Used Brush Sanding Machine for sale (64,671)

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Hsdot Tqy Ejpfx Ac Tet Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: good (used), Year of construction: 1997, functionality: fully functional, working width: 1,300 mm, passage height: 300 mm, power: 63 kW (85.66 HP), input voltage: 400 V, input frequency: 50 Hz, the machine is in good working order and ready for use. Hodpoy Tmqcjfx Ac Tet

Condition: used, Year of construction: 2022, Belt width: 150 mm Belt length: 3000 mm Table size: 960 mm x 350 mm Auxiliary table: 330 mm x 330 mm Veneer sanding device: yes Oscillation: yes Tilting sanding unit: yes Extraction port: 120 mm Motor power: 3 kW Machine length: 1910 mm Hjdpfx Acszq Dczs Tot Machine width: 840 mm Weight: 330 kg

Year of construction: 2008, condition: good (used), functionality: fully functional, machine/vehicle number: 10999, DESCRIPTION Double-sided grinding machine / grinding machine top/bottom Manufacturer Löwer Type DSM 3000 with workpiece return Bthgq0Ygu0 Working width: 290 mm Grinding thickness: 2-200 mm Shortest workpiece length: approx. 320 mm Equipped with: 1x grinding unit from above, 7.5 kW 1x brushing unit from above, 0.37 kW 1x grinding unit from below, 7.5 kW 1x brushing unit from below, 0.37 kW Grinding belt dimensions: 300 x 1800 mm Hjdpfx Aov Dfp Hec Tst Electric height adjustment, 0.37 kW Adjustable feed, 6/11/16 m/min. Compressed air: 6-8 bar Dimensions approx. 2700 x 1100 x 1900 mm Weight approx. 1600 kg

Year of construction: 2005, condition: good (used), machine/vehicle number: C9 15840, Profile brushing machine Tagliabue LB 2 Model: LB 2 Hodpfx Aog Rn Iaec Tot TECHNICAL DATA: Year of manufacture: 2005 Tagliabue edge sander with 4 oscillanting sanding units. Two vertical rollers and 2 inner transversal rollers, for transversal brushing.

Condition: excellent (used), working width 620 mm two brush rollers adjustable roller height 400 V power supply safety switch Hsdpezwdvhefx Ac Tjt year of manufacture: 2006

Condition: used, Technical details: grinding spindle speed: 1440 U/min voltage: 220 V / Hz total power requirement: 1,1 kW machine weight approx.: 75 kg space requirements of the machine approx.: L:0,4 x B:0,7 x H:1,15 m Polishing block stands on welded sectional steel base with foot plate (400x400x5mm) -wire brushes Ø 200x25mm each are mounted on the left and right -without sanding support -Protection class IP44 -Operation via ON/OFF switch * Hsdpfx Aceu Ng S Do Tst

Condition: used, Year of construction: 2017, functionality: fully functional, We are offering this used HEESEMANN UKP 20 edge sanding machine, year of manufacture 2017. Manufacturer: HEESEMANN Model: UKP 20 Year: 2017 Condition: used If you have any further questions or require more information, please do not hesitate to send us a message or give us a call. If needed, the order confirmation with all technical details can be sent. 1 workpiece transport system – total length 5,015 mm – driven by a 1.5 kW three-phase motor, with double chain for workpiece transport Feed speed adjustable from 5 to 25 m/min, frequency-controlled, working height constant at 880 mm, including integrated control cabinets; Including adjustable stop ruler with digital readout and including counter fence with central width adjustment with central height-adjustable and laterally adjustable top pressure bar with digital display, which presses plate-shaped workpieces with ball-bearing rubber rollers (roller pitch 38 mm), including support rollers to extend the support for large workpieces, extendable sideways by approx. 1,500 mm. 4 side guide rollers between the sanding units for secure transport of strips 1 Industrial PC 3.0/4" LCD-TFT color display, 800 x 600 pixel resolution CF card 1GB Operating system: Windows Embedded Standard Touch-screen version with display for production and downtime periods. Ethernet connection available. 2 belt sanding units "M 4" – positions 1 and 2 for sanding straight edges, with intermittent belt blow-off device, belt break detector, tool holder with quick-change device, base plate for sanding tool, prepared for electronic path control for automatic engagement and disengagement of the sanding tool, operating in both climb and counter rotation. Belt dimensions: 2,300 x 80 mm Belt speed: 0/7–12 m/s Motor rating: 3.0 kW with electronic frequency control for stepless adjustment of the belt speed. Electronic sanding pressure control from the terminal. 2 oscillation devices (positions 1 + 2) For optimal belt utilization 2 belt sanding units "K 4" – positions 3 and 4 incl. stand, for sanding small profile sections, also suitable for edge rounding; can be swiveled 90° upwards and 45° downwards, belt break detector, tool holder with quick-change device, base plate for sanding tool, intermittent belt blow-off device, prepared for electronic path control for automatic engagement and disengagement of the pressure tool, including climb and counter rotation, designed for manual adjustment and digital indicators for the adjustment axes. Hodpoy A D Ecofx Ac Tst Belt dimensions: 2,000 x 50 mm Belt speed: 0.5–8 m/s Motor rating: 1.1 kW with electronic frequency control for stepless adjustment of the belt speed. Electronic sanding pressure control from the terminal. 4 electronic path controls for fully automatic, timed engagement and disengagement of the sanding tool depending on the set feed speed, sanding pressure, and angle position of the units. 2 steel tools for straight edges, equipped for air cushion sanding, incl. base plate, for 1 "M4" unit, item no. 9000191310 2 steel profile tools equipped for air cushion sanding, incl. base plate, for 1 "K4" unit, item no. 20000025684

