Used Gannomat Junior 320 for sale (60)

Condition: like new (used), Year of construction: 1993, functionality: fully functional, Dowel and slot mortising machine GANNOMAT JUNIOR 320 LBM Very good condition, like new; the machine comes from a very small joinery and was used only very little. The machine is in its original state and has only been cleaned, with no touch-ups to the paint. You can mill slots and drill dowel holes on two levels without having to reclamp the workpiece. 380V, 1500W Speed: 2800 rpm Year of manufacture: 1993 With this machine, you can mill slots, for example for lock cases and similar applications, or make all types of frame dowel joints, at right angles, butt joints, or mitred joints. Ideal for producing dowel joints in timber frame construction, furniture, door, window, and staircase manufacturing, as well as similar applications. By drilling on two levels, using the stops and indexing rails, and due to the machine’s design, dowel joints can be produced in a very short time, which makes the machine highly efficient. The machine requires a compressed air connection of 6 bar (air consumption is very low). Right-hand rotation. Mills and drills very efficiently and cleanly. Supplied with 2 angle stops (one center stop and one side stop, which can be used on either side), plus a mitre stop. On the front of the machine table, there is a 2000mm long stop rail with 2 flip stops; the stop rail can be shortened or extended if required. Workpiece clamping is done with 2 pneumatic clamping cylinders. Height adjustment between drilling levels is also pneumatic; the pneumatic switch is located at the front of the machine, ensuring rapid adjustment of the index positions and drilling levels. Equipped with a precision 12mm indexing rail, featuring a center index and 12 indices left and right. Can be quickly converted for slot milling; in this mode, the machine can be used without indexing, with 2 adjustable stops left and right, allowing for a maximum working width of 420mm. Maximum drilling hole height: 100mm Maximum drilling depth: 150mm with stop and scale Maximum workpiece height: 160mm Everything functions perfectly. The machine is personally delivered and demonstrated by us anywhere in Germany for €220.00, so you have no risk when purchasing. Delivery to Austria and the EU is also possible on request. The machine table is 870mm wide, 140mm deep at the sides, and 350mm deep in the center. Lsdpfx Asynv E Rjd Aohf Professional equipment, not DIY store scrap. Ready for immediate operation. With 2-jaw drill chucks up to 20mm. Very stable and durable construction. The precision guides with play-free ball bearing bushings are in excellent condition and move smoothly.

Condition: like new (used), Year of construction: 2025, GANNOMAT "JUNIOR 323" FRAME DOWEL AND SLOT MORTISING MACHINE Complete in standard configuration as per price list 01/22/D with: - Precision collet chuck for ER 40 collets Ø 3–26 mm, including collets Ø 10 / 13 / 16 / 20 - Motor 1.5 kW, 2800 rpm - Positioning via digital counter - Pneumatic 2-level positioning adjustment (0–100 mm) - Max. drilling depth: 150 mm - Precision indexing rail with 12 mm pitch, featuring: - Center detent and lateral adjustment 320 mm Lhedjxdttiepfx Ad Asf - 2 pneumatic safety clamping cylinders - Complete fence system consisting of: • 1 center stop and 1 stop for oversized frames • 1 round stop bar approx. 850 mm long (can be mirrored from left to right) • 2 flip stops - Tiltable slot mortising device with 2 program cams (400V, 3Ph, 50Hz, 1.5kW) - Extraction hood Ø 80 mm, dust-tested - Central mitre stop 45° - Pair of auxiliary workpiece supports, pivotable (left and right) - Drill head holder - 3-spindle drilling head, 32 mm pitch (can be rotated 90°) - Chassis with 4 wheels for easy machine movement Availability: Short-term – immediately –

