed circuit boards. The empty trays are removed from the transport carriage, automatically positioned and made available for assembly. After placement, the trays are automatically destacked on a 2nd transport trolley. - Compact design - Small floor space - Stacking module - Transport trolley - Standard tray size: 400 x 600 mm - Sturdy welded steel frame - W x D x H: 840 x 1,330 x 1,870 mm - Manual operating height: 930 - 1,050 mm Dsdpsunh I Njfx Ac Ujwb - Compressed air 0.6 mPa (6bar), oil-free, filtered, dry - Average consumption approx. 10l/min - Ambient temperature +18°C - + 30°C - Weight approx. 300 kg