Used Electronics Industry for sale (31,831)

Condition: new, Year of construction: 2025, Our SAPI "Mammut" pressure blasting unit with a 200-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Predpowc Rk Ejfx Ag Dsd Included in delivery: SAPI pressure blasting unit "Mammut 200 L" 1 1/4" pressure regulator, permanently mounted 1 1/4" water separator, permanently mounted SAPI safety shut-off Technical specifications of the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1 1/4" fixed piping inside and outside Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity: 200 l Total height: 1,420 mm Vessel diameter: 600 mm Total diameter: 1,000 mm Weight: approx. 140 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fastest start-up and shutdown times while maintaining compliance the regulations of the professional associations (VBG 48) The pressure setting can be precisely adjusted before blasting – continuously adjustable from 0.1 to 12.0 bar Lower abrasive consumption, as the pressure vessel remains permanently pressurized and there is no unnecessary run-on time Upon restart, full blasting pressure is immediately available at the nozzle – no pressure build-up necessary → lower consumption & less wear on the hose No condensate formation in the vessel, as it remains constantly pressurized → no venting or venting with every start/stop Optimal abrasive dosing with a hardened fine dosing valve Less compressed air required → noticeably lower diesel consumption One-person operation, as the pressure can be displayed and adjusted directly on the pressure gauge – even without starting No failure-prone components such as control valves, diaphragms, or seals → easy to maintain and reliable Only the blasting hose in the safety shut-off device needs to be checked and replaced if necessary

Condition: good (used), Rotary vane vacuum pump - oil lubricated Manufacturer: Leybold Type: Sogevac SV 300 Cat. No.: 10931 Status: Refurbished Warranty: 12 months Included: Oil filling (mineral oil), operating manual with list of initial files Voltage: 50/60Hz 230-400/460V Motor rating: 5,5 KW Final pressure without gas bellow: approx. 0,08 mbar Pedpobggb Ujfx Ag Dsrd Delivery time: ex stock

Condition: new, functionality: fully functional, A control electronics unit in its original packaging is for sale. Pedpfx Agswd Ebue Dsrd Please contact us if you are interested.

Condition: new, Industry diesel power generator J44 With AVR voltage regulator Generator IP23 | E-Start Engine type: John Deere | Fuel: Diesel Electr. power 3Ph: 44 kVA - 400 V Weight: 978 kg | Tank capacity: 100 liters Psdpjkyr I Sofx Ag Djrd Dimensions: LxWxH = 2,100 x 938 x 1,285 mm Equipment: - Connection via terminal strip - Control APM303 - Collecting tray for liquids - Soundproof body version Silent M137 - Support for short circuit current 2.7x In approx. 5 sec. - Pre-equipment/wiring for automatic/remote start - Measurement and display fuel level - Measurement and display of currents and power (integrated transformers) - AUTOMATIC accessories (battery charger + motor resistor) - Heat contact protection (CE requirement ISO 8528-13) - Sound insulation in accordance with 2000/14/CE standard - Soundproofing hood cpl. assembled (= version IV) - CE requirement Note the new color for the housing is CHARCOAL-BEIGE (RAL1014) SDMO dealer: Other models are available on request.

