Plate Shear - Hydraulic
EHT TSS 4-31

Year of construction

1985

Condition

Used

Location

Ahaus

Basic data

Machine type:: Plate Shear - Hydraulic

Manufacturer:: EHT

Model:: TSS 4-31

Year of construction:: 1985

Condition:: used

Price & Location

Location:: Ahaus

Call

Details about the offer

Listing ID:: A19924945

Reference number:: 1125-9325371

Update:: 01.11.2025

Description

sheet width 3100 mm
plate thickness 4.0 mm
thickness at "Niro-steel" 2.5 mm
cutting angle adjustment 1.0 °
back stop - adjustable 10 - 1000 mm
adjustment speed 180 mm/s
down holder 21 Stück
Pgsdjxab Tvspfx Akiou
strokes per minute 18 - 31
oil volume 160 L
Control ELGO P8511
column arm 200 mm
distance between columns 3050 mm
0 max. 300 bar
voltage 400 V
main drive 9.0 kW
weight of the machine ca. 4800 kg.
dimensions of the machine ca. 3660 x 2070 x 2140 mm
from a maintenance workshop

Equipment:
- electro-hydraulic sheet metal shear "swing cut"
- machine frame = all-steel welded construction
- ELGO NC control model P8511, control panel at the front left
* for positioning the electro-motoric rear stop
* target/actual position value input possible
* adjustment by three-phase motor via toothed belt
- support table with ball rollers
* there are recessed grips between the table plates
- front finger guard
- hydraulically acting sheet metal hold-down device
- 1x freely movable foot switch
- emergency stop button at the front
- movable scrap switch
- original operating instructions + circuit diagram

Special accessories included:
- EHT pneumatic sheet metal holding device for thin sheet metal cuts
- 1x EHT extra long side stop 3.000 mm with mm scale & support foot
- 1x EHT extra long support arm with 3.000 mm with scale & Support foot
- EHT additional support arms with mm scale

Seller

Registered since: 2011

704 listings online

Call

Send inquiry

Telephone & Fax

+49 5939 ... show

Fax:

These listings may also fit your interest.

Listing

Germany

1,293 km

Sheet Metal Shear
EHTTSS 4-31

Call

Year of construction: 1987, condition: ready for operation (used), An EHT hydraulic guillotine shear refurbished in 2023 is available. Cutting length: 3000mm, max. sheet thickness steel/VA: 4mm/2mm, backgauge: 10mm-1000mm, adjustment speed: 180mm/s, stroke rate: 18-31 strokes/min, oil volume: 160l. Machine dimensions X/Y/Z: approx. 3700mm/2100mm/2150mm, weight: approx. 4800kg, operating hours: 44024h. The cylinders, blades and hoses were overhauled in 2023. On-site inspection is possible. Podowrhwujpfx Akiegu

See details

Listing

Machining Center - Vertical PINNACLE LV 117 / TNC 640

Dreieich

1,224 km

Machining Center - Vertical
PINNACLELV 117 / TNC 640

Call

Condition: used, Year of construction: 2015, x-travel 1140 mm y-travel 710 mm z-travel 610 mm CNC-control Heidenhain TNC640 table-size 1300 x 700 mm max. table load 1000 kg spindle taper SK 40 spindle turning speed range 10.000 U/min feed stepless max. 10.000 mm/min rapid traverse 24/24/24 m/min tool change unit 30 Pos. coolant IKZ 40 bar drive capacity - spindle motor 7,5 / 11 kW voltage 400 V total power requirement 25 kVA weight of the machine ca. 9,0 t dimensions of the machine ca. 3,25 x 3,08 x 3,00 m chip conveyor 4,30 x 0,80 x 1,60 m band filter unit 2,00 x 1,00 x 1,30 m coolant tank 1,30 x 1,00 x 0,60 m - Serial No.: 4P11152J1 - Machine ON: 23,320 h - Spindle ON: 5,042 h - Control: HEIDENHAIN TNC 640 - TSC 40 bar incl. 600 liter coolant tank with paper band filter unit - Y-Axis with 4 liear guide rails! - Chip conveyor - X- and Z-Axis with 6 roller supports for each axis! Pgodpfx Akjxx A Eweisu

