Used Automatic Sanding Machine for sale (74,401)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides Giodpfxst Tqy Eo Acwsr pressure rollers. Safe transport of profiled workpieces on ca...

Condition: used, Year of construction: 1997, functionality: limited functionality, - Oscillation defective - Main switch replaced - Machine is operational - Sold without warranty Gsdsyi Ug Ajpfx Acwoir

Condition: used, machine/vehicle number: 007968, Max. panel width: 300 mm Max. panel length: 2500 mm No of Bottom Units: 6 Gjdpfewu Abaex Acwsir Lateral horizontal groups: yes

Condition: used, Year of construction: 2020, Packaging Machine Fully Automatic Side Sealing Machine Profi Packer Manufacturer: Schlichter Model: SCV 400 Pro Year of manufacture: 2020 Longitudinal sealing: continuous Photoelectric sensors: horizontal and vertical (standard) Compressed air: 6 bar Conveying speed per minute: min. 5 meters, max. 30 meters Film core Ø: 76 mm Max. film roll Ø: 350 mm, with optional film folding device up to 700 mm! Max. film roll width: 650 mm Sealing bar width: 300 mm Product width min. and max.: 50 mm to 410 mm Product height min. and max.: 1 to 250 mm Product length min. 50 mm, max. unlimited Film thickness: from 7 to 80 μm Film material: Polyolefin shrink films, Polyethylene, PVC; PLA and other bio-films Cycles per minute: up to approx. 85 cycles Gedpoxuglmofx Acwsir Machine dimensions (L x W x H): 2,200 x 1,680 x 1,800 mm Weight: 800 kg Shrink Tunnel: Model: SCT 400U Year of manufacture: 2020 Pass-through width: 450 mm Pass-through height: 280 mm Heating power: 14 kW Dimensions (L x W x H): 2,065 x 1,065 x 1,340 mm

Condition: used, used 2-belt sander 1x with continuous pneumatic pressure feed 1x sanding unit 100 mm vacuum clamping device Gijdpfx Acsyvvr Uswsr Manufacturer: Heesemann Type: BA2 Machine no. 7304051 Motor: 7.5 / 11 kW Sanding length approx. 2550 mm Sanding width approx. 100 / 150 mm Belt length approx. 8500 mm Table size approx. 2550 x 1350 mm Throat (right) approx. 600 mm Upper belt cover Table lighting Vacuum clamping device with pump 9 vacuum suction plates Belt speeds 710 / 1430 m/min Sanding shoe 2450 mm Extraction connection D 180 / 250 mm Required space approx. 4500 x 1400 x 1800 mm Weight approx. 1500 kg Total connected load approx. 12.5 kW Location: 97447 Gerolzhofen, loaded free on truck, unpacked Delivery as seen, as inspected, without warranty or guarantee

Condition: used, Year of construction: 2000, used, top equipment, excellent condition, low hours Manufacturer: Johannsen Model: T94 Year of manufacture: 2000 Machine no.: 22138 CE type tested GS wood dust tested Motor: 5.5 / 0.25 kW Sanding length: approx. 2600 x 960 mm Sanding width: approx. 960 mm Belt length: approx. 7800 x 150 mm Table size: approx. 2790 x 960 mm Throat depth right: approx. 850 mm Electric adjustment Gsdpfxjyvvr Ij Acwjir Upper belt cover Upper sanding support Table lighting Belt speeds: 1434 m/min Right-left travel Belt blow-off Sanding shoe: 300 x 140 mm Extraction connection: D 180 mm Required space: approx. 4000 x 1500 x 1500 mm Weight: approx. 1000 kg Total connected load: approx. 5.7 kW Location: 97447 Gerolzhofen, free loaded, unpacked Delivery in as-inspected condition, without warranty or guarantee

Condition: used, Year of construction: 1997, Automatic in-line filling machine: Model: Bosch FLK 6040 CIP Year : 1997 Power: 5 kW Speed: 30-40 bottles/min Conveyor width: 8 cm Transporting bottles from right to left Linear dosing system with 6 stainless steel pistons Filling point: 6 heads Plunger filling head: yes Volume: from 15 to 500 ml Pistons replaced in 2012. Filling accuracy: +/- 0.5% depending on the product Product: liquid/semi-liquid for bottles, flasks, cans Formats : ⌀ 41 to 115 mm Hauteur max : 320 mm Minimum internal diameter of opening: 5 mm Closed hopper Clean-in-place (CIP) module Maximum temperature: 60°C Dimension : 400 x 150 x 320 cm Weight : 2100 kg Several formats and spare parts available.   Capping/screwing machine: Model : VLM 7010 Year : 1997 Power : 10 kW Giedpsyfw H Rofx Acwer Transporting bottles by conveyor belt. Direction from right to left. Screw, pressure or push-fit sealing system Capacity : 60 units / min Bottle dimensions: Width: 16 to 90 mm Length: 16 to 135 mm Height: 40 to 280 mm Diameter: 16 to 100 mm Cap dimensions: screw cap: Diameter : 16 à 60 mm Height : 13 à 50 mm Width: 16 to 60 mm Length: 16 to 60 mm pressure cap: Diameter : 16 à 60 mm Height : 13 à 50 mm Width: 16 to 60 mm Length : 16 à 70 mm Machine dimensions: 400 x 130 x 200 cm (+ electrical cabinet 160 x 50 x 170 cm) Weight : 2050 kg  