Condition: new, Year of construction: 2024, The INDUSTRY 2.0 ATC series differs from the standard series by using the best and most precise engines in its class and drive transmission, which significantly increase the machining capabilities of the machine, making it the most industrialized series in this price range. The INDUSTRY 2.0 ATC series CNC milling machine with a working surface of 2100x4000mm and a clearance in the Z axis of 300mm is equipped with a 9kW electrospindle and 24000 rpm on ceramic bearings. The machine's work table is made in hybrid technology - it has vacuum sections and subsections enabling automatic, non-invasive clamping of the processed material as well as T-slots allowing manual clamping of irregular shapes. ATC - The machine is equipped with an automatic linear magazine with a capacity of 8 tools. The automatic cutter changer does not require manual tool changing by the operator. Within one process, the machine can perform a multitude of operations such as surface planning, milling and drilling with various tools. Reinforced HEAVY DUTY construction - the machine body consists of profiles with a wall thickness of up to 10 mm. The frame is welded in its entirety, then subjected to a stress-relieving process in special conditions, and finally milled. This sequence of the process ensures the achievement of excellent results in stiffness, stability and vibration resistance. INDUSTRY 2.0 is a must-have in production plants requiring maximum machine efficiency. Worktable size - X - 2100mm, Y - 4000mm, Z - 300mm Drive - Leadshine servo drives with 1500W power and high holding torque (Double on the Y axis) Drive transmission - The most precise NIDEC SHIMPO planetary reducers Runner system - PMI 25mm linear guides and carriages with helical inclined strips with maximum contact surface Electric spindle - 9kW, 24000 rpm on full ceramic bearings Guide lubrication system - Automatic Tool length measurement system - Automatic Control system - NK-105 G3 controller Cables - Fireproof, adapted to bending and protected against deformation Manufacturer: TechnologieCNC Model: 2140 INDUSTRY 2.0 ATC Max. working speed in free passes: up to 33m/min Max. working speed in material: up to 25m/min Program resolution: 0.01mm Mechanical resolution: 0.04mm Standard CAD/CAM software: Artcam Open 2016 Optional CAD/CAM software: Vectric Cut 2D PRO (ramp entry function, automatic NESTING) - additional cost PLN 2,000 net Power supply: 3PH, 400V, 50-60Hz Prodpfxetvmcmo Ag Dsd A German vacuum pump BECKER VTLF 2.250 of the renowned BECKER brand with a capacity of up to 244m3/h is included in the standard equipment of the machine.

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 5350x4650x1820 mm Weight 7500 kg Psdpfjvz Hdyjx Ag Dsrd Total power requirement 47 kw

Condition: new, Our SAPI "Mammut" pressure blasting unit with a 60-liter tank capacity is suitable for all common blasting media. The blasting pressure can be continuously adjusted from 0.1 to 12 bar using the permanently installed pressure regulator. A water separator is also permanently installed on the blasting unit; this separates moisture from the compressed air and prevents the blasting media from clumping due to excessive moisture. Our safety shut-off device is included for safe operation of the sandblaster. This starts and stops the blasting process by operating the hand lever mounted on the blasting hose. Included in delivery: SAPI pressure blasting unit "Mammut 60 L" 1" pressure regulator, permanently mounted 1" water separator, permanently mounted SAPI safety shut-off Predpswc Afhjfx Ag Ded Technical specifications for the pressure blasting unit: Precisely adjustable from 0.1 - 12 bar TÜV-tested with certificate 1" fixed piping, internal and external Rubber-coated metal cone with rubber seal Generous hand hole Rubber-coated metal cone with rubber seal Large hand hole Rubber-wheeled chassis Abrasive dosing valve (suitable for all common blasting media) Capacity 60 l Total height 1,130 mm Bowl diameter 360 mm Total diameter 700 mm Weight approx. 60 kg ADVANTAGES OF THE SAPI PRESSURE BLASTING UNIT with safety shut-off Fast shut-off and start-up times, while complying with the regulations of the professional associations (VBG 48) Pressure setting Can be precisely adjusted before the actual blasting process, continuously adjustable from 0.1 to 12.0 bar. Reduced abrasive consumption, as the pressure vessel remains permanently pressurized, thus eliminating unnecessary abrasive run-on. Upon restart, the full blasting pressure is immediately available at the nozzle and does not need to be slowly built up. This significantly reduces abrasive consumption and significantly reduces wear on the blasting hose. No moisture (condensate) builds up in the vessel, as the vessel remains constantly pressurized and is not vented and vented with every start and stop. This process also offers other advantages, such as: Optimal abrasive dosing with a hardened fine dosing valve Lower compressed air consumption, thus significantly reducing fuel consumption (diesel) One-person operation, as the blasting pressure is constantly displayed by the vessel pressure and can be easily adjusted on the pressure gauge without prior start-up. No failure-prone components such as control valves, diaphragms, or seals, making it easy to maintain and reliable. Only the blasting hose needs to be checked in the safety shutoff and replaced if necessary.

