Used Cardboard Press for sale (12,803)

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Nkjdpfx Asw A Amrjgneu Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Njdpfeu Rwa Isx Agnjku Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Die depth: approx. 8 mm Njdpfxowbvmis Agnsku Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Nksdpoi A A Tbofx Agneu Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Nedpfetx E Rqsx Agnsku Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, Pneumatic press, compressed air press BOSCH type Manufacturer no.: Year of manufacture: 1980 Nedpfxoh U Dtus Agnjku Pressing force: 18 kN = 1.8 t at 5 bar 15 kN = 1.5 t at 4 bar 12 kN = 1.2 t at 3 bar 8 kN = 0.8 t at 2 bar 6 kN = 0.6 t at 1.8 bar Throat depth: 100 mm Ram stroke: 70 mm Table size: 245 x 200 mm Ram face: Ø 45 mm Max. installation height: 235 mm Clamping pin bore: Ø 20 mm with clamping screw Compressed air requirement: 5 bar - Pressing force infinitely adjustable via pressure regulator - Pneumatic cylinder with ram adjustable in height by 90 mm - Pneumatic dual-hand control - Mounted on a metal frame with wooden boards Required floor space (L x W x H): 1050 x 700 x 1600 mm Weight of pneumatic press: 82 kg Weight including table frame: 140 kg In very good condition

Condition: used, Single column hydraulic press DUNKES type HZT 2,5 Machine No. H94-2558 Year of construction 1994 pressure force 2,5 ton. throat 180 mm table area 420 x 300 mm drop-through opening in table 60 x 185 mm ram surface Ø 40 mm clamping spigot bore Ø 20 mm Nodpfx Agjh Uhqysnsku ram stroke 160 mm Installation height max. 250 mm Rapid traverse downward 65 mm/sec. Rapid traverse upwards 160 mm/sec. Working speed 8,3 mm/sec. Table height above floor 950 mm Hydraulic operating pressure 135 bar Tank capacity hydraulics approx. 100 liters Drive power 1,5 kW Mains connection 400 Volt, 50 Hz - Installation height can be increased by shortening the piston rod by 80 mm - Pressure and travel cut-off - 2-hand operation at the machine - stroke counter - safe press control with 2 monitored hydraulic valves - UVV 11.064 VGB 7.n.5.2 (for manual insertion work) - 32047 read off operating hours - Electrical circuit diagram and hydraulic diagram available space requirement L x W x H 1100 x 980 x 1950 mm weight 700 kg very good condition

Condition: used, Single column eccentric press MÜLLER GEFREES type PDET 5 S/EK Machine No. Year of construction 1988 pressure force 5 ton. throat 125 mm Nkedpfx Agsik Srwenou head clearance 170 mm table area 280 x 220 mm waste hole Ø 90mm ram surface 160 x 100 mm stroke adjustment 4 to 40 mm ram adjustment 30 mm Installation height largest stroke top max. 210 mm Stroke rate 200 strokes/min. Clamping spigot bore Ø 25 mm Table height above floor 900 mm motor power 0,55 kW mains connection 380 volt, 50 Hz - pneumatic clutch-brake combination - electric foot switch - switch cabinet at the machine space requirement L x W x H 900 x 600 x 1700 mm weight 530 kg very good condition

Condition: used, Single-column hydraulic press HYDRAP type HPSK 25 No. 6312 Year of construction 1989 Pressure force 25 ton. Ram stroke 500 mm throat depth 300 mm Installation height 700 mm Table surface 1000 x 500 mm Table bore Ø 210 mm Plunger surface 400 x 360 mm Clamping pin bore Ø 40 mm Table height above floor 855 mm Feed speed in rapid traverse 280 mm/sec. Pressing speed 3.5 mm/sec. to 25 mm/sec. Return speed 280 mm/sec. Hydraulic tank capacity 240 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz. - Operation and programming via SIEMENS S5 with OP1 control system - Measuring system for stroke adjustment - Pressing speed infinitely variable via potentiometer - Pressure setting infinitely adjustable manually via pressure regulator - Short stroke device - Mechanical tool clamping on ram with T-slots and clamping pin hole - Switch cabinet with electrical control on the machine - Two-hand operation and electrical connection for foot control - Control provided for electrical mold monitoring - Hydraulic diagram and electrical diagram available Nedpehrakvefx Agnjku Space requirement L x W x H 1800 x 1200 x 2930 mm Weight approx. 4 tons good condition