Condition: new, Year of construction: 2026, Universal solid wood boring machine for frames and horizontal mortiser. Short introduction: • Universal application: frames, entry doors, windows, as well as useable as horizontal mortiser, ... • Drilling depth up to 150 mm (larger drilling depths optional) • Pneumatical position height adjustment for 2 levels 0 - 100 mm, adjustable through mechanical digital counters • Drilling in two height positions at a single workpiece clamping position • Pneumatic clamping cylinders • Multi spindle drillheads (option) Lodpfxjdx R D Sj Ad Ashf • Pneumatic feed (option) • Mobil through castors (option) or with pallet trucks

Condition: used, Year of construction: 1989, Used machine Lhodewkba Hepfx Ad Asf Year of manufacture: 1989 Equipment and technical data: - 2-jaw drill chuck for up to 20 mm shank diameter - Pneumatic position adjustment on 2 levels, 0-100 mm - Max. drilling depth 150 mm - Precision indexing rail 12 mm - Central locking and cross adjustment - 2 pneumatic safety clamping cylinders - Motor 1.5 kW - Speed 2800 rpm Dimensions (without stop): 1100 x 1100 x 1500 mm Weight: approx. 310 kg Availability: short-term Storage location: Röllbach

Condition: used, Year of construction: 1993, Used machine Year of manufacture: 1993 Features and technical data: 2-jaw drill chuck up to 20 mm shank diameter Pneumatic positioning adjustment on 2 levels 0-100 mm Max. drilling depth: 150 mm Lhjdpfx Adjw I Uy Te Aef Precision indexing rail 12 mm Center locking and cross adjustment 2 pneumatic safety clamping cylinders Motor 1.5 kW Speed: 2800 rpm Long hole drilling device, lowerable, with 2 program cams Machine weight approx. 310 kg Machine dimensions (W x D x H): 1100 x 1100 x 1500 mm (without stop) Availability: short-term Location: Röllbach

Condition: as good as new (ex-display), Year of construction: 2026, - NEW - Manufacturer: Ganner Gannomat Model: SELEKTA 253 220 V, 1 Ph, 50 Hz Complete in standard configuration with: - Fully automatic electronic control with program selector switch for RINSING – GLUING – GLUING/DRIVING-IN - Dowel feed via electronic vibratory feeder with potentiometer for stepless adjustment of dowel feed rate - Automatic dowel diameter and length detection with Auto-DL-Select system (automatic ejection of dowels with incorrect lengths +/- 5 mm into collection container) - Closed glue system with 6 bar glue pressure via glue nozzle for adhesives with viscosity from 150 to 350 mPas - Stepless electronic adjustment of glue quantity with potentiometer by electronic time preselection - Selector switch for GLUE/WATER to rinse/clean the glue system, with EasyClean function button (automatic cleaning program for glue hose and glue nozzle via spray funnel and wastewater collection container) - Indicator lamp for glue level display in the glue container - 1 stainless steel container for 5 kg glue and 1 stainless steel container for 5 l water (for rinsing/cleaning) - 4 rollers for easy movement of the machine Including 1 gun for dowels Ø 8 mm, dowel length 25 – 40 mm, drive-in projection 7 – 20 mm Air connection: 6 bar Price ex stock 54634 Bitburg - Immediately available - Ljdpfx Adedwi Rke Ashf

Condition: new, Year of construction: 2026, Gannomat Concept 70 Eco Lamella – Carcase Press with Rapid Traverse Technical specifications: Lsdpfxey Egz So Ad Ajhf Lamella carcase press from our showroom; Working range: width from 150 to 2,500 mm, height from 150 to 1,400 mm, depth 700 mm; - Upper lamella pressing beam with 6 elements, side lamella pressing beam with 5 elements - Lamella pressing beams with field-proven tolerance compensation for tightly pressed carcase joints - Counter-pressure surfaces are continuous, coated support plates, 40 mm thick - The pressing force of the pressing beams is infinitely variable via two potentiometers and set electronically via frequency converter, ensuring absolutely wear-free torque transmission. - Pressing force for horizontal pressing beams: min. 500 daN (kg) up to infinitely adjustable 2,200 daN (kg) max. - Pressing force for vertical pressing beams: min. 300 daN (kg) up to infinitely adjustable 2,200 daN (kg) max. - Including option: Rapid traverse speed for quick positioning of the pressing beams, controlled by automatic workpiece detection with sensors in the pressing beams; pressing speed 5/10/25 mm/sec and rapid traverse speed 50 mm/sec. Sensors can be deactivated for pressing special parts. - Jog mode for precise positioning of both pressing beams, e.g., for low pressing forces, drawers, and carcases at 45 degrees. Easy operation via six separate push buttons, freely adjustable pressing time preselection with automatic opening feature, loading height 300 mm. The machine is available from our showroom and can be delivered immediately. Location: ex-stock 54634 Bitburg - available immediately -

