Glue spreader

Gannomat Selekta 253 - sofort verfügbar -

Condition: new, Year of construction: 2026, For professional and precise glue supply in dowel holes and back side grooves. Short introduction: • Always the same and right glue amount • No afterwards cleaning of the workpieces of too much glue is necessary • Easiest and minimal cleaning (1x week) of the gluing system (through cleaning program) • Glue cost savings Hedpsdxz Tpjfx Ac Tjt • Ergonomic and light glue gun compared to squeezy glue bottles • Faster and more precise working compared to squeezy glue bottles

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, * Wemhöner Basic 1000 Plus - Year of manufacture: 2008 - Very good condition, little used * Type: KT-MB-28/15-240 * With automatic pin system and inline turn-over device * 2 tables with automatic variable pin system * With Teflon coating for pre-glued foil * Foil laying system for the pin table (pre-glued foil) * Heating plate size: 2800 x 1500 mm * Maximum workpiece size: 2,540 x 1,250 mm * Membrane: Yes * Cutting station * Foil paternoster storage, 3.2 m height with 14 suspension rods * Siemens S7 PLC control * Operator panel for PLC control: SIEMENS TP 270 (touchscreen) * Automatic membrane tensioning * Installed power supply: 38.5 kW * Maximum chamber pressure: 6 bar * Maximum press opening: 150 mm * 6 cylinders with Ø 125 mm * Operating voltage: 400V 50/60Hz * Press chamber height: 40 / 60 mm * Max pressing force: 2400 kN * Hydraulic system operating pressure: 320 bar Hjdpfx Asxbcudjc Tet

Condition: used, Valon Kone VK26M Hodsvgtz Njpfx Ac Tet With infeed and outfeed conveyors.

Year of construction: 2004, condition: ready for operation (used), Max. working width: 1000mm, feed rate: 5-20m/min, height: 2200mm, length: 4000mm, weight: 3.3t, with documentation, was maintained regularly. Hodpfxsi E Trps Ac Tet

Condition: good (used), Swivel Spindle Milling Machine, Table Milling Machine, Bench Milling Machine -Spindle adjustment: height and angle -Swivel: -3° to 45° -Drive: 4.5/5.5 kW Hsdpfx Acoh Nvyzj Tjt -Speed: 3000/4500/6000/9000/12000 rpm -Feed apparatus Holz-Her 3 rolls -Useful shaft length: 100 mm -Spindle: Ø 30 mm -Max. Milling cutter: Ø 220 mm -Dimensions: 1540/1100/H1520 mm -Weight: 962 kg

Year of construction: 2004, condition: excellent (used), Four-side planer -max. planing width 23cm Hjdpfehlp D Nsx Ac Tjt -max planing height 16cm -2 pulling rollers in the table -chromed table - smooth regulation of the feed speed -2 pulleys from the top in front of the lower head, additionally a roller apparatus for short elements - 4 spindles: lower 5.5kW, right 5.5kW, left 5.5kW, upper 7.5kw The machine is in very good condition, little used, with spiral heads on the bottom right and left, with a Terssa knife head on the top.

Condition: new, Year of construction: 2025, Gannomat Concept 70 Eco Laminate – Body press with rapid traverse Technical data: Hsdpoiidm Nofx Ac Tet Laminate body press from our showroom; Working area: width from 150 – 2,500 mm, height from 150 – 1,400 mm; depth 700 mm; - Laminate press beam at the top with 6 elements, laminate press beams on the side with 5 elements - Laminate press beams with proven tolerance compensation for tight body joints - Counterpressure surfaces are 40 mm thick, coated, continuous support plates - The pressing force of the press beams is continuously adjusted electronically via 2 potentiometers and set via a frequency converter, therefore, the torque transmission is absolutely wear-free. - Pressing force for horizontal press beams min. 500 daN (kg) to continuously max. 2200 daN (kg) - Pressing force for vertical press beams min. 300 daN (kg) to continuously max. 2200 daN (kg) - Including option: Rapid traverse speed for quick positioning of the press beams, controlled via automatic workpiece detection with sensors in the press beams, pressing speed 5/10/25 mm/sec. and rapid traverse speed 50 mm/sec, the sensors can be switched off for pressing special parts. - Tapping mode for precise positioning of the two press beams, e.g. for low pressing forces, drawers and bodies at 45 degrees. Simple operation via 6 separate push buttons, freely adjustable preselection of pressing time with automatic opening, loading height 300 mm The machine is in our showroom and can be delivered immediately. Location: in stock at 54634 Bitburg - immediately available -

Condition: excellent (used), belt driven Flow rate 14500 m3/h Negative pressure 3091 Pa Motor power 22 kW Speed ​​2340 rpm Suction DM 500 mm Outlet DM 400 x 500 mm Dimensions L x W x H = 1800 x 1300 x 1250 mm Hedpfxjh Tfqhe Ac Tot Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: new, A dedicated machine for producing a straight trench / notch in a variety of timber products used in general joinery, garden furniture, shed, roof truss and timber frame manufacturing. Also can be used for door framing, notching of roof bearers and for log cabin manufacture.As standard the machine is fitted with horizontal pneumatic workpiece clamps and also a hydrocheck damper control to give a smooth stroke action to the cutterhead movement. Hodpfxjdy Hm De Ac Tst Precision ball bearing movement on hardened steel runners. Sturdy cast iron construction with steel base stand. 3kw motor. Max tool dia 250mm Bore of tool 40mm. Handwheel rise and fall of cutter motor arm. Max depth of trench / notch 60mm. Width of trench / notch 60mm - in one pass. Max. length of travel of tool 250mm. 2 x horizontal workpiece clamps. Hydrocheck damper to movement of cross cut arm. Dust extraction outlet 100mm. Machine stand

Condition: used, - Adhesive application with 1 profiled roller for Packaging height 300mm over 1 application roller - The drive via worm gear motor 0.37 kW Hodpfxecht Nys Ac Tjt - 1 ST left - 1 ST right - Fits DIMTER HK 200 and HK 400 spare parts dimter in stock equipment in stock accessories in stock