Used Flange for sale (1,438)

Condition: used, This listing is for a QuattroFlow QF150 Diaphragm Pump. The unit is in full working condition and is ready for immediate release. The Quattroflow 150S is a 4-piston Diaphragm pump, which is mainly used to pump water-like fluids that are typically handled in research-, pilot plant- or production facilities of the pharmaceutical, biotech, food or cosmetic research centres or plants. Examples: • Solutions containing proteins (albumin, IgG, Clotting factors, monoclonal antibodies, enzymes, vaccines.) • Solutions of polymers or suspensions (silicon, latex, chromatography media) • Cell suspensions (bacteria, yeast, algae, fungi, mammalian cells) • colloidal solutions • Suspensions of viruses or phage • Dairy products • Gelatine • Supplements and ingredients for cosmetic and food Flow rate max.: Eccentric shaft 3° l/h (lpm) 100 (1.67) 100 (1.67) Eccentric shaft 5° l/h (lpm) 180 (3) 180 (3) Flow rate min.: Eccentric shaft 3° l/h (lpm) 1 (0.017) 1 (0.017) Eccentric shaft 5° l/h (lpm) 1 (0.017) 1 (0.017) Pressure: Temperature of fluid < 40°C bar (psi) 6 (87) 6 (87) Temperature of fluid > 40°C bar (psi) 4 (58) 4 (58) Temperature max.: Fluid °C (°F) 80 (176) 80 (176) CIP °C (°F) 90 (194) 90 (194) SIP °C (°F) 130 (260) 130 (260) Autoclave °C (°F) 130 (260) 130 (260) Suction lift dry at: 3000 rpm 3000 rpm Eccentric shaft 3° m (ft) 1-1,5 (3.2-4.9) 1-1,5 (3.2-4.9) Eccentric shaft 5° m (ft) 2-3 (6.6-9.8) 2-3 (6.6-9.8) Volume specifications: Approximated volume per revolution at free output ml 0,72 (3°) 1,2 (5°) 0,72 (3°) 1,2 (5°) Filling volume without connectors ml 15 15 Rcodpoxx Avpsfx Aa Eek Residual volume (after idle with highspeed motor) ml 1-3 1-3 Product wetted surface (approx.) cm² (inch²) 112 (17) 112 (17) Speed range pump rpm 10-3000 10-3000 Connection specification inlet (standard) Connector " 1/4" TC 1/4" TC Flange diameter mm (inch) 25 25 Internal diameter mm (inch) 4,7 4,7 Connection specification outlet (standard) Connector " 1/4" TC 1/4" TC Flange diameter mm 25 25 Internal diameter mm (inch) 4,7 (0.19) 4,7 (0.19) Position of connectors Inline Inline Number of flow directions 4 4 Diameter drive shaft mm 7 7 Product wetted materials (standard): Pump housing SS316L SS316L Valve plate SS316L SS316L Diaphragms Santoprene Santoprene Valves EPDM EPDM O-rings EPDM EPDM Non-product wetted materials (standard): Pump housing SS316L SS316L Bearing housing SS316L SS316L Base plate SS316 SS316 Hood SS316 SS316 Dimensions pump with motor and housing: Length mm (inch) 257 (10,2) 277 (10-91) Width mm (inch) 164 (6,5) 200 (7,87) Height mm (inch) 185 (7,2) 195 (7,67) Weight pump with motor and housing kg (lb) 9,8 (22) 11,2 (25) IP protection class pump IP 54 54 Operating temperature range °C (°F) 0…40 (32…104) 10…30 (50…86)

