Hydraulic guillotine shear

HACO HSLX 4006

Condition: used, Year of construction: 2009, sheet width 4050 mm plate thickness 6.50 mm Hedoxaccropfx Afnefc thickness at "Niro-steel" 4.00 mm back stop - adjustable 1000 mm no. of strokes 6 - 11 Hub/min work height max. 880 mm Control SC 70 cutting angle 0.5 - 3.0 ° down holder 23 Stück engine output 11.0 kW weight of the machine ca. 7500 kg range L-W-H 4950 x 1950 x 1720 mm Machine made from light metal production (ALU) good condition including special accessories such as sheet metal holding device - in checked condition - machine video - ?v=pv7RRijDXJA Furnishing: - electro-hydraulic/blade-guided guillotine shears - HACO CNC control model SC 70, swiveling at the front left * Pre-selection positioning of the backgauge * Digital display of actual position value * electro-hydraulic cutting angle adjustment * electro-hydraulic cutting gap adjustment * programmable retraction from the backgauge * Programmable cutting length limit * Emergency switch - electro-hydraulic cutting gap adjustment - electro-hydraulic cutting angle adjustment - electro-motorized back gauge, on ball screws - hydraulic hold-down devices - front finger protection - Ball rollers in the support table - 1x side stop, with mm scale - 1x freely movable foot switch - rear guard - original operating instructions including CE declaration Special accessories included: - pneumatic sheet metal holding device for thin sheet metal blanks * for sheet thicknesses up to max. 4.0 mm * optimal positioning of thin sheets

Condition: ready for operation (used), sheet thickness steel (max.): 10 mm, back gauge: 1,000 mm, power: 21 kW (28.55 HP), total length: 4,330 mm, total width: 2,200 mm, total height: 2,110 mm, empty load weight: 10,000 kg, workpiece length (max.): 3,100 mm, CNC Siemens achteraanslag en snijhoekverstelling 2 voorste steunpunten van 3 meter Handmatige afstelling van de messpeling Instapbeveiliging aan de achterzijde Strokes/min: 9 > 40 str/min Hodpfx Afjv Taiaonsfc Adjustable cutting device: 0,1 > 1,5 mm Backgauge: 1000 mm Siemens Adjustable cuttingedge: 0,5° > 2,5° Courant needed: 380V Number of sheet holders: 17x

Condition: good (used), Year of construction: 2002, HEIDENHAIN TNC 430 control Spindle speed 20–9,000 rpm Hjdowglfxepfx Afnefc Travels X = 500, Y = 400, Z = 400 mm Tool holder SK 40 16-station tool changer Rotary table with B and C axes Clamping surface Ø 700 x 500 mm Max. table load 200 kg Infrared probe for workpiece measurement

Condition: new, Year of construction: 2025, functionality: fully functional, Blasting container for blasting with glass beads, ceramics, corundum, hard cast gravel, garnet sand, etc. Blasting container with full-surface screw conveyor floor and real blasting agent preparation. No sweeping, vacuuming and shoveling of abrasive in the blast room during the blasting of your workpieces thanks to our circulation system. Hfjdpfx Afeuwlzyonjc Blast media cleaner air separator 4-fold adjustable air volume/ flow speed/ suction proximity to the blast media/ blast media layer height adjustment. Electric vibrating screen for permanent coarse separation. Bucket elevator with trapezoidal threaded spindle for belt tensioning and speed monitoring. Container lining with a 70shore 4mm fabric rubber for a service life of up to 30 years with proper use. Container can be opened completely to the side for easy forklift loading. Container can be upgraded with a crane overhead hatch, floor reinforcement, lateral blast room extension. When blasting stainless steel, the container can be upgraded with a real magnetic drawer or a magnetic drum separator as well as stainless steel grating. Filter system with easy maintenance doors, big bag dust bagging, H13/14 secondary filter and silencer. Blast pot with pressure regulator and water separator. The container is characterized by its reliability and easy maintenance. All system components are easily accessible at the rear of the container. Only 4 ball bearings on the screw conveyor floor and 4 ball bearings on the bucket elevator. Special warranty of 5 years on the essential parts of the blasting system included. Safety equipment: Door/gate limit switch, dead man's control, emergency lighting, blast room viewing window, emergency stop in the blast room and on the outside of the control cabinet, pressure vessel quick ventilation