Condition: used, Year of construction: 2014, Used machine Year of manufacture: 2014 Equipment and technical data: Working area X = 1300 mm Working area Z = 80 mm Number of separate units: 2 CNC axes: 2 Vertical drills: 3 Horizontal drills Y: 3 Motor: 1.5 kW With dowel insertion via vibratory feeder With glue system Ledpfjy E Awvex Ad Aehf Dowel diameter: 8 mm Dowel length: 35 mm 4-position field occupancy Alternating feed With pneumatic clamps Control: Beckhoff Availability: by arrangement Location: 63934 Röllbach

Condition: good (used), Year of construction: 1998, Universally applicable frame dowel and slot drilling machine with angle adjustment Especially designed for stair construction, window manufacturing, and versatile applications thanks to pneumatic height adjustment. Angled dowelling and spindle drillings, such as for balusters, can be easily accomplished with the swiveling drilling unit. Motor with pole switching, two speeds Motor power: 1.0 / 1.5 kW, 1400 and 2800 rpm Motor start via convenient handle switch Equipped with Röhm two-jaw chuck, 1 - 20 mm Linear laser for precise workpiece positioning Drilling unit can swivel 65 degrees left and right Pneumatic adjustment of working height allows dowelling on two levels without repositioning. Desired drilling heights can be set for each drilling level via digital counter, switching between levels is pneumatic and operated from the front Cross adjustment 340 mm, infinitely variable or in 12 mm increments via indexing rail Pneumatic clamping possible at any point, operated from the front Lodpfxoxmatno Ad Ajhf Maximum height adjustment approx. 100 mm above table height Drilling stroke approx. 200 mm 2 pneumatic workpiece clamps, 1 clamping column repositionable to the front 2 swiveling workpiece supports Extraction funnel Central stop + 1 side stop Fixed mitre stop Length stop as round rod Assorted drill bits Operating manual CE mark Machine was partly repainted due to paint splashes. Pneumatic hoses replaced Dimensions: approx. 1200 x 1350 x 1600 mm (LxWxH), weight 380 kg. The machine can be viewed and demonstrated at our premises by appointment. We only offer machines that are ready for demonstration in our warehouse, see "more offers from this seller."

Condition: good (used), Year of construction: 1992, functionality: fully functional, double-row line boring machine GANNER with 21 spindles each Ledpfx Adexlt T Ss Ajhf

Condition: excellent (used), For sale: dowel inserting machine from Ganner in very good condition. Lodpfxjyyahne Ad Ajhf

Condition: excellent (used), Year of construction: 1990, functionality: fully functional, hole spacing: 32 mm, Ganner Gannomat belt and line boring machine Blum and Grass drill head 7 Spindle row hole drilling head Lhodpfx Aeq E Ur Aed Aof incl. extension rulers 32 mm system pneumatic version

Condition: used, Year of construction: 1989, Working dimensions 3000 x 1250 x 650 mm Cylinder stroke 110 mm Machine dimensions 3240 x 2120 x 770 mm Weight approx. 900 kg Lsdjxu Egvopfx Ad Ajhf

