Used Faymonville Multimax Satteltieflader (2+2) - Nachlaufgelenkt for sale (78,079)

Condition: new, overall weight: 49,500 kg, axle configuration: 3 axles, Year of construction: 2026, 3-Axle MULTIMAX "PLUS" semi-trailer, air-suspended and with hydraulically forced steering axles. Technical data MultiPLUS-Z-3L-UB-12AT-9.60-17.5-2.54-GR Speed: 80 km/h (legal) Total weight: 49500 kg / 31500 kg Fifth wheel load: 18000 kg Axle load: 31500 kg / 31500 kg Gooseneck length approx.: 3,900 mm Gooseneck width approx.: 2,480 mm Kingpin offset to rear approx.: 2,100 mm Fifth wheel height loaded approx.: 1205 mm Platform length approx.: 9,600 mm Extendable by approx.: ? Platform width approx.: 2,540 mm Loading height at max. load approx.: 890 mm Suspension travel approx.: -55 / +145 mm Axle spacing: 1,360 mm Total weight dependent on fifth wheel load: Yes Special permit required if exceeding country-specific regulations. Technical description Gooseneck: Gooseneck in SNT design to optimize platform length, length approx. 3,900 mm, rear with a bevel of approx. 1,000 mm x 6°. Technical fifth wheel load: 18,000 kg. For tractor-trailer combinations: 4 x 2 and 6 x 2. Platform: Platform, length approx. 9,600 mm with a bevel at the rear of approx. 900 mm x 6°. Platform behind the gooseneck can be hydraulically raised and lowered, length approx. 3,000 mm, loadable up to approx. 9,000 kg. Ramps: DR-10-900-4920-GR-HV-AXS A pair of two-piece AXS steel ramps with a length of approx. 4,920 mm and a width of approx. 900 mm. Open grating deck. Hydraulically folding ramp ends. Ramps can be individually hydraulically shifted outwards by approx. 235 mm and inwards by approx. 365 mm. Maximum load and angle of inclination according to technical data sheet: C470319 Maximum inclination angle with lowered platform: 9° Axles and suspension: BPW axles and suspension, all axles hydro-mechanically forced steered. Technical axle load: 12,000 kg Air suspension with lifting and lowering valve. Axle tool. Tires: 235/75 R 17.5 3PMSF, twin tires. Manufacturer according to our choice Load index 143/141J (144/144F) Braking system: Braking system of the brand WABCO EBS-E according to EU regulations. Without connection cable to the tractor unit. Lighting system: 24-volt lighting system in "ASPÖCK-NORDIK full LED" design according to EU regulations. (ASS 3) Metallization: Complete HRM metallization (High Resistance Metallization) Complete steel structure shot-blasted, then hot-dip galvanized with ZINACOR 850 (Zinc 85% - Aluminum 15%). Painting: 6-coat finish: Complete steel structure shot-blasted after welding. Gkedpfjizu Ntjx Aivjc 1 coat of zinc-based primer, 1 coat of adhesion primer. Top coat with 2 coats of 2-component paint (acrylic), solid color in RAL colors of your choice, followed by sealing of the cavities with special wax. Rims in silver. Multi-color and special paint finishes available at an extra cost. Steel structure: Steel structure made of high-strength fine-grain steels. Steel qualities: S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Welders tested according to DIN-EN 287-1. Welding process MAG according to EN ISO 4063. Protective gas M21 according to EN ISO 14175 Front wall made of steel, plug-in, approx. 400 mm high Connection strip for supply lines to the tractor unit, mounted at the height of the outer frame profile. ASPÖCK-UNIBOX on the connection strip at the front with sockets 24N, 24S & 15-pole. 24N connection according to ISO-1185 24S connection according to ISO-3731 15-pole connection according to ISO-12098 If your pin assignment differs from the ISO connection standard, please inform us. "Anderson" socket on the connection strip at

Condition: new, total length: 19,000 mm, total width: 600 mm, total height: 450 mm, Year of construction: 2022, Color: Red Load capacity: 430,000 kg Expandable Manufacturer: Faymonville Type: G-Module Vessel Deck Year: 2022 Connectable to Goldhofer THP SL Coupling Heads G-Module-SL lowbed coupling head Hydraulically extendable Basic width: 3,000 mm Gsdpfouu Hixsx Aivekc Hydraulically widenable to 4,700 mm Beam height: 450 mm Coupling length: 1,200 mm Weight: 4,500 kg 4 pairs of lashing rings (LC 16,000 daN) 2 alignment pins Control panel for hydraulic adjustments Color: RAL 3002 Telescopic Beams 1 pair of telescopic beams Length: 8,000 mm + 5,000 mm Total length: 13,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 9,600 kg Lashing rings every 1,000 mm LC 10,000 daN 430 MTO Compression joint at the front and rear Color: RAL 3002 Elongation Beams 1 pair of elongation beams Coupling length: 6,000 mm Construction height: 450 mm Beam width: 450/600 mm Weight: 4,300 kg Lashing rings every 1,000 mm LC 10,000 daN 560 MTO Compression joint at the front and rear Color: RAL 3002 Coupling Pin 1 hydraulic coupling pin for G-Module 1 set of connecting lines for coupling pin G-Module = Further Information = Year of manufacture: 2022 Unladen weight: 18,500 kg General condition: very good Technical condition: very good Optical condition: very good Price: On request

