Used Gear Shaping Machine for sale (71,087)

Condition: excellent (used), The Gleason BGT 200 H-W universal bevel gear testing machine is used for roll-off, load capacity, and run-out testing, as well as for measuring backlash on the flank, installation dimensions, and sensitivity to displacement in bevel gears with and without axial offset and axial angles from 0° to 180°. Gear sets with a maximum ring gear diameter of up to D=190.5 mm and hypoid gear sets with a pinion offset of 31.75 mm above and below the center can be tested. This testing machine is ideally suited for testing gear sets with small diameters and small modules under low load and with a minimum of backlash. The digital actual value display facilitates quick and precise adjustment and reading of the pinion installation dimension, ring gear installation dimension, and axial offset. The motorized drive of the pinion spindle, in conjunction with the frequency converter, allows for stepless adjustment of the pinion speed in the range of 0 to 3,000 [rpm]. The work area is secured by an electrically interlocked safety device. Technical data Largest gear diameter 190.5 mm Largest axial offset (hypoid offset) above (+) and below (-) the center ± 31.75 mm Largest / smallest distance from the machine center to the spindle nose, ring gear 177.8 / 0 mm Largest / smallest distance from the machine center to the spindle nose, pinion 177.8 / 25.4 mm Smallest / largest axial angle (steplessly adjustable) 0 to 180 ° Pinion and gear spindle: Diameter at the large end 45.65 mm Taper 1 : 24 Todpfj Afi Atjx Akiod Length of the taper 76.20 mm Diameter of the spindle bore, throughout 33.33 mm Speed range of the pinion spindle (steplessly adjustable) 0 to 3,000 rpm Weight 1,050 kg Dimensions L x W x H 500 x 1,100 x 2,000 mm

Condition: used, Year of construction: 2008, max. wheel diameter 700 mm max. module 10 (8) min. module 1 table diameter 530 mm Table speed max. 350 1/min Distance of shafts 50 - 680 0 workpiece weight 4.000 kg Tsdpeyv Ipfsfx Akisd Axial travel 1.000 mm tangential adjustment 300 mm pivoting angle + / - 45 Grad power capacity 32 kW spindle turning speed range 3.500 - 12.000 U/min tool diameter 320 mm total power requirement 80 kW weight of the machine ca. 25,00 t

Condition: ready for operation (used), Wheel width: 600mm, module range: 2-16, cutter dimensions X/Y: 240mm/280mm, table diameter: 1020mm, speed: 200rpm, swiveling: +/-45°, max. wheel diameter with/without counterholder: 1250mm/800mm. Machine dimensions X/Y/Z: approx. 4500mm/2100mm/3300mm, weight: approx. 16200kg. An on-site inspection is possible. Tjdpey Hk T Isfx Akijd

Year of construction: 1992, condition: ready for operation (used), Gear diameter range: 10mm-330mm, gear width: 180mm, max. module: 7, min. module: 0.5mm, clamping length: 420mm, number of teeth range: 10-600, helix angle: +/-45°, speed: 1900rpm, grinding wheel diameter range: 280mm-350mm, grinding wheel width range: 84mm-104mm. Machine dimensions X/Y/Z: approx. 4500mm/6000mm/2300mm, weight: approx. 5100kg, control: Fanuc Series 160i-T. Documentation available. An on-site inspection is possible. Tsdpfx Aozg Iq Ijkiod