Condition: ready for operation (used), Year of construction: 2011, functionality: fully functional, operating hours: 24,058 h, power: 7 kW (9.52 HP), input voltage: 480 V, input current: 10 A, input frequency: 50 Hz, type of input current: three-phase, travel distance X-axis: 1,000 mm, workpiece length (max.): 4,000 mm, workpiece width (max.): 1,000 mm, workpiece height (max.): 60 mm, workpiece weight (max.): 70 kg, number of axes: 3, actuation type: pneumatic, total height: 1,430 mm, total length: 2,300 mm, total width: 1,500 mm, overall weight: 1,100 kg, table length: 3,300 mm, table width: 1,000 mm, Equipment: CE marking, documentation/manual, Gannomat 570 ProTec T2, BK6, Drilling and Grooving, still connected for demonstration purposes, in good condition. The ideal machine to complement a CNC machining centre, designed for highly efficient cabinet production with minimal setup times starting from batch size 1. Also perfectly suitable as an entry-level machine for CNC-controlled processing technology at a low entry price, ideal for smaller carpentry or joinery workshops focused on efficient and precise cabinet fabrication. Potential applications include, for example: Form-fit and force-fit as well as tolerance-free joints, such as dowel joints, line boring (row hole drilling), hardware drilling for furniture hinges, lock bores, various connectors such as Rastex, Cabineo, and much more. Includes accessories such as manual with wiring diagram, a selection of drill bits, and an extraction connection pipe. The machine can be quickly prepared for loading and is located at ground level. Lsdpfx Ajytxpved Ashf

Condition: used, Year of construction: 2019, Machine design: Through-feed/return-feed Working size in X direction: 1300 mm Working size in Y direction: 5600 mm Working thickness (Z dimension): 60 mm Number of main spindles: 1 unit Main spindle power: 5.5 kW Main spindle speed: 1,000–20,000 rpm Clamping system: HSK-63 F Tool changer: Pick-up changer Tool change positions: 3 units Rear wall groove unit: fixed in Y direction Vertical drilling spindles (X direction): 3 units Vertical drilling spindles (Y direction): 10 units Horizontal drilling spindles (X direction): 2 units Horizontal drilling spindles (Y direction): 6 units Control type: PC control Operating system: Windows Lhodpsymp N Tjfx Ad Aef Typewriter keyboard: Yes Mouse: Yes Programming system: Gannomat Editor DXF interface: Yes Office version available: Yes Online connectivity possible: Yes Table version: fixed, smooth table Central lubrication: automatic Tools: various tools Operating hours: 920 hours Approx. weight: 1,800 kg Extraction diameter: 3x80 mm The machine has been modernized at the factory; pressure beam and control technology from model 0572! Stock location: Customer

Condition: new, Year of construction: 2025, GANNOMAT "MASTER 325" FRAME DOWEL AND MORTISE BORING MACHINE Specifically designed for staircase construction Complete in standard configuration according to price list 01/19/D, featuring: - Precision collet chuck for ER40 collets Ø 3-26 mm, incl. collets Ø 10 / 13 / 16 / 20 - Pole-switchable motor 1400/2800 rpm, 1.5 kW - Line laser with bracket - Boring unit, continuously rotatable from the front (65°-0°-65°) - Position setting via digital counter - Position adjustment for 2 levels, pneumatic (0-100 mm) - Maximum boring depth 200 mm - Precision indexing rail with 12 mm pitch with central detent and lateral adjustment 320 mm - Complete stop system consisting of: 1 center stop and 1 stop for oversized frames 1 stop rod, approx. 850 mm long (can be reversed from left to right) 2 flip stops - Mortising unit lowerable, with 2 program cams (400V, 3Ph, 50Hz, 1.5 kW) Extraction funnel, dust-tested, Ø 80 mm Double miter stop adjustable from 0°-60° Pneumatic clamping of the X-axis with on/off switch at the indexing handle Pair of auxiliary workpiece supports, swiveling (left and right) Lhedoxdttpopfx Ad Aof Clamp column re-positionable to the front Chassis with 4 wheels for easy machine movement 1 piece Collet extension Ø 20 mm, incl. collet for drill shank Ø 9 mm 1 piece Baluster drill bit Ø 25 mm, chrome steel, with centering tip Available: at short notice