Condition: excellent (used), functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, DGUV certified until: 03/2027, type of input current: three-phase, Lye Coating Machine Drautz RD 100 Compact design One-person operation & easy cleaning Godpexmrbdjfx Acwsir Double lye curtain With stripping unit Connection: 400V, 16A CEE plug Used machine With warranty & spare parts service Quality from a specialist company! Benefit from over 35 years of experience! Options: Maintenance contract Service package Salting unit Delivery service Spare parts box for increased safety Training & commissioning Visit our extensive selection!

Condition: used, Rotary indexing table, rotary indexing table with 16 stations Rotary indexing machine + TOX hydraulic press Special rotary indexing machine with multiple assembly stations Production and assembly line with rotary indexing system From special machinery manufacturer "AKE-technologies GmbH" Serial number: Order number: 11111 Year of manufacture: 2012 - large rotary indexing table WEISS type TC500, with 16 stations - pressing station with TOX power pack Godogd D U Ejpfx Acwsir - vibratory feeder - conveyor belts - testing stations - some stations still visible in the photos but already dismantled Required space L x W x H approx. 3500 x 2750 x 2300 mm Net weight approx. 3000 kg All in as-new condition – the system was never used in series production.

Condition: used, Semi-automatic tube bending machine, mandrel tube bender MOBITEC type BAH 1-2 KOTTMANN und BERGER GmbH Serial No. Year of construction for simultaneous bending of two steel tube sections up to Ø 12 mm Bending angle max. 90° Tube diameter max. 12 mm Mandrel length approx. 65 mm Rated power 3.5 kW Compressed air max. 6 bar / approx. 1 litre per bending cycle Power supply 400 Volt, 50 Hz - Pneumatic clamping - Pneumatic mandrel retraction - Angle input control via STÖBER Controlbox Series 4000/5000 - SIEMENS S7-200 control with TD200 display - Machine without bending tools and without tool storage pins 25 x 183 mm Godpfx Aspu R Nvscwoir - Only 1 bending mandrel available (see pictures). Required space (L x W x H) 1000 x 1000 x 1500 mm Weight 390 kg Good condition

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Giodpfedzqltex Acwsr Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition

Condition: used, Year of construction: 1984, Used machine Year of manufacture: 1984 Giodpfx Acsw R Hh Uewer Condition: fully checked and serviced Equipment and technical data: - Incl. combination unit with contact roller and sanding pad - With height-adjustable contact roller for calibration - With air cushion pressure shoe controlled by the workpiece - 4-way adjustable grit compensation - With pneumatic belt tensioning device - With rotating structuring brush at the machine's outfeed side - Sanding width: 1350 mm - Sanding belt length: 1900 mm - Pass-through height: 150 mm - Main motor: 15 kW - Feed speed steplessly adjustable 2.5 - 12.5 m/min - With roller table at the infeed - With separate additional structuring brush - With roller table at the outfeed - With digital display unit for the electromotoric workpiece thickness setting - With automatic workpiece thickness adjustment - Extraction ports: 2 x 200 mm - Feed belt is ok; has a defect in one spot (see photo) Dimensions: approx. 2300 x 2000 x 2300 mm Weight approx.: 2500 kg Pictures show the machine in unchecked condition! Availability: short-term Location: Röllbach

Condition: used, Welding turntable – Welding positioner with enclosure Circular welding device Load capacity approx. 50 kg Chuck diameter 300 mm Chuck rotational speed 1.0–15 rpm Power supply 230 Volts, 50 Hz - Spiral scroll chuck with internally stepped jaws - Infinitely variable speed adjustment via potentiometer - Drive via geared motor, rotation direction left - Start via electrical switch - Welding current transmission via slip ring contact - Extraction connection Ø 160 mm - Internal lighting Door opening W x H 715 x 1060 mm Internal dimensions W x D x H 780 x 780 x 1100 mm Required space W x D x H 900 x 900 x 2300 mm Gjdjdzp U Iopfx Acwsir Weight 190 kg

