Low loader semitrailer

FAYMONVILLE MAX Trailer MAX100 Semi-Tieflader Radmulden

Condition: new, maximum load weight: 36,360 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete range of vehicles, including those available immediately or at short notice, on our website. Excerpt from the equipment list. Full equipment details available upon request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick Loading Platform: * Telescopic loading platform with rear slope approx. 1,000 mm x 8° * 1 pair of fixed wheel recesses in front of the axles, approx. 2,850 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing laths approx. 15 x 15 mm, including extensions at the bottom * Between the 1st and 2nd axle, one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) * Incl. 3-piece removable galvanized covers over the wheel recesses (width approx. 670 mm) – max. point load 5 t each * Recess in the slope and extending into the platform for accommodating an excavator dipper stick (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of horizontal lashing rings at the front of the platform (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 2 pairs of fold-out lashing rings (LC 10,000 daN) * 2 pairs of lashing rings in the excavator stick recess (LC 5,000 daN) * Cut-outs in the platform's outer frame for attaching tie-down straps (LC 2,000 daN) Two-Piece Steel Ramps: * One pair of galvanized, two-piece steel ramps, approx. 2,750 + 1,400 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulically folding ramp sections and hydraulic lifting system, hydraulically adjustable * Maximum load per pair: 40,000 kg Landing Gear: JOST landing gear (mechanical) with 2-speed gearbox, lift capacity approx. 24 t (test load approx. 50 t) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reverse lock, activated automatically by reverse gear and manually * Air suspension with lift and lower valve Tyres: * 235/75 R 17.5 3PMSF tyres – manufacturer of our choice TPMS: * TPMS tyre pressure monitoring system in accordance with ECE R 141 Brake System: * WABCO brake system according to EU regulations with EBS-E (2S2M) Paintwork: * HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc / 15% aluminum) for optimum corrosion protection * Final paintwork with two coats of 2K topcoat, solid RAL 3002 Carmine Red, in accordance with RAL System 841GL Ffjdpfxeyhkq Ue Ag Dow * Wheel rims in silver grey Incl. the following additional equipment: * 2-inch king pin * One galvanized steel front wall, approx. 400 mm high * 3 pairs of recessed lashing rings along the central beam (LC 5,000 daN) * Electro-hydraulic power unit at the rear, under the loading platform * On the gooseneck: plug-in aluminum drop sides and tail board, approx. 2,440 x 400 mm (L x H). The rear galvanized stakes are removable (body length approx. 2,560 mm). * One galvanized toolbox integrated in the gooseneck chamfer * 2 pairs of WADER container pockets on the loading platform for a 20' or 30' container * 3 pairs of stake pockets for plug-in stakes approx. 100 x 50 mm in the outer frame of the platform * 3 additional pairs of removable galvanized covers over the wheel recess – max. point load 3.5 t each * One removable galvanized intermediate table with 1 pair of WADER container pockets * 1 additional, hook-on intermediate table, approx. 300 mm wide * Intermediate table with offset load ar

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck Ffsdpfxoh Hm Tzo Ag Dsw -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, maximum load weight: 37,820 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our entire vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpt from the equipment. Full equipment details available upon request. Ffsdpfx Asw Tpqwog Dew Gooseneck: - Gooseneck with beveled front corners approx. 45° and rear chamfer approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood floor covering approx. 30 mm thick Loading area: - 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) - Wheel recesses with square climbing slats approx. 15 x 15 mm and widenings in the lower section - Between the 1st and 2nd axles, a pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load approx. 