Used 150 T Straightening Press - Horizontal for sale (85,165)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,000 kg, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, volume flow: 795 m³/h, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. Gbsdpozbxwisfx Afkjn • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode, see video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 2019, operating hours: 3,000 h, functionality: fully functional, pressing force: 70 t, overall weight: 9,500 kg, year of last overhaul: 2025, filling opening width: 420 mm, filling opening length: 1,250 mm, Technical data packing press / can press / metal sheet press: Manufacturer unoTech GmbH Type UPAXX 70 Year of manufacture 2019 Operating hours approx. 3,000 hours Pressing force 700 kN at 315 bar Filling opening chute 420 x 1,250 mm (d x w) Channel cross-section (package dimension) 350 x 500 mm (h x w), length depending on material Drive power 30 kW Connected load 40 kW Power consumption, total 70 A Throughput capacity for empty beverage cans with: one pressing stroke approx. 1.7 t/hour two pressing strokes approx. 2.5 t/hour Gbsdpfezbxvljx Afksn Achieved compaction approx. 1200 kg/m³ Hydraulic oil tank capacity 850 l Press dimensions built up 8,000 x 1,600 x 2,500 mm (l x w x h) Transport weight press approx. 9.5 t Accessories: Oil cooler 1.5 kW, oil tank heater 1.5 kW, press box made of wear-resistant steel S355 Material properties: According to the manufacturer, this machine is suitable for pressing tin cans, metal sheet offcuts, sheet steel as well as aliminium, brass and copper waste. Condition of the baler: The packing press has been fully overhauled in our workshop. The press is in very good condition; please see the demonstration video following the overhaul. The machine sustained transport damage whilst being moved. The control cabinet was damaged and slightly dented by a forklift truck, and the main switch (on/off switch) was damaged. These damages are reflected in the significantly reduced sale price and must be repaired by the buyer at their own expense. Comments: The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: good (used), Clamping plate, plate field, welding table, welding table, clamping plate, scribing and measuring plate, measuring table, straightening plate, short-stroke heavy-duty cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic press, bending machine, straightening machine, profile straightening system, strip straightening machine, strip straightening device, shaft straightening system, combined bending machine-straightening press, profile bending machine, bending machine bending/straightening press Gedpfxezbhqxe Afkjbn -Mounting plate: Mounting plate with straightening press -Length: 3260 mm -Width: 1380 mm -Piston diameter: Ø 63 mm -Stroke: 200 mm -Pressure force: t -Overall dimensions: 3260/1380/H1940 mm -Weight: 2820 kg

Condition: good (used), Clamping plate, plate field, welding table, welding table, clamping plate, scribing and measuring plate, measuring table, straightening plate, short-stroke heavy-duty cylinder, hydraulic cylinder, support cylinder, hydraulic ram, pressure ram, hydraulic press, bending machine, straightening machine, profile straightening system, strip straightening machine, strip straightening device, shaft straightening system, combined bending machine-straightening press, profile bending machine, bending machine bending/straightening press -Mounting plate: Mounting plate with straightening press -Length: 4025 mm -Width: 1990 mm -Piston diameter: Ø 63 mm -Stroke: 110 mm -Pressure force: 20 t -Overall dimensions: 1990/4025/H1920 mm Gbjdpezakf Nefx Afken -Weight: 5060 kg

Condition: as good as new (ex-display), Year of construction: 2024, tool height: 130 mm, pressing force: 12 t, bending force (max.): 12 t, Stierli bender 120HE horizontal press Horizontal bending machine, manual control with angle fine adjustment. Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bending pressure 12 tons tool height 130 mm Stroke 0-170 mm stepless Bending capacity 130x12 mm S235 Straightening performance light straightening work Pipe bending 3/8"-11/2" Gbedpeflc R Defx Afkjn Demonstration machine year 2024 incl. hand and foot pedal Machine as good as new

