Underfloor coil carriage 30 t

ITALCOILS

Year of construction: 1994, condition: good (used), coil width: max. 2.000 mm coil weight: max. 30 t Crodpjlimrxjfx Amnjd stroke: 1.000 mm

Condition: excellent (used), functionality: fully functional, Year of construction: 1994, machine/vehicle number: SN1744271, Overheadcrane ± 11.550 mm x 5.000 kg Crodpfxev Ipvxj Amnsd

Condition: ready for operation (used), approx. 120 pieces = 480 running meters of safety conductor rails Number of conductors / number of poles: 5 in standard lengths of: 4 m Busbar cross section: 10 mm² for mains voltage up to: 500 V Load capacity at 100% ED: 60 A Cjdpfx Ajd Hurbemnord Weight per meter: 2.1 kg

Year of construction: 2016, condition: ready for operation (used), Absorption Refrigerator System with cooling tower Karlsruhe KRD 1/12-28-3. Cooling output: 214kW, permissible temperature: 10-60°C, max. overpressure: 1bar, nominal volume flow: 87.1m³/h, with Radial Fan Wolter GmbH TRZ 900/80 KTK and Absorption Chiller Carrier SCS 16LJ-03E-LC. Csdpfsn Tpmqjx Amnjrd

Condition: good (used), Year of construction: 1984, Overhead crane, crane, trolley, crane running gear, crane travel gear, girder travel gear, head girder for bridge cranes, ceiling crane head girder, head girder for single-girder bridge crane, head girder for double-girder bridge crane, double-girder traveling crane -Manufacturer: ABUS, 1 set of end plates for double girder overhead traveling crane -Type: ZLK -Drive motor: ABUS 0.12/0.55 kW Credpfx Aovt Rapomnsd -Carrier rollers: Ø 200 mm / groove width 60 mm -Dimensions: see photo technical drawing -Transport dimensions: 2970/855/H720 mm -Weight: 640 kg

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, Heavy-duty transport trolley for weights up to 35 tons. The transporter is supported by four pivoting heavy-duty wheels and two omnidirectional drive wheels (--> in any desired direction). The drive wheels are pneumatically pressed onto the ground to achieve optimal traction. By rotating the two drive wheels, the various drive modes of the transporter are activated. This creates a very flexible transporter that can move longitudinally, laterally, and rotate on the spot. The transporter integrates a 35-ton lifting table, the contact surfaces of which are equipped with heat sinks to dissipate the heat emitted by the pallet (during the transport of warm/hot material). The lifting system is driven by a central motor, and the power transmission takes place via two gearboxes and axles that run through the frame. These axles drive 4 shafts at the corners of the transporter. Depending on the transport goods, a device can be constructed that is supported by the lifting system. The entire system is protected by aluminum covers, each of which is numbered so that it can be easily reattached in the correct position after maintenance. The transporters are designed to move a maximum load of 35 tons with a maximum speed of 1.5 km/h in manual mode and 1 km/h in semi-automatic mode. The speed can be adjusted continuously via the manual control with joysticks. Without a load and in manual mode, the transporter can reach 2.5 km/h; in semi-automatic mode, the speed is limited to 1.5 km/h. Cedpfx Amjxa Endjnord Control: SIEMENS SIMATIC Operation: Radio remote control Drive: Battery-powered Dimensions approx. 3600 x 2500 x 800 mm

Condition: good (used), Indoor crane, crane, trolley, crane running gear, crane undercarriage, girder undercarriage, headcarriage for bridge cranes, ceiling crane headcarriage, headcarriage single girder bridge crane -Manufacturer: Demag, 1 set of end carriages for single girder bridge crane -Load capacity: 3000 kg Cjdpfx Ajtpkv Aemnerd -Drive motor: Mannesmann Demag 16I6 KF 8-2 0.15/0.60 Kw -Support rollers: Ø 160 mm / support width 148 mm, dimensions see photos -Dimensions: 2300/650/H570 mm / 300 kg each -Transport dimensions: 2300/1230/H570 mm -Weight: 600 kg/total

Year of construction: 1990, condition: good (used), coil weight: max. 15 t Crjdpfx Ajbibu Tsmned coil OD: max. 1.800 mm

Year of construction: 1999, condition: used, CAPACITY 2000kgr ARM LENGTH 5M Crodpowa I Ucefx Amnsd HEIGHT 4.6M

Year of construction: 1974, condition: ready for operation (used), A Karstens cylindrical grinding machine with display is available. Center height: 180mm, grinding diameter: 360mm, center width: 650mm, max. workpiece weight flying/between centers: 70kg/250kg. Grinding wheel outer diameter: 400mm, face diameter: 250mm, peripheral speed: 35m/s, speed: 450rpm, mounting cone: MK4, quill diameter: 50mm, fine adjustment: 0.08mm. Machine dimensions X/Y: approx. 3250mm/2150mm, weight: approx. 3600kg. On-site inspection is possible. Codpfjvf Iy Rjx Amnjrd