Used Hydraulic Press Brake for sale (36,175)

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Laodpfx Asu D Tz Usn Ueb Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Single-column hydraulic press MAE type S63SZ SO . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Lodpfx Anjdzp Trs Ueab Ram stroke: 500 mm Max. installation height: approx. 730 mm Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Lasdpfxjhmmfko An Uob Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: used, Single-column hydraulic press with draw cushion RÖCHER Type REP 100.01 SZ Hydraulic deep-drawing press Machine No. 15.499 Year of manufacture 2003 Pressing force: 100 tons Ram stroke: 500 mm Throat depth: 370 mm Installation height: 600 mm Lodpfx Ansyupulj Ueab Table surface: 850 x 700 mm with a drop-through hole Ø 150 mm Ram surface: 700 x 600 mm Ram ejector force: 16 tons (160 kN) Ram ejector stroke: 100 mm Ram ejector with internal thread M24 x 1.5 mm Draw cushion force: 40 tons (400 kN) Draw cushion stroke: 200 mm Draw cushion area: 530 x 530 mm Pressure holding time: 0 to 90 sec. Table height above floor: 910 mm Hydraulic operating pressure: max. 300 bar Hydraulic tank capacity: 700 liters Approach speed (rapid traverse): approx. 400 mm/sec. Pressing speed up to 23.8 tons (238 kN): 5 to 68 mm/sec. Pressing speed up to 100 tons (1000 kN): 5 to 16 mm/sec. Return speed: 50 to 400 mm/sec. Main pump drive power: 18.5 kW Auxiliary pump drive power: 4 kW Power supply: 400 Volt, 50 Hz (63 Amps) - Operation and programming via PC 670 touch panel, keyboard and mouse - Machine control via SIEMENS S7-300 PLC system - Ram stroke and press force programmable via control system - Draw cushion with drawing and ejector function - Draw cushion force infinitely adjustable - Ram and draw cushion equipped with direct linear measurement system - Draw cushion can be moved in and out under the press area, for punching work using the drop-through hole - Floor-level installation, draw cushion does not penetrate the floor - Pressure and stroke cutoff - Fixed stop with indirect measurement system - Pressure holding time infinitely programmable - Table with holes for the draw cushion ram rods - Ram with ejector - Knock-out damping - Stroke triggering via two-hand operation, foot switch, hand lever and push button on the control panel - LEUZE light barrier as reach-in protection for safety operation - Front mirror columns on the press table can be shifted laterally - Electrical control cabinet mounted on machine frame - Hydraulic oil cooler with fan motor (oil-air cooling) - Manual central lubrication pump - 2x hose connections for tool tempering or cooling at the ram - Piece counter in the control system - 306 read operating hours - Operating manual, hydraulic diagram, and electrical diagram available Space requirements (L x W x H): 3100 x 1800 x 4160 mm Weight: approx. 13 tons Very good condition, as new

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Lsdpfx Aswva I Hon Ueab Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, High-performance baler MACFAB - BEMA type 650A Hydraulic press for packaging waste, recyclable renewable raw materials, secondary raw materials Manufacturer no. MF J0162 Year of manufacture 2021 Pressing force 50 tons. Press plate stroke approx. 1000 mm Cycle time per stroke approx. 40 sec. Pressing chamber floor area 1500 x 1100 mm Pressing chamber height 1650 mm Filling opening 1500 x 870 mm Filling height approx. 1250 mm Laedpfx Asvq Rtkon Uob Bale format 1500 x 1100 mm Bale height max. 1100 mm Hydraulic operating pressure 200 bar Motor power 5.5 kW Mains connection 400 volts, 50 Hz, 12 amps. - with two hydraulic cylinders - Door locking via threaded spindle with handwheel - Pressing operation only with the pressing chamber door closed - 2-hand operation for hydraulic tipping of the finished pressed bale - Free space for manual strapping - Standard industrial bales of 1500 x 1100 x 1100 mm are produced - the highly compressed bale is automatically tipped onto a pallet - only 62 operating hours Space requirement L x W x H 2120 x 1350 x 3220 mm Height for transport with lowered hydraulic cylinders approx. 260 cm Weight 1.8 ton. The machine is in very good condition, as good as new. The press has a new price of EUR 22,200 net at BEMA The BEMA company also buys the packaging waste that you press into bales with this press.