Condition: as good as new (ex-display), Year of construction: 2024, functionality: fully functional, tool height: 200 mm, operating speed: 10 mm/s, working height: 200 mm, bending angle (max.): 180 °, sheet thickness steel (max.): 20 mm, sheet thickness copper (max.): 20 mm, lifting speed: 10 mm/s, bending force (max.): 42 t, Stierli bender 420HE Horizontal bending machine, with manual control and angle fine adjustment system Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bending pressure 42 tons Tool height 200 mm Stroke 0-300 mm stepless Bending capacity 200x24 mm S235 Straightening power for HEA180 Gbodpfx Asflc Spofken Bending and straightening program via selector switch Demonstration machine year 2024 incl. hand and foot pedal Machine as good as new

Condition: as good as new (ex-display), Year of construction: 2024, tool height: 300 mm, stroke length: 350 mm, bending angle (max.): 180 °, pressing force: 82 t, sheet thickness steel (max.): 30 mm, sheet thickness copper (max.): 30 mm, lifting speed: 10 mm/s, bending force (max.): 82 t, Stierli bender 820HE Horizontal bending and straightening machine, with manual control and stroke fine adjustment system STRAIGHTENING with this horizontal press: Fast and precise straightening for welding parts, profiles, beams, sheets, pipes, flat steel, etc.... BENDING with this horizontalpress: Very universal, for bending flat steel, sheet, round steel, profiles, tubes angular or round, forming tools and easy fixing of own tools or special tools, + straightening as straightening press. Bending pressure 82 tons Tool height 300 mm Godpfx Aegqfmnjfksbn Stroke 0-300 mm stepless Bending capacity 300x20mm (up to 300x30 with large V-block) S235 Straightening power for HEA260 Bending and straightening program via selector switch Demonstration machine year 2024 incl. hand and foot pedal Machine as good as new

Condition: new, 60.06 m shelving, 60 cm deep , Workshop shelving , Storage shelving , Manual storage , Push-in shelving , Small parts storage Data : - Height : approx. 200 cm - Depth : approx. 60 cm - Length : approx. 60.06 running meters Gbodpfjzbtxzsx Afkjn Shelf offer 60.06 running meters consisting of: - 0061 x upright approx. 200 x 60 cm, disassembled (incl. 2 x base & 2 x cover cap). - 0300 x shelf approx. 100 x 60 cm. - 1200 x shelf holder. - 0061 x Diagonal 1176 mm ( for crossing ). - 0061 x turnbuckle ( for intersection ). - Manufacturer: META CLIP. - Load: 150 kg per shelf, with evenly distributed load. - Levels: 5 x storage levels. - Surface: sendzimir galvanized. - New from stock. - Made in Germany. - 100% quality at the best price. We can pre-assemble the frames for a small surcharge of 2€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 8000,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : The delivery is carried out on request by our partner forwarding agency, the costs for this depend on the postal code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, 60.06 m shelving, 40 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage , Data : - Height : approx. 200 cm Godpfszbqycox Afkobn - Depth : approx. 40 cm - Length : approx. 60.06 running meters Shelf offer 60.06 running meters consisting of: - 0061 x upright approx. 200 x 40 cm, disassembled (incl. 2 x base & 2 x cover cap). - 0300 x shelf approx. 100 x 40 cm. - 1200 x shelf holder. - 0061 x Diagonal 1176 mm ( for crossing ). - 0061 x turnbuckle ( for intersection ). - Manufacturer: META CLIP. - Load: 150 kg per shelf, with evenly distributed load. - Levels: 5 x storage levels. - Surface: sendzimir galvanized. - New from stock. - Made in Germany. - 100% quality at the best price. We can pre-assemble the frames for a small surcharge of 2€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 5.610,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, 15.06 m shelving, 60 cm deep , Workshop shelving , Storage shelving , Large shelving , Manual storage , Shelving , Small parts storage , Data : - Height : approx. 200 cm - Depth : approx. 60 cm - Length : approx. 15.06 running meters Shelf offer 15.06 running meters consisting of: - 0016 x upright approx. 200 x 60 cm, disassembled (incl. 2 x base & 2 x cover cap). - 0075 x shelf approx. 100 x 60 cm. - 0300 x shelf holder. - 0016 x Diagonal 1176 mm ( for crossing ). - 0016 x turnbuckle ( for intersection ). - Manufacturer: META CLIP. - Load: 150 kg per shelf, with evenly distributed load. - Levels: 5 x storage levels. - Surface: sendzimir galvanized. - New from stock. - Made in Germany. Gedpfx Aszbqxlsfksbn - 100% quality at the best price. We can pre-assemble the frames for a small surcharge of 2€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 2116,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, 30,06 m Shelving, 40 cm deep , Workshop shelving , Storage racks , Large capacity shelving , Manual storage , Shelving , Small parts storage , Data : - Height : approx. 200 cm - Depth : approx. 40 cm - Length : approx. 30.06 running meters Gbjdpfszbqngjx Afken Shelf offer 30.06 running meters consisting of: - 031 x upright approx. 200 x 40 cm, disassembled (incl. 2 x base & 2 x cover cap). - 150 x shelf approx. 100 x 40 cm. - 600 x shelf holder. - 031 x Diagonal 1176 mm ( for crossing ). - 031 x turnbuckle ( for intersection ). - Manufacturer: META CLIP. - Load: 150 kg per shelf, with evenly distributed load. - Levels: 5 x storage levels. - Surface: sendzimir galvanized. - New from stock. - Made in Germany. - 100% quality at the best price. We can pre-assemble the frames for a small surcharge of 2€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 3661,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery is carried out by our partner forwarding company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation.