Condition: used, Year of construction: 2006, Web height min 80mm. max 1220mm. Flanges height min 42mm.max. 600mm. U channels min. 80mm 1200mm Flanges height min.45mm max 300mm. Angles min. 80x80x8mm max.300x300x50mm Flats min.100mm max.1220mm Square tubes min.80x80mm max.600x600mm Rectangular tubes min. 80x40mm max.1200x600mm Positioning weight max. 15000Kg Linear weight of the section to be handled max. 750Kg/m Carriage speed max. 30m/min. No. of drill heads 3 - two horizontal Drill Heads with single spindle Rcjdpsx N Iclefx Aa Eek - one vertical Drill Head with single spindle Max. drilling diameter 50 mm. - with tapered adaptor No.4 Max. thickness that can be drilled 75 mm. Spindle rotation motor per head (a.c.) 15 kW Spindle R.P.M. (with continuous adjustment by program) RPM 180 - 3000 Positioning stroke to suit the gauge line :- vertical drilling unit 20 to 1200 mm.- horizontal drilling units 10 to 600 mm. TOOL CHANGE - number of tools change devices n. 3 - number of tools to be changed n. 6 - adaptor size ISO 45 Model 1260 BH for sections cold sawing : - sawing capacity at 90° min. 80 x 10 mm - sawing capacity at 90° 1250 x 600 mm - sawing capacity at 45° 800 x 600 mm - sawing capacity at 60° 500 x 500 mm - sawing band motor 11 kW - sawing speed 20÷100 m/min. - band size 67 x 1.6

Year of construction: 2014, condition: excellent (used), functionality: fully functional, Ermak Model EKM80/150MTB universal ironworking machine., Serial number 51273-B690FC. Year 2014. PUNCHING 80-Ton punching pressure Max diameter 40mm at 14mm thickness Max thickness 24mm at 24mm diameter. Throat depth 510mm Stroke length 70mm Cycles/min at 15mm stroke 35 pieces Table size 625 x 550mm Working height to die 1200mm FLAT SHEARING Flat Bar (Max. thickness) 300 x 20mm Flat Bar (Max width) 450 x 15mm Blade Length 475mm Angle Flange Trim 80mm Working Height 1020mm ANGLE SHEARING At 90 Degree shearing 130 x 130 x 13mm At 45 Degree miter shearing 70 x 70 x 7mm Working height 1225mm BAR SHEARING Round Bar Shearing 45mm Rjdpevmzlcsfx Aa Eock Square Bar Shearing 45mm Working height 1355mm NOTCHING Material thickness 12mm Rectangular notching width 52mm Rectangular notching depth 52mm V notcher ( side x side x T) 52 x 52 x 12 Working height 1015mm

Condition: used, Year of construction: 1982, Technical details: grinding diameter: 600 mm grinding length: 3000 mm centre height: 315 mm workpiece weight max.: 3000 kg work piece spindle speed: 8 - 120 U/min grinding wheel motor: 25 kW grinding wheel speed: 45 m/sec grinding wheel width x diameter: 750 x 80 mm table speeds: 30 - 4500 mm/min feeds of grinding head: 0 - 5 mm/min table swivelabel +/-: 7,5 ° total power requirement: 55 kVA weight of the machine ca.: 18 t dimensions of the machine ca.: 11,5 x 4 x 2,2 m - Internal grinding device Rodpfovb Dl Ujx Aa Eeck - taper grinding up to 10,1° based on diameter - automatic grinding cycle - grinding wheels and flanges - dressing device - coolant attachment - dust exhauster, various steady rests *

Condition: good (used), hydraulic pump, oil pump, hydraulic unit, hydraulic pump, hydraulic pump, traction motor, drive motor Rjdpfx Ajvvikxsa Esck -Manufacturer: Bosch, hydraulic pump -Type: Shaft: conical Ø 14-17 mm -Flange: Ø 80 mm -Number: 2x pumps available -Price: per piece -Dimensions: 125/90/H120 mm -Weight: 3.3 kg/piece