Condition: new, Year of construction: 2026, FLAT PANEL CASE CLAMP GANNOMAT "CONCEPT 70 EASY 170" Fully equipped in standard configuration with: Lodew Sgnkopfx Ad Aohf - Sturdy, torsion-resistant steel frame made with welded and bolted construction - Lateral pressing beam with continuous pressure surface, equipped with a 25 mm thick coated support plate - Counter-pressure surfaces (side pressure wall, base) are continuous, 25 mm thick coated support plates - Electromotoric adjustment of the pressing beam via precision trapezoidal threaded spindles (with increased pitch and concentric accuracy) and high-performance carriage nuts with grease reservoir - Pressing is performed by electromotor via worm gear motor (0.75 kW) - The pressing force of the pressing beam is infinitely variable and electronically set via potentiometer, regulated by frequency converter, allowing completely wear-free pressure force control - Pressing force for vertical pressing beam: min. 300 daN (kg) up to stepless max. 2200 daN (kg) - Pressing and adjustment speed of the pressing beams with fine positioning, via 3-stage selector switch: 5 / 10 / 25 mm per second - Jog mode for precise positioning of the pressing beam, e.g. for low pressing forces such as drawers, etc. - Extremely simple operation via two separate pushbuttons; two motion sequences (open/close) can be selected via controller - Freely adjustable pressing time preselection 0–30 min (switchable to seconds or hours), with individually programmable opening dimensions for both pressing beams - Re-pressing function to increase or decrease the pressing force during the pressing process - Working height/loading height: 200 mm - Working dimensions: Length min: 150 mm, max: 1300 mm Height min: 150 mm, max: 1700 mm Depth: 700 mm Electrical connection: 400 Volt, 50 Hz, 16 A Available: at short notice

Condition: new, Year of construction: 2025, CNC-controlled drilling, gluing, and dowel insertion machine Complete in standard configuration with: - Support with linear guide consisting of: 1 pc. single-spindle horizontal drilling unit, motor 0.65 kW, stroke 70 mm Tool speed selectable via operator software (3000/5000/8000 rpm) 1 pc. blow-out, gluing, and dowel insertion station for dowels Ø 8 mm, dowel length 25–50 mm - Fully automatic, electronically controlled central lubrication - X-axis NC controlled, with working length 700 mm, max. traversing speed 95 m/min - Z-axis manually adjustable via mechanical digital counter, position on support table 5–40 mm - Dowel insertion projection adjustable from 7–20 mm via mechanical digital counter, drilling depth 0–35 mm (with drill length TL 70 mm), automatically set with insertion projection - Closed glue system with 6 bar glue pressure via glue nozzle, for glues with viscosity from 150 to 350 mPas - Glue quantity steplessly adjustable via operator software - Selector switch GLUE/WATER to flush glue system, each with: 1 stainless steel container for 7.5 kg glue and 7.5 l water - Indicator lamp for residual glue level in glue container - 1 pc. left side stop, 1 pc. right side stop (all removable) - 2 pcs. start buttons for individual operation with 1–2 workpieces - 2 pcs. pneumatic angled clamping cylinders 10° for workpiece thickness up to max. 80 mm, workpiece length (Y) min. 70 mm - 1 pc. extraction funnel, connection Ø 80 mm - 1 pc. TCT controller with: Integrated industrial PC, incl. Beckhoff TwinCAT soft PLC, operating temperature range 0–50°C, 15" capacitive touchscreen TFT industrial display, operating system: WINDOWS 10 IoT LTSC (long term support channel) - Programming via menu-guided user software, drilling distances freely programmable with ABSOLUTE, RELATIVE, or GRID dimensioning, automatic workpiece mirroring and process optimization, 2 working fields assignable with different programs, graphical workpiece display, parametric programming, zero-point shift, programmable work lists, plain text error diagnosis - Integrated options: - Electronic optical glue monitoring system G.I.C. (Glue Insert Control) for 1 pc. glue nozzle, art. no. 0470-0810 - 1 EASY CLEAN system, for automatic test glue shots before starting the drilling/gluing/dowel insertion program. E.C.S. for 1 pc. glue nozzle, art. no. 0471-Z010 - 1 single-spindle vertical drilling unit from ABOVE, 0.65 kW, Lsdpfx Asw Sgm Hed Ajhf (3000/5000/8000 rpm), position (Y) manually adjusted via mechanical digital counter Adjustable from 5–40 mm, drilling depth (Z) max. 30 mm (with drill length TL 57 mm) Workpiece thickness (Z) max. 50 mm, workpiece length (Y) min. 130 mm (incl. drilling depth compensation, e.g., for Häfele Minifix) Art. No. 0471-0830 - 4 vertical angled clamping cylinders 10° with mount, additional, Art. no. 0470-0850 Available: short notice

