Used Bollegraaf for sale (20)

Condition: like new (used), Year of construction: 2022, operating hours: 6,000 h, machine/vehicle number: 006424, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 75 kW (101.97 HP), Equipment: documentation/manual, This very young baler is sold by Bollegraaf Recycling Solutions. This is a HBC100 (75kW) baler featuring cross wires, FULL HARDOX, and a Bollegraaf chain conveyor with Bordoflex. Both the chain conveyor and the baler are equipped with all possible options for maximum efficiency in baling all types of plastics. Both units were built in 2022 and have very few operating hours. The previous owner purchased a new Bollegraaf system and traded in the machines in question. After disassembly, this baler is sold with a 3-month warranty. HBC100K Baler (75kW) Podpfx Aexvh Ewog Dogw 390mm supports Intermediate hopper Conveyor chute Platform with caged ladder Additional photocells Frequency controller for the main motor for energy savings APCP (adaptive self-learning channel pressure control for consistently optimal bale weights) Cross wires (3 horizontal wires and 5 vertical wires) Full Hardox lining inside the baler Bale exit Hydraulic lifting mechanism for both knotting sections for improved accessibility/maintenance Bale length display Air conditioning on the control panel Chain conveyor frequency controller Hydraulic oil heater Hydraulic unit cooler 4G modem for remote support Chain conveyor Bollegraaf HBT 1200/1800*20400 Equipped with Bordoflex for extra chain protection Dirt discharge plate Supports Chain lubrication

Condition: excellent (used), Year of construction: 2021, functionality: fully functional, Bollegraaf HBC 120 baler with pre-compressor and air separator, year of manufacture 2021, in very good condition Technical specifications: Manufacturer: Bollegraaf Model: HBC 120 Year of manufacture: 2021 Operating hours: 5,800 (as of October 2025) Pressing force: 120 t Drive power: 90 kW Total power: 141 kW Capacity at 30 kg/m³: 16.2 t/h 50 kg/m³: 25 t/h 100 kg/m³: 47 t/h Bale size: 1,100 x 720 mm (W x H), variable length Pgedpfxoxwazyo Ag Dew Bale weight: 550–880 kg Tying: 5-fold vertical Dimensions: approx. 11,750 x 2,500 x 4,590 mm (L x W x H) Weight: approx. 31,600 kg Scope of delivery includes the baler with pre-compressor, perforator, binding platform, large digit display, remote control, wire stand, and preparation for a personnel safety system. Materials: paper, cardboard, film, PET, beverage cans, textiles. The baler is in very good condition. It will remain in operation for approximately another 4 months and can be inspected under operating conditions upon request. Please note: All technical specifications are based on the manufacturer's information. We do not accept any liability for the information provided or for potential errors. All offers are subject to change, prior sale and withdrawal at any time. Viewings can be arranged by appointment. Sale is ex location, without warranty or guarantee.

Condition: excellent (used), Year of construction: 2017, operating hours: 19,187 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, overall weight: 52,000 kg, Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 140 Year of construction 2017 Working hours 19,187 hours, stand October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm Capacity per cycle time 4,34 m³ Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm Driving motor 2 x 75 kW Connected load 226 kW Full load current 428 A Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 800 up to 1300 kg, depends on material and bale lenght SPS controller (manuf., type) Telemecanique TSX Micro Operating panel (manuf., type) Schneider MAGELIS Touch Baler dimensions built up with hopper 13,200 x 27,000 x 7,344 mm (l x w x h) Transport dimensions only baler 13.200 x 2.750 x 3.450 mm (l x w x h) Machine weight baler approx. 52 tons Technical data chain belt conveyor: Manufacturer Bollegraaf Typ HBT 1216 Year of construction 2009 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Pgedpfx Asxrta Ejg Dew Weight 16 t Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Comments: The press is currently in operation and is to be replaced by a new machine in the 2nd quarter of 2026. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Year of construction: 1996, Baler including conveyor, wire bins Manufacturer: Bollegraaf Typ: HBC 50A Build in: 1996 Baler weight: 19000 kg Pedpextmyzofx Ag Dsgw Weight conveyor: 6000 kg Engine: 30 kW Vertical binding Number of wires: 5