Condition: used, Single-column toggle press MAY - MAYPRES - KOMATSU Type MKN 1-63/6 Eccentric toggle press, eccentric press Year of manufacture approx. 1984 Pressing force 60 tons Thrust 160 mm Table size 580 x 360 mm Njdov Uraajpfx Agneku Ram surface Ø 270 mm Clamping pin bore Ø 40 mm Distance between columns 218 mm Ram stroke 60 mm Ejector stroke 15 mm Ram adjustment travel 30 mm Max. installation height 300 mm (with intermediate table plate) Stroke rate 70 strokes per minute Motor speed 1400 rpm Motor power 3 kW Power supply 380 V, 50 Hz - Pneumatic clutch and mechanical brake with pneumatic release (separate clutch-brake combination) - Table intermediate plate L x W x H 580 x 360 x 58 mm, with holes and cutouts - Mechanical ejector, ejector device in the machine table, Ø 80 mm - Electric two-hand control and foot switch - Movable safety screen, UNIDOR protective housing with pneumatic front screen - BALLUFF cam switch Space requirement L x W x H 1400 x 1200 x 1850 mm Weight 3 tons Good condition

Condition: used, Single column eccentric press PELS - RICHTER type PEKR 125 Machine. No. 20684 Year of construction 1967 pressure force 125 ton. throat 430 mm table size 1100 x 750 mm ram area 890 x 650 mm table opening Ø 400 mm stroke adjustment 6 to 115 mm ram adjustment 100 mm installation height largest stroke top max. 450 mm Clamping spigot bore Ø 50 mm Stroke rate 60 strokes/min. Table height above floor 900 mm motor power 7,5 kW Mains connection 380 Volt, 50 Hz - Overload protection by crushing plate in ram - Compressed air clutch-brake combination DESCH - ram weight balancing cylinder - manual ram adjustment - two-hand operation - cam gear Nkodpfx Agjfim Thjnju - Grease central lubrication Vögele - stroke counter Space requirement L x W x H 2300 x 1450 x 3030 mm weight approx. 10 ton. good condition

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition Njdpfx Aslb I Dzsgneku

Condition: used, Single column eccentric press WEINGARTEN type ERV 40 Machine No. 537 / 65 Year of construction 1965 Compressive force 40 ton. throat 230 mm table size 570 x 470 mm ram surface 250 x 200 mm Nkodpoffm Hhefx Agnou clamping spigot bore Ø 40 mm installation height max. approx. 520 mm stroke adjustment 8 - 88 mm slide adjustment travel 63 mm Stroke rate 70 strokes per minute Drive power 3 kW Mains connection 380 Volt, 50 Hz - Table height adjustment - Overload protection by crushing plate - clutch-brake combination by WEINGARTEN friction thread clutch - electric 2-hand operation and foot switch - central lubrication via hand pump space requirement L x W x H 1600 x 1150 x 2300 mm weight approx. 2,6 ton.

Condition: used, Clinching unit TOX - Pneumatic-Hydro Toxpress Hydro-pneumatic press TOX Pressotechnik KRAFT PAKET Type CRS 03.62 No.: 207599.2 Year of construction approx. 2005 Pressure capacity: max. 80 kN = 8 tons Projection: 20 mm Installation height: 32 mm - Built-in clinching tool - Pneumatic valve for control Nodpfjdz Sqqox Agnoku - Push-through joining or clinching - For creating a form-fit connection between 2 sheets without piercing or heating the sheets - Mounted on the stand - with simple electrical control and foot switch Own weight: 230 kg Comes from a production plant, sold without electrical control

