Used Double Column Mill for sale (22,796)

Condition: used, Year of construction: 1991, pressure 400 t stroke 300 mm table surface area 1200 x 700 mm ram surface 1200 x 700 mm dayligth 500 mm adjustment of stroke 300 mm return capacity 348 kN capacity of ejector 100 kN ejector stroke 100 mm control SIEMENS Simatic S 5 total power requirement 65 kW weight of the machine ca. 28 t dimensions of machine L x W x H 4,4 x 2,75 x 4,0 m Hedjtqqlcopfx Ac Tet = hydr. punching and embossing press Accessories: tool changing table - with cutting shock absorption damping force 4000 kN damping stroke 5 mm spindle adjustment 200 m

Condition: as good as new (ex-display), Year of construction: 2023, pressing force: 120 t, table length: 600 mm, table width: 600 mm, Here are the technical data of the offered machine: Technical data + information: HB 2021-A-188, oil hydraulic double column press 120 T bottom piston heating press. - idle speed up to 40 mm/sec - Opening speed up to 40 mm/sec - Starting press speed 5-15 mm/sec - Table size/heating plate size 600 × 600 mm Hsdpfx Acjk S Dt Tj Tet - ram size/heating plate size 600 × 600 mm - 2 heating plates, electrically heated, up to 250 degrees - as OPTION - total size approx. 2000 × 1000 × 2800 mm height - Oil temperature control - Automatic lubrication - Free positioning of the ram - SICK/LEUTZE light barriers 14,1 mm on front side - Circuit oil cooling - Pressure holding valve 0 to 1800 sec. - Rear monitored door - Pressure adjustment from 30 T to 120 T - Travel limitation either by pressure or position - Programming set-up mode, single stroke (adjustable via rotary switch) - Control panel permanently installed in cabinet wall - Two-hand operation - Machine body double painted - Signal light: red: alarm, yellow baking phase, green: ready - Heating plates with electric heating rods, up to max. 250 degrees - Assembly, commissioning, instruction against separate charge Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 1,600 kN Free ripping force max. 200 kN Pressure build-up time closed die steel to steel Max. 8 sec. Dimensions Max. Opening width per compartment 200 mm Stroke and min. opening per compartment 400/200 mm Table height above floor, without heating pl. 850 mm Height above floor (overall height) approx. 2.800 mm Hall height min. 3,500 mm Parallel deviation at 20 °C +/- 0.1 mm Deflection Determined at max. clamping force with 70 % occupancy ≤ 0.2 mm/m Total weight of the press without operating materials approx. 9 to Accessories: 4 HEATING PLATES 500 × 400 mm, max. heating capacity Equipped with temperature sensor 300 degrees Speeds Fast closing with 15 mm sec. Pressing speed 10 mm sec. Sound pressure level, measured at 1.5 m height at the control panel according to DIN 45635-T16-KL3 max. 8 db(A) Number of pressing cylinders 1 pc. Operating pressure max. 240 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 5 bar Main pump BOSCHREXROTH gear pump approx. 48 L/min Oil volume approx. HLP 46 MW 300 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Automatic pressure readjustment after 5 % pressure loss Pressure stabilization for up to 1800 sec. Electrical system Main supply 400 V AC Control voltage Hydraulic pumps 24 V DC 24 V DC Frequency 50 Hz Connection hydraulic main motor 15 kW Total connection approx. without heating plates 19 kW ##### If the press does not exactly meet your requirements, please click to request an individual offer exactly according to your needs: Contact us for an individual offer HIDROBRASIL manufactures presses exactly according to your requirements at surprisingly low prices! Our great strength is special machine construction and press automation. We sell customized hydraulic presses, press brakes and impact shears at surprisingly low prices. For the hydraulics of the presses we mainly use components of leading European manufacturers.

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 550 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Hjdpfjfxygpjx Ac Tot Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,3 t dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? :1200 ? :1200 ?

