Used Hess Hydro-Spezial for sale (916)

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission Dsdpfjt Tqy Eex Am Rsch the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: excellent (used), Year of construction: 1995, Rotary / carousel wood gluing press HESS, 6 meters Year of manufacture: 1995 The press is operational and in good technical condition. Press infeed • Glue application machine with 2 rollers Technical data of the HESS gluing rotor Dcsdpfx Asy Rzk Som Roh • 4 working areas, each 6,200 x 1,000 x 150 mm • 4 pressing sections • 8 sliding pressure beams • 2 pneumatic pressure cylinders per each pressure beam • 21 hydraulic rams from above • Pressure force per cylinder: 35,000 N / 3,500 kg • Maximum total pressure at 120 bar: max. 73.5 tons per pressing surface Machine dimensions • Total length: rotor 11,100 mm • Depth: 3,050 mm • Height: 3,350 mm • Weight: 13,500 kg

Condition: good (used), Wood router bit, router head, router tool, wood router bit, profile router bit Dcodpfxjcazr As Am Reh -AKE wood router bit with: AKE Hydro-Grip -Outer diameter: 165 mm -Height: 60 mm -Hole: Ø 40 mm -Cutter: 1 -Price/Sale: complete -Weight: 8 kg

Year of construction: 1999, condition: used, hydraulic lockbolt rivet gun, rivet gun, blind rivet gun -hydraulic lockbolt rivet gun -without: storage container Dcedpjdlw Dtofx Am Rsh -incl.: hydraulic unit and control -Dimensions: 1230/800/H1300 mm -Weight: 450 kg

Condition: used, Wood milling cutter, milling head, milling tool, wood milling cutter, profile milling cutter -Wood cutter: with ETP Hydro-Grip -Outer: Ø 180 mm -Height: 46 mm -Socket: Ø 40 mm -Number: 2x milling cutters available Dcsdpfx Ascazrvem Reh -Price: per piece -Weight: 10 kg

Condition: used, Hydraulic cylinder, synchronous cylinder, steering cylinder Dcsdpfx Amodkf I Ts Roh -Piston diameter: 38 mm -Piston rod: Ø 16 mm (M12 thread) -Stroke: 20 mm -Dimensions: 234/89/H50 mm -Weight: 3 kg

Condition: good (used), Cup hinge drilling machine -Stops: pneumatically controlled with program selection Dcjdpfx Aeb A Hkysm Reh -Drilling pattern: see the pictures -Dimensions: 4000/1100/H1800 mm

Condition: used, Year of construction: 2022, functionality: unexamined, machine/vehicle number: SA-####-116, Used Hydro Vasli stainless steel hydraulic hand pump Manufacturer: Hydro Vasli Dcsdpsw Hc Ecsfx Am Reh Model: SA-####-116 (Handpump HFC) Weight: ~27kg

Condition: used, Air tube bundle extractor, air tube bundle assembly station for heat exchangers, cooling coil, cooling pipe, cooling spiral, tube bundle heat exchanger Dedpfsw Ty Dnex Am Rech -Handover: in its current condition as inspected (without documentation) -Condition: Diesel engine currently out of service -Air tube bundle extractor: Hydro-Extractors INC -Type: 504- Diesel -Dimensions: 8400/1900/H2850 mm -Transport dimensions: 8400/1900/H1700 mm -Weight: 6860 kg

Year of construction: 2024, condition: new, Punching knives eroded from solid steel Our punching knives are manufactured from selected steels and are available in a wide range of geometries and standards of all types such as ISO, DIN, JIS, ASTM, IEC. They are characterized by: - competent steel selection - material specific cutting geometry - optional equipment with various specimen ejectors and clamping spigots - individual production in different heights possible - also possible as multicutter - long tool life - excellent cutting finish - optimal cutting results Dodpfx Amskkhkue Rjch - suitable for every type of press e.g. manual toggle presses, pneumatic and hydropneumatic presses

Condition: like new (used), Year of construction: 2018, machine/vehicle number: STHP 80KN, functionality: fully functional, pressing force: 8 t, table width: 300 mm, total length: 200 mm, total width: 510 mm, total height: 1,320 mm, overall weight: 110 kg, 1 Hydropneumatic press type STHP 80 kN Bmcbfntr Dsdot Rhb Iepfx Am Rech with two-hand operation - floor model with and base frame The compact and handy table model has a hydropneumatic drive with pressure intensifier, which can increase the punching force by up to 5 times. The punching cylinder is pressurized with oil by the pressure intensifier during the working stroke and therefore has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders.