Condition: refurbished (used), TECHNICAL SPECIFICATIONS Rotary table diameter: 600 mm Magnetic plate diameter: 600 mm Segment holder (or diamond grinding wheel) diameter: 430 mm Maximum grinding height: 400 mm Table rotation speed, continuously adjustable: 1-20 rpm Vertical automatic increments: 0.001 mm Spindle motor power: 37 kW Grinding spindle speed, continuously adjustable: 500-1000 rpm Maximum load on table: 900 kg Net machine weight: approx. 7500 kg Power supply: 400 V +/- 5% 3 Phases, 50 Hz Control circuit voltage = 24 V DC TECHNICAL DESCRIPTION • Frame and uprights made of electro-welded, thermally stabilized steel, with high rigidity and reinforcing ribs. Vertical movement of the spindle head • Precision linear slides • Vertical movements of the grinding wheel head via high-precision ball screws + YASKAWA brushless shaft motor • Vertical movements of the grinding wheel head via electronic handwheel. • Minimum programmable value = 0.001 mm. • Display showing the vertical position of the grinding wheel head, 0.001 mm resolution Transverse movement of the rotary table • Precision linear slides • Transverse movement of the rotary table via high-precision ball screws + YASKAWA brushless shaft motor. Rcjdpex N I A Ssfx Aa Esk • Transverse table movements via electronic handwheel. • Minimum programmable value = 0.001 mm. • Display showing the vertical position of the grinding wheel headstock, 0.001 mm resolution. Spindle Motor • Coaxial spindle with drive motor • Balanced 37 kW spindle motor, without drive belt or coupling. • Frequency converter for continuously variable spindle speed and rapid braking of the spindle motor at the end of the cycle. Rotary Table • Cast iron rotary table with hydrostatic slides. • Drive via Siemens brushless motor • Continuously adjustable table speed from 1 to 20 rpm STANDARD EQUIPMENT • Electropermanent magnetic chuck, 600 mm diameter with parallel poles, complete with electronic control and attraction force adjustment • Electronic handwheel for manual movement of the vertical and transverse axes. • LODI CNC Type T 2000 • Encoder-based measuring system for the vertical and transverse axes. Resolution = 0.001 mm • Automatic cycle with different feed rates for the various cycle phases: roughing, finishing, and sparking. • Cast iron rotary table with hydrostatic slides • Rotary table speed continuously adjustable by brushless motor • Frequency converter for continuous spindle speed adjustment and rapid spindle motor braking. • Coolant system with external collection tray. • External lubrication unit for automatic lubrication of all moving parts. • Complete segment holder (flange) with a set of segments + grinding wheel holder for diamond grinding wheel • Complete work area enclosure with sliding door • Work lights • Set of service wrenches • Documentation in French (1x printed, 1x on DVD) • CE Certificate Lubrication • External lubrication system for lubricating all moving parts. Watering System • Watering system including protective plates and hoses, including a settling tank outside the machine (without filter) Enclosure • Full enclosure with manually operated sliding door CNC Control LODI T2000 type CNC for managing and controlling the machine's axis movements. Automatic work cycle for grinding parts.

Condition: good (used), Year of construction: 1995, Machine-Details : Stock-No. 1022-2330 Type of machine Internal and Face Grinding Machine Make GLAUCHAU Type SIP 400x500 Year of manufacture 1995 retrofit Type of control conventional Storage location Monheim (Germany) Country of origin Germany Delivery time Immediately Freight basis Ex warehouse, loaded on truck Technical details : internal diameter 800 mm grinding depth 500 mm swing diameter 850 mm weight of the machine ca. 6,4 t Additional information : Used internal cylindrical grinding machine with face grinding device in special design with enlarged swing diameter Rjdpsx Nibpjfx Aa Eock and extended, hydraulic transverse movement Reconstructed and modernized 1995 in the Glauchau manufacturer’s plant, put into operation 1996 1. TECHNICAL DATA 1.1 Working area Grinding diameter in the workpiece guard internal grinding, min./max. mm 30/630(800) External grinding, max. mm 800 Grinding depth, up to approx. mm 500 Table stroke mm 800 Workpiece diameter, max. mm 800 Swing diameter in workpiece protection, max. mm 800 Without workpiece protection, approx. mm 850 Distance from workpiece spindle head to grinding spindle carrier, max. mm 1225 Adjustment of the internal grinding device on the table, max. mm 545 1.2 Workpiece headstock Cross shift, max. mm 650 Cross adjustment via gear motor and positioning device with HEIDENHAIN digital position display Swivel, max. degrees 15 Workpiece spindle Speeds rpm 16/22/32/ 45/63/90/ 125/18/250 Load capacity, max 1000 Spindle head (with bayonet flange) DIN 55021 size 11 Machine accessories: 2-axis digital displays made by HEIDENHAIN Coolant system with magnetic separator Fixators (machine shoes) Various grinding wheels Diamond dresser Large face plate Internal and face grinding device Halogen machine lamp Machine documentation

Year of construction: 2007, condition: like new (used), FICEP 601 DZB CNC DRILLING LINE with 4 way SCRIBING FACILITY I-Beams (without camber): Web height minimum 60mm maximum 610mm. Flange width minimum 30mm maximum 310mm. UNP Channels (web downwards): • Web height minimum 60mm maximum 610mm. Flange width minimum 30mm maximum 300mm. Angles • Flange height (unequal flanges as well) minimum 50 x 50 x 5mm maximum 250 x 250 x 40mm. Flats • Width minimum 100nn maximum 610mm. Square tubes • Size minimum 60 x 60mm maximum 300 x 300mm. Rectangular tubes • Size minimum 60 x 30mm maximum 600 x 300mm. Rsdpfxeh N Taae Aa Ejck All beams • Maximum thickness that can be drilled 50mm. Maximum length (infeed) 12000mm.