Condition: like new (used), Year of construction: 2018, operating hours: 2,000 h, functionality: fully functional, machine/vehicle number: 10044/0218, !!! PHOTOS AND MORE INFORMATION CAN BE FOUND IN THE PDF DOCUMENT!!! !!! (PDF visible only on the PC website) !!! REASON FOR SALE: Machine purchased in 2018, operated until 2020, then decommissioned and preserved as a backup machine following the purchase of another CNC machine. DESCRIPTION: We offer a manual lathe Bezinger TLI 10 designed for producing wedding rings and specialized applications. The machine uses diamond tools for precision machining and achieving a perfect ring polish. It is capable of highly accurate machining of the inner, side, and outer surfaces of rings, including radii. Special separate fixtures enable individual operations without the need for adjustment or replacement of accessories. Psdpfx Agewi Iu Uo Dord - A unique feature of the lathe is the vacuum chip extraction via a vacuum cleaner hose (vacuum cleaner not included in the offer). - In addition to fixtures for gold processing, the machine also includes additive fixtures for manufacturing platinum rings. - The sales package includes sets of mandrels for inner clamping of rods and tubes in 4 different widths. Each set contains 40 sizes of mandrels. - Also included is a set of tools, see PDF attachment for details. Type: TLI 10 drive: 0.55 KW with electric brake speed: 0-1400 rpm tension: 380V; 50/60Hz dimensions: 100 x 70 x 130 cm weight: 170 kg

Year of construction: 2020, condition: new, 7 "Touch Panel The large color touch panel looks aesthetically and is comfortable and intuitive to use. You will set all important parameters on it. Memory of 20 programs with 10 events It is possible to save up to 20 programs and activate up to 10 consecutive time-temperature events arranged in the heating curve. This is especially needed for more demanding processes. Information on gas / oil consumption The consumption is calculated based on the burner settings. This feature will allow you to estimate the cost of a given cycle, plan consumption and check personnel. Dual-channel recorder of USB cycle parameters Each furnace is equipped with a recorder that records all firing parameters, including two temperature channels - like in an airplane black box, on a USB flash drive. Prjdpfx Asfz U Hveg Djd The system also enables the analysis of monthly / daily statements, including media consumption and performance. Each start of heating, opening the door, can be recreated, a few years back. Such a dedicated option is not offered by any manufacturer. It is a system developed from scratch by our programmers Automatic smoke exhaust chimney The chimney can be programmed to open a few minutes before the end of the firing in order to smoke the chamber. It can be remotely controlled from the panel, it does not need to be done mechanically as in most structures. Minute forecast until the end The cycle has started, how long will it end? calculating the heating dynamics, we will count it and show on the display how much longer it will take. To open it, just pull the door. The lock has adjustable pressure of the door, to close it just push it, the lock will catch the door and automatically pull it back. In order to minimize the effect of heating the hall when opening the door, a hood is installed above the door to remove some of the heat to other places. The MTS system was created to provide a real reading of the temperature of the furnace chamber. Standard measurement is based on one temperature measurement which is often wrong.MTS is a system of many sensors located in the outermost places of the chamber. The multi-zone heating system ensures a firing quality that has been so far unique. Each normal oven has only one heating zone and only one temperature measurement! The multi zone heat system supports up to 8 independent heating zones in one oven. Each heating zone has as many as 3 temperature sensors! When there are temperature differences between zones, they are automatically equalized! The system helps to combat the problem when elements of different material thicknesses enter the furnace.