5 t/each - Recess in the chamfer and extending into the loading area for receiving the excavator bucket arm (approx. 2,900 x 750 x 210/290 mm (L x W x H)) - 1 pair of lashing rings, horizontal, at the front of the loading area (LC 10,000 daN) - 5 pairs of flip-out lashing rings (LC 5,000 daN) - 3 pairs of flip-out lashing rings (LC 10,000 daN) - 2 pairs of lashing rings in the excavator arm recess (LC 5,000 daN) - Cut-outs in the outer frame of the loading area for securing straps (LC 2,000 daN) One-piece Steel Ramps: - One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering - Ramp with hydraulic lifting mechanism, hydraulically adjustable - Maximum load per pair: 40,000 kg - In accordance with Regulation 1230/2012/EU, ramps with a length less than 300 mm do not count towards the vehicle length in the driving position Landing gears: - JOST landing gears (mechanical) with 2-speed gearbox for approx. 24 t lifting capacity (approx. 50 t test load) Axles: - BPW axles and suspension, 2 fixed axles, 1 trailing steering axle - Technical axle load: 12,000 kg each - Electromagnetic reverse lock, activated via reverse gear and manually - Air suspension with lift and lower valve - Axle tool kit Tyres: - Tyres 235/75 R 17.5 3PMSF – manufacturer of our choice - TPMS tyre pressure monitoring system in accordance with ECE R 141. The data transmission to the truck is via standardized EBS interface according to ISO 11992. For correct display, the truck must be able to transmit and display this data Braking system: - WABCO braking system in accordance with EU regulations with EBS-E (2S2M) without connecting lines to the tractor unit Steel construction: - Steel structure made of high-tensile fine-grain steels - Steel grades: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Electrical system: - Electrical system according to EU regulations - Lighting 24 volts ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at the front connection strip with 24N, 24S & 15-pin sockets as per ISO. 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: - Complete steel structure automatically shot-blasted with blasting wheel machine after welding - Second shot-blasting using corundum for optimal coating adhesion - HRM metallization of the entire vehicle chassis with ZINACOR 850 (85% zinc/15% aluminum) to ensure maximum corrosion protection - Final painting with 2 coats of two-component topcoat, single color in RAL 3002 Carmine Red, according to the RAL system 841GL - Rims in silver - Rear section metallized and in RAL 9010 (continuation see ori

Condition: new, maximum load weight: 37,635 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment features. Complete specifications available on request. Gooseneck: * Gooseneck with front corners beveled approx. 45° and rear chamfer approx. 750 mm x 10° * 3 pairs of lashing rings (LC 5,000 daN) * Hardwood flooring approx. 30 mm thick One-piece steel ramps: * One pair of galvanized one-piece steel ramps, approx. 3,000 x 800 mm, with approx. 48 mm thick hardwood covering * Ramps with hydraulic lifting mechanism, hydraulically adjustable * Maximum load per pair: 40,000 kg In accordance with Regulation 1230/2012/EU, ramps shorter than 300 mm in driving position do not count towards the vehicle length Loading area: * 1 pair of fixed wheel recesses in front of the axles, approx. 2,610 x 970 x 400 mm (L x W x D) * Wheel recesses with square climbing strips approx. 15 x 15 mm as well as extensions in the lower area * Between the first and second axles, one pair of fixed wheel recesses, approx. 1,610 x 700 x 400 mm (L x W x D). Includes three-piece removable galvanized covers over the wheel recesses (W approx. 670 mm) – max. point load 5 t/each * Recess in the inclined area as well as projecting into the loading area to accommodate excavator boom (approx. 2,900 x 750 x 210/290 mm (L x W x H)) * 1 pair of lashing rings (horizontal) at the front of the loading area (LC 10,000 daN) * 5 pairs of fold-out lashing rings (LC 5,000 daN) * 3 pairs of fold-out lashing rings (LC 10,000 daN), 2 pairs of lashing rings in the excavator boom recess (LC 5,000 daN) * Cut-outs in the outer frame of the loading area to hook in tensioning straps (LC 2,000 daN) Landing legs: * JOST landing legs (mechanical) with 2-speed gearbox, lifting capacity approx. 