Year of construction: 2020, condition: new, We offer here a new shelf connector of the manufacturer Nedcon NS for sale. Included in delivery are: 01x SET Spacer NR new length: 200 mm Material colour: sendzimir galvanized consisting of each: 01x spacer NR L=200, sendzimir galvanized Rjdpfx Aaof S Iq Ts Ejck 02x hexagon head screw 8.8 M10x25 galvanized 02x Toothed nut, hexagonal 8.8 M10 flange galvanised 04x hexagon head screw, M10 galvanized

Condition: used, Technical details: grinding length: 12000 mm grinding width: 2800 mm workpiece height: 2510 mm max. workpiece weight: 24.000 kg table surface area: 11990 x 2500 mm distance between columns: 2820 mm cross rail adjustment: 2510 mm table feed: 1 - 40 m/min total power requirement: 110 kW weight of the machine ca.: 151 t dimensions of the machine ca.: 32,5 x 9 x 6,73 m .....machine is in top condition for high precision work! with CNC SIEMENS 840 D 1 universal grinding head, 22 kW swivelling of the grinding spindle +/-110° Rsdjwc A Snopfx Aa Eeck grinding wheel dimension 700 x 130 mm vertical stroke 1000 mm with dressing unit 1 surface grinding head, 30 kW grinding wheel dimension 600 x 150 mm vertical stroke 230 mm with dressing unit coolant and filtering unit diverse grinding wheel flanges *

Condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan shaft -Manufacturer: Elbe, cardan shafts with universal joint 4 pieces -Universal joint: Elbe .: 105 0 0 Rcsdpfxsxbb Ive Aa Eek - Flange Ø 58 mm -Bolt circle: Ø 47 x 5 mm -Dimensions: see photos / technical drawing -Shipping/Price: complete -Transport dimensions: 615/100/H60 mm -Weight: 2.8 kg

Condition: reconditioned (used), Year of construction: 2010, TECHNICAL SPECIFICATIONS, MODEL T 40.20 CN Grinding length mm: 400 Grinding width with grinding wheel width mm: 225 Grinding height with new grinding wheel (on magnetic chuck) mm: 280 Magnetic chuck surface mm: 400 x 200 Redsx N I A Ejpfx Aa Eeck Longitudinal travel mm: 500 Transverse travel of the carriage under the table mm: 220 Adjustable table speed m/min: 1-30 Grinding wheel dimensions mm: Ø225 x 25 x 51 Grinding wheel rotation speed, fixed rpm: 3,000 Automatic feed on the vertical axis, min. mm: 0.001 Spindle motor power 3 HP Hydraulic pump motor power 2 HP Net machine weight 1,500 kg - Vertical movement of the grinding wheel headstock The vertical movement is performed on SCHNEEBERGER linear needle slides and is controlled by a precision ball screw and a stepper motor. Vertical axis resolution: 0.001 mm. Dimension read on the display. Display resolution = 0.001 mm. Electronic handwheel for manual movement. - Transverse movement The sub-table carriage slides on SCHNEEBERGER linear needle slides. The transverse movement is controlled by a precision ball screw and a stepper motor. Dimension read on the display. Display resolution = 0.001 mm. Electronic handwheel for manual movement. - Longitudinal Table Movement A hydraulic cylinder and hydraulic unit located outside the machine control the table movement. VICKERS hydraulic pump SESINO air/oil heat exchanger for maintaining a constant hydraulic oil temperature Continuously adjustable table speed from 1 to 30 m/min. - Lubrication Centralized lubrication of all moving parts. - Paint Two-color paint: Safety white RAL 9003 + sky blue RAL 5015 ACCESSORIES - LODI CNC type T 2000 (see photo) - Automatic work cycle with different values ​​for the various phases of the cycle: roughing, finishing, polishing - Visualization to the thousandth of a millimeter of vertical and transverse axis movements - Electronic handwheel for manual axis movement - Coolant system with LOSMA type DTE paper filter external to the machine. - Air/oil heat exchanger for hydraulic oil temperature - SPD electropermanent magnetic plate with 5+5mm fine poles, dimensions 400x200mm - Automatic dressing device mounted above the head. Hydraulic movement – ​​micrometer increments (0.001mm resolution) via stepper motor - Programmable automatic dressing operations within the cycle, with automatic grinding wheel wear compensation - Hydraulic unit located outside the machine - Grinding wheel flange with balancing shaft and grinding wheel - Standard machine guards