Condition: used, Year of construction: 2001, functionality: fully functional, travel distance X-axis: 6,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 1,700 mm, feed length X-axis: 5,700 mm, feed length Y-axis: 1,000 mm, feed length Z-axis: 1,700 mm, position of the milling head: Testa birotativa A+B 1° + 3°, rapid traverse X-axis: 20 m/min, rapid traverse Y-axis: 20 m/min, rapid traverse Z-axis: 20 m/min, spindle speed (max.): 4,000 rpm, table length: 7,300 mm, table width: 1,090 mm, spindle motor power: 30 W, Equipment: documentation/manual, rotational speed infinitely variable, - FIDIA C20/H6 numerical control - Electronic handwheel - Operator platform - Spindle cooling system Hsdjzix Rwspfx Ac Tst - 24-position tool magazine - 3 longitudinal tables, 1520 x 1000 x 900 mm - Splash guard enclosure - CE marking

Condition: used, Year of construction: 1997, Technical details: Hodpsu Nfmmsfx Ac Tjt pressure: 160 t distance between columns: 1000 mm stroke: 250 mm dayligth: 600 mm distance table/ram: 600 mm table height over floor: 550 mm table surface area: 810 x 860 mm clamping surface ram: T x B: 720 x 580 mit T-Nuten mm total power requirement: 15 kW weight of the machine ca.: ca. 16,0 t The machine isn't installed yet. The pictures are from the origin location of the former owner. further details: - sideway passage W: 520 x H: 620mm - passage front side W:660mm x H: 600mm equipment: - walkable platform arround the machine= height over floor approx. 2400mm, platform approx. 2700 x 2600 x 1050mm - hydraulic pack - oil cooler i.D. *

Condition: used, Technical details: pressure: 63 t throat: 315 mm ram adjustment: 60 mm adjustment of stroke: 70 mm ram stroke: 10 - 105 mm no. of strokes: 71 - 140 Hub/min strokes per minute: Einzelhub: 45 / 50 Hub/min. passage between the side columns: 355 mm dayligth: 335 mm table:: BxT: 800 x 630 mm passage opening in table: 400 x 130 mm clamping plate: BxT: 616 x 85 mm clamping surface ram: BxT: 450 x 280 mm mortise hole in ram: Ø 50 x 83mm mm total power requirement: 7,5 kW weight of the machine ca.: 5,9 t dimensions electric cabinet LxWxH: 0,86 x 0,30 x 1.3 m dimension machine xH: Presse: 1,42 x 1,8 x 2,6 m Press with roll feed/strip system and straightener Hsdpfx Ajvt Nvpsc Tst High-performance press with roll feed/strip system and straightening machine Application: suitable for series production Equipped with servo roll feed MINI: refurbished until 01/2021 -manufacturer P/A GmbH, type SRF 220 -for strip width 220mm -feed rate 150m/min. -operation with hand tool straightening system: -manufacturer Wanzke, type KS 150 -insertion width max. 200mm -2 pieces driven inserting rolls -4 pieces driven straightening rolls (top), adjustable vertical approx. 30mm -5 pieces driven straightening rolls (bottom), fixed, not adjustable Coil = special design: -mechanical/manual -external take-up max. Ø 1.500mm -internal take-up max. Ø 300mm -width max. 200mm Roller deposit: -roller system with 9 pieces of roller bars with 53 rollers (Ø 25x25mm). *

Condition: used, Year of construction: 1990, Technical details: Pressure: 63 t distance between columns: 200 mm stroke: 150 mm dayligth: 430 mm no. of strokes: 400 Hub/min Hedpou Icxqofx Ac Tst T-slots H 12 650: 18 mm hole in table: 420x160 b x l mm ram surface area: 650 x 450 mm control: Wanske Tronicpress CNC passage of columns: 550x540 mm tank: 200 l stroke of ram - fixed: 100 mm ram diameter: 40 mm table height over floor: 1000 mm table: 600x450 mm table height over floor with metal base stand: 880 mm total power requirement: 30 kW weight of the machine ca.: 3,9 t Hydraulic automatic punching press for precision work (high-speed press) - for punching, drawing, pressing, minting, bending, riveting, straightening, assembling - with hydraulic gripper feed type HS 150 and 7-roller straightener (moving) - Normal strips of approx. 0.4mm - 2.5mm thickness x approx. 160mm width, as well as narrow strips up to approx. 4mm can be processed. Feed length can be adjusted as required via the control unit. - with ram round column guide - with automatic central lubrication - High-speed: up to 400 strokes min-1 - motorized adjustable fixed stop (bottom can be adjusted by hand/motorized) - Operating modes such as continuous stroke and/or single stroke Equipment: - 1x hydraulic unit - 2x control cabinets *