24 t (test load approx. 50 t) Axles: * BPW axles and suspension, 2 rigid axles, 1 trailing steering axle * Technical axle load: 12,000 kg each * Electromagnetic reversing lock, activated via reverse gear and manually * Air suspension with lift/lowering valve * Axle tool kit Tyres: * Tyres 235/75 R 17.5 3PMSF – brand at our discretion * TPMS: Tyre Pressure Monitoring System in accordance with ECE R 141. Data is transmitted to the tractor via standardized EBS interface according to ISO 11992. For correct display, the tractor unit must be able to receive and display this data Braking system: * WABCO brake system in accordance with EU regulations, with EBS-E (2S2M) and without connection lines to the tractor unit Ffodpfx Agoxtc Ubj Dow Steel construction: * Steel structure made of high-strength fine-grained steels * Steel grades: S355J2+N/S355MC (yield strength 355MPa), S690QL/S700MC (yield strength 690MPa) Electrical system: * Electrical system in accordance with EU regulations, 24-volt ASPÖCK-NORDIK (ASS3) lighting * ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets * Connections according to ISO: 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Paintwork: * Complete steel construction automatically shot-blasted with turbine blasting machine after welding * Second blasting treatment with corundum for optimum coating adhesion * Final coating with 2 layers of 2K topcoat, single color in RAL 3002 Carmine Red as per RAL system 841GL * Rims in silver * Rear section metallized and painted in RAL 9010 (Pure White) * Paint system tested in salt spray mist test according to ISO 9227-NSS * Cavity sealing with special wax Including the following extras: * 2-inch kingpin * One

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position Fsdohlz R Sjpfx Ag Defw -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: new, maximum load weight: 38,140 kg, overall weight: 48,000 kg, axle configuration: 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and at short notice, on our website. Excerpt from equipment. Full equipment details available on request. Gooseneck: - Gooseneck with front corners chamfered approx. 45° and rear bevel approx. 750 mm x 10° - 3 pairs of lashing rings (LC 5,000 daN) - Hardwood flooring, approx. 30 mm thick Loading area: - Telescopic loading area with rear incline approx. 1,000 mm x 8° - Between 1st and 2nd axle: one pair of fixed wheel recesses, approx. 1,610 x 970 x 400 mm (L x W x D) - Incl. 3-piece removable galvanized cover over wheel recesses (width approx. 670 mm – max. point load 5 t / pc.) - 1 pair of flat lashing rings at the front of the loading area (LC 10,000 daN) - 4 pairs of outward folding lashing rings (LC 5,000 daN) - 3 pairs of outward folding lashing rings (LC 10,000 daN) - Cutouts in the outer frame for attaching tie-down straps (LC 2,000 daN) Landing legs: - JOST landing legs (manual) with 2-speed gearbox for 24 t lifting capacity (50 t test load) Tyres: - Tyres 235/75 R17.5 3PMSF, make at our discretion - TPMS tyre pressure monitoring system in accordance with ECE R 141 - Data transfer to the towing vehicle via standardised EBS interface as per ISO 11992 - For correct display, the towing vehicle must be able to receive and display this data Axles: - BPW axles and suspension, 2 axles rigid, 3rd axle self-steering - Technical axle load: 12,000 kg - Electromagnetic reverse lockout activated automatically when reversing and manually - Air suspension with lifting and lowering valve. Axle tools Ffedpjw Tpq Dsfx Ag Dow Braking system: - WABCO braking system according to EU regulations with EBS-E (2S2M) without piping to the tractor unit Electrical system: - Electrical system per EU regulations - LED lighting 24 Volt ASPÖCK-NORDIK (ASS3) - All LED side marker lights flash with the indicator - ASPÖCK-UNIBOX at front connection strip with 24N, 24S & 15-pin sockets, according to ISO; 24N ISO-1185, 24S ISO-3731, 15-pin ISO-12098 Steel construction: - Steel structure made of high-strength fine-grained steels - Steel qualities: S355J2+N/S355MC (yield strength 355 MPa), S690QL/S700MC (yield strength 690 MPa) Paintwork: - Complete steel structure automatically shot-blasted after welding in a wheel-blasting system - Second shot-blasting with corundum for optimum coating adhesion - HRM metallization of entire chassis with ZINACOR 850 (85% zinc/15% aluminium) for maximum corrosion protection - Final painting with 2 layers of 2K topcoat, single-colour in RAL 3002 Carmine Red, rear section metallized and painted in RAL 9010 Pure White - Metallic finish not available - Paint structure tested in salt spray test according to ISO 9227-NSS - Internal cavities sealed with special wax Including the following accessories: - On the gooseneck and rear, left and right, one holder for warning signs each, including socket - Spare wheel holder in front of the front wall (without spare wheel) - 2-inch king pin - Galvanized steel front wall, approx. 400 mm high - Yellow-red air couplings on the galvanized front connection bar - Galvanized folding supports under the inclination at the rear of the loading area - A hardwood crash protection strip at the rear wall from gooseneck to the loading area - 1 pair of recessed lashing rings along the central beam at the rear inclination (LC 10,000 daN) - Aluminium drop sides and tailgate on the gooseneck

Condition: new, overall weight: 58,000 kg, Year of construction: 2026, Low loader semitrailer MAX100 4 A 8.60 U Technical data Speed 80 km/h Total weight 60,800 kg Fifth wheel load 18,000 kg Axle load 42,800 kg Empty weight Payload Gooseneck length 3,850 mm Fifth wheel height loaded 1,250 mm Loading area length 8,600 mm Extendable by 5,400 mm Axle spacing 1,360 mm Rear steering radius 2,300 mm Loading height with max. load 860 mm Total width 2,540 mm Suspension travel -55/+145 mm Technical description Gooseneck With bevelled corners at the front 45° and with rear bevel of approx. 760 mm x 10° 3 pairs of lashing rings (LC 5,000 daN) Hardwood flooring 30 mm thick Loading area in extendable version with rear slope of approx. 1,000 mm x 8° 5 pairs of lashing rings that can be folded outwards (LC 5,000 daN) 3 pairs of lashing rings that can be folded outwards (LC 10,000 daN) 1 pair of lashing rings lying in the front of the loading area (LC 10,000) Hardwood flooring approx. 48 mm thick, checkered plate above the axles Ramps Two-part steel ramps Fedpog Sk T Djfx Ag Djfw A pair of galvanized two-part steel ramps approx. 2750 +1400 mm x 800 mm with approx. 48 mm thick hardwood flooring Ramp with hydraulically foldable and retractable ramp parts, hydraulic lifting mechanism and hydraulically movable. Maximum load per pair 40,000 kg Tires 235/75 R 17.5 Brake system in accordance with EU regulations with EBS-E (4S3M) without connecting lines to the tractor unit Paintwork First-class, long-lasting corrosion protection of the standard shot-blasted welded frame guaranteed by 2-component zinc dust primer a high-quality 2-component (2K) top coat in a single color in RAL colors of your choice Rear section metallized and painted in RAL 9010 (pure white). Seat supports: JOST seat supports (mechanical) with 2-speed gearbox for 24t lifting load (50t test load) Steel construction made of high-strength fine grain steels. Steel qualities: Steel construction made of high-strength fine-grain steel S355J2+N/S355MC (yield strength 355MPa) S690QL/S700MC (yield strength 690MPa) Electrical system in accordance with EU regulations, lighting LED 24 Volt ASPÖCK-NORDIK (ASS3) ASPÖCK-UNIBOX on the connection panel at the front with sockets 24N, 24S & 15-pin. Connection in accordance with ISO. 24N IS0-1185 24S IS0-3731 15-pin IS0-12098 Accessories included: A galvanized steel front wall approx. 400 mm high. 2" kingpin 4 pieces of brake shoes with holder on the bulkhead. A holder for a rotating beacon at the rear of the trailer. SAF axles, two axles rigid, one axle with self-steering, air-sprung, with drum brake, with lifting/lowering function. The self-steering axle with electro-magnetic reversing lock can be activated via reverse gear or manually. Axle tool. Holder in the rear area of the gooseneck for aluminum loading ramps. Galvanized folding supports under the slope of the loading area. Mechanical locking of the loading area. A spare wheel with holder in front of the bulkhead. Yellow reflector tape in accordance with EU regulations on the side, on the extension and at the rear of the trailer. Yellow-red air couplings on the galvanized connection strip at the front. On the gooseneck and on the rear panel on the left and right there is a holder for the warning signs including a socket. A mud flap at the rear of the trailer. Manual and description On the gooseneck, plug-in aluminum side walls and rear wall approx. 