Condition: used, axle configuration: > 3 axles, first registration: 10/2006, total width: 2,850 mm, suspension: other, tire size: 285/70R19.5, color: black, Year of construction: 2006, Equipment: ABS, = Additional Options and Accessories = - Central lubrication system = Notes = Faymonville Jeep dolly D3 Year 2006. 1 x lift axle. 1 x friction steering axle / trailing arm steering. Air suspension. Gedpfsxbng Eox Aivokc Max. technical weight: 56,000 kg. Faymonville STBZ-5VA Year 2006. Swivel axle. Removable gooseneck. Movable table. Extendable bed: 400 cm. Loading bed: 650 + 400 cm. 50,000 kg gooseneck capacity. Max. technical weight: 119,680 kg. = Further Information = Axle configuration Tire size: 285/70R19.5 Brakes: Drum brakes Front axle 1: Twin tires; tire tread depth left inside: 15%; tire tread depth left outside: 60%; tire tread depth right inside: 60%; tire tread depth right outside: 60%; suspension: air suspension Front axle 2: Twin tires; tire tread depth left inside: 30%; tire tread depth left outside: 30%; tire tread depth right inside: 40%; tire tread depth right outside: 60%; suspension: air suspension Front axle 3: Twin tires; steerable; tire tread depth left inside: 30%; tire tread depth left outside: 70%; tire tread depth right inside: 60%; tire tread depth right outside: 70%; suspension: air suspension Rear axle 1: Twin tires; steerable; tire tread depth left inside: 30%; tire tread depth left outside: 60%; tire tread depth right inside: 40%; tire tread depth right outside: 70%; suspension: hydraulic suspension Rear axle 2: Twin tires; steerable; tire tread depth left inside: 50%; tire tread depth left outside: 50%; tire tread depth right inside: 30%; tire tread depth right outside: 75%; suspension: hydraulic suspension Rear axle 3: Twin tires; steerable; tire tread depth left inside: 60%; tire tread depth left outside: 60%; tire tread depth right inside: 60%; tire tread depth right outside: 60%; suspension: hydraulic suspension Rear axle 4: Twin tires; steerable; tire tread depth left inside: 60%; tire tread depth left outside: 60%; tire tread depth right inside: 40%; tire tread depth right outside: 50%; suspension: hydraulic suspension Rear axle 5: Twin tires; steerable; tire tread depth left inside: 70%; tire tread depth left outside: 70%; tire tread depth right inside: 20%; tire tread depth right outside: 70%; suspension: hydraulic suspension Weights Unladen weight: 36,600 kg Payload: 99,400 kg GVW: 136,000 kg Financial information Price: On request Identification Type number: STBZ-5VA + 3 AXLE JEEP DOLLY / E = Company Information = ALL PRICES ARE NET FOR EXPORT (Joris Versteijnen NL-DE-GB; Wouter Greutink NL-DE-GB-ES-IT; Govorim po ryccki). We make every effort to provide accurate information. However, no rights can be derived from the information provided.

Condition: new, Unladen weight: 13,170 kg Payload: 33,830 kg Gross vehicle weight (GVW): 47,000 kg General condition: very good Technical condition: very good Gsdpfxoz Hlryj Aivekc Optical condition: very good EU representative: Gomez Trading Holland B.V., Spitsstraat 29C, 91205 Raalte, NL

Condition: new, maximum load weight: 30,190 kg, overall weight: 43,000 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Extract from the equipment list. Full equipment details available on request. Loading Platform: - Lowbed with external beams in extendable SUPER LOW design, length approx. 6,850 mm - Lowbed with fixed hardwood floor approx. 40 mm thick and mechanical locking mechanism - Supply lines protected inside the extendable side rails, automatically adjusting to the current bed length - 5 pairs of lashing rings, foldable outward (LC 10,000 daN) - 6 pairs of threaded blocks on the inner beam for attaching RUD screw-on rings Gooseneck: - Gooseneck in SNT design for optimized platform length, length approx. 3,750 mm - Gooseneck hydraulically liftable/lowerable and detachable - Technical fifth wheel load: 23,000 kg - For tractors: 4x2, 6x2 Rear Chassis: - Rear chassis in short version with closed external frame and checker plate cover - Running gear with excavator recess, closed in the rear half to accommodate the air tanks - 2 pairs of lashing rings, foldable outward (LC 5,000 daN) - 1 pair of lashing rings, foldable outward (LC 10,000 daN) - 1 pair of lashing rings horizontal, front & rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Technical axle load per axle: 12,000 kg - Air suspension with lift and lower valve Tyres: - Tyres 245/70 R 17.5 3PMSF - Manufacturer of our choice - Load index (146/146F) - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transmission to the truck via the standardized EBS interface in accordance with ISO 11992 - The truck must be capable of processing and displaying this data for correct operation Braking System: - Braking system according to EU regulations with EBS-E (2S2M) Electrical System: - Electrical system according to EU regulations, lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with indicators Godpfx Asxarl Neivokc - ASPÖCK-UNIBOX at the front connection point with 24N, 24S, and 15-pin sockets as per standards: - 24N ISO-1185 - 24S ISO-3731 - 15-pin ISO-12098 Steel Construction: - Steel construction from high-strength fine-grained steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa) S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure is automatically shot-blasted after welding using a blasting turbine system - Second blasting process with corundum for optimal adhesion of coating system - HRM metallization of complete chassis with ZINACOR 850 (85% zinc / 15% aluminum) to ensure maximum corrosion protection - Final paint finish with 2 coats of 2K topcoat, single color in RAL 3002 Carmine Red, as per RAL system 841GL - Rims in silver - Rear section metallized and painted RAL 9010 (Pure White) - Metallic paint not possible - Paint system tested in salt spray test as per ISO 9227-NSS - Cavities sealed with special wax Including the following additional equipment: - 2" King pin - One galvanized steel front wall, approx. 400 mm high - Remote steering of front and rear axles by cable remote control with pushbuttons, including single track axle monitoring (without installation in the tractor unit) - Hydraulic connections from gooseneck to lowbed with multi-coupling instead of screw couplings - Electro-hydraulic power pack - Preparation for mounting container locks for 1x 20' or 1x 40' container on the external beams - Without container locks