See details

Listing

Plate Shear - Hydraulic HERA HSS III / 3100 x 2,0

Niederlangen

1,037 km

Plate Shear - Hydraulic
HERAHSS III / 3100 x 2,0

Call

Condition: used, Year of construction: 1978, sheet width 3100 mm plate thickness 2 mm rear stop 1000 mm cutting angle 1°06 ° no. of strokes 45 Hub/min total power requirement 3,0 kW dimensions of the machine ca. 3600 x 2200 x 1600 mm weight 4500 kg Equipment: - Electric motorized backgauge - With digital ELGO position display - Manual cutting gap adjustment - 1x side stop with mm scale - 2x support arms - 1x freely movable double foot switch - Front finger guard Psdpfx Aouagxpokijgu Special accessories included: - Pneumatic sheet metal holding device for thin sheet metal cuts

See details

Listing

Folding Machine FALKEN // ERBEND UFA 1015

Ahaus

1,037 km

Folding Machine
FALKEN // ERBENDUFA 1015

Call

Condition: as good as new (ex-display), Year of construction: 2023, sheet width 1050 mm plate thickness 1.50 mm daylight opening 100 mm bending angle max. 135 ° height OW 100 mm total power requirement manuell weight of the machine ca. 330 kg. dimensions of the machine ca. 1600 x 900 x 1450 mm Pgedpfx Asxaa T Uokiou Exhibition machine from 2023 only 2x machines in stock special price on request Features: - robust, manual folding machine - split upper, lower and rear tool * Height of upper tool = 100 mm * Pitch 100/100/100/100/100/100/100/100/100/70/60/50/40/30/100 * Left right with horn tool - Upper tool with quick-change system - Quick foot clamping - Angle fence - lockable - Manual back gauge 500 mm - Machine can be moved (rollers) - Accessory box - rear * Pictures show identical machine (UFA 1212)

See details

Listing

Machining center Doosan NM510 Vertical Machining Centre

Ireland

166 km

Machining center
DoosanNM510 Vertical Machining Centre

€22,900

EXW ONO plus VAT

Call

Condition: excellent (used), Year of construction: 2008, functionality: fully functional, type of input current: three-phase, travel distance X-axis: 1,020 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, workpiece weight (max.): 800 kg, number of slots in tool magazine: 30, controller manufacturer: Fanuc, total height: 2,700 mm, total length: 4,080 mm, total width: 2,400 mm, overall weight: 7,000 kg, table length: 1,200 mm, table width: 510 mm, controller model: Oi-MC, coolant supply: 15 bar, spindle motor power: 15,000 W, number of spindles: 1, rapid traverse Z-axis: 30 m/min, rapid traverse X-axis: 36 m/min, rapid traverse Y-axis: 36 m/min, spindle nose: BT40, spindle speed (max.): 12,000 rpm, table load: 800 kg, Equipment: chip conveyor, rotational speed infinitely variable, Doosan NM510 Vertical Machining Centre Machine Type: 3 Axis Vertical Machining Centre Year: 2008 Control: Fanuc Series Oi-MC Condition: Very Good Includes Swarf Conveyor Chiller MCF20 Coolant Filter Autolube 6 x Tool Holders Notes Vice and clamping block in photos not included Technical Specifications Table Size: 1200 x 510mm Table Load: 800kg Travel (X-Axis): 1020mm Travel (Y-Axis): 510mm Travel (Z-Axis): 510mm Max Spindle Speed: 12,000rpm Spindle Power: 18.5/15/11kW Spindle Taper: BT 40 Rapid Traverse (X/Y/Z): 36/36/30m/min Tool Storage Capacity: 30 tools Tool Change Time (T-T/C-C): 1.7/3.5sec Machine Dimensions: 4080 x 2400 x 2700mm Pgjdpfev Iq Ezex Akiou Machine Weight: 7,000kg Notes: *Specifications are given in good faith but not guaranteed*

See details

Listing

Rödermark

1,235 km

Hydr. hole punch
MUBEAKLH 300/610

Call

Year of construction: 1998, condition: good (used), machine/vehicle number: 0159488169537, Offer 23293 Podopuy H Dspfx Akiogu Technical data: - Pressure capacity 300 KN - punches e.g. up to 30 mm Ø in steel 9 mm - or with special punching device up to 100 mm Ø in steel 2.5 mm - stroke infinitely variable 0 to 28 mm - stroke rate 26 to 36 1/min - throat 610 mm - Installation height 240 mm - Drive 400 V / 4 kW - Space requirement approx. W 750 x H 1650 x D 1350 mm - weight approx. 1300 kg - with: - foot switch - grain search device, - support table with foldable stops W 1100 x D 850mm - shifting distance of the stops from the center of the punch - width between Li and Re approx. 470 mm x D 510 mm