Condition: good (used), Year of construction: 1991, weight of the machine ca. ca. 6 t The design of the basic machine is characterised by the following features: - horizontal position of the workpiece spindle; vertical position of the milling spindle or milling head of the milling head - The workpiece is held between the workpiece headstock (left) and the tailstock (right). - the radial slide is mounted on the base (X-axis) - the axial slide moves on the radial slide (Z-axis) - the shift milling head is equipped with an automatic angle adjustment (A-axis); the shift slide (Y-axis) moves diagonally to the workpiece diameter - CNC controlled - IBH control - loading device - Many accessories Todpfx As Agw R Nskiod Technical data: - largest milling module with hobs according to DIN 8002: 4.5 mm - largest milling module for high-performance milling: 3.0 mm - Number of teeth: 2 - 999 - max. workpiece diameter for manual loading: 200 mm - max. workpiece diameter for automatic loading: 150 mm - maximum workpiece length: 400 mm - largest / smallest milling cutter diameter: 102/40 mm - maximum cutter length: 230 mm - largest / smallest milling arbor diameter (standard): 32/16 mm - Axial slide path = largest milling length Z-axis: 300 mm - Radial slide path X-axis: 140 mm - Milling cutter shift path Y-axis: 100 mm - Milling stock path W-axis: 420 mm - Swivelling angle of shift milling head (left/right) A-axis: 50°/60° Milling coordinates: - Z-axis: 100 - 400 mm - X-axis: 1ß0 - 150 mm - Y-axis (end face of milling spindle): 50 - 230 mm - W-axis (face of tailstock spindle): 165 - 585 mm - Milling cutter speed range standard B-axis: 0 - 1500 rpm - Workpiece speed C-axis: 0 - 350 rpm Feed speeds: - X-axis: 3500 mm/min - Z-axis: 3500 mm/min - Y-axis: 4000 mm/min - W-axis: 5500 mm/min - V-axis (gantry loader): 80000 mm/min

Condition: used, Year of construction: 2015, Technical details: Tedpol Ha Ubofx Akiod weight of the machine ca.: 4 t

Condition: excellent (used), Year of construction: 2005, We offer a Weinig Super 4 planer in very good condition with EM 15 feed unit, year of manufacture 2005. Manufacturer: Weinig Model: Super 4 Year of manufacture: 2005 Tedpfx Aeylagmjkisd Condition: very good Type: planer If you have any questions or need further information, please send us a message or contact us by phone.

Condition: used, Year of construction: 2006, Technical details: max. wheel diameter: 300 mm max. module: 7 Tjdpfx Akjyz Sd Rjied weight of the machine ca.: 15 t table turning speeds: 100 U/min table diameter: 180 mm hob turning speeds: 750 U/min max. hob diameter: 300 cutter length max.: 230 mm Liebherr LC300 with loading automation Machine including counter holder The machine used to work with emulsion *

Condition: good (used), Year of construction: 1972, max. wheel diameter 80 mm Tjdpfx Aow N S D Sekisd gear width 60 mm max. module 3 min. module 0,1 total power requirement 0,4 kW weight of the machine ca. 120 kg dimensions of the machine ca. 0,6x0,6x0,75 m

Condition: ready for operation (used), A Welter slotting machine for gear and profile machining is available. Stroke: 1250mm, machine dimensions X/Y: 3800mm/5600mm, weight: approx. 12500kg, control: Siemens. The machine was retrofitted in 2011. Documentation available. On-site inspection is possible. Todpfjx Uq Twjx Akiod

Condition: used, Year of construction: 2008, Maximum workpiece outer diameter 3420 mm workpiece diameter nominal 2400 mm max. module 30 mm control Siemens Sinumerik 840 D Minimal workpiece - internal diameter 630 mm Maximum workpiece outer diameter 3420 mm Maximum workpiece tooth width 600 mm max. rim strength 500 mm Maximum permissible head circle diameter 440 mm Hob/disc cutters – Maximum length 90 mm Milling arbour diameter 80 mm milling head -swivable +15/-15 Grad workpiece table outer diameter 1870 mm Workpiece table bore 600 mm Workpiece table – Maximum permissible load 300 kN rapid traverse X-axis 3000 mm/min rapid travel z-axis 4000 mm/min Workpiece table speed 0-6 U/min Tools speed 18-180 U/min weight of the machine ca. 38 t dimensions of the machine ca. 8,41 x 9,05 x 5,19 m total connected load 100 kVA Equipment/accessories: - IFK2 internal milling head - Milling arbor with spacer discs - Chip conveyor Tedpfx Akjztz Rusijd - Oil mist extraction - Dry machining only - Technical documentation