Condition: good (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: H50KS, tractive force with load: 50,000 N, Universal testing machine, type H50kS up to 50KN for tension and compression Load cell 50KN 10KN 1KN and Windows software 8-9-10-or 11 for tension, compression, bending, shear etc., according to EN ISO 7500-1, ASTM E4 The H50kS is a universal testing machine developed according to the latest standards. The machine operates in accordance with the relevant radiation protection and safety directives in the EC. (EN 50081-1, 72/23/EEC, EN 61010-1) The maximum voltage within the machine is 48 volts. Special features - large, easy-to-read liquid crystal display with backlighting - Graphical or numerical display mode - alpha-numeric file input - speed range 0.001 to 500 mm/min. - high return speed 0.001 to 500 mm/min. - exact crosshead positioning - Robust load frame - Output report of results with mean value and standard deviation via printer - Large selection of test software under Windows for various standards - RS232 interface mode for use with computer system - Accuracy of load cell force display 0.5 % over the entire range - Displacement display accuracy 0.001 mm - Equipped with a force and displacement alarm system Djdpfxoq Ruw Nj Am Roch - 32bit motor controller - 20% digital weight blanking during load cell capacity check - Automatic motor alarm in case of over or under voltage and overheating Specifications: - Force measurement accuracy +/- 0.5 % of the displayed force in the range 2% to 100% - Accuracy of position measurement +/- 0.01 % or 0.001 mm - Speed accuracy +/- 0.005 % of the selected speed - Operating temperature 0 to 38°C - Humidity range 10% to 90% Technical data: - Two-spindle table model - maximum load 50kN in tension and compression - maximum stroke 1100 mm without clamping fixtures - for further details please refer to the brochure Dimensions: Height: 1613 mm width: 720 mm Depth: 500 mm Weight: 140 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Condition: used, Year of construction: 2009, functionality: fully functional, 1 Universal Testing Machine Type H 10 KM Used device with Windows 11 software for tensile, compression, and bending tests; comes with one pair of wedge grips up to 10 kN and a certificate for tensile and compression displacement measurement. For testing in tension, compression, shear, bending, etc. • This is a dual-spindle benchtop model. • The machine complies with DIN 51220 and 51221, Class 1. • Digital display for force and displacement, 4½ digits, with peak value memory. • Five-range automatic switching for force and displacement measurements. • Digital speed adjustment from 0.5 to 1000 mm/min in increments of 0.1 mm. • Break detector and automatic return function are standard features. • Driven by a precision servo motor with high-frequency chopper control unit and digital feedback for load-independent, constant speed. • Quiet operation thanks to toothed belt drive and ball screw spindles with bellows cover. • Fully computer-controllable via RS 232 interface. Max. load: 10 kN in tension and compression Max. travel: 1150 mm without grips Force measurement: Strain gauge Measurement principle: Temperature-compensated Dcodpfx Amoxghlfo Roh Displacement measurement: Built-in optical encoder, 0.01 mm resolution Power supply: 220-250 V, 50-60 Hz Power consumption: 1.0 kW Dimensions: Height 1575 mm, Width 635 mm Clear width of frame: 410 mm Weight: approx. 95 kg Includes: 10 kN load cell and certificate for force and displacement.