Condition: used, Hydraulic notching machine with adjustable angle SIMASV model AV 220-6PA Serial no.: C1524 Year of manufacture: 1996 Blade length: 220 mm Material thickness (steel): 6 mm Material thickness (stainless steel): 4 mm Table dimensions: 950 x 790 mm Table height: 940 mm Motor power: 3 kW Power supply: 400 Volt, 50 Hz - Operation via push-button or foot switch - Adjustable notching angle from 30° to 140° - Angle adjustment via 2 handwheels (right and left) - Hydraulic clamping for the adjustable blades - Electric foot switch - 2 adjustable stop rails with angle scale Ledpfx Ajrzfh Hjn Uoab - Multiple millimeter scales integrated into the table top - HSS blades newly ground, as new Required space (L x W x H): 1000 x 950 x 1470 mm Weight: 750 kg Very good condition

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 Laodedzp Tcopfx An Ueb make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Year of construction: 1992, Press brake Manufacturer: Beyeler Type: Euro III 60x2050 Year of manufacture: 1992 Bending force: 60 tons Bending width: 2,050 mm Rated current: 16 A Ljdpsyni H Usfx An Usab Machine weight: approx. 4,600 kg Equipment Extensive range of tools Various upper and lower tool sets Operational and immediately ready for use Machine is fully functional ä19526

Condition: used, Year of construction: 1991, Press brake Manufacturer: AMADA PROMECAM Type: HFB 125/40 Year of manufacture: 1991 Control: DELEM DA 58 Maximum pressing force: 1,250 kg Maximum stroke: 180 mm Sheet thickness: 8 mm Working width/Throat: 3.7 m Number of phases: 3 Power consumption: 11 kW Voltage/Frequency: 380/50 Rated current: 24 Weight: 9,900 kg ä19526 Availability: immediate Ljdpfox Tzl Ijx An Usab

Condition: good (used), Year of construction: 2018, CNC press brake Manufacturer: SMD Yawei Type: PBB-630/6200 Year of manufacture: 2018 Ledpfx Aorivu Ssn Usab CNC control: CYBELEC ModEva 15 Press force: 6,300 kN Working width: approx. 6,200 mm DSP-Laser-TX Connection power: 400 V / 95 kVA 19526

Condition: used, Year of construction: 2022, Bystronic Xpress 80/2100 Hydraulic Press Brake. S/No. Xpress 22334EU (10/2022), Max Press Force 800KN, Max Working Length 2100mm, Max Stroke 200mm, Machine Weight 6000kg Ledpfsy D Rbasx An Ueab Location: These lots are located in Yeovil, UK. Please Note: There are no loading facilities on site, dismantling and loading will be at the cost of the purchaser.

Condition: used, Year of construction: 1986, functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, pressing force: 204 t, stroke length: 220 mm, table length: 4,000 mm, clearance between the columns: 3,400 mm, overall weight: 12,000 kg, We offer this used PROMECAM Amada STPC 204 200 40 160 press brake, manufactured in 1986. Machine number: STPC 200 40 160 Maximum pressing force: 2,040 kN Maximum stroke: 220 mm Voltage: 380 V Frequency: 50 Hz Date of manufacture: 20.10.86 Bending length: 4 m Distance between uprights: 3.4 m Includes tooling! Machine weight: approx. 12 tons Equipped with CYBELEC DNC 7000 control A crane is available for loading. The machine is functional and still in use / can be tested while powered on. However, due to its age, we cannot offer any warranty. If you have any questions or require further information, please feel free to send us a message or call us. Laodpfey Tmlasx An Ueb

Year of construction: 2010, condition: used, machine/vehicle number: B0605A0061, Control system: TRUMPF CNC, X-axis: approx. 500 cm, pressing force: 400 t, working length: 5,050 mm, weight: 34,000 kg. Ledpfoy T Nytjx An Usab

Condition: used, Year of construction: 2008, machine/vehicle number: B0505A0232, operating hours: 22,320 h, (Hydraulic system activated), manufacturing number: F1028-F, pressing force: max. 170 t, stroke: max. 445 mm, operating pressure: max. 300 bar, weight: 12,200 kg, control system: TRUMPF CNC, X-axis: 3,000 mm, angle sensor. Laedpfoy T Nyysx An Uob