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Lamella - carcass press with rapid traverse Technical data: Lhodpfxoiidm Ns Ad Asf Lamella carcass press from our showroom; Working range: width from 150 - 2.500mm , height from 150 - 1.400mm; depth 700mm; - lamella press beam top with 6 elements, lamella press beam side with 5 elements - lamella press beam with practice-proven tolerance compensation for tightly pressed carcass joints - Counterpressure surfaces are 40 mm thick, coated continuous support plates - The pressing force of the pressing bars is infinitely variable electronically controlled by 2 potentiometers and adjusted via frequency converter, therefore the torque transmission is absolutely wear-free. - Pressing force for horizontal press bars min. 500 daN (kg) to infinitely variable max. 2200 daN (kg) - Pressing force for vertical press bars min. 300 daN (kg) to stepless max. 2200 daN (kg) - Including option: Rapid traverse speed for fast positioning of the press bars, controlled by automatic workpiece recognition with sensors in the press bars, press speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Jog mode for precise positioning of the two pressing beams e.g. for low pressing forces, drawers and carcasses 45 degrees. Simple operation via 6 separate pushbuttons, freely adjustable pressing time preselection with automatic opening, loading height 300 mm. Machine is in our showroom and can be delivered immediately. Location: ex stock 54634 Bitburg - immediately available -

Condition: ready for operation (used), Year of construction: 2020, machine/vehicle number: 435.046, functionality: fully functional, workpiece length (max.): 5,600 mm, workpiece height (max.): 60 mm, workpiece weight (max.): 75 kg, working width: 1,300 mm, rotational speed (max.): 20,000 rpm, TECHNICAL DETAILS Working width: 1,300 mm Lsdpfjxnyn Iex Ad Aehf Workpiece dimensions Workpiece width (X): 60 - 1,300 mm Workpiece thickness (Z): 6 - 60 mm Workpiece length (Y): 263 - 5,600 mm Workpiece weight: max. 75 kg Drilling spindles: 13 vertical, 6 horizontal in Y, 2 horizontal in X Grooving unit: 1 in Y Milling unit motor power: 5.5 kW (S1) Speed range: 1,000–20,000 rpm Tool holder: HSK63F Maximum cutter length: 130 mm MACHINE DETAILS Electrical connection: 400 V, 3 phases, 50 Hz, 12 kVA, 17.5 A Air supply: 7 bar EQUIPMENT Counter-pressure device for 1,300 mm working width Foldable roller table 765 mm for front and rear of the machine, width 500 mm Auxiliary stop 600 mm with integrated rollers for roller tables Additional safety device with lamella curtain Extraction distributor: ∅ 160 mm / ∅ 80-80-80 mm, spacing 196 mm Documentation