Condition: used, Year of construction: 1964, Technical details: pressure: 125 t stroke: 28 mm number of strokes: 56-225 Hub / Min distance between columns: 1000 mm ram adjustment: 60 mm Hodpfx Aju Nfibec Tst distance table/ram: 376 mm Table dimensions: B.950xT:720 mm passage opening in table: 400x130 mm height over floor: 1120 mm ram surface area: 920x540 mm mortise hole in ram: Dm 65 x 120 mm column travel -side: 250 mm total power requirement: 30 kW weight of the machine ca.: 15,5 t dimensions of machine: 3,1x1,34x3,6 m dimensions electric cabinet LxWxH: 0,64x0,22x1,2 m This press is a high-performance press for mass production /series production. - Contains left side a material feed via automatic feed (mechanic) and right side a waste cutter. Feed = 0-200mm, roll width =250mm Partial documentation as a copy available. Machine is not functional and is on sale as is! *

Condition: used, Technical details: pressure: 80 t distance between columns: 880 mm dayligth: 200 mm Table dimensions: 880x300 mm height over floor: 1000 mm distance between columns: 800 mm total power requirement: ca. 12 kW machine weight ab.: 2855 kg space requirements of the machine approx.: T:1,4xB:1,65xH:1,9 m Embossing - Hot Embossing application area: - for example: for foils, plastics, paper, hardboard materials etc. - stamp plate size: 600x310mm equipment: Hjdpfx Acju Icwto Tjt - counter - hydr. tank Accessories: - Mounting plate (600x300x90mm) not heatable. Sale as is. *

Condition: used, Technical details: pressure: 80 t dayligth: 600 mm ram stroke: 200 mm Hjdpfju Nfnwsx Ac Tot pressure: 30 t dayligth: 680 mm ram stroke: 300 mm distance between columns: 1060 mm base plate surface area: 1060x600 mm table above floor: 720 mm ram stroke speed: Stößel/ Ram 1: 40 mm/sec ram stroke speed: Stößel/ Ram 2: 95 mm/sec base plate surface area: Dm=150 mm total power requirement: 13 kW weight of the machine ca.: 4,5 t space requirement approx.:: L:1,6xB:1,1xH:3,4 m - Press with two ram with 30 t + 80 t - foot control - documentation *

Condition: used, Year of construction: 1985, Technical details: pressure: 100 t no. of strokes: 35-100 Hub/min throat: 360 mm ram adjustment: 20-130 mm ram surface area: 750x550 mm clamping plate on table: 1000x640 mm adjustment of stroke: 90 mm passage between the columns longitudinal/sideways: 610x500 / 440x550 mm daylight dimension : table/slide low: 300 mm total power requirement: 17,5 kW Hodpfxeu Nfh De Ac Tjt weight of the machine ca.: ca,7,0 t dimension machine xH: 1,9x1,4x2,7 m - there are 5 T-slots lengthwise on the ram plate - centre hole = 50mm This press is currently for sale without controls. Optional on customer request completion possible. i.D. *

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressing force: 160 t, table length: 550 mm, table width: 500 mm, working height: 700 mm, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :600 mm Ram plate:700 x 600 mm table height over floor:850 mm Table size:700 x 600 mm speed of forward flow:10 mm/sec Pressing speed:10 mm/sec :10 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,2 t dimensions:950 x 2440 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück heating plates :550 x 500 mm :6800 ? :2400 ? :1200 ? Hedpfxsfxyh Rs Ac Tst :1200 ?