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: VO995, total length: 1,700 mm, total width: 1,000 mm, total height: 1,150 mm, table length: 880 mm, table width: 370 mm, overall weight: 260 kg, power: 2.2 kW (2.99 HP), grinding width: 150 mm, grinding length: 2,580 mm, Machine type: LVO 120, Machine number: VO995, Year of manufacture: 2009, Main motor: 2.2 kW, Oscillating motor: 0.11 kW Hodpfx Acey Nznue Tst

Condition: used, Year of construction: 2017, - 4 belt grinding units - Frequency control for all units - Electronic grinding pressure control Universal edge and profile grinding machine Manufacturer: Heesemann Type: UKP 20 Year of manufacture: 2017 Technical data Workpiece transport system - Total length: 5015 mm - Driven by a 1.5 kW three-phase motor with a double chain for workpiece transport - Feed rate in the range of 5-25 m/min, frequency-controlled - Working height constant at 880 mm - incl. integrated control cabinets - incl. adjustable guide rail with digital display and incl. counter rail with central width adjustment 4 lateral guide rollers between the grinding units for secure transport of workpieces Industrial PC 10.4" - LCD-TFT color display - Touch screen version - with display for production and downtime - with program memory for 100 programs 2 belt grinding units "M 4" Pos. 1 and 2 - for grinding straight edges - Belt dimensions: 2300x80 mm - Belt speed: 0.7-12 m/s - Motor power: 3.0 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 2 oscillation units for "M4" (Pos. 1+2) For complete utilization of the grinding belt 2 belt grinding units "K 4" Pos. 3 and 4 - for grinding small profile sections - can also be used for edge breaking - Can be swiveled 90 degrees upwards and 45 degrees downwards - Belt tear switch - Tool holder with quick-change device - Intermittent belt extraction device - Belt dimension: 2000x50 mm - Belt speed: 0.5-8 m/s - Motor power: 1.1 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 4 electronic control units - for the fully automatic timing of the lowering and raising of the grinding tool, depending on the set feed rate, the grinding pressure and the unit angle setting Note: Hjdpfx Aezuzb Ajc Tst The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: good (used), Year of construction: 2000, functionality: fully functional, working width: 1,300 mm, passage height: 200 mm, power: 63 kW (85.66 HP), input voltage: 400 V, input frequency: 50 Hz, the machine is in good condition. Hsdpfoy Tm Alox Ac Tjt

Condition: good (used), functionality: fully functional, 1st station: deburring of sheet metal edges, 2nd station: deburring of notches and outer radii, with VA brushes; maximum sheet thickness: 5 mm Hsdpfxjzwt Rbe Ac Tot

Condition: used, used, top condition Machine cleaned and lubricated Partially overhauled. Hjdpjy H N Tmofx Ac Tet Emergency stop button renewed. All sliding pads replaced Motor cover repaired. Oscillation overhauled and adjusted. Test run conducted Manufacturer: SCM Samco Model: Unilev 15 Machine No.: 98510909050 Motor: 2.2 / 3 kW Oscillation: pneumatic, infinitely variable Veneer edge sanding unit Front table approx. 1400 x 220 mm Rear table approx. 1440 x 220 mm Tilting table double-sided Belt tension pneumatic Belt length 2170 mm Belt width 150 mm 2 belt speeds: 10 / 20 m/sec mobile Round edge sanding device with support table approx. 500 x 400 mm Extraction connection D 120 mm Required space approx. 1500 x 750 x 1400 mm Weight approx. 490 kg Storage location: 97447 Gerolzhofen, free loaded, unpacked Delivery in as-inspected condition, without warranty or guarantee