Condition: new, maximum load weight: 42,900 kg, overall weight: 55,000 kg, axle configuration: 3 axles, loading space length: 29,000 mm, total width: 2,540 mm, Equipment: ABS, You will find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from the equipment list. Full specification available on request. LOADING PLATFORM: * Gooseneck, length approx. 3,900 mm with central beam * Loading platform with double-extension, length approx. 9,300 mm * A support table approx. 200 mm wide is permanently welded to the central beam * Pneumatic locking with conical locking pin and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective loading platform length (except for the supply to the first and second lock) * Technical fifth wheel load: 25,000 kg for tractor units: 4x2, 6x2 and 6x4 * TPMS tire pressure monitoring system according to ECE R 141 * BPW axles and suspension, all axles forced steered hydro-mechanically, mounted on turntables * Technical axle load: 12,000 kg each. Air suspension with lifting and lowering valve * 275/70 R 22.5 3PMSF twin tyres. Brand of our choice * ASPÖCK-UNIBOX at the front connection bar with 24N, 24S & 15-pin sockets * 3 kW electro-hydraulic unit for hydraulic operations * 3 pairs of recessed lashing rings in the outer frame of the gooseneck, foldable outward * At the king pin 1 pair of lashing rings (LC 10,000 daN) – all other lashing rings (LC 5,000 daN) * 3 pairs of stake pockets integrated in the outer frame of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 1 crosswise stake pocket bar mounted in the floor of the gooseneck, for plug-in stakes approx. 100 x 50 mm * 1 at the rear of the gooseneck Gkjdpfx Ajyvnd Njivec * 2" king pin * Mechanical landing gear with 2-speed gearbox and crank * 8 pairs of stake pockets integrated in the outer frame of the loading platform, for plug-in stakes approx. 100 x 50 mm * 10 pairs of recessed lashing rings lying in the outer frame of the loading platform, foldable outward * Rear and front steering operable via cable remote control, with single-track axle control, no installation in the tractor unit required * Last axle with air suspension venting activated when the parking brake is applied * Steel front wall, approx. 1,600 mm high, certified according to EN 12642: 2016 XL * Round NATO socket at the front connection bar (Maeler & Kaege VG 96 917) * 1 LED work light each left and right at the landing gear, wired to the tractor unit connection * Wooden floor approx. 32 mm thick on the gooseneck and loading platform * At the extension tube with large cross-section, one locking position every approx. 500 mm * At the extension tube with small cross-section, one locking position every approx. 1,000 mm, allowing for locking every approx. 500 mm * Cut-outs in the outer frame of the loading platform for hooking lashing straps (LC 2,500 daN) * 4 crosswise stake pocket bars mounted in the loading platform floor, for plug-in stakes approx. 100 x 50 mm * 4 wheel chocks with holder under the loading platform * 1 lockable INOX toolbox, approx. 2,390 x 800 x 500 mm (L x W x H), mounted under the loading platform on the left in direction of travel * 1 additional lockable INOX toolbox, approx. 1,250 x 500 x 550 mm (L x W x H), mounted under the loading platform on the right in direction of travel * 1 LED work light each left and right in front of the axles, with wiring * 2 axle load gauges mounted on the left side including axle load diagram * 1st axle with automatic lift axle function as well as starting...