Condition: excellent (used), Year of construction: 2010, operating hours: 43,433 h, functionality: fully functional, pressing force: 120 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,200 kg, overall weight: 38,000 kg, power: 90 kW (122.37 HP), Good day, We hereby offer you, without obligation, a used baler from the manufacturer Bollegraaf, model HBC 120 S, including a conveyor belt. A special feature of this baler is the cross-tying system with 10 wires. You have the option to tie vertically with 5 wires and, for example, when baling plastics, activate an additional 5 wires for horizontal tying. The following technical data have been taken from the operator's manual and manufacturer brochures, for which we assume no liability for accuracy or completeness. Manufacturer: Bollegraaf Model: HBC 120 S Year of manufacture: 2010 Operating hours: 43,433 hours Main press force: 120 t Drive motor power: 90 kW Feed belt length: approx. 11 m Inclined belt length: approx. 15 m Pjdpsxt Un Tofx Ag Degw Conveyor belt internal width: 1,554 mm Total system installation area: approx. 15 x 30 x 7.7 m Depending on the bulk density of the material to be baled, the machine can process over 30 t/h at 50 kg/m³, for example. An inspection of the complete baling system in operation is possible. We would be pleased if this machine is of interest to you. Your Service Team, Mertens & Frowein GmbH

Condition: ready for operation (used), functionality: fully functional, Bollegraaf gantry crane 30 tons, 32 meters, 10 meters lifting height Pgodpsw S Ea Ssfx Ag Dsw

Condition: used, Year of construction: 1997, functionality: fully functional, machine/vehicle number: 97020-0010, pressing force: 80 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, power: 45 kW (61.18 HP), operating pressure: 250 bar, Equipment: documentation/manual, This baler is sold by Bollegraaf Recycling Solutions. This is a HBC80 baler (45kW) with cross wires and a chain conveyor. Bale press built: 1997 Chain conveyor built: 2015 Baler Bollegraaf HBC80 45 kW Bale dimensions: 1100 x 720 mm 45 kW main motor Intermediate hopper Conveyor chute Control cabinet Schneider PLC Chain conveyor Horizontal floor section: 6000 mm Rise section: 12500 mm (30 degrees) Gooseneck This baler can be inspected in operation until the end of March. Pgedpfsxvh Dyox Ag Dew

Condition: excellent (used), Year of construction: 1998, functionality: fully functional, pressing force: 25 t, filling opening width: 800 mm, filling opening length: 1,050 mm, bale width: 900 mm, bale height: 800 mm, input voltage: 400 V, noise level: 85 dB, power: 18.5 kW (25.15 HP), volume flow: 160 m³/h, Bollegraaf HBK25 offered in Cyprus. The machine is in good condition and includes a floor conveyor belt. The machine is immediately available. Psdsxbdguspfx Ag Dsgw Technical specifications of the baler: Drive: 18.5 kW Bale size: 800 x 900 x adjustable Feed hopper dimensions: 1,050 x 800 Press force: 25 tons Capacity: 160 m3/hour (depending on material) Technical specifications of the conveyor belt (approximate): Length on floor: 3,000 mm Diagonal length: 5,000 mm