Year of construction: 2000, condition: good (used), Technical Specification Punching/Shearing system Material * flatsteel length : 6.000 mm width : 50-500 mm thicknes : 5-30 mm * angle steel length : 12.000 mm width : 50 x 50 — 150 150 mm thickness : max. 15 mm Punching Machine VPO 1400 Capacity : 1400 kN (140T) Punch diameter/material thickness (max): 32 mm/25 mm Punching in flat- and angle steel : yes Number of punches for flat steel : 4 Number of punches for angle steel : 1 Hydraulic clamping : yes Centring points : yes Mist lubrication system : yes Shear for Flat Steel VPS 1800 Capacity : 1800 kN (180 ton) Width/material thickness (max) : 500 mm/22 mm Hydraulic clamping : yes Mitreshearing : +/- 45° Shear for Angle Steel VHS 1800 Capacity : 1800 kN (180 ton) Suitable for Angle : 50x50x5 up to and included 150x150x15 Hydraulic clamping : yes Punching Unit for Angle Flange Capacity : 600 kN (60 ton) Punchdiameter/material thicknes (max.) : 32 mm / 15 mm Numbering Unit Rjdoq Hu H Rjpfx Aa Eeck Number of disks : 4 pcs Number of characters : 36 pcs Character hight : 10 mm Number of characters per code : standard max. 16 Inprint : approx 1 mm Electrical power : 3 x 415V AC + N + PE, 50 CPS

Condition: good (used), Geared motor, electric motor, three-phase motor, electric geared motor -Speed: 18 rpm -Power: 0.75 kW -Shaft diameter: Ø 40 mm -Shaft length: 75 mm -Hole circle: Ø 215 mm -Outer flange: Ø 250 mm -Design: B5 -Protection class: IP 65 -Dimensions: 560/248/H300 mm -Weight: 43 kg Rsdpfoci N Ixex Aa Eock

Condition: refurbished (used), Year of construction: 2009, TECHNICAL SPECIFICATIONS, MODEL T 60.35 CN Rawable length mm: 600 Rawable width with grinding wheel width mm: 390 Rawable height with new grinding wheel (on magnetic chuck) mm: 400 Magnetic chuck surface mm: 600x300 Longitudinal travel mm: 750 Transverse travel of the carriage under the table mm: 350 Adjustable table speed m/min: 1-30 Gripping wheel dimensions mm: 400x40x127 Gripping wheel rotation speed, fixed rpm: 1,450 Automatic feed on the vertical axis, min. mm: 0.001 Spindle motor power: 7.5 kW Hydraulic pump motor power: 2.2 kW Net machine weight: 3,000 kg - Vertical movement of the grinding wheel headstock The vertical movement is performed on linear needle slides and is controlled by a precision ball screw and a YASKAWA brushless motor. Vertical axis resolution: 0.001 mm. Optical scale with 0.001 mm resolution. Dimension readout on the display. Display resolution: 0.001 mm. Electronic handwheel for manual movement. - Transverse movement The transverse movement is performed on hydrostatic slides and is controlled by a precision ball screw and a YASKAWA brushless motor. Dimension readout on the display. Display resolution: 0.001 mm. Optical scale with 0.001 mm resolution. Electronic handwheel for manual movement. - Longitudinal table movement Two hydraulic cylinders and a hydraulic unit located outside the machine control the table movement. Rotation speed is continuously adjustable from 1 to 30 m/min. Rcsdsx N I Arepfx Aa Eek - Lubrication Located outside the machine, this system controls the table movement and the lubrication of all moving parts. ACCESSORIES - LODI CNC type T 2020W with 12.1" graphic display (see photo) - Automatic work cycle with different values ​​for the various cycle phases: roughing, finishing, and polishing - Visualization to the thousandth of a millimeter of vertical and transverse axis movements - Electronic handwheel for manual axis movement - Coolant system with paper filter and high-pressure pump - Mist extractor (capacity 2,400 m³/h) - Electro-permanent magnetic plate, dimensions 600 x 300 mm - Hydraulic dressing device above the head with CNC-programmable automatic dressing operation and automatic grinding wheel wear compensation. - YASKAWA frequency converter for continuous adjustment of grinding wheel speed and for accelerating braking at rest. - Grinding wheel flange with balancing shaft - Complete work area enclosure - Work light