Condition: new, maximum load weight: 25,645 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete stock of immediately and soon-to-be available vehicles on our website. Excerpt from equipment specification. Complete specification available on request. Load area: - Low-bed design with central beam, extendable version, approx. 6,750 mm in length - 5 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the loading platform (LC 10,000 daN) Gooseneck: - Hydraulic lifting/lowering gooseneck, detachable Rear chassis: - Short rear chassis with closed outer frame and checker plate covering - Chassis with excavator trough, closed in the rear half for housing the air tanks - 2 pairs of fold-out external lashing rings (LC 5,000 daN) - 1 pair of fold-out external lashing rings (LC 10,000 daN) - 1 pair of flat-mounted lashing rings at the rear of the chassis (LC 10,000 daN) Axles: - BPW axles, hydro-mechanically forced steering - Air suspension with raise/lower control valve Tyres: - Tyres 245/70 R 17.5, 3PMSF - TPMS: Tyre Pressure Monitoring System according to ECE R 141 Brake system: - Wabco braking system in accordance with EU regulations with EBS-E (2S2M) Paintwork: - High-quality single-tone 2-component (2K) top coat in RAL 3000 Flame Red Gkedpfx Aoxf Sileivjc Including the following additional equipment: - 2 kingpins - Galvanised steel front wall, approx. 400 mm high - Remote steering from front and rear, operated by cable remote control with push buttons, including single tracking control for the axles (no installation in the tractor unit) - Electro-hydraulic unit - Axle load gauge including load diagram - On the gooseneck, removable aluminium side walls and rear wall, approx. 2,440 x 400 mm (L x H). Rear galvanised stake pockets are removable. (Body length approx. 2,560 mm) - Separate air connection with air gun on the gooseneck - 2 work lights with switch on the trailer, mounted on the left and right of the gooseneck platform - 1 INOX toolbox, approx. 1,350 x 400 x 400 mm, on the gooseneck - 6 pairs of stake pockets for insertable posts approx. 100 x 50 mm in the outer frame of the load area, 2 pairs in the chassis outer frame - Galvanised, extendable width extensions approx. 230 mm per side - Hydraulic connections from gooseneck to low bed with multi-coupling (instead of screw couplings). No seal guarantee included. - Central lubrication system with 2 BEKAMAX (Pico) pumps, standard NLGI-2 grease, with removable protection around the pump - 2 pairs of WADER container locks on the loading area, for 1x20' container - 1 removable galvanised intermediate table with 1 pair of WADER container locks - 1 pair of steel ramps for bridging the low bed’s hook mountings - Anti-slip sand-coated layer painted on the load area - HRM Metallisation (High Resistance Metallisation)

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 2950x1620x1770 mm Weight 3300 kg Gksdpfevz Hxkox Aivsc Total power requirement 71,5 kw

Condition: new, maximum load weight: 25,300 kg, overall weight: 38,000 kg, axle configuration: 2 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately or at short notice, on our website. Excerpt from the equipment details. Full specifications available upon request. Neck (Gooseneck) * Gooseneck in SNT design to optimize loading platform length * Approx. 3,750 mm long, hydraulically liftable/lowerable and detachable * Technical fifth wheel load: 25,000 kg For tractors: 4x2 and 6x2 Kessel Bridge (Tiefbett section) * Low bed designed as extendable Kessel bridge in SUPER LOW design * Approx. 6,850 mm length * With mechanical locking * Service lines routed protected inside the extendable beams, automatically adjusting to match the low bed’s length Gkodpfx Aev Sw E Asivec Rear Chassis * Short version with closed outer frame and checker plate cover * Chassis with excavator trough, closed at the rear half to accommodate air tanks Axles * BPW axles and suspension, all axles hydro-mechanically forced steered * Technical axle load: 12,000 kg per axle * Air suspension with lifting and lowering valve Tires * GOODYEAR KMAX T 3PMSF (M+S) 245/70 R 17.5 twin tires. Load index 143/141J (146/146F) Brake system * Brand: WABCO, EBS-E according to EU regulations, without connection cable to the tractor unit Paintwork * 6-Coat final treatment * All-steel construction shot-blasted after welding * 1 layer of zinc-based primer * 1 layer of adhesion primer. Final coating with 2 coats of 2-component acrylic paint in a single color, followed by cavity sealing with special wax Trailer color * RAL 3002 Carmine Red * Rim color: Silver grey * Drop side color: Natural aluminum Accessories included * Removable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic unit for hydraulic operations (except for hydraulic winches). Without supply connection installed on tractor unit * Spare wheel carrier in front of the gooseneck front wall * Side beams of the gooseneck with fixing holes for bolted lashing rings; first hole approx. 200 mm from the front, then at approx. every 400 mm * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 lashing ring each left and right on the rear taper of the gooseneck (LC 6,000 daN) * 2" king pin * Hydraulic cross member for supporting the gooseneck on the tractor unit or a dolly * Air connection with air gun at the gooseneck * 1 pair of steel ramps with climbing strips and securing pins to bridge the mountings of the low bed * 1 lashing ring each left and right on the front cross member (LC 10,000 daN) * Outer side beams of the loading area prepared for removable loading floor * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the inside carrier’s exterior of the loading area * Lashing rings with retaining spring at approx. every 1,200–1,300 mm on the outer carrier’s exterior of the loading area (LC 10,000 daN) * Cut-outs above the lashing rings in the outer carrier’s upper flange * Mechanical pin-tab coupling from low bed to rear chassis, for swapping the loading floor or installing extension beams, with electro-pneumatic-hydraulic couplings * The outer carriers of the low bed coated with anti-slip sand finish for slip resistance * 2nd ride height for high ride position, max. ± 50 mm from normal ride position, without installation of controls from the tractor unit * 1 pair lashing rings with retaining spring at the transition from the low bed to the excavator trough (LC 10,000 daN) * Front and rear tapers