Condition: good (used), Year of construction: 1985, functionality: fully functional, 1 used Iseli surface grinding machine, model EBW-E. Tsdpfx Aozz Rhlekisd

Condition: ready for operation (used), Year of construction: 1999, functionality: fully functional, For sale: 5-head moulder / four-side planer PAOLONI MASTER 23. Condition: Good. Fully functional and ready for work. Nameplate data: Year of manufacture: 1999 Power supply: 380V / 50Hz / 3 phase Power: 42 kW Weight: 5,500 kg Working parameters: Tsdsyyylgepfx Akisd Working width: up to approx. 230 mm Working height: up to approx. 120 mm Number of spindles: 5 (5 heads) Spindle diameter: Ø40 mm Spindle speed: up to approx. 6,000 rpm Feed speed, adjustable: up to 30 m/min The machine is intended for the production of wooden components – planing and profiling with high repeatability. Suitable for drawer sides, etc. -Control from the operator panel (control panel on the machine) -Convenient starting/stopping of units (heads) -Emergency STOP Possibility to inspect the machine on site. Loading with forklift or by own means. Location: Elbląg / Warmian-Masurian Voivodeship

Condition: excellent (used), max. wheel diameter 130 mm gear width 180 mm max. module 2,5 min. module 0,3 turning speeds 140 - 900 U/min min. number of teeth 4 clamping length max. 200 mm Control Siemens Tedpfx Akjy Umizjied max. workpiece diameter 80 mm total power requirement 3,5 kW weight of the machine ca. 2,9 t dimensions of the machine ca. 1,8 x 1,6 x 1,9 m

Condition: excellent (used), Capacity M16 module Table diameter: 1,200 mm Todpfx Ajzql Ufjkied Maximum workpiece diameter: 1,500 mm Milling slide travel: 600 mm Table center hole diameter: 250 mm

Condition: used, bore capacity in steel (diameter) . mm throat 368 mm bore stroke . mm feed 0,1-6,18 m/min table surface area 560x470 mm Thread-cutting device The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Tsdoz E Svcopfx Akied Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, functionality: fully functional, For sale is an Oerlikon bevel/worm gear unit of the E 37 EX 2 series, serial number 828499L01.1. The unit comes from a fully functional installation and is suitable for test benches, special purpose machines, and industrial drive applications. Todpfx Aoypb Iyokisd Technical specifications (general): Manufacturer: Oerlikon Type: E 37 EX 2 Design: Bevel/worm gear unit Application: Test bench technology, mechanical engineering, industrial drives Condition: used, functional

Condition: used, Year of construction: 1998, Technical details: max. module: 7 weight of the machine ca.: 5 t worm grinding diameter: 280-350 mm width of grinding worm: 84-104 mm min. number of teeth: 6 max. number of teeth: 600 max. top circle diameter: 360 mm max. workpiece weight: 60 kg with Turbo Separator, loading unit, latest-generation balancing and dressing unit and various accessories Tedpfx Akszgw I Noiod *

Year of construction: 2025, condition: refurbished (used), functionality: fully functional, machine/vehicle number: 3649, Country of manufacture: Switzerland Voltage: 380 V / 50 Hz / 3 Phases Net weight: approx. 445 kg Tedpfx Aew Uc Tbjkiod Dimensions: 730 x 780 x 1380 mm Customs tariff number: 8459.6130 TECHNICAL SPECIFICATIONS Maximum distance between stops: 80 mm Maximum cutting length: 50 mm Maximum cutting diameter (with 24 mm dia. cutter): 36 mm Maximum module: 1 Number of teeth cut – with 1:4 ratio: 6-100 with 1:10 ratio: 6-200 Total rapid approach and plunge travel: 8 mm Maximum axial movement travel of the cutter: 10 mm Maximum plunge cutting travel: 2.5 mm Maximum movement of counter-spindle quill: 25 mm Maximum distance between workpiece axis and cutter axis: 30 mm Maximum cutter diameter: 32 mm Quill body diameter: 35 mm Continuously adjustable slide feed rate: 0-60 mm/min Constant rapid return feed rate of the slide: 3 m/min 8 spindle speeds: 660–5300 rpm Horizontal tilt of the cutter head: approx. 4° Cutter motor power (2 speeds): 0.37/0.59 kW Hydraulic pump motor power: 0.24 kW Coolant pump motor power: 0.07 kW Hydraulic oil tank capacity: 13 l Cutting oil tank capacity: 10 l Quill oil tank capacity: 10 l All technical data provided without guarantee and subject to errors or omissions.