2,440 x 400 mm (LX H). The rear galvanized plug-in stanchions are removable. Length of the body approx. 2,560 mm, +/- 46 kg 3 pairs of WADER container

Condition: new, axle configuration: > 3 axles, total length: 9,300 mm, total width: 2,540 mm, suspension: air, tire size: 245/70 R17.5, wheelbase: 1,360 mm, color: blue, Year of construction: 2023, Equipment: tail-lift, Colour: Blue Payload weight: 54,465 kg Main Features: Manufacturer: Faymonville Model: MAX 110-Z-4AA-9.30-U Chassis number: YAMT14XX4N0107629 Year: New and unused (2023) Weights/Loading Capacity: King-pin load: 23,000 kg Axle load: 12,000 kg (per axle) Total axle load: 48,000 kg Gross vehicle weight (GVW): 71,000 kg Empty weight: 16,535 kg Payload: 54,465 kg Axles: - Axle brand: BPW Ffedeuu Hcfepfx Ag Dsw - Hydraulic steering - Pneumatic suspension with raising/lowering valve - WABCO braking system - Tyres: 245/70 R17.5 Michelins (Load index 146/146 F) - 1st axle liftable Dimensions: Loading length: 9,300 mm Extensions: 6,500 + 6,800 mm Loading floor width: 2,540 mm Loading height: 900 mm Additional Equipment: - Double extendable loading platform - Container locks - Width outriggers + timber infills for width extension - Lashing rings - Double folding ramp set - Central lubrication - 1x spare wheel + holder - JOST landing gear - 24V electrical system - 2.0" king-pin - One galvanized steel headboard - Electrically driven hydraulic pump - Manual steering - Twist locks = Further Information = General Information: Year of manufacture: 2023 Axle Configuration: Tyre size: 245/70 R17.5 Suspension: Air suspension Rear axle 1: Twin tyres; lift axle; Max. axle load: 12,000 kg; Steerable; Axle brand: BPW; Tyre tread depth (left inside/outside, right inside/outside): 100% each Rear axle 2: Twin tyres; Max. axle load: 12,000 kg; Steerable; Tyre tread depth: 100% each Rear axle 3: Twin tyres; Max. axle load: 12,000 kg; Steerable; Tyre tread depth: 100% each Rear axle 4: Twin tyres; Max. axle load: 12,000 kg; Steerable; Tyre tread depth: 100% each Weights: Unladen weight: 16,535 kg Payload: 54,465 kg Gross vehicle weight: 71,000 kg Functional: Loading height: 900 mm (manufacturer’s specification; previously given as 65535 cm is a clear data error) Extendable body: Yes Condition: General condition: Very good Technical condition: Very good Optical condition: Very good Financial Information: Price: On request Further Information: Please contact Stefan Schaapveld for further details.

Condition: new, empty load weight: 15,550 kg, maximum load weight: 47,450 kg, overall weight: 63,000 kg, axle configuration: 3 axles, loading space length: 8,800 mm, loading space width: 2,540 mm, loading space height: 860 mm, suspension: air, tire size: 235/75 R 17,5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,700 mm -Rear gooseneck with bevel approx. 1,000 mm x 10° Loading area: -Loading area in extendable design, length approx. 8,800 mm, with bevel at the rear approx. 500 mm x 10° -One recess protruding into the loading surface and into the chamfer to accommodate the excavator dipper arm -Pneumatic locking with conical locking pins and reinforced locking positions -Hardwood covering on the bevel of the loading area Ramps: -1 Pair of two-part steel ramps with a length of approx. 4,350 mm and a width of approx. 900 mm -Ramps with hardwood decking -Hydraulically folding ramp tips -Ramps can be moved individually hydraulically by approx. 235 mm outwards and approx. 