Condition: new, axle configuration: 3 axles, permissible axle load (axle 1): 10,000 kg, permissible axle load (axle 2): 10,000 kg, permissible axle load (axle 3): 10,000 kg, loading space length: 29,000 mm, loading space width: 2,540 mm, loading space height: 2,850 mm, total length: 29,000 mm, total width: 2,540 mm, total height: 2,850 mm, suspension: air, tire size: 385/65-R22.5, Year of construction: 2026, Equipment: ABS, - BPW axles - EBS - Air suspension - Disc brakes - Central lubrication system NEW MAX210-Z-3AA-13.60-22.5-2.54, available directly from stock Technical data MAX210-Z-3AA-13.60-22.5-2.54 Total weight: 48,000 kg / Coupling pressure: 18,000 kg / Axle load: 30,000 kg / Tare weight: 11,456 kg / Payload approx.: 36,544 kg / Coupling height (laden): 1150–1250 mm / Turning radius: 2300 mm Loading area length: 13,600 mm / 2-way extendable (2 x 770 mm) to 2900 mm / Wheelbase: 1810 mm Technical description: Extendable loading area with pneumatic locking / A fixed intermediate table of ± 250 mm is located in the central box structure. / 8 pairs of lashing eyes that fold outwards (LC 5,000 daN) / 3 pairs of lashing eyes that fold outwards (LC 10,000 daN) / Recesses in the outer frame for attaching lashing straps (LC 2,000 daN) Tires: Tires 385/65 R22.5 (Brand: Goodyear) Tire pressure monitoring system (TPMS): TPMS according to ECE R 141 Axles: Gsdpfx Aiozhxgijvekc BPW axles with disc brakes, air-suspended with raising and lowering valve. All axles are hydromechanically steered. Technical axle load: 10,000 kg (ET 0) Braking system: WABCO braking system according to EU regulations with EBS-E system (2S2M), without connecting cable to the tractor. Steel structure: Steel structure made of high-quality fine-grain steel. Steel grades: S355J2+N/S355MC (Yield strength 355 MPa) / S690QL/S700MC (Yield strength 690 MPa) Electrical system: Electrical system according to EU regulations, lighting 24 V ASPÖCK-NORDIK (ASS3). ASPÖCK-UNIBOX on the galvanized connection strip at the front with 24N, 24S and 15-pin sockets. Connections according to ISO / 24N ISO-1185 / 24S ISO-3731 / 15-pin ISO-12098 Warning signs: Below the gooseneck and at the rear, left and right, holder for warning signs with socket. Options: • Maneuverability at the front and rear via cable remote control with PDC light control for axle alignment. (without mounting on the tractor) • Electro-hydraulic unit (approx. 45 kg) • 2 wheel chocks with holder on the partition wall • Kingpin 2" • Galvanized steel partition, approx. 1600 mm high. EN12642-XL • White reflector tape according to EU regulations over the entire length and width. Red at the rear. • EU marking plates (red-yellow) at the rear of the vehicle. • Holder for a rotating beacon at the rear of the vehicle. • Loading floor made of 30 mm thick hardwood, reinforced with omega profiles (approx. 298 kg). • 10 pairs of stake holder, approx. 100 x 50 mm, in the outer frame of the loading floor. • 1 spare wheel holder under the loading floor on the right. • BEKAMAX (Pico) central lubrication system with 2 pumps. • 6 pairs of recesses in the loading floor for WADER container locks, for 1 x 20', 2 x 20', 1 x 40' or 1 x 45' container. • 5 pairs of stake profiles, mounted across in the loading floor, for stakes 100 x 50 mm • Galvanized storage compartment under the loading floor (2390 x 720 x 400 mm) • Rope hooks (8 mm), every approx. 500 mm below the edge profile of the gooseneck and the loading floor • Ladder, mounted on the left in the direction of travel • Stainless steel toolbox • LED lighting • 10 pairs of twist locks (100 x 50 mm, length 1000 mm) • 8 container General information Year of manufacture: 2026...

Condition: new, Year of construction: 2025, Dimensions (L/W/H) 3550x1450x1800 mm Weight 3500 kg Total power requirement 94,75 kw Gkodpfx Asvz Hxqoivec

Condition: used, maximum load weight: 31,100 kg, overall weight: 42,000 kg, axle configuration: 3 axles, first registration: 03/2013, Year of construction: 2013, Equipment: ABS, * Faymonville F-S43-1ABA low-loader * First registered: 03-2013 * Hydraulic lift * Hydraulically adjustable double-folding gooseneck * Includes cable winch with remote control * 3rd axle with trailing linkage * SAF axles * Air suspension * Drum brakes * Payload: 10,900 kg * Net weight: 31,100 kg * Gross vehicle weight: 42,000 kg * Tires 235 / 75 R 17.5 * More pictures and videos available via WhatsApp Gjdpfx Aiezq N N Hevskc * Specifications subject to change without notice; sale subject to prior sale.