Condition: new, 15.06 m shelving, 40 cm deep , Workshop shelving , Storage shelving , Manual storage , Push-in shelving , Small parts storage Data : - Height : approx. 200 cm - Depth : approx. 40 cm - Length : approx. 15.06 running meters Godpfx Afszbqnasksbn Shelf offer 15.06 running meters consisting of: - 016 x upright approx. 200 x 40 cm, disassembled (incl. 2 x base & 2 x cover cap). - 075 x shelf approx. 100 x 40 cm. - 300 x shelf holder. - 016 x Diagonal 1176 mm ( for crossing ). - 016 x turnbuckle ( for intersection ). - Manufacturer: META CLIP. - Load: 150 kg per shelf, with evenly distributed load. - Levels: 5 x storage levels. - Surface: sendzimir galvanized. - New from stock. - Made in Germany. - 100% quality at the best price. We can pre-assemble the frames for a small surcharge of 2€/net per piece. -- IMMEDIATELY AVAILABLE SEVERAL TIMES-- Price : 1648,00 € net plus legally valid VAT. You will receive an invoice with VAT shown. Transportation : On request, delivery can be carried out by our partner shipping company, the costs for this depend on the zip code. Assembly : If required, our trained staff will be happy to assist you with the professional assembly and disassembly of your factory equipment. Our recommendation : Let us know what you need... We will be happy to help you with the realization of your projects, from planning and ordering to installation. Are you interested or do you have any questions? Simply contact us by message or phone call. You can find our telephone number on our company page. ☎️ You can reach us by phone from Monday to Friday, 08:00 - 15:00. Alternatively, you can send us a message with your name and number and we will get back to you as soon as possible.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2025, volume flow: 750 m³/h, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with ruffler, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Gbedpoy S Rqwofx Afkjn Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: used, Year of construction: 1979, pressure 100 t stroke 500 mm table surface area 4000x500 mm Gsdpfxsy Tpr Ao Afkobn weight of the machine ca. 5,7 t HY – S 100 RH MAE hydraulic straightening press, complete with straightening unit Year of manufacture: 1979 Approved in accordance with UVV Stroke: 500 mm Pressure capacity: 100 tonnes Table: 4000 x 500 mm Weight: 5700 kg

Condition: used, Year of construction: 1994, Motor 6 / 7.5 kW with 4-roller feed, fixed speeds. Speed extensions. Height of worktable: 920 mm. Spindle tilting: -10° + 45°. Max. spindle projection above table: 175 mm. Spindle speeds: 3250/6500-5000/10000 rpm. Max. tool diameter: 250 mm. Weight: approx. 950 kg. Location: Nattheim. Gbjdpow Enw Iofx Afkjn