Condition: new, Industry diesel power generator J88 Prjdpfx Ajkyr R Ueg Dsd With AVR voltage regulator Generator IP23 | E-Start Engine type: John Deere | Fuel: Diesel Electr. power 3Ph: 88 kVA - 400 V Weight: 1.530 kg | Tank capacity: 190 liters Dimensions: LxWxH = 2,572 x 1,126 x 1,571 mm Equipment: - Connection via terminal strip - Control APM303 - Collecting tray for liquids - Soundproof body version Silent M138 - Support for short circuit current 2.7x In approx. 5 sec. - Pre-equipment/wiring for automatic/remote start - Measurement and display fuel level - Measurement and display of currents and power (integrated transformers) - AUTOMATIC LIGHT accessories (battery charger + engine resistance predisposition) - Heat contact protection (CE requirement ISO 8528-13) - Soundproofing in accordance with 2000/14/CE standard - Sound insulation hood cpl. assembled (= version IV) - CE requirement Note the new color for the housing is CHARCOAL-BEIGE (RAL1014) SDMO dealer: Other models are available on request.

Condition: new, Year of construction: 2024, The INDUSTRY 2.0 series differs from the standard series by using the best and most precise engines in its class and drive transmission, which significantly increase the machine's machining capabilities, making it the most industrialized series in this price range. The INDUSTRY 2.0 series CNC milling plotter with a working surface of 1500x3000mm and a clearance in the Z axis of 300mm is equipped with a 6kW electrospindle and 24,000 rpm on ceramic bearings. The machine's work table is made in hybrid technology - it has vacuum sections and subsections enabling automatic, non-invasive clamping of the processed material as well as T-slots enabling manual clamping. Included with the Milling Machine Becker KVT 3.140 Vacuum Pump Manufacturer: TechnologieCNC Model: 1530 INDUSTRY 2.0 Electric spindle: 6kW, 24000rpm on full ceramic bearings Psdpfxotu S Srj Ag Derd Max. working speed in slow passages: up to 33m/min Max. working speed in the material: up to 25m/min Program resolution: 0.01mm Mechanical resolution: 0.04mm Working surface X/Y/Z: 1500x3000x300mm - Hybrid table (vacuum+T-slot) Control: NK-105 controller Achieving high working speeds and machining stability is guaranteed by the Leadshine EASY-SERVO servo drives used in the machine with an encoder and drive transmission via a SHIMPO planetary reducer Software: CAD/CAM as standard: Artcam Open 2016 Power supply: 3PH, 400V, 50-60Hz Dimensions: For transport - 365 / 210 / 220 Machine assembled and ready to work - 365 / 245 / 230 Hybrid table, i.e. vacuum table enabling non-invasive element fixing, leaving the possibility of manual fixing of irregular shapes The machine frame is fully welded, stress-relieved and then milled, which ensures machining accuracy and stability of work Machine control using the DSP NK-105 controller A tool height sensor is included A central oil lubrication system for trolleys and guides as standard The drive is transferred via a reducer The machine moves on high-class guides and PMI 25mm linear bearings in all axes (X, Y, Z) Double LEADSHINE Easyservo servo drive on the Y axis Machine wiring made of high-class fire protection cables. The electric cables used to build the milling machine are adapted to bending and are protected against deformation

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 4850x4650x1820 mm Weight 6500 kg Prodpjvz E R Ssfx Ag Dod Total power requirement 47 kw