Condition: reconditioned (used), Year of construction: 2007, functionality: fully functional, travel distance X-axis: 3,500 mm, travel distance Y-axis: 1,250 mm, travel distance Z-axis: 1,000 mm, feed rate X-axis: 25,000 m/min, feed rate Y-axis: 25,000 m/min, feed rate Z-axis: 25,000 m/min, spindle speed (max.): 3,000 rpm, spindle speed (min.): 20 rpm, table width: 850 mm, table length: 3,700 mm, overall weight: 18,500 kg, RepairFIT by Dornhöfer The Difference. Including installation & commissioning! Year of manufacture: 2007 Travel / Stroke Capacities: Longitudinal (X): 3,500 mm Vertical (Y): 1,250 mm Cross (Z): 1,000 mm Table dimensions: Length: 3,700 mm Width: 850 mm T-slots: 5 x 22 H12 Reference slot: 1 x 22 H8 T-slot spacing: 140 mm Paintwork: RAL 5011 (steel blue) RAL 7035 (light grey) Tool holder: ISO 50, DIN 69871 AD Pull stud: DIN 69872 Form A Main drive: Drive power: 100% duty cycle 24 kW Spindle speed range: Spindle speed: 20-3,000 rpm Torque: 479 Nm Max. feed rate: X, Y, and Z axes 25,000 mm/min Mean acceleration: 2 m/s² Weight: approx. 18,500 kg HEIDENHAIN iTNC 530 HSCI Swiveling control pendant including Heidenhain iTNC 530 control (1 processor / 4 axes) with software options 1 and 2. Automatic Milling Head, Diagonal H4 Automatic indexing Soraluce “Diagonal” milling head, Type H4 / 2 planes with 2.5° x 2.5° indexing, 479 Nm, tool clamping force 18,000 N. Automatic tool changer: Automatic tool changer (random carousel) with 20 magazine positions: The automatic tool change is carried out in the vertical position of the tool spindle. Maximum tool diameter: 125 mm Maximum tool length: 250 mm Maximum tool weight: 15 kg Number of magazine positions: 20 Chip conveyor package: Three chip conveyors, two longitudinal screw conveyors and one cross hinge belt conveyor with integrated coolant tank, discharge height: 1,000 mm Coolant System 2: Coolant/lubricant system 2 with discharge via shower ring and internal coolant supply according to DIN 69871 Form AD, tank capacity 500 l + 150 l lift tank with pump, delivery rate 50 l/min, delivery pressure 5/8 bar. Increased delivery pressure of high-pressure pump from 15 bar. RepairFIT is our proven offer for a profitable entry into our product lines. Hfjdpjxgn Efjfx Afnoc The machines available in this line are sourced by us following a strict selection process and undergo a thorough inspection (deep-dive check). After intensive cleaning, all identified visible defects and faults are professionally repaired by our expert service team.

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm Hfedpfjwu Tu Dox Afnec 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Year of construction: 1977, condition: used, Weiler Matador VS2 lathe year ca.1977 with collets , collet tube , three-jaw chuck , Multifix. Guide in the front area shrunk. Machine in a ready to use condition , After consultation under power ready for demonstration. Hfjdpfx Aomdn Dxefnec

Condition: excellent (used), Year of construction: 2000, pressure 105 t chamfer lenght 3100 mm distance between columns 2600 mm table width 100 mm table height 750 mm Control DELEM DA 65 dayligth 200 mm working feed 0 - 10 mm/sec return speed 0-100 mm/sec rapid traverse - up max. 100 mm/sec voltage 380 V / 50 Hz total power requirement 11 kW Hsdpfx Ajvq R Uujfnefc weight of the machine ca. 7,5 t dimensions of the machine ca. 4 x 2,2 x 2,8 m Equipment: • CNC-control DELEM DA65 graphic video • controlled backgauge 2 axis • upper and lower tool • 2 hand control / foot switch

