Forklift

Hyster H7.00XL

Condition: used, functionality: fully functional, Year of construction: 2002, fuel type: gas, Forklift Hyster H 7.00 XL Year of manufacture: 2002 Gkodpfx Acsyvvuieieb Operating hours: 7432 Overall height: 3.25 m Lifting height: 4.4 m Fork carriage width: 2 m Full cab with heating Free auxiliary hydraulics With sideshift Forks 1.2 m and new forks 2.4 m

Condition: ready for operation (used), Year of construction: 2021, A Wacker Neuson wheel loader, ideally suited for agricultural purposes, is available. Engine: Deutz TD 2.9 L4 S5, Power: 61hp/45kW, Displacement: 2900cm³, Emission standard: Stage V, Exhaust aftertreatment: DOC/DPF, Max. engine speed: 2300rpm, Max. tipping load: 3300kg, Standard bucket capacity: 0.8m³, Max. working hydraulic pressure: 220bar, Max. travel hydraulic pressure: 450bar, Fuel tank: 82l, Kinematics: Z, Articulation angle: 44°, Oscillation angle: +/-12°, Max. dump height: 2430mm, Lifting force: 41.36kN, Outside turning radius: 3870mm, Tires: 405/70 R20. Transport dimensions X/Y/Z: approx. 4800mm/1850mm/2550mm, Operating weight: approx. 4600kg, Operating hours: approx. 1382h. Including 1200mm pallet forks, FEM II rotating fork positioner, road approval and hydraulic Z-HV quick coupler. The engine or the control system of the windshield washer system has a defect. Documentation available. An on-site inspection is possible. Gkodpfx Aezhw Skociob

Year of construction: 1975, condition: good (used), functionality: fully functional, drive type: Diesel 130 Kw, Patrol boat from the former GDR, later used by the Berlin Water Police (WSP 1), IFA 6-cylinder diesel engine. Winter-capable, icebreaker rating up to 3 cm thickness, certified for all waters including open sea. Dimensions: 11.90 m length, 2.90 m beam, draft 0.90 m. Top speed: over 30 km/h. Engine: Schönebeck 6-cylinder, 4-stroke diesel, type DM 6 VD 14.5/12-1. According to research, the engine delivers either 170 or 220 HP from 10 L displacement. These engines are known for low fuel consumption: at canal cruising speeds (8–12 km/h), consumption is 6–8 L per hour. Gedpfx Aoy D Rk Iecijkb Equipment includes signal mast, mast spotlight, boat lighting. Dual helm positions: inside cabin and flybridge. AGM batteries, engine start with 24 V system, 12 V onboard network. Brand new onboard toilet. Electric and manual bilge pumps (automatic/manual operation). Complete overhaul from 2021 to 2023: 5-layer primer and 3-layer antifouling coating. Steel hull, aluminium superstructure. New electrical wiring, new exhaust system, new clutch, engine overhauled, fuel tank serviced, new lines installed, new air filter. Engine starts and runs flawlessly, forward and reverse gear shifts without issues. Some work is still required to complete comfort features. The vessel is suitable as a small tugboat or as a work or fishing boat. Lower helm station: the gauges still need to be installed; required instruments and switches are included.

Condition: good (used), functionality: fully functional, Sheet width: 4050 mm Sheet thickness: 8 mm Cutting angle: 2 - 10° Cutting speed: 0.053 m/s Gkedpfexu Nc Ijx Acijb Table length: 710 mm Machine weight approx.: 10,100 kg

Condition: used, Year of construction: 2012, x-travel 2100 mm y-travel 1020 mm z-travel 762 mm Control Fanuc MXP-200FP spindle speed 6000 U/min spindle capacity ca. 22 kW max. torque on the spindle ca. 550 Nm tool taper SK 50 table surface area 2300 x 1020 mm Gsdpox Sr A Ujfx Aciokb max. table load 3000 kg T-slots 6 x 22 mm T-slot - distance 150 mm 3-Axis CNC Machining Center Equipment/Accessories: - Automatic tool changer with chain magazine, 40 stations - max. tool-Ø: 120/240 mm - max. tool length: 350 mm - coolant system with internal coolant supply and filter - emulsion mist extraction - electronic handwheel - 2 pcs. magnetic clamping plates 800 x 400 mm - various tool tapers SK50 - chip conveyor