Condition: excellent (used), Year of construction: 2017, operating hours: 13,284 h, functionality: fully functional, pressing force: 140 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,500 kg, oil tank capacity: 2,600 l, Technical data baler: Manufacturer Bollegraaf Type HBC 140 Year of construction 2017 Working hours 13,284, as of October 2025 Press power main press 140 tons (max. 153,5 tons) Press power of pre-press 70 tons Feed channel 1,600 x 1,100 mm (l x w) Capacity per cycle time 4,34 cbm Theoretic cycle time 16 sec. Bale size 1,100 x 1,100 mm (w x h), length adjustable Driving motor 2 x 75 kW Connected load 209 kW Tying system 5-fold vertical, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx. 30 tons/h bulk weight of 50 kg/cbm approx. 46 tons/h bulk weight of 100 kg/cbm approx. 82 tons/h Bale weight 850 up to 1.500 kg Hydraulicoil 2.600 l Univis N46 Baler dimensions with conveyor built up with hopper approx.13,200 x 24,200 x 7,333 mm (l x w x h) Transport dimensions only baler approx.13,200 x 2,884 x 3,539 mm (l x w x h) Machine weight baler approx. 51,810 tons Technical data feeding and elevating conveyor with gooseneck: Manufacturer Bollegraaf Typ HBT 1216/1800 * 23,300 30°/15° Year of construction 2017 Driving motor 7,5 kW Length feeding conveyor 6,750 mm Pgodpfxjxpxhvj Ag Dow Length elevating conveyor 14,400 mm Length goose neck 2,150 mm Grade 30° Effecting width 1,754 mm Height of side wall feeding conv. 500 mm Height of side wall elevating conv. 800 mm Transport dimensions feeding conveyor with one segment elevating part 9,816 x 2,500 x 2,242 mm (l x w x h) Transport dimensions elevating conveyor with goose neck 13,472 x 2,800 (without motor) x 2,729 mm (l x w x h) Pit dimensions 10,000 x 3,200 x 1,200 mm (l x w x d) Condition: The press is in very good condition and ready for immediate operation. The conveyor belt chain needs replacing. The system will be in operation until December 2025. Scope of delivery: baler with conveyor belt, maintenance platform, access ladder, two wire feed stations for 5 wire reels each (without wire), and bale slider. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Year of construction: 1994, condition: not inspected (used), Portalkran 1x8 ton 12 meter 8 ton hoistingheight 10m Pgjdjgmdm Nopfx Ag Djw

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: HBC 140 2x75kW 2001 (210-008-01), pressing force: 155 t, bale weight: 1,500 kg, pressure: 250 bar, power: 150 kW (203.94 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, Psdpfx Agotvau Aj Dogw • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, input current: 238 A, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Pgsdpfovf E Avsx Ag Djw Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2003, functionality: fully functional, machine/vehicle number: W230-028, pressing force: 80 t, warranty duration: 24 months, pressure: 250 bar, power: 45 kW (61.18 HP), year of last overhaul: 2024, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC80 (45kW) with crosswires. Pjdotvat Tepfx Ag Degw At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. After refurbishment, this baler is sold with a 2-year warranty.