Condition: new, SDMO Industry Diesel Generator J22 With AVR voltage regulator Generator IP23 | E-Start Engine type: John Deere | Fuel: Diesel Electr. power 3Ph: 22 kVA - 400 V Weight: 922 kg | Tank capacity: 100 liters Dimensions: LxWxH = 2,100 x 938 x 1,285 mm Equipment: - Connection via terminal strip - Control APM303 - Collecting tray for liquids - Soundproof body version Silent M137 - Support for short circuit current 3x In approx. 10 sec. - Pre-equipment/wiring for automatic/remote start - Measurement and display fuel level Prjdpfxskyr Hxe Ag Ded - Measurement and display currents and powers (integrated transformers) - AUTOMATIC accessories (battery charger + motor resistor) - Heat contact protection (CE requirement ISO 8528-13) - Soundproofing in accordance with 2000/14/CE standard - Soundproofing hood cpl. assembled (= version IV) - CE requirement Note the new color for the housing is CHARCOAL-BEIGE (RAL1014) SDMO dealer: Other models are available on request.

Condition: new, Year of construction: 2024, CNC 1212INDUSTRY 2.0 6kW 1200x1200 milling machine with Becker KVT 3.140 vacuum pump The INDUSTRY 2.0 series differs from the standard series by using the best and most precise engines in its class and drive transmission, which significantly increase the machining capabilities of the machine, making it the most industrialized series in this price range. The INDUSTRY 2.0 series CNC milling plotter with a working surface of 1200 x 1200 mm and a clearance in the Z axis of 300mm is equipped with a 6kW electrospindle and 24,000 rpm on ceramic bearings. The machine's work table is made in hybrid technology - it has vacuum sections and subsections enabling automatic, non-invasive clamping of the processed material as well as T-slots enabling manual clamping. Technical data: Manufacturer: TechnologieCNC Model: 1212 INDUSTRY 2.0 Electric spindle: 6kW, 24000rpm on full ceramic bearings Max. working speed in free runs: up to 33m/min Max. working speed in the material: up to 25m/min Program resolution: 0.01mm Mechanical resolution: 0.04mm Working surface X/Y/Z: 1200x1200x300mm - Hybrid table (vacuum + T-slot) Control: NK-105 G2 controller Achieving high working speeds and machining stability is guaranteed by the Leadshine EASY-SERVO servo drives used in the machine with an encoder and drive transmission via a SHIMPO planetary reducer Software: CAD/CAM as standard: Artcam Open 2016 Power supply: 3PH, 400V, 50-60Hz Weight: approx. 650kg Dimensions: For transport - 220 / 190 / 220 Machine assembled and ready to work - 220 / 225 / 230 Standard equipment Hybrid table, i.e. vacuum table enabling non-invasive fixing of the element, leaving the possibility of manual fixing of irregular shapes The machine frame is fully welded, stress-relieved and then milled, which ensures machining accuracy and stability of work Podpfstu H Tujx Ag Djrd Machine control using the DSP NK-105 controller Tool height sensor included Central oil lubrication system for trolleys and guides as standard equipment Drive transmission is carried out via a reducer The machine moves on high-class guides and PMI 25mm linear bearings in all axes (X, Y, Z) Double LEADSHINE Easyservo servo drive on the Y axis Machine wiring made of high-class fire protection cables. The electric cables used to build the milling machine are adapted to bending and are protected against deformation

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 5350x4380x1820 mm Weight 6800 kg Pedpfx Agovz E R Es Dord Total power requirement 41 kw