Condition: used, Year of construction: 2023, New demonstration machine! List price: €86,567 net Base machine complete in standard configuration for drilling and grooving: For detailed technical data, please refer to the ProTec Type 0571 data sheet. Processing unit with: PowerBlock with 21 spindles and 1 grooving saw - 13 vertical drilling spindles - 6 horizontal drilling spindles in Y - 2 horizontal drilling spindles in X - 1 grooving unit in Y 4th drilling axis in Y Workpiece sizes and weights - Workpiece width (X): min. 60 mm / max. 1000 mm - Workpiece thickness (Z): min. 6 mm / max. 60 mm - Workpiece length (Y): min. 250 mm in through-feed modemax. 5600 mm programmable workpiece length in software - Workpiece weight: max. 75 kg Milling unit Profit HSK63F with 3-position magazine for automatic tool change, motor 5.5 kW (S1), 1000–20,000 rpm with frequency converter, clockwise and counterclockwise rotation, for tool holders HSK63F with collet chuck 462E/OZ25, cutter length up to 130 mm. Information: Machining unit MultiUnit with PowerBlock with 21/23 spindles, grooving saw and optional Profit milling unit. Connected load 12 kVA Rated current 17.5 A Fuse 32 A Voltage 400 V, 50 Hz, 3 Ph (without transformer) Network TN or TT Pneumatic connection 7 bar (102 psi). At the machine: coupling plug (quick coupling) ¼, DN7.2, brass, factory-supplied. For the machine: coupling socket (quick coupling) ¼, DN7.2, brass, customer side. Supply line, inner hose diameter 12 mm (min.). Compressed air consumption continuous operating air consumption approx. 230 L/min (approx. 3.8 L/sec) (compressed air). Extraction connection 3x extraction outlets dia. 80 mm. Extraction air velocity 30 m/sec - measured at the extraction outlet. Extraction requirement min. approx. 2500 m3/h. Machine weight approx. 1650 kg (with options!). Machine installation area: In general, a ProTec fix can be bolted to the floor. A concrete floor (or foundation) is required (at least at the four machine corners/feet). Equipment: Protec 571 Profit HSK63F with 3-position magazine. Roller table 765 mm (Y-axis), foldable, for machine front, width 500 mm. Roller table 765 mm (Y-axis), foldable, for machine rear, width 500 mm. Auxiliary stop 600 mm with integrated rollers for roller tables. Additional safety device with lamella curtain. Prerequisite for horizontal routing for Lamello P-System (without Lamello P-System tools). Drill bit set for Protec shank ø 10 mm with clamping surface (JSO) 1 HW-roof tip drill bit 5x70mm (NL 35mm), LH # 30566-5-05035-L 3 HW-dowel drill bits 5x70mm (NL 35mm), RH #30540-5-05035-R 4 HW-dowel drill bits 5x70mm (NL 35mm), LH #30540-5-05035-L 3 HW-dowel drill bits 8x70mm (NL 35mm), RH #30540-5-08035-R 5 HW-dowel drill bits 8x70mm (NL 35mm), LH #30540-5-08035-L 2 HW-dowel drill bits 10x70mm (NL 35mm), LH #30540-5-10035-L 1 HW-cup drill bit 15x70mm (NL 35mm), LH #30300-5-15070-L 1 HW-cup drill bit 20x70mm (NL 35mm), RH #30300-5-20070-R 1 HW-cup drill bit 35x70mm (NL 35mm), RH #30300-5-35070-R 1 HW-grooving cutter ø 125/30 mm groove width (SB) 4.0 mm, Z=12, LH, Leitz Only for chipboard and MDF, solid wood on request and subject to agreement Tool holder HSK63 F 3.00 pcs For collet 462E/OZ25 Collet 462E/OZ25 for shank 25 mm 3.00 pcs Indexable insert shank cutter Z1+1 1.00 pc HW with indexable insert drill tip ø20, S25, LH 120, L2/L3 58 mm Grooving cutter HW indexable inserts Z1 1.00 pc with indexable insert drill tip, D Ø 10 mm, d Ø 10 mm, L1 75 mm, L2 25 mm, L3 40 mm, RH (adapter 0571WAB10 to be ordered separat Lhedpfsw Tfzfsx Ad Ajf