Condition: excellent (used), Year of construction: 2004, Technical specifications: Working length: 2600 mm Width between columns: 2150 mm Pressing force: 45 tons CNC control: DELEM DA 66 W Controlled axes: Y1/Y2; X; R; Z1/Z2 Lasdpfx Ajwd Uinsn Usb Motorized adjustable backgauge with 4 stop fingers Thrust: 310 mm Working height: 930 mm Motor power: 5.5 kW CE mark Dimensions (length x width x height): approx. 3000 x 2150 x 2150 mm Weight: approx. 5 tons Accessories: 1 set of standard tools Condition: The machine is in very good condition. The seller is not liable for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: good (used), Year of construction: 2008, functionality: fully functional, Full-option used 3-meter press brake Type: E Brake 150 3100 Capacity: 3100 x 150 tons E-Control (new original Safan CNC!) 8-axis CNC (Y1, Y2, X1, X2, R1, R2, Z1, and Z2) Hydraulic upper and lower clamping Year of manufacture: 2008 Preparation for bending aid 1 set of tools included. Ledpeyw Suhsfx An Ueab 2 machines available

Condition: like new (used), Year of construction: 2026, pressing force: 20 t, For sale is a C-frame assembly and small-series production press from the manufacturer DURENDUS with a maximum pressing force of 20 tons. The machine has a table size of 700 × 920 mm, a maximum installation height of 550 mm, and a stroke of 400 mm, making it suitable for assembly work, small-series production, pressing operations, and straightening processes in industrial applications. ##### Technical data + information: C-frame assembly and small-series production press – 20 tons – 700 × 920 mm ==== General information - Design: C-frame / single-column press - Manufacturer: DURENDUS - Pressing force: 5–20 tons (adjustable) - Maximum installation height: 550 mm - Table size: 700 × 920 mm - Press head: Ø 100 mm - Table height above the ground: 1,000 mm - Overall dimensions (W x D x H): 900 × 900 × 2,340 mm - Total weight: approx. 1,200 kg - T-slots: DIN 650 – 22 mm or according to customer requirements - Forklift pockets: available - Press area lighting: available ==== Hydraulic cylinder - Stroke: 0–400 mm (adjustable) - Cylinder diameter: Ø 110 mm - Piston rod diameter: Ø 65 mm - Maximum working pressure: 280 bar - Return speed: 50 mm/s - Working speed: 10 mm/s - Idle speed: 10 mm/s - Pressure build-up time: max. 2 sec. (steel on steel) ==== Hydraulics & drive - Hydraulic pump: ASC - Delivery rate: 24 l/min - Motor power: 3 kW - Pressure accuracy: ±5 bar - Tank volume: 60 l - Valve technology: DUPLOMATIC - Filter technology: FILTREC - Oil level monitoring: electronic - Cooling: oil-air cooling - Hydraulic unit: mounted at the top rear Lsdpfoy Sx Uwsx An Ujab ==== Control system - Operation: foot pedal or hand lever - Pressure setting: via rotary control - Stroke limitation: via adjustable sensors - Selector switch: foot / hand operation - Switch cabinet components: mostly SIEMENS ==== Safety - Emergency stop switch - Stroke limitation - Stable steel construction - CE-compliant design ==== Electrical connection - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Main motor connection power: 3 kW - Total connection power: max. 5 kW ##### Application areas: Assembly work, small-series production, pressing, straightening, toolmaking, fixture construction, metalworking, maintenance, workshop operations, service applications (Hydraulic press, C-frame press, single-column press, assembly press, small-series production press, workshop press, 20-ton press, pressing press, straightening press, industrial press, C-frame press) Are you looking for a hydraulic press tailored to your specific application? Contact us for an individual offer. Our hydraulic presses are manufactured according to German Machinery Directives and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they meet all aspects of the national Brazilian safety regulation NR 12, which is based on these. Our strength lies in the design and construction of special machines and press automation. We distribute customized hydraulic presses at surprisingly affordable prices. The hydraulics of the presses predominantly use components from leading European manufacturers.