Condition: new, Year of construction: 2024, The INDUSTRY 2.0 series differs from the standard series by using the best and most precise engines in its class and drive transmission, which significantly increase the machine's machining capabilities, making it the most industrialized series in this price range. The INDUSTRY 2.0 series CNC milling plotter with a working surface of 1300x2500mm and a clearance in the Z axis of 300mm is equipped with a 6kW electrospindle and 24,000 rpm on ceramic bearings. The machine's work table is made in hybrid technology - it has vacuum sections and subsections enabling automatic, non-invasive clamping of the processed material as well as T-slots enabling manual clamping. Hybrid table, i.e. vacuum table, enabling non-invasive fixing of the element, leaving the possibility of manual fixing of irregular shapes The machine frame is fully welded, stress-relieved and then milled, which ensures machining accuracy and stability of work Machine control using the DSP NK-105 controller Tool height sensor included Central oil lubrication system for trolleys and guides as standard Drive transmission is via a reducer The machine moves on high-class guides and PMI 25mm linear bearings in all axes (X, Y, Z) Double LEADSHINE Easyservo servo drive on the Y axis Machine wiring made of high-class fire protection cables. The electric cables used to build the milling machine are adapted to bending and are protected against deformation Manufacturer: TechnologieCNC Model: 1325 INDUSTRY 2.0 Electric spindle: 6kW, 24000 rpm. on full ceramic bearing Prsdstu I Hujpfx Ag Dsd Max. working speed in slow passages: up to 33m/min Max. working speed in the material: up to 25m/min Program resolution: 0.01mm Mechanical resolution: 0.04mm Working surface X/Y/Z: 1300x2500x300mm - Hybrid table (vacuum+T-slot) Control: NK-105 Controller Achieving high working speeds and machining stability is guaranteed by the Leadshine EASY-SERVO servo drives used in the machine with an encoder and drive transmission via a SHIMPO planetary reducer Software: CAD/CAM as standard: Artcam Open 2016 Power supply: 3PH, 400V, 50-60Hz For transport - 307 / 190 / 220 Machine assembled and ready to work - 307 / 225 / 230

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 4850x4380x1820 mm Psdpfx Ajvz E Htog Dord Weight 5800 kg Total power requirement 41 kw

Year of construction: 1988, condition: good (used), Bucket sealer Make: Soft Electronic Systems Type: Semi-automatic bucket sealer Model: PMS 2 GH Capacity: Up to 300 buckets per hour Frame: Stainless steel Range: Buckets up to D = 300mm Dimensions: L x B x H = 1.000 x 900 x 1.000 mm Weight: 150 Kg Pjdpfxoigyp He Ag Djrd Power supply: 380 Volt – 50 Hz – 1,5 kW Comp. Air: > 5.5 Bar Features: manually positioning of bucket automatic seal process (adjustable time) automatic sliding towards cutting device automatic pushing and rotating knife manually reeling up the film manually removing of bucket

Condition: as good as new (ex-display), functionality: fully functional, grinding height: 200 mm, power: 11.03 kW (15.00 HP), grinding belt speed: 18,000 mm/s, grinding belt length: 2,620 mm, grinding belt width: 1,370 mm, input frequency: 50 Hz, input voltage: 400 V, Additional technical data Feed speed: 2.8 - 20 m/min The new Format4 findustry wide belt sanders impress in industrial applications primarily through their individually configurable assembly of units. Tailored specifically to the application and field of use, the machine can be equipped with two, three, or four units. A high degree of customization guarantees that all requirements in terms of surface finish and processing efficiency are met. Maximum operating comfort in industrial applications The clearly structured touchscreen control panel is intuitive to operate. All machine functions are clearly displayed graphically on the digital display. The pass-through thickness can be set directly from the control panel to a tenth of a millimeter at the touch of a button. Automatic thickness measurement simplifies the adjustment of the machine to the desired workpiece thickness. The workpiece can be measured without additional measuring devices, and its thickness is then transmitted directly to the machine "wirelessly." The fixed infeed table height of 900 mm allows for easy and fatigue-free operation, while a vacuum table, roller table extensions on both infeed and outfeed sides, as well as optional pressure shoes on the sanding units, ensure maximum comfort and optimal processing conditions for workpieces of any size. Optional equipment 10E LACQUER – Cross sanding unit ESC in place of 1st contact roller 20A 2nd contact roller unit 22 2nd sanding roller in 85° Shore 30E LACQUER – Superfinish unit ESC in place of 3rd contact roller 39 Switch contact for slide control (price/piece) *6 51 Soft start for 15kW (20HP motor) 59B Control unit with 15" color touchscreen display 63 Scotch-Brite brushing device at the machine outfeed 71 Oscillating cleaning blower for workpiece and conveyor belt 72 Ionizing bar at the machine outfeed 73 Vacuum table with 4kW (5.5 HP) blower 74 Inverter for vacuum blower for vacuum adjustment 83 Sanding height 200mm instead of 170mm Pedpfxsxtpyde Ag Djrd 84 Optimized control software for special processing 87 ESC workpiece detection sensor with 50 segments 201 2nd motor with 15kW power output Additional information Workpiece height: 3 - 170 mm Constant infeed height - fixed table: 900 mm Grooved sanding roller: Ø 250 mm Including delivery and installation in post code areas 71, 72, 73, 77, 78, 79, 86, 87, 88, 89