Condition: used, Year of construction: 2012, Maximum bar length..... 15 meters Maximum bar weight..... 300 kg/m Dimensions and profile types Punching 34 tons Shearing 130 tons Minimum Maximum Maximum in shearing IPE 80 200 200 IPN 80 200 200 Angles 35 x 3.5 120 x 12 120 x 12 UPE 80 200 200 UPN 80 200 200 UPAF 80 200 200 Flats 35 x 5 200 x 12 200 x 12 Redpfx Aaewum Tmo Eeck Maximum punching diameter (steel 400 N/mm²)..... Ø 32 mm in 8 mm thickness Maximum diameter in Maximum thickness (400 N/mm² steel) ..... Ø 22 mm in 12 mm thickness Number of punching diameters ..... 1 in the web and on the horizontal flange of the angles 1 in the reference flange on the vertical flange of the L and U sections 1 per half reference flange on the flange of the I and H sections

Condition: good (used), Magnetic plate, clamping plate, permanent magnet, magnetic chuck, magnetic chucking plate, permanent magnetic lathe chuck -Manufacturer: narex, magnetic clamping plate, permanent magnet chuck with chuck flange -Type: PERMAG K 250 Rcedpfev U Nwiox Aa Ejk -Clamping surface: Ø 250 mm -Recording dimensions: see photos -Dimensions: Ø 275 x 115 mm Total weight: 30 kg

Condition: refurbished (used), Year of construction: 2015, functionality: fully functional, TECHNICAL SPECIFICATIONS, MODEL RTR 600 CN Table diameter mm: 600 Electromagnetic chuck diameter mm: 600 Cross travel mm: 350 Max. grinding height with new grinding wheel mm: 400 Table speed, continuously adjustable rpm: 1-200 Gripping wheel dimensions mm: 400 x 50 x 127 Gripping wheel rotation speed, fixed rpm: 1,450 Automatic feed on the vertical axis, min. mm: 0.001 Spindle motor power kW: 15 Max. load on table kg: 1,000 Net weight approx. kg: 5,200 Vertical movement is achieved on linear slides and is driven by a precision ball screw and a YASKAWA AC motor. Rcjdpfxjx N I Alo Aa Eok Vertical axis resolution: 0.001 mm. Measuring system = encoder Dimension read on display. Display resolution = 0.001 mm. Electronic handwheel for manual movement. Transverse movement is performed on linear slides and is controlled by a precision ball screw and a YASKAWA AC motor. Transverse movement is performed by the grinding wheel head mounted on the cross slide. Transverse axis resolution = encoder Dimension read on display. Display resolution = 0.001 mm. Electronic handwheel for manual movement. Rotary table with hydrostatic circular slides. Infinitely variable rotation speed, with YASKAWA AC drive motor. Balanced hardened steel spindle with 15 kW motor. Fixed speed. Option: YASKAWA frequency converter for continuously variable spindle speed (1,100–1,900 rpm) Lubrication unit with automatic lubrication cycle, external to the machine, without initial filling. Standard accessories: - LODI CNC type T 2000 (see photo) - Automatic work cycle with different values ​​for the various cycle phases: roughing, finishing, flash grinding - Digital measurement of the vertical and transverse axes. Resolution = 0.001 mm - Electronic handwheel for manual axis movement - Continuously variable table speed via YASKAWA AC motor. Rotary table with hydrostatic slides - Grinding wheel headstock with 15 kW motor. Fixed spindle speed: 1,450 rpm. - Central lubrication for all moving parts - Hydraulic unit located outside the machine - Complete watering system with piping, electric pump, guards, electrical equipment, and a 250-liter settling tank (without filter) - Complete enclosure of the work area with sliding door (open ceiling) - 1 complete flange with grinding wheel - Work light - 1 set of service wrenches - CE Declaration of Conformity + CE plate - Operating voltage 400 V +/- 5%, 50 Hz - Electro-permanent magnetic plate with electronic device for adjusting the attraction force. WAGNER brand, type EP 360 - Ø 600mm - YASKAWA frequency converter for continuous adjustment of the grinding wheel speed (1,100-1,900 rpm) and for braking at the end of the cycle - LOSMA paper filter, type DTE 100 (capacity 300 liters) - LOSMA wet fume extractor, type AS1 (capacity 1,300 m³/h) - "MARPOSS" dynamic grinding wheel balancing device for dynamic and automatic balancing of the rotating grinding wheel - Linear diamond holder mounted on the grinding wheel headstock. Automatic dressing cycle with automatic grinding wheel wear compensation. Diamond increment by AC motor. Resolution 0.001 mm - 1 Diamond - Complete auxiliary pump for washing parts and the magnetic platen