Condition: used, Year of construction: 1991, EDGE SANDING MACHINE LZK 4: Langzauner edge sanding machine LZK Machining and sanding of all types of wood, also in combination with plastics Year of manufacture: 1991 Motor power: 3 kW Belt speed: 22 m/sec Belt dimensions: 3000 x 200 mm Table size: 1250 x 350 mm Height adjustment range: 200 mm Extraction port diameter: 110 mm Minimum air speed: 20 m/sec Extraction capacity: 700 m3/h Gjdjw A Aa Eopfx Acwoir Total weight: 450 kg Total connected load: 3.2 kW Operating voltage: 3 x 380 V 50Hz Required space: 1900 x 900 mm All technical data and information as per brochure

Condition: excellent (used), CATALOGUE NUMBER 7928 TECHNICAL DATA - Max. workpiece height: 120 mm - Max. workpiece width: 1900 mm - Top unit with 6 brushes - Unit adjustable up/down - Oscillating unit - Rotating star-shaped sanding unit arrangement - Infinitely adjustable brush speed via inverter - Infinitely adjustable feed, rotation, and oscillation speeds - Main motor: 7.5 kW - Vacuum table - Two vacuum pumps: 2×7.5 kW - Pump dimensions: 1100x800x940 mm - Extraction port diameter: 4x150 mm, 4x200 mm - Overall machine dimensions (L/W/H): 2850x2100x2400 mm - Weight approx. 2500 kg ADVANTAGES – Two vacuum pumps – With oscillation – Rotating aggregate – German-made – Unpainted – Original DTR documentation – Used sander, very good condition Net price: 45,900 PLN Net price: 10,900 EUR Net price calculated at an exchange rate of 4.2 PLN/EUR Giodpfxoyu Tmlo Acwsr (In case of major exchange rate fluctuations, the price may change)

Condition: excellent (used), Belt sander Make Karnasch Type ALMI AL 100 with 6 different contact rollers or sanding rollers Diameter : 17,5 - 20 - 22 - 28 - 38 - 48 mm Gedjuf N Scopfx Acwsir belt width 100 mm length 2000 mm Grinding range for grinding diameter 20 - 76 mm

Condition: new, Year of construction: 2022, Bandwidth: 150mm Belt length: 3000mm Table size: 960mm x 352mm Additional table: 330mm x 330mm veneer sanding device: yes Oscillation: yes sanding unit swivels: yes Giodpfxjgr Ufho Acwsr suction connection: 120mm Motor power: 3 kW Machine length: 1900mm Machine width: 810mm Weight: 290kg

Condition: as good as new (ex-display), Year of construction: 2022, Strip width: 150mm Belt length: 2170mm Table size: 1440mm x 710mm veneer sanding device: yes oscillation: yes Table tilting: yes, 0°÷ 45° Suction connection: 120mm Motor power: 3 kW Machine length: 1440mm Machine width: 800mm Weight: 530kg Giedpshpmahjfx Acwor

Condition: as good as new (ex-display), Year of construction: 2022, Strip width: 150mm Belt length: 2400mm veneer sanding device: no oscillation: yes roller diameter: mm grinding unit swiveling: yes / 90° - 0° Work table: 730 x 300 mm additional table: 420 x 400 mm Belt speed : 14 m/sec. m/sec. Suction connection : 120mm Gisdpfx Aohpmadscwjr Motor power : 1,8 kW / 400V Machine length: 1480 mm Machine width: 680 mm Weight: 160 kg

Condition: new, Year of construction: 2022, Strip width: 150mm Belt length: 2740mm veneer sanding device: no oscillation: yes roller diameter: 115 mm Grinding unit swivels: yes / 90° - 0° Gsdpfx Ashq A H Docweir worktable: 900 x 305 mm additional table: 290 x 260 mm Belt speed : 16 m/sec. m/sec. Suction connection : 100mm Motor power : 3 kW / 400V Machine length: 1540 mm Machine width: 750 mm Weight: 220 kg

Condition: new, Year of construction: 2022, Bandwidth: 150mm Belt length: 3000mm Table size: 960mm x 352mm Additional table: 330mm x 330mm grinding roll diameter: 60mm / 100mm / 120mm veneer sanding device: yes Oscillation: yes sanding unit swivels: yes suction connection: 120mm Motor power: 3 kW Machine length: 1900mm Giedsgtdpujpfx Acwer Machine width: 900mm Weight: 310kg