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, travel distance X-axis: 16,000 mm, travel distance Y-axis: 1,600 mm, travel distance Z-axis: 4,000 mm, rapid traverse X-axis: 30 m/min, rapid traverse Y-axis: 30 m/min, rapid traverse Z-axis: 30 m/min, spindle speed (max.): 5,000 rpm, CNC SIEMENS 840 D WORKING AREA Longitudinal travel X axis: mm 16.000 Cross travel Z axis: mm 1.600 Vertical travel Y axis: mm 4.000 Rapid traverse rate: m/min 30 Axis acceleration: m/s² 2 Maximum axis thrust: N 16.000 WORKING TABLES No. 2 floor plates: mm 7.792 x 3.190 Rototranslating table: mm 3.000 x 2.992 Cross travel of rototranslating table: mm 2.500 Maximum load capacity at table center: Ton 60 SPINDLE Tool taper: ISO 50 DIN 69871 Spindle speed: Rpm 5.000 Power S1: kW 37 Power S6: kW 56 Maximum torque S1: Nm 1.295 Maximum torque S6: Nm 1.963 Usable low range: Rpm 0 – 1.145 Usable high range: Rpm 1.145 – 5.000 KOSMO 3 UNIVERSAL MILLING HEAD Positioning accuracy: ± 0.002° Maximum torque on rear plane: Nm 15.600 Hjdpfxozipmpe Ac Tjt Maximum torque on front plane: Nm 11.000 Lubrication and cooling: Forced oil circulation Weight: kg 450 EQUIPMENT • Rueckle rototranslating table, size 3,000 x 2,992 mm, cross travel 2,500 mm, maximum load capacity at table center 60 tons, equipped with double preloaded pinion system; • Vertical axis designated as Y and cross axis designated as Z; • Remote electronic handwheel; • Automatic universal bi-rotary milling head “KOSMO 3 5000”, 5,000 rpm, ISO 50, indexing 0.02° on the front plane, continuous C-axis (hydraulic clamping) and 1° Hirth coupling on the rear plane, oil recirculation lubrication system; • Horizontal extension, diameter 200 mm, length 600 mm, 4,000 rpm, ISO 50 taper, continuous C-axis (hydraulic clamping) and 1° Hirth coupling; • Continuous platform (C-axis) prepared for future installation of a 2-axis continuous milling head; • Automatic head changer for the above-mentioned heads (Kosmo head, horizontal extension and preparation for continuous head); • Head storage magazine for 2 heads (Kosmo head + horizontal extension); • Air conditioning unit for electrical cabinet; • Belt-type chip conveyor along X-axis complete with transverse conveyor, coolant tank and coolant pump; • High-pressure coolant system, 40 bar through spindle, complete with tank and paper filter system, DIN 69871 type B; • Chain-type tool magazine with 80 positions “MAC80”, ISO 50, with tool change capability in both horizontal and vertical spindle positions (maximum tool length 400 mm, maximum tool weight 20 kg); • Air blast through external spindle nozzle; • Renishaw NC4 laser tool presetting system; • Renishaw RMP60 workpiece probe; • Mobile operator cabin moving along vertical and horizontal axes; • Instruction manuals and CE Declaration of Conformity.

Condition: used, Year of construction: 2013, Technical details: x-travel: 30000 mm y-travel: 3600 mm z-travel: 1900 mm milling head speed: 1 - 4000 U/min Hodpfxovmziho Ac Tot spindle taper ISO: 50 feed speeds: 1 - 10000 mm/min rapid traverse: 25 m/min milling spindle motor: 46 kW total power requirement: 85 kW dimensions of the machine ca.: 45 x 8,7 x 5,5 ü.F. m with CNC HEIDENHAIN iTNC 530 autom. milling head indexing 2,5° floor plate field 31000 x 2500 mm ( 4 floor plates 6000 x 2500 mm + 1 floor plate 7000 x 2500 mm ) 2 chip conveyors, coolant attachment *

Condition: used, Year of construction: 2009, faceplate diameter 3000 mm swing diameter 3500 mm turning height 3200 mm Control Fanuc type Series 320i Model A slide adjustment 1750 mm ram head dimension 300x300 mm x-axis 2700 mm Table load 30000 kg main drive motor 100 kW Tool changer 16 weight of the machine ca. 89 t dimensions of the machine ca. 8,5x6x8 m No. 1104 The tech. Data are manufacturer or operator information and therefore non- Hodjyqu Rwspfx Ac Tst binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 2004, Technical details: faceplate diameter: 4770 mm swing diameter: 7000 mm turning height: 1000 mm slide stroke: 1000 mm workpiece weight max.: 100000 kg faceplate turning speed range: 2 - 20 U/min feed speeds: 1 - 10000 mm/min rapid traverse: 10 m/min ram head dimension: 250 x 250 mm main drive: 100 kW total power requirement: 200 kW with CNC SIEMENS 840 D 2 Vertical Supports with toolchanger 12 pockets C-axis and driven tooling SK 50 37 Kw 3000 rpm Chip conveyor and coolant attachment Hsdpfx Acjvb Hlwe Tet *