Condition: used, WEBSTER & BENNETT EV 36” HIGH SPEED VERTICAL BORER MAKE WEBSTER & BENNETT, MADE IN ENGLAND MODEL EV 36” TABLE DIA 915 mm SWING 1168 mm HEIGHT UNDER RAIL 533 - 1016 mm SPEED 13.5 - 300 rpm FEED RATE 0.005-0.250 inch/min MAIN SPEED 40 HP PLUS HIGH SPEED TAABLE EV SERIES MACHINE ELEVATING RAIL SAFETY GAURDING SET OF JAWS Godpfxexp Na Ns Acijkb FULLY FUNCTIONAL GOOD SLIDES

Condition: new, pressure 100 t stroke 400 mm 1010 mm 295 mm Heads 175x115 mm feed down 7,6 mm/sec feed up 13,4 mm/sec total power requirement 4,0 kW weight of the machine ca. 1000 kg dimensions of the machine ca. 1600x850x2450 mm Domestic equipments: - Stable welded construction - Pressure cylinder laterally adjustable - Electric control via selector lever / manually via hand lever - Pressure gauge via pressure gauge Gksdpfsyv N Ngox Acisb - Material requirements - CE mark

Condition: used, functionality: fully functional, Year of construction: 2019, operating hours: 873 h, load capacity: 5,000 kg, lifting height: 3,300 mm, fuel type: diesel, mast type: duplex, construction height: 2,450 mm, fork carriage width: 1,200 mm, fork length: 2,400 mm, empty load weight: 7,850 kg, drive type: Diesel, construction width: 1,450 mm, Diesel forklift Load center: 600 Mast type: Duplex Technical condition: good Front tire size: 300-15/8.00 Gjdpfjvgh U Rex Acijkb Rear tire size: 7.00-12/5.00 Sideshift, 3rd valve, 4th valve, front working lights, heater, full cab, CE certificate, safety light,

Condition: new, Year of construction: 2012, welding current 20 - 100 A cutting capacity max. 35mm mm Gkedpjw En E Eefx Acieb open-circuit voltage 250 V Required air-pressure min. 4 bar connected load 20 KVA connected load frequency 400 V weight 0,7 kg Dimensions (LxWxH) 1,0 x 0,6 x 0,8 mm Plasma cutting machine with cart - Includes 7m hose package - Spare nozzles

Condition: used, O F F E R We can offer you ex stock, subject to prior sale and errors: TSCHUDIN (CH) Centerless cylindrical grinding machine Model TC-300 Year of manufacture 2001 Grinding range – Ø 0.5 – 25 mm (30) Max. workpiece length for plunge grinding 125 mm (140) Max. workpiece length for through-feed grinding 300 mm Grinding wheel dimensions: Ø x width Ø 300 x 125 mm (140) Regulating wheel dimensions: Ø x width Ø 225 x 125 mm (140) Grinding wheel peripheral speed 35 m/sec Grinding wheel infeed 3 mm Regulating wheel speeds, steplessly adjustable 0 – 444 rpm Regulating wheel inclination Degrees Grinding wheel drive approx. 7.5 kW Total connected load approx. 13 kW – 380 V – 50 Hz Weight 2,500 kg Accessories / Special equipment: • The machine operates with a fixed workpiece position, allowing both the grinding spindle and the regulating spindle units to be adjustable. This simplifies machine setup as well as automatic workpiece loading and unloading. • SIEMENS PLC control for automatic operation with SIEMENS touchscreen. Complete electrics and PLC control renewed in 2016! • Electromechanical profile dressing device for the regulating wheel • Regulating and grinding wheel speeds are steplessly adjustable. • Adjustable plunge guide bridge with mounted plunge workpiece rest • Electromechanically controlled workpiece pusher & automatic pneumatic workpiece ejector • Additional outfeed cylinder for automatic tilting of workpieces after plunge grinding (adjustable 4–30 mm) • Machine is prepared for use with a HELP-TEC bar loader MSHL08/400P, which is currently not present. Gjdpfowftt Uex Aciekb • Complete enclosure of working area with monitoring technology • Separate control cabinet, operating and electrical manuals for the retrofit Condition: Very good! Fitted with new electronics in 2016! Click here for a video of the machine: Delivery: ex stock, immediately available, FCA Metzingen Payment: strictly net – after receipt of invoice Always a large selection of grinding machines in stock – please inquire for your requirements!