Condition: used, Year of construction: 2017, Number of drilling spindles: 21 pcsPitch: 32 mmDrill chuck: Clamping surface of drill shank: 10 mmOperation: foot pedalTools included: yesDrilling direction: from below & end faceTilting: manualTilting angle: only 0° or 90°Max. pass-through height: 80 mmMax. pass-through width: 750 mmNumber of material clamps: 3 pcsType of material clamping: pneumaticDesign: stationaryStop system: only for structural seriesWeight approx.: 400 kgMotor power: 1.5 kWDust extraction diameter: 120 mmStorage location: with customer Ledpfoihghrox Ad Ajhf

Condition: used, Year of construction: 2024, New display machine! List price: €32,665,- complete in standard configuration with: Sturdy, torsion-resistant steel frame constructed with welded and bolted assemblies. Louvered top press beam with 6 elements; louvered side press beam with 5 elements. Louvered press beams feature the proven Ganner system tolerance compensation for tightly pressed carcass joints. Counterpressure surfaces (side pressure wall and bottom) are 38 mm thick, coated, continuous support plates. Continuous pressing surface with a height of 95 mm at the lower vertical press beam. Electromotive adjustment of both press beams via precision trapezoidal threaded spindles (with increased pitch and running accuracy) and high-performance running nuts with grease reservoir. Pressing is performed electromechanically via two separate worm gear motors (2 x 0.75 kW). The pressing force of the press beams is continuously adjustable via 2 potentiometers and controlled electronically by frequency converters, ensuring absolutely wear-free force control. Pressing force for the horizontal press beam: min. 500 daN (kg), steplessly adjustable up to max. 2200 daN (kg). Pressing force for the vertical press beam: min. 300 daN (kg), steplessly adjustable up to max. 2200 daN (kg). Pressing and adjustment speed of the press beams with fine positioning, selectable via three-position rotary switch: 5 / 10 / 25 mm/second. Very simple operation using 6 separate push buttons; 8 movement sequences selectable via control system. Freely adjustable pressing time preselection with automatic opening from 0–30 min (switchable to seconds or hours). Working height/feed height: 300 mm. Working dimensions: Length min: 150 mm, max: 2500 mm; Height min: 150 mm, max: 1400 mm; Depth: 700 mm. Weight: approx. 1800 kg net. Dimensions (Length x Width x Height): 3.45 m x 0.95 m x 2.30 m. Electrical connection: 400V, 3Ph, 50Hz (3.2 kVA, 16A). Additional equipment: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams. Pressing speeds of 5 / 10 / 25 mm/sec and rapid traverse speed of 50 mm/sec; sensors can be deactivated for pressing special components. 1 set of machine feet (working height 500 mm). Lsdpfxouf Hx Hs Ad Ajhf Storage location:

Condition: used, Year of construction: 1999, machine/vehicle number: 1088.968, functionality: fully functional, operating hours: 55 h, total width: 700 mm, total length: 900 mm, total height: 650 mm, overall weight: 70 kg, number of spindles: 5, We offer this used Gannomat Modell204 hinge drilling machine, year of manufacture 1999. Manufacturer: Gannomat Model: Modell204 Year of manufacture: 1999 Condition: used Category ID: 659 Ledpfxeyak Hyj Ad Ajhf Type ID: 2533 Machine type: hinge drilling machine If you have any questions or need more information, feel free to write us a message or give us a call.

Condition: reconditioned (used), Year of construction: 1990, Motors 2x1.85A 50Hz 380V 2800 rpm Air operating pressure 6 bar Lsdpfov Nptmjx Ad Ajhf 30 spindles D=10 mm mount Combination foot switch Emergency stop switch Main switch Manual height adjustment Manual side adjustment