Year of construction: 2024, condition: new, Super Dumbbell – the ultimate punching knife with replaceable precision cutting blades Super Dumbbell has a spring type ejector, is equipped with 5 sets of precision spare blades and therefore represents a set of six punching knives in total. It is ideally designed for manual and pneumatic presses. Excellent price-performance-ratio “6 knives for the price of 1” Replaceable precision cutting blades • Japanese carbon steel: ultra-hard – ultra-sharp – maximum cut resistance • Easy replacement • No regrinding • No downtime • Ultra-thin symmetrical cutting blades minimize concave test specimen cross sections (Fig. 1) • No more premature tearing of the test bars • Up to 10 % higher tensile strength or elongation at break values • Extremely smooth cut surfaces of test specimens (Fig. 2) • Always available separately Guarantee for: • High-precision test specimens • Reliable and reproducible test results Djdpfx Ameki Tqcj Rjch Ideally suited for: • High polymer materials such as rubber, plastics, etc. • Standards of all kinds, such as ISO, DIN, JIS, ASTM, IEC, etc.

Year of construction: 2024, operating hours: 5 h, condition: as good as new (ex-display), 1 Hydropneumatic press type STHP 60 kN Dcodepn Unvjpfx Am Rsh with two-hand operation - floor model with and without base frame The compact and handy table model has a hydropneumatic drive with pressure intensifier which can increase the punching force up to 5 times. During the working stroke, the punching cylinder is pressurised with oil by the pressure intensifier and thus has a purely hydraulic punching stroke. The return stroke is performed directly with compressed air. The adapter that can be screwed into the piston rod of the working cylinder makes it possible to install special tool holders.

Condition: refurbished (used), Year of construction: 2012, operating hours: 100 h, functionality: fully functional, machine/vehicle number: H5KS, Universal testing machine, type H5kS extended version by 254 mm With 5KN 500N load cell fixture and WINdows 10-11 software for tension, compression, bending, shear etc., according to EN ISO 7500-1, ASTM E4 The H5kS is a universal testing machine developed according to the latest standards. The machine operates in accordance with the relevant radiation protection and safety directives in the EC. (EN 50081-1, 72/23/EEC, EN 61010-1) The maximum voltage within the machine is 48 volts. Special features - large, easy-to-read liquid crystal display with backlighting - Graphical or numerical display mode - alpha-numeric file input - Speed range 0.001 to 1000 mm/min ( 2.5kN ) speed range 0.001 to 500 mm/min ( 5kN ) - high return speed 0.001 to 1500 mm/min. - Precise crosshead positioning - Robust load frame - Output protocol of the results with mean value and standard deviation via printer - Large selection of test software under Windows for various standards - RS232 interface mode for use with computer system - Accuracy of load cell force display 0.5 % over the entire range - Displacement display accuracy 0.001 mm - Equipped with a force and displacement alarm system - 32bit motor controller - 20% digital weight blanking during load cell capacity check - Automatic motor alarm in case of over or under voltage and overheating Specifications: - Force measurement accuracy +/- 0.5 % of the displayed force in the range 2% to 100% - Accuracy of position measurement +/- 0.01 % or 0.001 mm - Speed accuracy +/- 0.005 % of the selected speed - Operating temperature 0 to 38°C - Humidity range 10% to 90% Technical data: Dedsq Ruygopfx Am Rjch - Single-spindle table model - maximum load 5kN in tension and compression - maximum travel 1004 mm without clamping fixtures - for further details please refer to the brochure Dimensions: Height: 1394 mm width: 490 mm Depth: 450 mm Weight: 102 kg Connection: Machine: 50-60 Hz - 2000 W Power supply: 220/240VAC