Condition: used, Year of construction: 2002, Technical details: x-travel: 16300 mm y-travel: 2600 mm z-travel: 1600 mm Hedpfsv Uzt Aex Ac Tjt spindle taper ISO: 50 spindle turning speed range: 22 - 4000 U/min rapid traverse: 24 / 36 m/min main drive: 37 kW total power requirement: 50 kW with CNC HEIDENHAIN TNC 430 automatic Universal Milling Head automatic toolchanger 90-pockets coolant attchament and chip conveyor *

Condition: reconditioned (used), functionality: fully functional, travel distance X-axis: 8,300 mm, travel distance Y-axis: 2,000 mm, travel distance Z-axis: 2,500 mm, spindle speed (max.): 3,000 rpm, rotational speed (max.): 3,000 rpm, type of input current: three-phase, coolant supply: 15 bar, spindle motor power: 33,000 W, controller manufacturer: HEIDENHAIN, controller model: 430 CA, power: 0.033 kW (0.04 HP), Equipment: rotational speed infinitely variable, ANAYAK HVM 9000 – CNC moving column milling machine | 8300 mm x travel | Fully overhauled High-capacity CNC bed milling machine with moving column, reconditioned in workshop. Perfect for heavy-duty machining of large components with precision and reliability. 🛠 Key technical specifications: • X-axis travel: 8300 mm • Y-axis travel: 2000 mm • Z-axis travel: 2500 mm • Spindle power: 33 kW – 3000 rpm • Spindle taper: ISO 50 DIN 69871-B • Tool changer: 30 positions • Automatic axes: B and C • CNC Control: HEIDENHAIN TNC 430 CA • Internal coolant: 50 l/min at 15 bar • External coolant: 100 l/min 🔧 Full retrofit includes: • Regrinding and geometry adjustment of Y and column guides • Complete head overhaul: new bearings, seals, gears • Full electrical cabinet update under CE compliance • New telescopic covers, drag chains, and motor wiring • Machine tested and delivered with full documentation ✅ Ideal for: Hedpsqpd D Ijfx Ac Tst • Large-scale component machining • Energy, wind, and railway industries • Mold making, aerospace structures, and shipbuilding 📌 Ready for immediate delivery. Power, scale, and accuracy in one robust CNC machine.

Condition: used, travel distance X-axis: 12,000 mm, travel distance Y-axis: 1,000 mm, travel distance Z-axis: 2,000 mm, position of the milling head: AUTOMATICA, spindle speed (max.): 2,000 rpm, spindle motor power: 29 W, MECOF M 200 MOBILE OVERHEAD MILLING MACHINE Hsdpfxezhnx Is Ac Tet

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, feed length X-axis: 2,500 mm, feed length Y-axis: 1,400 mm, feed length Z-axis: 1,500 mm, spindle speed (max.): 4,000 rpm, table load: 5,000 kg, CNC: SELCA 4045PD AXES TRAVELS X-axis longitudinal travel: mm 2500 Y-axis transverse travel: mm 1400 Z-axis vertical travel: mm 1500 TABLE Table size: mm 1200X1200 Load capacity: kg 5000 Number of divisions: 360.000 T-slots: No. 7 – pitch mm 127 Table axis motor power: kw 6 KOSMO 5 AUTOMATIC BI-ROTARY HEAD Continuous power: kW 28 KOSMO head spindle speed: giri/min 4.000 Plane positioning with HIRTH serration Rear plane rotation: 2,5° Front plane rotation: 3° Tool taper: DIN 69871-A50 Drawbar: DIN 69872-28 (50) PALLET CHANGER: DCN 100 CP MACHINE COMPLETE WITH • Electronic handwheel • Electronic thermal expansion compensation device for the head • High-pressure through-spindle coolnat Hodpfezg Hqysx Ac Tet • Chip conveyor: Double front and rear chip conveyor • Sidesalpa tool machine – 40 positions • Full enclosure • Instruction manuals • CE declaration of conformity