Condition: used, Year of construction: 2022, operating hours: 3,500 h, functionality: fully functional, machine/vehicle number: GL61180KC, The 3E shredder is currently still in use. It will soon be replaced with a more powerful machine. Shaft length: 1800mm 2 x 90kW motors The sale of this machine includes 1 new gearbox and 2 used gearboxes. Also included are 1 new motor and 2 used motors. For more information, please visit the 3E Machinery website, where we purchased this machine. This shredder has always been used for shredding car tires. Gksdpfxoz Rmt Us Aivoc

Condition: excellent (used), axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, loading space length: 18,000 mm, loading space width: 2,540 mm, loading space height: 1,700 mm, total length: 18,000 mm, total width: 2,540 mm, total height: 1,700 mm, suspension: air, tire size: 435/50-R19.5, Equipment: ABS, - BPW axles - EBS - Lift axle - Air suspension - Disc brakes Available directly from stock: MAX200 with a flat loading ramp, lowered, capable of carrying up to 12,000 kg and vertically positionable, extendable by 4.5 m, equipped with a trailing steering axle and a lift axle: Technical data MAX200-N-3A-13.50-FTR-19.5-2.54 Total weight: 45,000 kg Coupling pressure: 18,000 kg Axle load: 27,000 kg Coupling height (loaded): 950–1050 mm Loading area length: 13,500 mm Extendable by: 4,500 mm Axle distance: 1360/1405 mm Vehicle overall width: 2,540 mm Total weight depends on coupling pressure. Loading area: Loading area in extendable design with pneumatic locking. The loading platform can be lowered hydraulically at the rear by approx. 2100 mm. Load capacity of the rear vehicle in horizontal position: 6 t. Gkjdsz Hci Nspfx Aivjc Lowered: Can be driven with an axle load of 12 t. 2 pairs of lashing points (LC 5000 daN). 1 pair of lashing points (LC 10000 daN). 6 pairs of lashing points that fold outwards (LC 5000 daN). 2 pairs of lashing points that fold outwards (LC 10000 daN). 1 pair of horizontal lashing points at the rear (LC 5000 daN). Recesses in the outer frame of the loading platform for attaching lashing straps (LC 2000 daN). Tire pressure monitoring system (TPMS) according to ECE R 141. BPW axles with disc brakes. Tires 435/50 R 19.5 Options: • Red and yellow air couplings on the galvanized front connection plate. • 2 wheel chocks with holder. • Galvanized steel partition, approx. 1,600 mm high (approx. 35 kg), EN12642-XL • Loading area made of hardwood. • Hardwood floor on the hydraulic loading table. • 1 pair of aluminum ramps, type: VFR 105, 1,500 x 450 x 120 mm (L x W x H). • Holder for aluminum ramps under the ramp (approx. 88 kg). • 1 spare wheel holder under the loading area on the right. • Movable profile for attaching separate aluminum ramps at the rear of the semi-trailer. • Operating manual and description on a USB stick. • Holder for a rotating beacon at the rear, right and left of the vehicle. • Under the gooseneck and at the rear, on the left and right, a holder for warning signs with socket. • Electro-hydraulic unit (approx. 45 kg). • 6 pairs of recesses in the loading area floor for WADER container locks, for 1 x 20', 2 x 20', 1 x 40' or 1 x 45' container (approx. 90 kg). • 10 pairs of tubes for stanchions (approx. 100 x 50 mm) in the outer frame of the loading area floor (approx. 30 kg). • 3 pairs of stanchion profiles, mounted crosswise in the loading area floor, for stanchions (100 x 50 mm) (approx. 95 kg). • Galvanized widening elements, extendable by approx. 230 mm per side (approx. 262 kg). • Lift axle on the front axle, controlled by TEBS E depending on axle load and loading condition (± 69 kg). • 4 warning signs (width ± 423 x 423 mm), extendable by ± 400 mm, each with one LED position light (± 25 kg). • Rope hooks (8 mm), approx. 500 mm below the edge profile of the gooseneck and the loading area floor (± 2 kg). Axle configuration Tire size: 435/50-R19.5 Axle brand: BPW DISC Brakes: Disc brakes Suspension: Air suspension Rear axle 1: Lift axle; Max. axle load: 9000 kg; Tire tread left: 100%; Tire tread right: 100% Rear axle 2: Max. axle load: 9000 kg; Tire tread left: 100%; Tire tread right: 100% Rear axle 3: Max. axle load: 9000 kg; Steered;...

Condition: used, overall weight: 48,000 kg, axle configuration: > 3 axles, first registration: 02/2012, Year of construction: 2012, Equipment: ABS, * Faymonville STN-4UBX low-bed trailer * First registered: 02-2012 * Hydraulic lifting system * Hydraulically adjustable double folding ramps * Including winch with remote control * 3rd and 4th axles with trailing steering * SAF axles * Air suspension * Drum brakes * Payload: 11,900 kg * Tires 235 / 75 R 17.5 * More pictures and videos available via WhatsApp Godszurgvepfx Aivjkc * Information without guarantee and subject to prior sale.