Year of construction: 2007, condition: excellent (used), 603 LBH Technical Description Main Technical Specifications • Minimum sawing capacity at 90° min.mm 60 x 10 max.mm 610 x 310 • Sawing capacity at 45° mm 400 x 310 • Sawing capacity at 60° (available on two flanges only with relevant option) mm 250 x 250 • Mitering angles +45° / -60° • Toothed band size mm 34 x 1.1 Rodpfx Aajl Si Uus Eeck • Toothed band speed m/min. 78 • Band motor power kW 4 • Working level height mm 850

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint -Manufacturer: Elbe, Cardan shafts with universal joint Rjdpfx Aaox Ngike Ejck -Type: Length S/X 320/60 -Elbe .: 0.106.110.0001 -Flange Ø 65 mm -Bolt circle: Ø 52 x 6 mm -Dimensions: Ø 65 x 320 mm -Weight: 2 kg

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint -Manufacturer: Elbe, Cardan shafts with universal joint -Type: Length S/X 380/70 Redpfx Aasx Ngf Ee Ejck -Elbe .: 0.107.110.0001 -Flange Ø 75 mm -Bolt circle: Ø 62 x 6 mm -Dimensions: Ø 75 x 380 mm -Weight: 3.2 kg

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint -Manufacturer: Elbe, Cardan shafts with universal joint -Type: Length S/X 480/70 -Elbe .: 0.107. see photo -Flange Ø 75 mm -Bolt circle: Ø 62 x 6 mm -Dimensions: Ø 75 x 480 mm Redpfjx Nf Ufsx Aa Esck -Weight: 3.4 kg

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint -Manufacturer: Elbe, Cardan shafts with universal joint -Type: Length S/X 350/35 -Elbe item no.: 0.107. 100,0001 -Flange Ø 75 mm Rsdpfx Ajx Nf Tnoa Esck -Bolt circle: Ø 62 x 6 mm -Number: 6x cardan shafts available - Price: per piece -Dimensions: Ø 75 x 360 mm -Weight: 2.8 kg/pc.

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint -Manufacturer: Elbe, Cardan shafts with universal joint -Type: Length S/X 320/35 -Elbe item no.: 0.107. 100,0001 -Flange Ø 75 mm -Bolt circle: Ø 62 x 6 mm -Number: 6x cardan shafts available -Price: per piece -Dimensions: Ø 75 x 330 mm Rcsdpfx Ajx Nf R Toa Ejk -Weight: 2.7 kg/pc.

Year of construction: 2020, condition: good (used), Cardan shaft, universal joint, universal joint with flange, drive shaft, cardan joint Rcjdox Nf I Eepfx Aa Eok -Manufacturer: Elbe, Cardan shafts with universal joint -Type: Length S/X 350/40 -Elbe .: 9.990.000.0354 -Flange Ø 90 mm -Bolt circle: Ø 75 x 8 mm -Quantity: 10x cardan shafts available -Price: per piece -Dimensions: Ø 90 x 400 mm -Weight: 5.1 kg/pc.