Condition: used, Year of construction: 1965, pressure 400 t throat 1140 mm stroke 600 mm table surface area 2000x1000 mm Plate 4000x1000x300 mm ram head dimension 2000x1040 mm Cylinder 300 mm Daylight 650 dimensions of the machine ca. 3,9x4x4,2 m Machine has been overhauled. Maximum distance from ram to clamping plate: 1250 mm The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. Gbedpoyt R Dlofx Afkjn About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: good (used), Code: 0402 Brand: SCM Model: T 150 E - CE Standard Automatic electronic spindle moulder with tilting spindle, complete with feed, for joinery, furniture, custom-made furniture, wooden joinery, doors, timber structures, plastics and composite materials – CE Standard Gbedpfxszb Eqcj Afkon Electronic control for vertical positioning and spindle tilting Inverter: electronic speed variator with display from 1000 to 10000 rpm Reversible rotation Manually adjustable “FAST” sector work table Guide - router hood with easy release mechanism operated by a crank handle Technical data: Work table dimensions 2500 x 800 mm Removable workpiece support Work table height from ground 935 mm Spindle tilting -10° to +45° Spindle diameter 40 mm Max profiling tool diameter 250 mm Max tenoning tool diameter 300 mm Main motor 7,5 Hp Feed roller support device with manual vertical and horizontal movement 3-roller automatic feed MAGGI N° 2 suction inlets diameter 120 mm Overall dimensions mm 2500 x 1350 x 1900 m Weight kg 1000

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,400 mm, filling opening length: 1,100 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 75 kW (101.97 HP), year of last overhaul: 2025, volume flow: 300 m³/h, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport dimensions 8500 x 2450 x 2950 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced Gbedpfoy R Nnfsx Afkon • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see the video for the machine function test. Comments: The documentation (operating instructions, CE declaration, electrical/hydraulic circuit diagram) for the press is available.

Year of construction: 2026, condition: new, functionality: fully functional, • A vertical guillotine shear with a 3 mm or 6 mm steel cutting capacity on a 3 m width, with a motorized back gauge, an optical system for contour cutting, and an optional pneumatic sheet support. • A 50 or 100 T press brake with a 3 m distance between uprights, with 3 digitized axes (X, the back gauge, and synchronization of the left Y1 and right Y2 cylinders). A CYBELEC touch-screen CNC control with digital or graphical programming. Gbedpjzcyx Djfx Afksn Features: With minimal floor space in the workshop, you have the equivalent of 2 high-end conventional machines: • A vertical guillotine shear equipped with a motorized back gauge (700 mm length), an optical system for contour cutting, proportional clamping relative to the cutting force, 2 reversible 4-sided blades, and an optional pneumatic sheet support. • A press brake equipped with a motorized back gauge (700 mm length) and fully electronic angle management with 2 digital rulers (synchronization of the left Y1 and right Y2 cylinders with force management), allowing bending either in a single stroke or in the air with a positioning accuracy of 0.04 mm. - Distance between uprights = 3200 mm - Unlimited bending capability, as there is no interference with the gooseneck! - Direct angle programming + graphical programming with automatic calculation of the developed length and 2D bending simulation. - Automatic pressure control in real time. - A complete set of tooling with a 9-V die + gooseneck punches + adjustable punch holders. - A 2-year warranty. Available in several versions: - Cutting capacities: 3 or 6 mm steel - Cutting lengths: 1250 / 2040 / 3040 mm - Bending pressure: 50 and 100 T - Bending lengths: 1400 / 2200 / 3200 mm - Cybelec graphical CNC control, 3 axes. More than 1000 installations in Europe. Inquire now! With the COMBI and its 3 digitized axes X, Y1, Y2, you really have the equivalent of 2 excellent machines, with the added benefit of technology typically intended for industrial applications (Y1 Y2 synchronization). Since 2004, JC COLOMBO has been distributing the COMBI combined shear and press brake. With ideal capabilities for locksmithing and metalworking activities (3040 x 6 mm shear and 3200 x 75 T bending), the COMBI allows all companies that do not have space for 2 conventional machines to equip themselves and become fully self-sufficient and much more responsive to complete projects. Workshops with 100 m² and 2 employees have opted for the COMBI! A 50 T version has also been specifically designed for the production of cladding for aluminum joinery companies. Furthermore, with equipment such as the automatic sheet support for the shear, the Y1 Y2 cylinder synchronization, and the direct angle setting program, the customer really has the equivalent of 2 excellent industrial-grade machines at a lower cost. To date, more than 600 professionals use the COMBI in France.