Condition: used, axle configuration: 3 axles, permissible axle load (axle 1): 9,000 kg, permissible axle load (axle 2): 9,000 kg, permissible axle load (axle 3): 9,000 kg, first registration: 08/2012, wheelbase: 9,860 mm, Year of construction: 2012, Rear axle 1: Max. axle load: 9000 kg Rear axle 2: Max. axle load: 9000 kg Rear axle 3: Max. axle load: 9000 kg Empty weight: 12.220 kg Carrying capacity: 35.780 kg GVW: 48.000 kg APK (MOT): tested until 01/2027 Production country: BE Gksdpfxjz I Avre Aivsc Please contact Theo Lelie , , ) for more information

Condition: used, Year of construction: 2007, 2007 | Faymonville STBZ3 | Used Low Bed Semi-trailer 📍Location: Germany 🚛 Delivery available to your destination – Use our shipping calculator to estimate transport costs! 💰 Buy Now for EUR 32500 or Make an Offer. Payment at delivery available for an affordable fee (subject to approval)* 👷‍♂️ Inspected by an independent expert 12 inspection points 12 approved ✅ 0 imperfect ℹ️ 0 issues ⚠️ 📌 Inspector's Comment: Tiltable bed trailer, with some body work to do. Has its own hyd-agregat. Gjdpoznl Tvsfx Aivjkc 📄 Want to see the full inspection, extra photos, or a video? Tip: The reference "40866 Equippo" is commonly used when looking up more details online. 💡 Why this machine and our service stands out: ✔ Thorough inspection by professionals ✔ Jobsite delivery available ✔ Money-Back Guaranteed ✔ Secure and flexible payment options 🔄 Considering other equipment options? We offer helpful tools and resources for all equipment owners and operators – easily accessible on our platform.

Condition: used, axle configuration: > 3 axles, first registration: 12/2011, total length: 13,450 mm, total width: 2,540 mm, suspension: air, tire size: 205/65R17.5, wheelbase: 10,160 mm, color: red, Year of construction: 2011, Equipment: ABS, Coupling height: 96 cm. Loading floor: 955 cm + 430 cm extendable. Loading height: 76 cm. 2 x self-tracking axles / trailing steering. Including a set of aluminum ramps. = Further Information = Axle configuration Tire size: 205/65R17.5 Brakes: Drum brakes Suspension: Air suspension Front axle 1: Dual tires; tire tread depth, left inner: 50%; tire tread depth, left outer: 50%; tire tread depth, right inner: 50%; tire tread depth, right outer: 50% Front axle 2: Dual tires; tire tread depth, left inner: 60%; tire tread depth, left outer: 60%; tire tread depth, right inner: 60%; tire tread depth, right outer: 60% Front axle 3: Dual tires; tire tread depth, left inner: 70%; tire tread depth, left outer: 70%; tire tread depth, right inner: 70%; tire tread depth, right outer: 70% Front axle 4: Dual tires; tire tread depth, left inner: 70%; tire tread depth, left outer: 70%; tire tread depth, right inner: 70%; tire tread depth, right outer: 70% Weights Unladen weight: 9,600 kg Payload: 30,400 kg GVW: 40,000 kg Maintenance APK (Technical Inspection): valid until 01/2027 Identification Model number: STN-4AX STN-4AX / MEGA / EXTENDA = Company Information = Gedjz H Tnijpfx Aivokc ALL PRICES ARE NET FOR EXPORT. (Joris Versteijnen NL-DE-GB, Wouter Greutink NL-DE-GB-ES-IT. Govorim po ryccki). We make every effort to provide accurate information. However, no rights can be derived from the information provided.

Condition: good (used), Year of construction: 2003, functionality: fully functional, HAAS VF 2 VERTICTAL MACHINING CENTRE TABLE 914 X 356 MM TRAVERSES - 762 X 406 X 508 MM MAX CUTTING RATE 16.5 M/MIN SPINDLE MOTOR 20 HP Gjdpfx Aioz Ehxysvjkc 20 ATC 40 TAPER SPINDLE SWARF CONVEYOR STANDARD COOLANT OVERALL DIMESIONS - 2790 X 2350 X 2650 MM WEIGHT 3.5 TON ORIGINAL PAINTWORK , VERY VERY GOOD FOR ITS AGE .

Condition: new, maximum load weight: 34,104 kg, overall weight: 47,000 kg, axle configuration: 2 axles, Year of construction: 2026, Further information here: Gkjdpfx Aijv D Abgjvec

Condition: used, Year of construction: 2022, Hardwood Azobe boards, sourced from our own semi-trailer low-loader. Trailer is from 2022 Dimensions; - 6 pieces - 275 x 19.5 x 4.5 cm. Gkodsz Hmqqjpfx Aivsc - 8 pieces - 262 x 19 x 4.5 cm. - 6 pieces - 95 x 19.5 x 4.5 cm. - 8 pieces - 91.5 x 21.5 x 4.5 cm. - 8 pieces - 43 x 21.5 x 4.5 cm. - 10 pieces - 68.5 x 17.5 x 3 cm.