215 mm inwards -Square climbing ledges 20 x 30 mm, approx. every 200 mm on the outer frame of the ramp Axles and suspension: -BPW axles and suspension, 1st axle with preload steering, all other axles with forced hydromechanical steering -Technical axle load: 12,000 kg -1st axle with electromagnetic reverse lock via reverse gear and can be activated manually Fsdpfx Agsk Aht Uj Djfw -Air suspension with lifting and lowering valve -235/75 R 17.5 twin tires -TPMS tire monitoring system in accordance with ECE R141 -TPMS tire monitoring sensors mounted in all wheels including spare wheels Accessories included: -steel front wall, pluggable, approx. 400 mm high -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Parking position on the gooseneck for the warning signs when not in use -1 Spare wheel -On the gooseneck 1 pair of plug-in ALU side panels, approx. 400 mm high, anodized -One plug-in ALU rear panel on the gooseneck, approx. 400 mm high, anodized -Approx. 40 mm thick hardwood covering over the gooseneck, checker plate covering over the kingpin -2" kingpin -Guide plate from the gooseneck for the saddle plate, approx. 500 mm wide -4 wheel chocks -Mechanical seat posts with 2-speed gearbox and crank -JOST module B - static test load = 50,000 kg -1 Intermediate table, approx. 300 mm wide -Widenings (galvanized) extendable by approx. 230 mm per side -Wheel recesses with square climbing rails -ALU covers for the wheel recesses -1 pair of mechanical rear supports -Steering can be operated from the front and rear by cable remote control, with tracking control of the axles -1st axle with automatic lift axle function -Central lubrication system with 1 pump, BEKAMAX brand -Radio remote control for operating the self-steering, in addition to the cable remote control, with 2 indicator lights on the receiver as toe-in control -Wabco Smart Board System -4 warning signs, approx. 423 x 423 mm, extendable by approx. 400 mm, incl. 2 position lights and brackets for rotating beacon

Condition: new, functionality: fully functional, Year of construction: 2024, power: 125 kW (169.95 HP), load capacity: 230 kg, mast type: telescopic, lifting height: 25,600 mm, lifting power: 230 kg/m, platform length: 1,400 mm, platform width: 700 mm, overall weight: 3,500 kg, empty load weight: 3,300 kg, transport length: 6,990 mm, transport width: 2,220 mm, transport height: 2,900 mm, construction height: 3,000 mm, fuel type: diesel, fuel consumption per hour: 8 l/h, fuel tank capacity: 80 l, tire size: 225/75 R16, tire condition: 100 %, wheelbase: 2,900 mm, ground clearance: 220 mm, color: white, Equipment: ABS, UVV, soot filter, tilting carriage, === MAIN SPECIFICATIONS === Year of manufacture: 2024 Operating hours: – (on request) Max. working height: 27.6 m Max. horizontal outreach: 17.0 m Platform capacity: 230 kg Truck type: Mercedes-Benz Fedsxdawhjpfx Ag Dofw Number of axles: 2 Drive type: 4x2 Transmission: Automatic Cab type: Single Engine power: approx. 125 kW (170 HP) Fuel type: Diesel Platform dimensions (L x W): 1,400 x 700 mm Platform rotation: Yes (2 × 90°) Boom type: Telescopic (4-section aluminum) Stabilisers: Yes (fully hydraulic, individually controlled) CE certification: Yes (EEC type approval) Total vehicle weight: 3,500 kg === HIGHLIGHTS === Carefully selected from reliable sources with verifiable history CE certification and full documentation included Automatic positioning system and “Home Function” standard Compact design with impressive height and outreach === CONDITION === Brand-new condition – unused 2024 unit, fully inspected and tested. Color: white. Inspection possible upon request. === LOCATION & DELIVERY === Located in Sittard, Netherlands. Worldwide delivery available. Price: €189.000 (EXW / excl. VAT) The Palfinger P 280 B (2024) is a state-of-the-art truck-mounted platform on a Mercedes-Benz chassis, offering an impressive 27.6 m working height and 17 m outreach. With its fully telescopic aluminum boom, automatic positioning system, and Home Function, this model delivers outstanding performance and user comfort. Weighing only 3,500 kg and featuring a 230 kg basket load, it is ideal for maintenance, installation, and rental operations. Fully CE-certified and ready for immediate use. === DELIVERY === Crane loading available on request for smooth transport. Flexible international delivery options. All logistics handled professionally by the Collé Rental & Sales logistics team