Year of construction: 2025, condition: new, Hydraulic C-frame press (punch press) Year of manufacture: 2025 Capacity: 100 tons at 230 bar Control / key switch: 1. Manual setup mode without light sensor 2. Automatic (at full speed) with light sensor Main cylinder: Ø 230 mm Auxiliary cylinders: 2 x Ø 50 x 30 mm Auxiliary guide: 2 x Ø 50 mm Motor: 11 kW – 15 hp Pump: 16 cc – 23 liters / ASC – Helical gear pump Speed: Forward 110 mm/sec – Return 200 mm/sec Pressure phase: 9 mm/sec Installation height: 500 mm Stroke length: 400 mm. Push plate: 750 x 600 mm. – with T-slots Table top: 750 x 600 mm. – with T-slots Table height: 850 mm. (Floor to table top edge) ----- Hydraulic accessories: Hydraulic control block & accessories: REXROTH Pressure adjustment via PLC. (20 – 100 tons) Speed adjustable via PLC. Air cooler Feed valve NG.63 Control accessories: Siemens S7-1200 Blsbjftg Sgsmmvyhwof Main control box Foldable control panel With side safety door (doors can be moved backwards) SICK 750 + 150 mm light sensors. Ruler for adjusting the stroke length 7" PLC screen – Siemens Movable two-hand control Alarm indicator for faults (light & sound) ----- • The press complies with the EN693 Machinery Directive • Hydraulic two-way valves • Dual-channel fused control system • Safety PLC – SICK • Operating instructions & parts list (German) Gbodpfxswag Rio Afkjn • Warranty: 24 months ----- Oil capacity: 190 liters (Tank volume: 205 liters) Total weight: approx. 5,500 kg. Overall dimensions: 1300 x 2000 x 2750 mm. Delivery time: 2 - 3 weeks from stock. Paint finish: Light gray & dark gray The machine is available immediately in 2 - 3 weeks. Freight: approx. €2,000 from Konya to Germany

Condition: used, functionality: fully functional, Hydraulic straightening press Manufacturer: G + K Year of manufacture: 1992 Gbsdpfx Asza S Daefksn Max. pressing force: 130 t Table size (bottom): 800 x 500 mm with T-slots Table size (top): 800 x 500 mm with T-slots Installation dimension: 1000 mm System pressure: 250 bar Electric motor: 15 kW Weight: 3400 kg Operating voltage: 380 AC, 24 DC Bsbmm Av Esxr Rnaeuodc Control system renewed 5 years ago The machine is equipped with 2 tables, one at the bottom and one at the top, each measuring 800 x 500 mm. A throttle valve is installed on the hydraulic unit for pressure adjustment.

Condition: used, functionality: fully functional, Equipment: documentation/manual, Hydraulic straightening press Manufacturer: G + K Year of manufacture: 1992 Max. pressing force 130 t Table size (bottom) 800 x 500 mm with T-slots Table size (top) 800 x 500 mm with T-slots Installation dimension 1000 mm System pressure 250 bar Bjbmm Av Eoxr Rnaeujdc Electric motor 15 kW Weight 3400 kg Gsdoza Szrepfx Afkjbn Operating voltage 380 AC, 24 DC Control system renewed 5 years ago 2 tables (bottom) 800 x 500 mm The hydraulic unit allows for pressure adjustment via a throttle valve, which can be monitored on the pressure gauge. The electrical system was overhauled by Schäger Steuerungsbau.