Condition: used, Year of construction: 2007, functionality: fully functional, Tetra Pak Pressvatic 1+2 – Pre-Press & Block Format System Manufacturer: Tetra Pak Model: Pressvatic 1+2 Machine Type: Cheese Pre-Press & Block Formatting System Application: Industrial Cheese Production Capacity: Approx. 1.8 tonnes/hour Condition: Used Location: Ireland Gkodozy Rxhopfx Aivoc Description: Tetra Pak Pressvatic 1+2 pre-press and block-format system designed for integration into high-volume industrial cheese production lines. The Pressvatic performs the preparation and pre-pressing of cheese curd prior to forming and cutting the cheese into production blocks. It is designed to provide controlled curd distribution, whey drainage, pre-pressing and block formatting as part of an automated cheese manufacturing process. The system is particularly suited to production of granular and round-eyed cheeses and can be integrated with upstream cheese vats and curd-handling equipment and downstream main presses. Key Features: - Tetra Pak Pressvatic 1+2 system - Automatic pre-pressing and block formatting - Approx. 1.8 tonnes/hour capacity - Designed for industrial cheese production - Automated curd distribution - Whey drainage system - Pneumatic pre-pressing - Cheese block forming and cutting - Stainless-steel food-processing construction - Designed for integration into automated cheese production lines - CIP-compatible hygienic design - Suitable for continuous industrial cheese manufacturing operations - Cheese Applications Suitable for production of a range of cheeses including: Gouda Edam Havarti Swiss-type cheeses Other granular and round-eyed cheeses Tetra Pak Pressvatic, Tetra Pak Pressvatic 1+2, Pressvatic 1+2, Tetra Pak cheese equipment, Tetra Pak cheese press, cheese pre press, cheese pre-press, cheese block former, cheese block formatting machine, cheese block forming machine, cheese production equipment, cheese pressing equipment, dairy processing equipment, cheese manufacturing equipment, industrial cheese equipment, used cheese machinery, used dairy equipment, Tetra Pak dairy equipment, 1.8 tonne cheese press, cheese production line, Gouda cheese equipment, Edam cheese equipment, Havarti cheese equipment, Ireland, Europe

Condition: good (used), total length: 13,350 mm, total width: 2,550 mm, total height: 3,700 mm, Year of construction: 2012, Carrying capacity: 27.300 kg Gkedpfx Aoy H Du Soivsc GVW: 12.700 kg Technical condition: good Visual appearance: good Production country: BE Please contact Christian Theißen for more information Manufacturer: Euromax GTZ-3AUB Model: Multimax STN-4UBX Year of build: 2012 Condition: Used Data: First registration: 02/2012 Total dimensions LxWxH: 13,35 x 2,55 x 3,70 m Empty weight: 12.700 kg Total permissible weight: 40.000 kg Payload: 27.300 kg Number of axles: 3 Special features: Extendable by 3m (16.35m), forced-steering trailing axle, hydraulic lifting bed to gooseneck Location: Essen immediately available

Year of construction: 2006, condition: good (used), For sale are 3 Siemens component placement machines, consisting of: 1 unit X 2 (year of manufacture 2006), model B 348 = €10,900 + VAT 1 unit X 2 (year of manufacture 2006), model B 251 = €10,900 + VAT Both machines have been inspected and tested for full functionality in our workshop. All machines have a valid maintenance report. An on-site inspection is possible and desired. Please refer to the photos for the technical data and configuration of the respective machines. We will also be happy to answer any questions you may have about the machines in person. Upon request, a reference run video is available for each machine. We can also carry out modifications for your specific application for an additional charge. Gkodpfx Aoyrm E Aoivec The machines are sold without component tables or MTC. Location of the machines: Zollner Elektronik AG / Warehouse Roding / Buchenstraße 18 - 20 / 93426 Roding

Condition: used, axle configuration: 3 axles, first registration: 04/2019, loading space length: 9,200 mm, loading space width: 2,540 mm, suspension: air, tire size: 245/70R17.5, color: grey, Year of construction: 2019, Faymonville F-S43-1AAF 660 cm Extendable Hydraulic ramps Winch Forced steering = Further information = Tire size: 245/70R17.5 Suspension: Air suspension Front axle: Dual tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Center axle: Dual tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Rear axle: Dual tires; Steered; Tire tread depth left inner: 50%; Tire tread depth left outer: 50%; Tire tread depth right inner: 50%; Tire tread depth right outer: 50% Unladen weight: 13,500 kg Payload: 47,500 kg Gksdpezinblsfx Aivjc GVWR: 61,000 kg Model number: F-S43-1AAF / EXTENDABLE / HYDRAU = Company information = ALL PRICES ARE NET FOR EXPORT. (Joris Versteijnen NL-DE-GB) (Wouter Greutink NL-DE-GB-ES-IT) (Govorim po ryccki) We make every effort to provide accurate information. However, no rights can be derived from the information provided.