Year of construction: 2024, condition: new, machine/vehicle number: H3000-H5000TM, Universal testing machine H3000TM-H5000TM according to DIN EN ISO 7500 The universal testing machine of the H3000TM-H5000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with Dcjdpfx Ameiq Hxko Reh ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor controlled and has a membrane keypad. The 2-line LCD display shows the force and travel. The testing machine can be used as standalone or with a PC via USB interface. The displacement is measured by means of an encoder 0.01 mm visible resolution on LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travels, 500mm or 1200mm (without load cell and testing tool). Further scope of delivery: One load cell up to nominal load, 220 Volt cable, USB cable, description, CE declaration of conformity. For more information, please refer to the attached description. Load cell 3000N-5000N Measuring range: 5-5000N tension and compression, with nom. 2mV/V output signal, overload protection: +/- 1000%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, repeatability: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate Long travel extensometer HE 900mm measuring travel, measuring arms motorized, including electronics Accuracy class class 1 from 1mm travel according to DIN EN ISO 9513 Measuring principle optical incremental Measuring path 900 mm , minus measuring length Display error 6 µm or 2 Resolution 1 µm Actuating force 10 cN Standard initial device measuring length (Lo) 10-100 mm, in 5 mm steps Lo adjustment is manual Measuring arm opening and closing is motorized specimen diameter 0-30 mm specimen thickness 0-30 mm sample width 0-100 mm Weight approx. 32kg Scope of delivery strain gauge complete with electronics Cutting edges round: 1 set each carbide / rubber wear parts measuring blades optional rectangular cutting edges ATTENTION: When using optional cutting edges a readjustment of the lo a readjustment of the lo stop is necessary.

Condition: like new (used), Year of construction: 2024, operating hours: 5 h, functionality: fully functional, Mini Rheometer – Precise Analysis of Crosslinking Behavior The Mini Rheometer is a high-precision testing device for determining the crosslinking behavior of rubber and other crosslinkable polymers. Versatile Application Options ✔ Determination of processing time for resins, cements, and adhesives ✔ Use in the dental industry ✔ Suitable for research, development, and rapid product inspection Efficient & Fast Testing The test duration matches exactly the crosslinking time of 1 g of material at the set temperature. Operating principle: Linear shear deformation according to DIN 53529 Part 1 Innovative Technology for Reliable Results ✔ Hinged measuring chamber with integrated sensor paddle ✔ Fast temperature stabilization due to the small chamber volume ✔ Dynamic measurement using sinusoidal shear loading with low amplitude and frequency ✔ Precise data acquisition via a load cell, connected to modern electronics & software Dedoxzrbaspfx Am Rjch ✔ Display of the crosslinking isotherm & evaluation according to DIN 53529 Part 2 Scope of delivery: Mini Rheometer, software, Windows 11 PC, volume punch

Condition: used, Year of construction: 1986, - 2 pneumatic printing cylinders in length - 2 pneumatic pressure cylinders in width - 2 pneumatic workpiece hold-downs - feed belt width: approx. 680 mm - feed belt length: approx. 3.400 mm - clamping area: 680 x 1.400 mm Djdpfeiim Rnox Am Roch - control panel Machine dimensions: - Length: approx. 3,400 mm - width: approx. 1.700 mm - height: approx. 1.400 mm - Weight: approx. 800 kg

Condition: excellent (used), Year of construction: 1994, Device description: grinding top/bottom working width 200mm Dsdpfx Aowyb Ntom Rech electric adjustment of the upper unit star/delta start-up installed power 14kW pneumatic belt tensioning belt oscillation working height up to 150mm

Condition: used, Working width 3450 mm Working height 2000 mm Number of cylinders 5 St. loading dimensions L x W x H 3600 x 1200 x 2720 mm Hess "Multipress" Perforated Plate Press For all sloped, segmental, and round-arch windows and doors. Also for interior work or frame construction. For gluing staircase block joints and much more. Largest working area approx. 3450 x 2000 mm External dimensions approx. 3600 x 1200 x 2720 mm The vertical perforated plate press is constructed of heavy-duty, torsion-free steel. Thanks to its simple, robust, and economical design, it has a long service life. The perforated plate is made of 10 mm sheet steel with a 50 mm hole pattern. The pressure cylinders and abutments are self-locking. Dcsdpfewqr R Aox Am Reh 5 plug-in hand hydraulic cylinders on a perforated plate with a built-in pump, 2000 kp pressure relief valve, 140 mm pressure plate width, 80 mm pressure plate depth, 60 mm cylinder stroke 4 fixed individual abutments (Technical specifications according to the manufacturer - no guarantee!)

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) Dcjdpfev D Rg Dex Am Reh with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction nozzle: 1930 mm Working...