Condition: good (used), Code: 0351 Brand: VOLPATO Model: LS - 1N - CE Standard Automatic edge sanding machine for edges and profiles in wood, solid wood, veneer, painted and various materials - CE Standard Technical data Max working height mm 110 Min working length mm 100 Variable-speed belt feed 5–30 m/min – Motor Kw 1,5 Tilting oscillating sanding unit – 2-speed motor 700–1400 rpm – Power 2 Hp Pneumatic belt tensioner – Timed entry and exit of the pad Mechanical oscillation of abrasive belt 0/20 mm Lifting and tilting via handwheel with special key Removable support for large panels Abrasive belt dimensions 80 x 2450 mm Suction inlet diameter 100 mm Compressed air 5–6 atm Hsdsy A Sq Tepfx Ac Tet Overall dimensions mm 2600 x 1400 x 1500 h Weight kg 720

Condition: new, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm LÖWER-DoubleSander Solid DSM 2004 ----- Double-sided four-belt single wood sander for Sanding solid wood such as window frames etc. Highly stable top design with innovative details. Suitable for high continuous loads even with higher chip removals. - sanding units arranged one after the other for pre-grinding, Fine sanding and finishing sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberized roller and shoe 3. Finishing unit with fiber brush - Directly driven grinding rollers for slip-free Power transmission - maintenance and wear-free CERMET-coated grinding wheels shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and longer sanding belt service life - force-guided pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the Grinding rollers - Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large Grinding dust extraction - motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball screws bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom via precision Threaded spindle with dimension display via scale ring (Resolution 0.1mm) - Sanding belt tension via pneumatic cylinder constant clamping pressure - Sanding belt change with pneumatic belt relaxation Within seconds - Adjustment option for the sanding belt run Band change - electro-pneumatic compressed air monitoring - Anti-running protection via contact roller if it is too thick workpieces - Workpiece transport via calibrated non-slip and non-stick fixed conveyor belts over heavy, cast tables Finely planed surface and spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and consistent Workpiece transport - Feed gear motor with stepless speed 4-20 m/min - all motors electrically protected - ergonomically arranged controls - digital thickness display (resolution 0.1mm) with modern Magnetic tape system Technical data: - Sanding belt speed 22 m/s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Grinding thickness 2-180mm - four brake motors for 5.5 kW drive - Feed motor 1.5 kW - Feed speed 4-20 m/min. - automatic height adjustment 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle 2 x 180mm 2 x 120mm Hodpjvnv Tqefx Ac Tet - Extraction air speed 20 m/s - Pneumatic connection 6 bar - Working height 870mm - Length (with soft disc 2740mm) 2600mm - Length with control panel (with soft disc 3035mm) 2985mm - Width 880mm - Height 1910mm - Weight approx. 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version ----- Price of the above machine on request! ----- Special accessories with additional charge: Workpiece blow-off - using nozzles from above and below at the machine outlet arranged, pneumatically controlled 4-belt sanding belt blowout via nozzles directly on the radii of the tension rollers inside the suction arranged, timer controlled on/off 5 seconds each, can be switched on separately Di...

Condition: ready for operation (used), maximum belt width 240mm mechanical oscillation Hodpozhuv Hjfx Ac Tot unit spacing 200-1290mm screw-type belt tensioning star/delta starter manual adjustment of unit spacing cast iron housing dimensions of the side table 920x350mm two 7.5kW motors

Condition: excellent (used), 4 kW motor Roller feed system Sanding belt length: 100 cm Hsdszu Ng Tjpfx Ac Tst Working height: 14 cm Table with adjustable angle and height