Condition: as good as new (ex-display), Year of construction: 2022, Press design double column press Thermally neutral 80 - 120 °C Number of operating sides 1 side Forces Pressing force max. 4000 kN Hodeph Uk Nspfx Afnofc Free ripping force max. 400 kN Pressure build-up time Closed die steel to steel Max. 4 sec. Dimensions 3,800 mm long and 4,475 mm wide Max. Opening width 800 mm Stroke 800 mm Table height above floor 1100 mm Height above floor (headroom) approx. 4300 mm Hall height min. 5500 mm parallel deviation at 20°C +/- 0,1 mm Deflection Determined at max. clamping force with 70% occupancy < = 0.2 mm/m Weight Total weight of press without operating materials and table plate approx. 28 t Press table Table size 1500x1500 mm Speeds Fast closing with 100 mm sec. Pressing speed 8 - 3 mm sec. Sound pressure Sound pressure level, measured at 1.5m height at the control panel according to DIN 45635-T16-KL3 max. 78 db(A) Hydraulics Number of pressing cylinders/driving cylinders 1 pc. Operating pressure max. 300 bar Pressing pressure build-up time 4 sec. Pressure accuracy during pressing stroke +/- 3 bar Main pump BOSCHREXROTH axial piston pump approx. 145 L/min Oil volume approx. HLP 46 MW 1000 liters Ambient temperature max. 40 °C Oil temperature max. 55 °C Flow temperature °C Auxiliary pump BOSCHREXROTH, gear pump 10 L/min Pressure stabilization for up to 300 sec. Electrical system Main supply 400 V AC Control voltage 24 V DC Frequency 50 Hz Connection hydraulics main motor 40 kW Sliding table press with 400 T capacity, Closing speed up to 100 mm/ ( adjustable via touch screen ) Opening speed up to 100 mm/sec ( adjustable via touch screen ) Starting press speed 10 mm/sec ( adjustable via touch screen ) table top size 1500x1500mm ram size approx. 1600x1500mm Oil temperature monitoring 55 degree warning, 60 degree shutdown Automatic lubrication ( adjustable via touch screen ) Free positioning of the ram ( adjustable via touch screen ) SICK/PILZ light barriers 14 mm, front, up to 1800 mm height Hydraulic and mechanical ram protection Circuit oil cooling ( adjustable via touch screen ) Ejector in table, 20 T press force, 350mm travel Ejector moves outwards with the table Table plate milled flat, with DIN 22 T grooves Pressure adjustment from 60 T to 400 T ( adjustable via touch screen ) Travel limitation either by pressure or position Set-up mode, single stroke and cycle sequence ( adjustable via touch screen ) Swiveling control panel on the cabinet Two-hand operation, with opening button, manual/single stroke/cycle switchover button Installation, commissioning, instruction against separate charge The control is supplied by SIEMENS. ( S 7 1200 ) Also the touch screen monitor with 9 inch. The remote maintenance unit SECOMEA -Ethernet is included in the delivery. The side of the press has two 1000 mm high and 800 mm wide windows with double doors. (sliding table press, hydraulic press, hydraulic press, double column press)

Condition: excellent (used), functionality: fully functional, Pantograph with 2 controlled axes, ideal for machining aluminum, PVC, and steel profiles up to 2 mm, with the option to process stainless steel (optional). The work cycle is managed through intuitive software that guides the operator with simple instructions on the touchscreen display. The USB connection allows for easy linking to a PC. The four-sided rotating worktable ensures very high precision by using shorter tools, thus avoiding through machining and the resulting issues of vibration and noise. It is equipped with a quick tool change system with ISO 30 taper. A retractable, pneumatically operated guard protects the operator during machining. Hedpex U Dg Djfx Afnofc