Condition: reconditioned (used), functionality: fully functional, stroke length: 105 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table height: 970 mm, throat depth: 200 mm, total length: 1,420 mm, total width: 1,100 mm, total height: 1,800 mm, overall weight: 2,800 kg, working width: 60 mm, back gauge: 345 mm, control type: manual, actuation type: hydraulic, Press Brake Brand: PROMECAM Model: PPH25.12B Ledpoxwukcsfx An Ueab Capacity: 1200 x 25T Distance between uprights: 1020 mm Throat depth: 200 mm

Condition: good (used), functionality: fully functional, Press Brake Brand: AMADA Model: HFT 80/25 Capacity: 2500 x 80T 4 axes Distance between uprights: 1800 mm Lsdpfx Anewivddo Ujab Dimensions: 3500 x 1500 x 2100 mm Weight: 6,500 kg Equipped with new and used tooling

Condition: reconditioned (used), functionality: fully functional, LVD 4000 x 200T Press Brake Type PPBL 200/40 Capacity 4000 x 200T Maximum stroke 150 mm Lodpfx Anowtmi Ee Uoab Weight 13.5T With mobile blade rack

Year of construction: 2025, condition: new, functionality: fully functional, Partial segment UKB die / lower tool system AMADA 415 mm V16 R2 85° V22 R2.5 85° V35 R3 85° V50 R4 85° Ljdpjyqyc Ssfx An Ueab Partial segments UKB upper tool system AMADA 415 mm, 150 mm, 35 mm, 15 mm and horn left/right 100 mm R 0.8 / 85° H 66.5 Furthermore, we offer a 835 mm die (manufacturer Eurostamp) which is structurally identical to the offered UKB dies. This die is slightly damaged, but fully functional and is offered for €70.00 if interested.

Condition: excellent (used), Year of construction: 2003, Haco 6m x 225ton CNC Pressbrake Lasdpfx Ansyv Dc Ij Ueb Great working condition 6m capacity x 225ton 2 Axis Year 2003 Light Guards

Condition: new, Year of construction: 2025, functionality: fully functional, Press force: 180 t Bending length: 3100 mm Distance between uprights: 3600 mm Control system: Cybelec CybTouch 15 Stroke: 250 mm Installation height: 470 mm Rapid traverse (down): 180 mm/s Bending speed: 0-10 mm/s Rapid traverse (up): 165 mm/s Total power consumption: 15 kW Machine weight (approx.): 12,500 kg Dimensions: 4000 x 2000 x 3030 mm Standard equipment: Basic equipment: • CNC control system Cybelec CybTouch 15 Windows • 4+1 axes: Y1-Y2-X-R-C • Mechanical crowning system: B-CM • Rear gauge system, model GHP-2 • Servo-driven main motor • Safety system: DSP AP+MCS • LED bar system • CE standard Lsdpfx Aoy Tn Aaon Usab - Upper tool clamping system, PROMECAM, mechanical - Lower tool clamping system, PROMECAM, mechanical

Condition: good (used), Year of construction: 2000, functionality: fully functional, operating hours: 27,169 h, Hydraulic Press Brake Make: TRUMPF Model: TrumaBend V130 Year: 2000 Technical Data Lodpfx Anoy Ryfuo Ueab Brand: TRUMPF Model: TrumaBend V130 Year of manufacture: 2000 Operating hours: 27,169 h (read off) Press force: 130 t Bending length: 3050 mm Stroke: 365 mm Operating pressure: 340 bar Dimensions: approx. L 3.80 x W 2.40 x H 2.95 m Weight: approx. 13 t Equipment • Controlled axes: Y1, Y2, X, R • Movable support arms • CNC controlled crowning • Delem 2D graphical control • Hydraulic upper tool clamping • Pneumatic die displacement • Upper tool: straight 28°, R1.0, H 140mm, L = 3,050mm, segmented • Die V12/30°, R1, H 100mm, L = 3,000mm, segmented • Die V30/80°, R5, H 100mm, L = 3,000mm (6x500) • Die V60/80°, R5, H 100mm, L = 3,000mm (6x500) All information without guarantee. A demonstration under power is possible at any time in our showroom.