Condition: used, Single-column hydraulic press SCHÖN type FES / C 7 Machine no. No. 4281 Year of construction 1995 Pressure force 7 ton. throat 170 mm Projection round cycle station 60 mm Table size 310 x 200 mm Rotary indexing table Ø 400 mm, with 12 indexing stations Plunger surface approx. Ø 100 mm Plunger plate 315 x 200 x 35 mm Ram stroke 100 mm Installation height rotary table - ram plate max. 130 mm Table height above floor 890 mm Ram speed rapid traverse downwards approx. 300 mm/sec. Ram speed rapid traverse upwards approx. 300 mm/sec. Ram speed Working speed approx. 30 mm/sec. Nsdpfsr I E Itox Agneku Drive power 1.5 kW Mains connection 380 Volt, 50 Hz Tank capacity approx. 50 liters hydraulic oil - Rotary indexing control via SIEMENS S7- 1200 - GECHTER pneumatic rotary indexing table with 12 indexing stations - Mechanically adjustable fixed stop - Adjustable pressure holding time in the UT - electrical 2- manual operation Space requirement L x W x H 1450 x 850 x 1900 mm weight 700 kg good condition

Condition: used, Single-column hydraulic press MAE type S63SZ SO . 551277 Year of manufacture approx. 1977 Nominal pressing force: 63 tons Pressing force: 50 tons (practically tested) Throat depth: 320 mm Table area: 850 x 630 mm Ram area: 1050 x 500 mm Ram stroke: 500 mm Max. installation height: approx. 730 mm Nodpsdzp Trjfx Agneku Table height above floor: 970 mm Hydraulic tank capacity: 600 liters Drive power: 15 kW Power supply: 380 Volt, 50 Hz - Hydraulic draw cushion below the table with bores through the tabletop - Two-hand operation - Electrical control cabinet damaged Required space (L x W x H): 2000 x 1200 x 3420 mm Weight approx. 5 tons The machine is operational, the control cabinet is mechanically damaged. During test run, the machine achieves a pressing force of 50 tons, presumably a pressure relief valve is venting.

Condition: used, Double column hydraulic press SMG type HBP 200 - 2000 / 2000 make no. 7.4117 year of construction 1986 - rebuild 2000 pressure force 200 ton. Stand passage front 2050 mm column passage sideways 2030 mm table area 2800 x 2000 mm ram area 2000 x 2000 mm ram stroke 700 mm installation height max. 1850 mm Table height above floor 750 mm ram retraction force 33 ton. Rapid feed speed 500 mm/s Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety distance 230 mm Motor power main motor 75 kW Motor power control pump 11 kW Mains connection 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots at the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking at TDC Nodpfx Asdzp Tcsgnsku - Measuring system with glass scale - Electrical control renewed in 2000 with SIEMENS SPS S7 - adjacent switch cabinet - 2-hand control panel adjacent - ground level installation - central lubrication - Operating instructions with circuit diagrams Space requirement of the press standing L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space requirement for horizontal transport L x W x H 5900 x 3250 x 2950 mm weight 38 ton. The machine was used as a production press at Volkswagen until 2000. From 2000 the machine was used as a tool testing press in a tool shop. good condition

Condition: used, Year of construction: 1997, Press capacity: 315 ton Ram stroke adjustable: 30 - 100 mm Slide adjustment: 100 mm Shut height (stroke down, adjustment up): 370 mm Table surface area : 1600 x 1100 mm Slide area: 1600 x 1100 mm Hole in table: 600 x 180 mm Number of strokes: 15 - 180 s.p.m. Table height over floor: 1200 mm Required power: 170 kW Height over floor approx.: 4900 mm Dimensions L x W x H: 4900 x 1900 x 4900 mm Weight of machine approx.: 55 ton Standard configuration The press was converted to CE standard in press was 2021 converted to a SIEMENS S7 control conveyor system still has a SIEMENS S5 control system. Extended machine accessories Die lifters in the table Automation Feeding unit KEMMERICH consisting ofDecoiler levelling machine roll feeder Nksdpfjuqd Tmjx Agneu Coil loading car

Condition: used, Year of construction: 1981, Technical details: Nkodoyk Utljpfx Agnju pressure: 40 t