Condition: used, Number of boring motors 1 St. boring of corner bearing 1=yes, 0=no 1 ja_yes boring of olive 1=yes, 0=no 1 ja_yes 1 HESS fitting drilling station for corner bearings and olives This Hess drilling station for tradesmen offers a lot of drilling technology for little money. A complete station for drilling corner bearings and olives with all the important features, such as 2 clamping cylinders, drilling depth sensing, effective suction, stop systems for corner bearing and olive drilling, drilling head with interchangeable chuck, adjustable drilling feed speed, automatic program sequence. This means technology for perfect work: just one machine with just one drilling unit and just one drilling head for 2 work steps. The system: - Base frame as a support wall for frames and sashes up to 100 mm - Drilling unit positioned in the middle, height manually adjustable via threaded spindle - Drill hole position and depth set to the specified fitting type, can be adjusted via a stop system when changing types - Drilling feed speed can be variably regulated via throttle valve - Direct extraction - Electro-pneumatic control system with automatic Program sequence for - Fixing workpieces - Drill motor on - Drilling unit forwards - Drilling - Drilling unit backwards - Drill motor off - Releasing workpiece fixation - Fixed stop systems Basic equipment / Technical data: Sturdy base frame as a support wall, precise support made of abrasion-resistant and dimensionally stable plastic, for frames and sashes up to 100 mm thick, Corner bearing and olive drilling in one machine and in one drilling unit, simple and convenient, vertical work, easy handling, no templates, minimal time required for the safe workpiece positioning, guarantee for exact and precise drilling, 2 clamping cylinders for immovable fixation of sash or frame, adjustable to different wood thicknesses, side stop in the rebate for the corner bearings, ergonomically arranged stop system for olive drilling with 14 swiveling stops and additional color markings, fixed stop system for drill hole height determination when changing from corner bearing to olive, automatic drilling depth sensing for corner bearing and olive, Djdpfx Amovu Hgzo Rsch drill unit with quick-change chuck for the various tools for corner bearing and olive, tool change in "no time", automatic program sequence, clean work thanks to effective suction, small space requirement and mobile thanks to steering/brake rollers. Electrical equipment in accordance with VDE. Electrical connection: 0.55 KW, 400 V, 50 Hz. Pneumatic connection: R 3/8", 4 - 8 bar Extraction connection nozzle: 1 x 100 mm diameter Extraction speed: 25 m/sec. Space required: Width: 2600 mm Height: 1250 mm Depth: 800 mm Support height: 300 mm Paint finish: RAL 7030 stone grey with RAL 1018 zinc yellow 1 drill set with 1 drill 25 mm and 2 drills 10 mm plus 1 drill 34 mm diameter (technical data according to manufacturer - no guarantee!)

Condition: used, Working width 3500 mm Working height 2550 mm Number of cylinders 6 St. loading dimensions L x W x H 4500x950x2900 mm Hess Speedy frame press ----- will be checked Insertion dimension / pressing length max. 3,500 mm Insertion dimension / pressing height max. 2,550 mm Sliding carriage for width adjustment locking in 50 mm Double hole grid system Electric height adjustment of the long-stroke cylinders (hydraulic) Insertion height of the abutment plates can be preselected in 4 positions 3 vertical printing cylinders stroke 1000 mm Pressure force per cylinder 2000 kN / 20000 N 3 horizontal printing cylinders stroke 80 mm Pressure force per cylinder 1250 kN / 12500 N Printing plate depth 100 mm width 140 mm Grid for cylinder fixation/rear bearing 50 mm Medium pressure beam with shut-off valve Final pressure switch-off and pressure control Control and pressing process in touch button operation Dcjdpjxnqw Tsfx Am Reh Adjustable pressing pressure min. 25 – max. 160 bar Electrical connection 2.2 kW / 400V 3 pendulum pressure plates for studio windows 1 pendulum pressure plate for pointed windows 1 extension for pendulum pressure plate 1 small parts allowance Image and video not original, show identical model ----- (technical data according to the manufacturer - no guarantee!)

Condition: like new (used), functionality: fully functional, total width: 2,600 mm, total height: 1,250 mm, Motor power: 0.75 kW with a drill head for drilling corner bearings and olives Dcodox Ez Uaepfx Am Reh automatic height sensing