Condition: used, total length: 4,750 mm, total width: 2,640 mm, total height: 2,030 mm, Colour: White Empty weight: 3.500 kg The Bauerrichter ESR-1 is a polisher designed for creating high-gloss surfaces on various materials. Below is a summary of its technical specifications: Technical Specifications: CharacteristicSpecificationElectric connection380 V, 20 kDimensions (L x W x H)5,600 mm x 2,400 mm x 2,100 mmWeightAbout 3,000 kgWork table dimensions1,350 mm x 3,200 mmMaximum workpiece height< 100 mmDiameter polishing rollerØ 400 mmFeed rateFrequency controlled Characteristics: Polishing unit:Moves over a fixed work table and is equipped with an inclined, oscillating polishing roller. The height and oscillation speed are infinitely adjustable. Polishing roller: Equipped with special 400 mm diameter polishing rings that ensure longer life and lower operating costs. Quick-change system: Allows easy and quick replacement of polishing rings, reducing set-up time. Workpiece attachment: Standard equipped with a quick clamping system; optional vacuum clamping system is available for faster and more comfortable operation. Construction: Robust welded precision work table with phenolic resin bonded film plates, resistant to heat, moisture and chemicals. Drive: High quality SEW electric motors with energy efficiency class EFF1 (IE2), known for their robustness and durability. This machine offers an efficient solution for polishing various materials and is designed with durability and ease of use in mind. - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: 150610 - Number of units [pcs]: 2 - └ Unit 1: - - Position: Top - - Type of unit: Brush unit - - Number of brushes [pcs]: 1 - - Brush length [mm]: 1500 - - Brush diameter [mm]: 180 - - Motor power [kW]: 11 - └ Unit 2: - - Position: Top - - Type of unit: Brush unit - - Number of brushes [pcs]: 7 - - Brush length [mm]: 75 - - Brush diameter [mm]: 180 - Max. working width [mm]: 1440 - Max. passage height [mm]: 250 - Infeed table length [mm]: 5150 - Outfeed table length [mm]: 5150 - Voltage [V]: 400 - Transport dimensions: 4750mm x 2640mm x 2030mm (l x w x h) - Transport weight [kg]: 3500kg - Transport packages [pcs.]: 1 Hedpfx Aewnhxdec Tjt Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Second-hand machine Year of manufacture: 1988 Condition: well-maintained Features and technical specifications: - Length of work tables: 1440 mm - Total width of the two work tables: 710 mm - Tilt adjustment of the work tables: 0 – 30 degrees Hodpfx Acozk Ny Eo Tot - Working pressure: 6 bar - Sanding belt length: 2170 mm - Sanding belt width: 150 mm - Sanding belt speed: 10–20 m/sec - Vertical adjustment of the oscillating unit: 125 mm - Air consumption: 25 NL/min - Electrical specifications: 400 V / 2.9 kW Weight: 490 kg Availability: at short notice Storage location: 63934 Röllbach

Condition: excellent (used), Catalog number: 8075 TECHNICAL DATA - Table length: 2200mm - Table width: 700mm - Main motor: 2.2kW - Manual beam lifting - Abrasive belt width: 160mm - Grinding head - Dust extraction nozzle diameter: 120mm - Overall dimensions (L/W/H): 3060x1240x1430mm - Weight: 250kg ADVANTAGES Hodjzuk Hujpfx Ac Tot – Made in Austria – Unpainted – Used sander, very good condition Net price: 6500 PLN Net price: 1548 EUR, depending on the exchange rate of 4.20 EUR (Prices may vary due to exchange rate fluctuations)

Condition: good (used), Year of construction: 2001, Quickwood Rustication / Brushing Line on 03 sides with 02 brushes per side Hodsvy Eu Iepfx Ac Tjt

Year of construction: 2003, condition: good (used), functionality: fully functional, machine/vehicle number: 03234, 6 Brush ( 3 pairs) descaling machine for steel wire size 5.5mm - 16.0 mm max (low carbon) Hsdpfox R Uzdox Ac Tjt Brush pairs arranged in a 60 degree offset for maximum effect. A very clean looking machine. On site viewing and inspection recommended

Condition: used, Aging machine, brushing machine QuickWood 1/26 Hsdpfxezkh E Te Ac Tjt

Condition: used, Brush deburring machine, tube deburring machine RSA type STL 1 Year of manufacture: approx. 1990 Brush diameter: 250 mm Brush width: 25 - 60 mm Speed: 1430 / 2870 rpm Power: 2 / 3 kW Mains connection: 380 Volt, 50 Hz Hsdpfxexpqy Rj Ac Tst - Material support - Extraction connection Ø 75 mm Space requirement L x W x H: 650 x 550 x 440 mm Weight: 100 kg Good condition

Condition: excellent (used), Year of construction: 1986, functionality: fully functional, The machine is in good condition, has been in use until recently, and is now available for sale due to a new purchase. The machine has been regularly serviced. It is ideally suited for sanding solid wood, both straight and profiled parts. Hjdpfx Aezdvupsc Tot The processing side, with its guides, features an adjustable sanding shoe. The feed mechanism is an ideal addition for finer edge sanding on straight edges. The machine has a compressed-air-operated belt oscillation for optimal sanding results. The machine has a chassis. Various sanding belts are included.