Condition: ready for operation (used), controller manufacturer: TS Touch, installation height: 515 mm, operating speed: 20 mm/s, reverse speed: 90 mm/s, total length: 2,900 mm, total width: 1,850 mm, total height: 2,260 mm, power: 9 kW (12.24 HP), travel distance Z-axis: 275 mm, empty load weight: 5,100 kg, passage width: 2,050 mm, 4 assen: Y1 / Y2 Y3 / X Nsdpfx Aoyf Ruhegneku touchscreenbediening Willa/Modufix bovengereedschap Y3 = onderste tafel, in hoogte verstelbaar De onderste tafel fungeert tevens als dichtdrukmatrijs (pneumatisch). Er is ook (elektrische) doorbuigingscompensatie in de onderste tabel. Capacity: 40 ton x 2050 mm Backgauge: CNC Max distance between table -- ram: 415 > 575 mm (variable) Locking speed: 90 mm/sec

Condition: ready for operation (used), controller manufacturer: Cadman Touch-B, throat depth: 350 mm, installation height: 500 mm, operating speed: 10 mm/s, reverse speed: 80 mm/s, total length: 5,545 mm, total width: 1,990 mm, total height: 3,380 mm, power: 30 kW (40.79 HP), travel distance Z-axis: 250 mm, empty load weight: 23,000 kg, passage width: 3,150 mm, table width: 250 mm, 5 assen: Y1 / Y2 / X / R / V Laserbeveiliging voor en achter CNC-bombering boven- en onderaan LVD-tooling opname Capacity: 250 ton x 4100 mm Nsdpfxeyf Rt Ro Agnoku Backgauge: CNC Locking speed: 80 mm/sec

Condition: excellent (used), functionality: fully functional, Year of construction: 2005, operating hours: 12,096 h, Amada hydraulic press brake type HFT 130-3 working width 3100 mm max. pressing force 130 tons CNC-controlled Y1 Y2 X and R axes CNC control CNC OP 2000 Fiessler light curtain Drive power 12.5 kW Weight 8200 kg Nksdpfx Aoxhfuyegnsu

Condition: ready for operation (used), functionality: fully functional, FOR SALE: BRUDERER BSTA 60 High-Speed Stamping Press With Automatic Strip Feeder BBV 300/200 600 kN | 100–800 spm | Fully automatic | Top-tier Swiss quality Technical Highlights: Nominal force: 600 kN Stroke rate: 100–800 strokes per minute Max. feed length: 200 mm. Year: Unknown (No ID Plate) / Tested under power: 2025 Drive power: 30 Hp Control voltage: 24V AC Power connection: 440VAC / 50Hz Adjustable stroke: 20 / 25 / 31 / 38 / 45 /51 / 58 / 64 / 70 / 76 mm Shut/Ram height adjustment: 80 mm Working Dimensions: Max tool installation width: 620 mm Strip pass width: up to 320 mm Ram area: 800 × 500 mm Table area: 620 × 680 mm Max strip width: 300 mm Max feeding pitch: 200 mm Max material thickness: 6 mm Feeding angle: 180 Deg Machine Dimensions: Machine footprint (L × W × H): 2210 × 2075 × 2190 mm Weight (approx.): 8,000 kg Equipment Includes: Nodpexz Ugxefx Agneku Feeder BBV 300 – fully synchronized mechanical strip feeder system Integrated control cabinet Pneumatic clutch and brake Adjustable stroke and shut height Compressed air connection: 6–10 bar Oil cooling unit included Ready for integration with peripheral systems Machine in excellent technical and visual condition Fully tested Immediate availability from Europe Worldwide shipping available Contact us today for pricing and further technical details. Let us help you upgrade your production line with Swiss precision engineering.

Condition: used, functionality: fully functional, Very nice one-color offset press for sale. Brand: Sakurai, model 52 E, year 1996. Of course, you are welcome to test this machine with us. We can arrange transport/packaging for you and load it into a truck or container. Please inquire for a price including transport (location: the Netherlands). Regards, Henk Hoos. Nksdpfx Aoyk Hqpegnou

Condition: good (used), Year of construction: 1969, For sale is a veneer press from Ott. The machine is in perfect working condition and can be inspected on site. Nkjdpfx Agoymmgisnsu Sale is on behalf of a customer. Machine location: Friedeburg area. Machine details: Pressing area: 225 cm x 120 cm Year of manufacture: 1969 Motor power: 12 kW Includes heating Emergency stop cable The machine has been repainted at some point