Condition: good (used), Year of construction: 2003, Plasma cutting machine, plasma cutter for plasma cutting system, plasma/oxygen cutting system, servo motor, gear motor Prsdpfx Aewkqmiog Dod -Manufacturer: CR Electronic SRL / Power Automation, servo drive for plasma/oxygen cutting system -Cutting system: Type OXY 5.1 - 25 -Servo motor: Power Automation type PAT3B-S4-SRM50 -Individual components: see photos -Number: 2x drive unit available -Price: per unit -Dimensions: 475/240/H140 mm -Weight: 12.4 kg/pc.

Condition: new, The DP-700Industrie is the industrial version of our multi-blade circular saw in an extra robust design. It is specially developed for the industrial longitudinal division of materials. It was designed to efficiently process large quantities of material. The independent positioning of two saw blades and the ability to install multiple fixed discs make this machine ideal for processing hardwood at different heights. This means it is designed for long-term use in the production of lumber, pallets or other wood cut goods. The machine is equipped with an upper and lower extraction device to ensure maximum extraction performance, which solves a common problem with multi-blade circular saws. 9 pieces of 140mm thick feed rollers - 6 pieces at the feed, 3 pieces behind the saw blades - pull in every workpiece quickly and easily. The scope of delivery includes 10 saw blade holders, which can be moved anywhere on the shaft. Technical data: Prsdpfevrvgxjx Ag Ded Motor power: 30 kW Feed motor power: 1.1 kW Shaft diameter: 70mm Saw blade diameter: 450 mm Maximum cutting height: 150 mm Minimum material length: 800 mm Saw blade speed: 3500 rpm Feed speed: 6 - 35 m/min (infinitely adjustable) Material width: max 650 mm Width of feed rollers: 600 mm Measurement: with scale Saw blade holders included: 10 pieces Weight: approx. 3,000 kg Optional: More powerful motor (up to 50 kW) Interchangeable saw bushings Longer rolling table (4 meters long) Additional saw blade holders

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: 516221V01776, Year of construction: 2019, operating hours: 4,964 h, load capacity: 1,600 kg, lifting height: 4,660 mm, free lift: 1,510 mm, mast type: triplex, Equipment: CE marking, TECHNICAL DETAILS Lifting capacity: 1,600 kg Lift height: 4,660 mm Free lift: 1,510 mm Overall height (overhead clearance): 2,060 mm Mast type: Triplex Maximum fork width: 800 mm Prjdpfsxw S Ekjx Ag Djd Minimum fork width: 0 mm Fork dimensions: 1,200 mm x 800 mm Fork length: 1,200 mm MACHINE DETAILS Number of wheels: 3 Dimensions & Weight Dimensions (L x W x H): 1,950 x 1,150 x 2,060 mm Weight: 3,206 kg Electrical data Battery year: 2019 Capacity: 625 Ah Battery voltage: 48 V Operating hours: 4,964 h EQUIPMENT CE marking Side shift Weighing system Free lift New battery Non-marking tyres