Condition: used, Year of construction: 1986, machine/vehicle number: 275590, Ref. No. 25362 Technical Data: - Drilling capacity 25 mm - Drill spindle taper MK 3 - Drill spindle speeds 100 / 205 / 345 / 440 rpm Todeyf Ehiepfx Akijd 695 / 885 / 1450 / 2900 rpm - Drill spindle stroke 130 mm - Drill spindle reach 260 mm - Coordinate table with 3 T-slots 580 x 240 mm - Table travel X-axis: 415 mm Y-axis: 155 mm - Drive 400 V / 0.75 / 0.9 kW - Space required approx. W 900 x H 1800 x D 700 mm - Weight approx. 270 kg - Machine vice

Condition: used, Year of construction: 1999, Technical details: max. wheel diameter: 280 mm max. module: 7 weight of the machine ca.: 13 t Todpoyzxbcefx Akiod table turning speeds: 100 U/min table diameter: 250 mm min. number of teeth: 4 hob turning speeds: 1500 U/min max. hob diameter: 160 cutter length max.: 230 mm Machine in good condition. Available 01.08.2024 *

Condition: ready for operation (used), Year of construction: 2011, A modified MECO internal keyway slotting machine is available. Keyway width range: 4mm-45mm, max. square keyway diameter: 36mm, max. hexagonal keyway diameter: 36mm. The machine was modified and can now slot square and hexagonal keyways. Documentation available. An on-site inspection is possible. Tjdpfey Hvqrex Akisd

Condition: good (used), Year of construction: 1980, functionality: fully functional, Gear-driven drill press, no belt changes required Very quiet and smooth operation - Drilling capacity in steel ST 60: 30 mm - Drill spindle mount: MK 3 - Drill spindle stroke: 160 mm - 9 drill spindle speeds: 90 - 1450 rpm - Overhang: 300 mm - Table with 2 T-slots - Table dimensions, swiveling: 500 x 450 mm - Table dimensions, base plate: 350 x 400 mm - Distance from base plate to spindle nose: 1100 mm - Max. distance table - drill spindle: 660 mm - Height adjustable via rack and pinion with hand crank - Column diameter: 120 mm - Drive: 380 V / 1.2 kW - Space requirement: approx. W 600 x H 2100 x D 670 mm - Weight: approx. 350 kg Tjdpfozuxxfsx Akisd - Includes drill chuck

Condition: used, Year of construction: 2007, max. wheel diameter 400 mm workpiece dia. 36-300/400 mm axis distance 135-290 mm spindle turning speed - stepless 3000 1/min dist. between centers 100-550 mm Control Siemens 840D weight of the machine ca. 4000 kg dimensions of the machine ca. 2000x3055x2788 mm Test method: - Single flank rolling test - Double flank rolling test Todpoy D T Susfx Akied - Structure-borne noise test - Heli testing in two-flank contact. Features: - Use of up to 6 test slides - Highest testing accuracy and repeatability - Machine table with workpiece drive - Swiveling pneumatic unit - Spray oil lubrication (type: Vogel) - Oil mist extraction (type: Elbaron)

Condition: used, Year of construction: 1983, max. wheel diameter 1500 mm gear width 550 mm max. module 25 min. module 2 workpiece weight max. 6000 kg max. number of teeth 432 min. number of teeth 12 table diameter 990 mm grinding wheel size 400 mm total power requirement 75 kW weight of the machine ca. 20,5 t With tailstock max. wheel dia. 1250mm, without tailstock 1500mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Tedpjyq Szaofx Akiod Your Markus Hirsch Team