Condition: used, CNC Lathe DMG MORI SEIKI - GILDEMEISTER Type CTX 310 ecoline Machine No. 8044001846E Year of manufacture: 2013 CNC Control: SIEMENS Sinumerik 840D sl Swing diameter over bedway cover: 330 mm Swing diameter over cross-slide cover: 260 mm Centre height max.: 190 mm Centre distance max.: 580 mm Turning diameter max.: 200 mm Longitudinal slide travel (Z-axis) max.: 450 mm Cross-slide travel (X-axis) max.: 160 mm Spindle bore through draw tube: 51 mm Spindle bore through front bearing: 100 mm Spindle speed max.: 5,000 rpm Feed rate X and Z: mm/min. Rapid traverse X-axis: 30 m/min. Rapid traverse Z-axis: 30 m/min. Feed force X and Z: 4,500 Nm Tool turret: 12 stations Driven tool stations: 6 stations Tool holder cylindrical VDI 30 mm Spindle drive motor power at 100% duty cycle: max. 11 kW Spindle drive motor power at 40% duty cycle: max. 16.5 kW Power supply: 400 Volt, 50 Hz, 21 kVA - CNC control SIEMENS Sinumerik 840D sl, system software NCU V04.04+SP02+HF02 - Controlled C4-axis chuck position and C1-axis for tool turret - 3-jaw chuck AUTOGRIP Ø 210 mm with 1 set of hard jaws and 15 sets of soft jaws - AUTOGRIP hydraulic hollow clamping device - Clamping force adjustment for regulating clamping pressure - Tool turret SAUTER, type 0.5.901.020 with 12 stations (6 driven) - 20 tool holders VDI 30 - Tailstock MK 4 Godeyk Hrgopfx Acweir - Indirect measurement system via rotary encoder - Chip conveyor with integrated coolant system - Workpiece residual life display and piece counter as large display on machine enclosure - Control cabinet cooling unit - 9,716 total operating hours (main switch on), of which 3,322 spindle hours as per counter - Operating instructions and manuals Machine footprint with chip conveyor (L x W x H): 4,500 x 2,600 x 2,050 mm Base machine space requirement (L x W x H): 2,900 x 2,150 x 2,050 mm (3,200 kg) Chip conveyor space requirement (L x W x H): 3,350 x 850 x 1,650 mm (500 kg) Weight: approx. 4 tons Very good condition

Condition: excellent (used), Year of construction: 2005, functionality: fully functional, table length: 2,500 mm, table width: 1,250 mm, Available: medium-format Trumpf CNC punching machine, complete with SheetMaster, SortMaster Box Linear Special, and GripMaster. All functions available: multi-tool, threading, high-speed marking, SoftPunch. Punching force: 220 kN, max sheet thickness: 8 mm, X/Y travel: 2535 mm / 1280 mm, max workpiece weight: 200 kg, X/Y feed rates: 100 m/min / 60 m/min, simultaneous: 116 m/min, punching/marking rate: 1200/min / 2800/min, C-axis tool rotation: 330 rpm. Machine dimensions X/Y: approx. 6800 mm / 6100 mm, weight: approx. 15,000 kg, operating hours: approx. 58,000 h. Documentation available. On-site inspection possible. Offers and videos of the plant in operation can be provided upon request. Godpfxoywg Agj Acweir

Year of construction: 2022, condition: used, Number of sanding units 6 st. Gedpfxoynntto Acwsir Sanding height max. 120 mm output 12 kw

Condition: like new (used), functionality: fully functional, AUTOMATIC EDGE SANDING machine with 3 units , model TONELLI OTB.15 ( made in ITALY ) second hand machine working condition: Excellent, like new CE regulation: YES Voltage: 380/50 for sanding panel edges, on raw and painted edges, flat and shaped, solid, veneered, profiles, frames and various technical data: electric working height adjustment minimum working height: mm.3 maximum working height: mm.100 minimum working width: mm.60 track feed speed adjustable from the control panel: from 5 m/min to 30 m/min track feed with rubber pads and adjustable rubber pressure wheels feed track motor power: 2 HP machine composed of 3 independent units: 1° Unit : Tilting oscillating sanding unit - Pneumatic pad - Motor 2 speeds Hp 1,9 / 3,3 - Automatic group entry - Belt cleaning blower 2° Unit : 45° oscillating sanding unit - Pneumatic pad - Motor 2 speeds Hp 0,6 / 1,2 - Automatic group entry - Belt cleaning blower 3° Unit : 45° oscillating sanding unit - Pneumatic pad - Motor 2 speeds Hp 0,6 / 1,2 - Automatic group entry - Belt cleaning blower Removable support for panel support Installed power: 10 kW Overall dimensions: 3600 x 1600 x 1600 mm Gedpfx Aceywzchswjir Weight: 2000 kg