Condition: ready for operation (used), Year of construction: 2004, functionality: fully functional, machine/vehicle number: 10651-7, travel distance X-axis: 600 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 300 mm, table load: 800 kg, spindle speed (max.): 42,000 rpm, TECHNICAL DETAILS Travel X-axis travel: 600 mm Y-axis travel: 450 mm Z-axis travel: 300 mm Rapid traverse X-axis rapid traverse: 30 m/min Y-axis rapid traverse: 30 m/min Predsxvybdjpfx Ag Djd Z-axis rapid traverse: 30 m/min Work Table Table width: 405 mm Table height: 405 mm Table load capacity: 800 kg Rotary table diameter: 405 mm Spindle Maximum spindle speed: 42,000 rpm Spindle taper: HSKE40 Number of tool magazine pockets: 26 MACHINE DETAILS Control model: RMS6, Version 3.18 Dimensions & Weight Dimensions (L x W x H): 4,210 x 2,350 x 2,600 mm Weight: approx. 7,000 kg Input voltage: 400 V EQUIPMENT Documentation/manual Continuously variable spindle speed Chip conveyor Blum laser 3D tool probe Hirschmann 9000 zero-point clamping system Electronic handwheel Extor extraction unit

Condition: ready for operation (used), Year of construction: 2018, functionality: fully functional, spindle speed (max.): 3,000 rpm, travel distance X-axis: 90 mm, travel distance Y-axis: 80 mm, travel distance Z-axis: 400 mm, spindle bore: 40 mm, TECHNICAL DETAILS Travel Distance X-axis: 90 mm Travel Distance Y-axis: 80 mm Travel Distance Z-axis: 400 mm Maximum Admissible Head Circle Diameter: 140 mm Milling Arbor Diameter: 22 mm Maximum Gear Cutting Length: 160 mm Angle Maximum Milling Head Swivel Angle +A Direction: 45° Maximum Milling Head Swivel Angle -A Direction: 118° Workpiece Spindle Outer Diameter: 105 mm Bore: 40 mm Rapid Traverse X-axis: 7,500 mm/min Y-axis: 5,000 mm/min Z-axis: 15,000 mm/min Speeds Tool: 50 to 4,000 rpm Maximum Workpiece Spindle Speed: 3,000 rpm MACHINE DETAILS Electrical Connection Podpfx Aoxvrarog Djrd Mains Connection: 400 V (AC) Supply Voltages: 400 V (AC) Control Voltage: 24 V (DC) Frequency: 50 Hz Machine Connected Load: 13 kVA Cable Cross-section: 16 mm² Protection: 63 A Dimensions & Weight Space Requirement: 5.25 x 4.06 x 2.94 m Machine Weight: 8 t EQUIPMENT Industrial Filter IFS EC1500 Sediment Separator Knoll KF200/640 Integrated Chip Conveyor with Magnetic Separator Machine Automation for Loading and Unloading Workpieces Robot Automation Güdel KTB-31/62, Year of Manufacture: 2018 with Station for Part Removal

Condition: ready for operation (used), functionality: fully functional, machine/vehicle number: FN491966, Year of construction: 2015, operating hours: 15,963 h, load capacity: 2,500 kg, lifting height: 5,030 mm, free lift: 1,630 mm, mast type: triplex, fork width: 350 mm, TECHNICAL DETAILS Mast: Triplex Lifting capacity: 2,500 kg Lifting height: 5,030 mm Free lift: 1,630 mm Overall height: 2,290 mm Fork dimensions: 1,000 mm x 1,000 mm Minimum fork width: 350 mm MACHINE DETAILS Number of wheels: 4 wheels Electrical Data Prsdpfexw Slqjx Ag Djd Drive: Electric Capacity: 775 Ah Battery voltage: 80 V Dimensions & Weight Dimensions (L x W x H): 2550 cm x 1200 cm x 2290 mm Unladen weight: 4,555 kg Year of battery manufacture: 2018 Operating hours: 15,963 h EQUIPMENT Half cab Work lights Non-marking tires Free lift Joystick Attachment: Fork positioner Side shift