See details

Listing

Львів

2,249 km

Radial riveting machine RMU-12-C
ROMIOL

Call

Condition: new, Year of construction: 2025, Pneumatic radial riveting machine RMU-12-C is designed for forming caps in solid steel rivets d=2...12 mm and in tubular steel rivets d=4x1...14x1 mm. Technical data: 1. Diameter of solid steel rivets - 2...12 mm. 2. Diameter of tubular steel rivets - 4...14 mm. 3. Motion of riveting head - 20 mm. 4. Time of unriveting for one rivet - 1...10 sec. 5. Motor power - 0,75 kW. 6. Voltage - 220/380 V 50 Hz. 7. Working pressure - 3...6 Bar. 8. Weight - 100...120 kg. This riveting machine can be used for movable and immovable riveted connections. Pgjdpefvztuofx Akisu The cost of the riveting machine does not include the cost of punches and shipping costs.

See details

Listing

Band Saw Horizontal Band Saw Semi Automatic Fastech BMSY 360 DGH ECO

Mudersbach

1,141 km

Band Saw Horizontal Band Saw Semi Automatic
FastechBMSY 360 DGH ECO

€15,500

Fixed price plus VAT

Call

Condition: new, Fastech Horizontal Bandsaw, Semi-Automatic, BMSY 360 DGH ECO Round Cutting Capacity mm: 360 Flat Cutting Capacity mm: 510 x 360 Square Cutting Capacity mm: 360 +30° Round Cutting Capacity mm: 360 +30° Flat Cutting Capacity mm: 440 x 360 +30° Square Cutting Capacity mm: 360 +45° Round Cutting Capacity mm: 360 Pgjdeg Ekttjpfx Akiju +45° Flat Cutting Capacity mm: 390 x 360 +45° Square Cutting Capacity mm: 360 +60° Round Cutting Capacity mm: 200 +60° Flat Cutting Capacity mm: 200 x 360 +60° Square Cutting Capacity mm: 200 -30° Round Cutting Capacity mm: 360 -30° Flat Cutting Capacity mm: 440 x 360 -30° Square Cutting Capacity mm: 360 -45° Round Cutting Capacity mm: 360 -45° Flat Cutting Capacity mm: 390 x 360 -45° Square Cutting Capacity mm: 360 -60° Round Cutting Capacity mm: 260 -60° Flat Cutting Capacity mm: 260 x 360 -60° Square Cutting Capacity mm: 260 Motor Power, Main Drive kW 3 Hydraulic Pump Power kW 0.37 Motor Power, Coolant Pump kW 0.12 Band Speed, stepless: m/min 20 - 100 Saw Band Dimensions mm: 4800 x 34 x 1.1 Height of Work Surface mm: 860 Weight kg: 1450 Length / Depth / Height mm: 2650 / 1210 / 1870 Double Miter Saw Stepless Band Speed Hydraulic Vise High-Performance Gearbox Hydromechanical Saw Band Tensioning Saw Band Brush Digital Display for Miter Angle

See details

Listing

Korschenbroich

1,038 km

Bolster plate
KRUPSA 3,5 -2

€4,800

Fixed price plus VAT

Call

Condition: used, Year of construction: 1988, plate width 2000 mm plate depth 3500 mm plate height 270 mm weight 5,5 t +++++ Please note: The machine is dismantled and ready for loading. It is not possible to show it under power or make a video. Our offer includes already the best pictures. So we don’t have and won’t send additional pictures. Pjdpsiiii Sjfx Akiogu +++++

See details

Listing

Vertical machining center HERMLE B 300 V

Aach

1,354 km

Vertical machining center
HERMLEB 300 V

Call

Condition: reconditioned (used), Year of construction: 2010, functionality: fully functional, CNC Vertical Machining Center HERMLE B 300 V With Heidenhain iTNC 530 path control Year of manufacture: 12/2010 Travel ranges: X 800, Y 600, Z 500 Spindle speed range: 20 – 15,000 rpm, stepless With the following accessories: Pgedpfezf Ik Ejx Akiou Fixed angular table, 1000 mm x 560 mm clamping surface Vertical tool changer with 30 magazine positions (SK 40) IKZ 40 bar Chip conveyor Coolant system Manual cabinet door, manual cabinet roof Polycarbonate safety screens Electronic thermal compensation iTNC 530 Electric hand control module HR 410 3D measuring probe Renishaw Control cabinet cooling unit (RITTAL) Spindle oil cooler 4 adjustable machine feet Operating manuals

See details

Advertise here

Plate Shear - HydraulicEHT TSS 4-31

Basic data

Price & Location

Details about the offer

Description

Seller

Send inquiry

Telephone & Fax

Plate Shear - Hydraulic
EHT TSS 4-31