Condition: excellent (used), Year of construction: 2004, operating hours: 34,480 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 19,000 kg, transport height: 3,300 mm, oil tank capacity: 750 l, power: 45 kW (61.18 HP), Technical data baler: Manufacturer Bollegraaf Typ HBK 100 Year of construction 2004 Hours of operation 34,480 hours Press power main press 100 tons Press power of pre-press max. 42 tons Feed channel 1,600 x 1,100 mm Filling volume 3.15 m³ Theoretic cycle time 22 sec. Theoretic throughput capacity up to 450 m³/hour Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical, fully automatic Podpfx Ajxbgnhsg Djgw Throughput rate at a bulk weight of 30 kg/cbm approx. 13 tons/hour bulk weight of 50 kg/cbm approx. 20 tons/hour bulk weight of 100 kg/cbm approx. 30 tons/hour Throughput rate with ruffler approx. 20 tons/hour Bale weight 550 up to 750 kg, depends on material Volume hydraulic oil tank 750 l SPS controller Telemecanique TSX Micro Transport dimensions only baler 10,900 x 2,320 x 3,300 mm (l x w x h) Machine weight baler approx. 19 tons Comments: Unlike the standard HBC press series from Bollegraaf, this machine does not have a pre-press flap but cuts the material between blades on the press ram and the counter blade in the frame. This makes it a cutting edge press, similar to a Paal, unoTech, etc. The press is in very good condition for its age, as it was used exclusively for compressing paper from document destruction. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2008, operating hours: 23,000 h, machine/vehicle number: 00834, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,315 mm, bale width: 1,100 mm, bale height: 720 mm, warranty duration: 3 months, power: 30 kW (40.79 HP), year of last overhaul: 2025, Equipment: documentation/manual, Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler, hereby offers the following machine(s) A repaired HBC60 (30kw) Repaired – in very good technical condition Year of construction: 2008 Volume capacity m3/hr max. 365 334 321 301 Volume weight kg/m3 max. 15 30 50 80 Weight capacity T/hr max. 5.5 10 16 24 Bale weight 400 – 800 kg, depending on S.G. of material and bale length Bale length - adjustable Bale height - 720 mm Bale width - 1100 m Filling opening - 1100 mm x 1320 mm Max. size supply - 1500 mm x 1200 mm Pressure force ram - max 60 tonf. Pressure force pre-press flap - max 25 tonnes Cycle time - 18 seconds Pgsdsxck U Uopfx Ag Djw Motor - 45 kW Motor Twistomat - 2.2 kW Motor counter pressure pump - 1.1 kW Following repairs have been done in our official Bollegraaf OEM Refurbishment Workshop: * Safety doors needle installation replaced with new * Ram wheels behind replaced with new * Bronze strip above ram replaced with new * Movable beam position switch ram replaced with new * Scraper above ram replaced with new * Sealing pre press cylinders replaced with new * New steel beams channel cylinder * nieuwe buisjes oplassen en wielen gangbaar maken * New pusher cylinder underneath vertical tying unit * Safety hatch behind needle installation replaced with new * Several cables and asi modules replaced with new * New air filter * New oil filters

Condition: reconditioned (used), Year of construction: 2000, operating hours: 32,169 h, functionality: fully functional, pressing force: 60 t, filling opening width: 1,100 mm, filling opening length: 1,320 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 750 kg, overall weight: 22,000 kg, oil tank capacity: 900 l, For sale is a complete baling system consisting of conveyor technology, baling press and wire stations. Technical data baler: Manufacturer Bollegraaf Recycling Machinery B.V. Typ HBC 60A Year of construction 2000 Hours of operation 32,169 hours, stand November 2024 Press power main press 60 tons Press power of pre-press max. 25 tons Feed channel 1,320 x 1,100 mm Theoretic cycle time 18 sec. Bale size 1,100 x 720 mm, lenght variable Driving motor 45 kW Connected load 60 kW Tying system 5-fold vertical Throughput rate at a bulk weight of 30 kg/cbm approx. 5,5 tons/hour bulk weight of 50 kg/cbm approx. 10 tons/hour bulk weight of 100 kg/cbm approx. 16 tons/hour Bale weight 400 up to 750 kg, depends on material SPS controller Telemecanique TSX Micro Machine weight baler approx. 24 tons Scope of delivery: 1 piece chain belt conveyor Pgodpoviwdmjfx Ag Dsw 1 Bollegraaf HBC 60A baler with whirling unit 1 maintenance platform with access ladder 2 wire stations with deflection rollers for 10 wire reel stands (without wire) The following repair and overhaul work was carried out: Hydraulic oil tank emptied, cleaned and refilled with new oil Oil filter and air filter replaced Hydraulic block partially resealed Hydraulic hose on hydraulic block replaced Wire entry marks on the floor passages welded shut and smoothed Tying unit cleaned, serviced Electrical system repaired, door flap contact switch partially replaced Whirbulator repaired General maintenance work carried out, lubricated Machine tested during operation, without the use of materials, in manual mode and in automatic mode, see function video Comments: The system has already been completely dismantled, stored and is available for loading at short notice. The documentation (BA, CE, electrical/hydraulic circuit diagram) is available. Viewing is possible by appointment. We accept no liability for the technical details or any errors.