Condition: used, Year of construction: 1950, pressure 500 t distance between columns 1600 mm stroke 60 mm max. ram stroke 60 1 / min ram adjustment 100 mm dayligth 700 mm Table area 1600x1400 mm ram surface 1400x1150 mm weight of the machine ca. 40 t The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. Hodjyutvyjpfx Ac Tot We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 1995, faceplate diameter 4000 mm swing diameter 4300 mm turning height 1750 mm slide adjustment 1000 mm table load 18 t turning speeds 1-92 U/min Control Siemens type 840 D mm Rest 2 ram head dimension 250x250 mm Feed 1-4000 mm/min main gear-box motor 55 kW total power requirement 85 KVA weight of the machine ca. 64 t dimensions of the machine ca. 8x5,8x8 m The machine was overhauled in 2007. The machine is currently designed to machine rings, but can be converted again for machining large parts. Additional information Chip conveyor Hodpfeyquyfex Ac Tst The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: new, Year of construction: 2026, pressing force: 30 t, DURENDUS 30 T Heated Press – Double Column Press – 700 × 500 mm Heated Plates, Sliding Table The machine shown here was already built and delivered to a customer. We can manufacture this machine for you again on very short notice—customized to your individual requirements if desired. This is a hydraulic heated press with electrically heated plates and a manual sliding table for pressing, laminating, and forming processes involving heat. Base price: €42,000 net Hsdpfx Aoy H Dtzoc Tet Options (on request): The listed options are based on completed customer projects and allow targeted customization of the machine to the specific application. The base machine provides a functional standard configuration—in practice, it is often supplemented with additional features and configured according to project requirements. ==== Technical Data + Information: ==== General Information * Design: Double column press * Pressing force: 30 t (adjustable) * Total weight: approx. 3,200 kg * Overall dimensions (W × D × H): 2,000 × 1,500 × 2,850 mm ==== Working Area * Table size: 700 × 500 mm * Heating plates: 700 × 500 × 65 mm * Installation height: max. 800 mm * Table stroke: 500 mm (manual) ==== Table & Ram * Ram stroke: 600 mm * Cylinder diameter: Ø 130 mm * Piston rod: Ø 80 mm * 8-point slide guide for parallelism ==== Speeds * Working speed: 9 mm/s * Return speed: 25 mm/s ==== Hydraulics & Drive * Working pressure: max. 240 bar * Pump output: 12 l/min * Motor power: 3 kW * Hydraulic tank: 80 l * Pressure accuracy: ±5 bar * Hydraulic system with air cooling ==== Control & Operation * SIEMENS S7-1200 control with 7" touch panel * Programmable parameters (stroke, pressure, time, cycles) * Two-hand operation * Electrical connection: 400 V / 50 Hz * Total connected load: approx. 25 kW (including heating) ==== Equipment * Electrically heated press plates up to 200 °C * Temperature monitoring with sensors * Passive pressure holding function up to 60 minutes * Hydraulic and electronic overload protection * Safety limit switches * CE certification * Dual-layer paint finish according to RAL ===== Hot pressing, laminating, plastics processing, rubber and composite material processing, forming press applications Heated press, hydraulic press, double column press, thermo press, laminating press, industrial press Are you looking for a hydraulic press tailored to your application? Contact us for a customized quotation. Our hydraulic presses are manufactured in compliance with German and European Machinery Directives (Directive 2006/42/EC), EC standards, and EU safety regulations. Furthermore, our presses exceed Canadian and European safety requirements as they fully comply with the Brazilian National Safety Directive NR 12, which is based on and extends these standards. Our key strength lies in special purpose machine construction and press automation. We offer custom-built hydraulic presses at surprisingly affordable prices. For the hydraulics, we primarily use components from leading European manufacturers.

Condition: used, machine/vehicle number: 4396, pressing force: 200 t, pressure:200 t distance between columns:1200x1000 mm stroke:600 mm total power requirement:32,5 kW weight of the machine ca.:20,5 t draw back pressure:20 t :1 Stück voltage:400 V frequency:50 Hz :24 V :Rexroth/Bosch dayligth:800 mm working area:1200x1000 mm :1200x1000 mm work height max.:1100 mm :170 mm/sek. :150 mm/sek. :15 mm/sek. quantity of oil:500 l :220 V memory:200 Programme :20-200 über Monitor t :5-170 mm/sec. :0-10 sec Hjdpfxefxyh Aj Ac Tet :2-10 mm/sec :750x950 mm :300 mm :5-50 t :2-80 mm/sec :1000 kg

Condition: used, Year of construction: 1994, x-travel 12000 mm y-travel 2500 mm z-travel 1000 mm Hjdpfeyqtq Aex Ac Tet control Heidenhain TNC 415 taper ISO 50 P.D.B. spindle speeds 20 - 1800 mm voltage 380 V total power requirement 37 kW A.T.C. 60 pos. Indexing universal head The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team