Condition: new, pressing force: 300 t, For sale is a hydraulic portal straightening press (H-frame) from manufacturer Durendus with a maximum pressing force of 300 t. The machine features a table size of 1,500 × 2,000 mm, a maximum installation height of 1,000 mm, and a stroke of up to 600 mm, making it particularly suitable for straightening, alignment, and heavy forming applications in industrial environments. The machine shown here was built and delivered to a customer’s specification; we can manufacture this machine as a new unit on short notice. Available Options (upon request): The options listed below are based on completed customer projects and allow targeted adaptation of the machine to specific applications. The base machine is delivered in a functional basic configuration—in practice, it is most often expanded with additional features and configured to meet project requirements. Examples include: * Siemens S7-1200 PLC + 7” display for operator interface * Wireless remote control * Safety edge at the base of the portal columns (600 mm) * Table with T-slots * Motorized bridge positioning * Travel path extension * Larger open height * Light curtain under the bridge * Laser distance measurement * Lifting cylinder in the table ##### Technical Data & Information: Hydraulic Portal Straightening Press – H-frame – 300 t ==== General Specification - Designation: Hydraulic portal straightening press - Type: H-frame / portal press - Manufacturer: DURENDUS - Pressing force: 300 t (adjustable) - Distance between uprights: 1,580 mm - Table size: 1,500 × 2,000 mm - Bridge travel: 1,500 mm - Lateral travel (center): ±500 mm - Max installation height: 1,000 mm - Table height from floor: 950 mm - Ram extension: 200–400 mm - Total weight: approx. 9,500 kg ==== Hydraulic Cylinder - Piston stroke: 0–600 mm - Max working pressure: 250 bar - Return speed: 16 mm/s - Ram speed: 10 mm/s ==== Hydraulics & Drive - Hydraulic pump: ASC - Pump capacity: 60 l/min - Tank volume: 250 l - Motor rating: 11 kW - Pressure accuracy: ±5 bar - Hydraulic unit: top-mounted - Valve technology: DUBLOMATIC - Filter: FILTREC - Oil level monitoring: electronic - Cooling: air cooling ==== Movement System - Bridge drive: 2 × 2.2 kW - Lateral cylinder movement: 0.75 kW - Movable bridge: yes - Laterally movable cylinder: yes Gsdpfxjyzfkqj Afksbn ==== Control System - PLC: SIEMENS S7-1200 - Operation: pendant panel / wired remote control - Control: manual valve + electric control - Optional: 7" touchscreen - Optional: wireless remote control - Optional: up to 99 programs storable ==== Safety - Hydraulic overload protection - Electronic overload protection - End travel safety switches (top/bottom) - Safety PLC - CE-compliant design - Optional: safety edge on portal columns ==== Electrical Connection - Main supply: 400 V AC - Control voltage: 24 V DC - Frequency: 50 Hz - Main motor: 11 kW - Total connected load: approx. 18 kW Fields of application: Straightening, tool and mold making, steel construction, heavy forming, maintenance, try-out, alignment work (Hydraulic press, hydraulic straightening press, portal press, portal straightening press, 300-ton press, 300 t press, H-frame press, heavy-duty press, industrial press, forming press, straightening system) ##### The images shown serve as samples and may deviate from the actual configuration.

Condition: new, Year of construction: 2019, pressing force: 275 t, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec :2-50 mm/sec. Cylinder hub:900 mm Gjdpsfxyigjfx Afksbn Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: as good as new (ex-display), Year of construction: 2021, pressing force: 135 t, It has a cylinder for 10 to 135 T and a small additional cylinder for 1500 kg to 7 T. Empty speed 2-10mm second pressing speed 2 mm second table size 1100x650x120mm 800 mm maximum open height table height max. 900 mm travel of the cylinder is 400 mm Gbsdpfjigg E Hjx Afken total height 2900 mm weight 2,3 T 200 L tank Pump with 60 L capacity 5 KW main motor Control system PLC SIEMENS or PILZ RSS4000- S 7 1200 Safety control system PILZ Communication operator/press Color touch screen 10" OMRON/SIEMENS