Condition: reconditioned (used), Year of construction: 2014, operating hours: 24,967 h, functionality: fully functional, machine/vehicle number: 004283-0030, pressing force: 122 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, warranty duration: 24 months, year of last overhaul: 2026, Equipment: documentation/manual, Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler. This is a baler HBC120s (90kW) with crosswires. At the time of writing this baler is being completely refurbished in our refurbishment workshop. This refurbishment takes place on the basis of the very strict Bollegraaf OEM Refurbishment Guidelines. Pgsdpexcir Esfx Ag Dsw After refurbishment, this baler is sold with a 2-year warranty.

Year of construction: 2003, operating hours: 43,000 h, condition: repair required (used), machine/vehicle number: HBC 140 2x75kW 2003 (W230-005), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2003 Hardox bottom floor plate only Plastic valve Anti-rat cabling Hours 43.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. Pedokcgynspfx Ag Degw The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2008, operating hours: 40,000 h, condition: good (used), machine/vehicle number: HBC 140 2x75kW 2008 (00191), Sold by Bollegraaf Recycling Solutions, the original manufacturer of this Bollegraaf baler and conveyor: Pgodpfx Agokcgf Hj Dow Bollegraaf HBC140s Baler (2x75kW). Baler: Weight: 47.100 kg Construction year: 2008 Hardox bottom floor plate only Variable channel pressure control Plastic valve Hydraulic pump driven by frequency inverter Anti-rat cabling Oil in-depth filtration Modem Hours 40.000 This baler can also be sold fully refurbished according to the 'Bollegraaf OEM Certified Refurbishment standards'. This includes 2 year guarrantee. Contact us for more information or a quotation. General principles of refurbishment Cleaning & disassembly Before the actual refurbishment takes place the baler is completely cleaned and disassembled in our refurbishment workshop. Tolerances After the disassembly the tolerances of all steel components are measured and re-welded where necessary, this at least applies to the following components; • Ram, • Frame, • Channel, • Pre-press-flap After disassembly and inspection the ram is welded-up again and fitted with new ram wheels. The protective grids and the pre-press flap are made dent-free and repaired where necessary. Repainted After measuring the tolerances and any repair- and welding work, all components are being blasted and coated again. Hydraulics: The hydraulic tank is cleaned. The hydraulic lines & hoses are replaced. The hydraulic components are repackaged. The hydraulic oil is replaced. Cabling: All cabling is checked and replaced if necessary. All junction boxes are replaced and placed back in easily accessible positions. Wear parts: All wearing parts are replaced. The pins and shafts of the cylinders and the channel are replaced with new ones. All wearing parts of (both) needle installations and knotters are replaced for new. Cylinders: The cylinders are repackaged and, if necessary, provided with a new chrome layer or a new cylinder rod. MCC Cabinet The switch box is checked and cleaned. If necessary, electronic components are replaced with new ones. The PLC and HMI (human interface) are replaced with the latest Schneider M340 version including the latest software.

Year of construction: 2022, operating hours: 3,863 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 006682, On behalf of our customer, we hereby offer a virtually new OI sorting. This installation can be tested in operation at the customer. The machines consist of; Sorting oi: Pjdpjwq D Dnefx Ag Dogw 0050 Bunker belt with dosing drum BDF1200/2000*10000 0060 Ascending belt to screen HBT1200/1600*14000 0070 Cardboard screen 1640*7000 Platform Cage ladder 0080 Adjustments to existing paper chain belt 0090 Switch cabinet included Operating hours only 3863 In consultation with the customer and Bollegraaf, a guarantee is possible under certain conditions See the attached PDF for a precise technical description per machine