Eccentric press - Single column press

DIGEP SD 100 (2282)

Condition: good (used), Year of construction: 1980, turning diameter over bed slide: 1,040 mm, turning diameter over top slide: 710 mm, turning length: 2,000 mm, bed width: 600 mm, Optional chuck 1200 mm 2 Axis RSF Digital read out Conical turning attachment Spindle bore 130 mm Central lubrication DBC Turning Length: 2000mm Swing over bed Ø: 1040mm Swing over cross slide Ø:710mm Swing in the gap Ø: 1780mm Gap length: 1000mm Spindle bore: 130mm Bed width: 600mm Gjdpsx Tgr Tjfx Amyeug Tailstock spindle Ø: 130Ø Stroke pinole: 300mm Spindle taper: 6Mk Power: 22kW Speeds / ranges: 600Rpm Feed rate X-Axis: 4000mm/min. Feed rate Z-Axis: 4000mm/min. Length: 6000mm Width: 2100mm Height: 2100mm Weight: 8300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Year of construction: 1998, thread length: 65 mm, Treading machine ORT Italia - RT 10 MACH-ID 9322 Make: ORT Italia Type: RT 10 Control: Siemens SIMATEC Gedpfox H Rmujx Amyjug Year: 1998 Maximum pressure: 10T Max. workpiece: 30Ø Min. workpiece: 2Ø Min. Threading lenght:2mm Max. Threading length:65mm Pitch / lead: 30mm Shaft Ø: 85 - 135mm Length: 1600mm Width: 1400mm Height: 1800mm Weight: 2300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: new, maximum load weight: 67,200 kg, overall weight: 85,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including immediately and short-term available vehicles, on our website. Excerpts from the equipment. Full specifications available upon request. GOOSENECK * Gooseneck in SNT design to optimize load floor length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractors: 6 x 2, 6 x 4, and short 8 x 4 * Detachable steel front wall, approx. 400 mm high * 3 kW electro-hydraulic power unit for controlling hydraulic functions, except for hydraulic winches * Outer beams of the gooseneck with mounting holes for bolt-on lashing rings * 2 pairs of screw-in lashing rings included (LC 5,000 daN) * 1 pair of flat lashing rings at the rear of the gooseneck (LC 10,000 daN) * 1 pair of plug-in aluminum side boards, approx. 400 mm high, anodized * 1 plug-in aluminum rear board, approx. 400 mm high, anodized * Approx. 40 mm thick hardwood flooring above gooseneck, checker plate flooring above kingpin * 3.5 inch kingpin * Gooseneck guide plate for the fifth wheel plate, approx. 500 mm wide * Round NATO socket at the front connection strip (Maeler & Kaege VG 96 917) * In addition to the electro-hydraulic unit, a truck hydraulic connection with flow regulator, including bracket for hanging supply lines (Faymonville couplers) * 2 pairs of stake pockets recessed in the gooseneck, for plug-in stakes approx. 100 x 50 mm LOAD FLOOR * Extendable load floor, approx. 11,000 mm long, with rear bevel approx. 500 mm x 10° * Pneumatic locking with conical locking bolts and reinforced locking positions; supply lines are protected inside the extendable beams and automatically adjust to the respective deck length * BPW axles and suspension, 1st axle steered, 2nd axle fixed, all other axles hydro-mechanically forced steered * 1st axle with electro-magnetic reverse lock via reverse gear and manual activation * Axle load capacity: 12,000 kg each * Air suspension with lift and lower valve * 235/75 R 17.5 3PMSF twin tires * Mechanical landing gears with 2-speed gearbox and crank. JOST Modul B – static test load = approx. 50,000 kg * Continuous and, between axles, interrupted approx. 50 mm thick hardwood floor on load deck (increases coefficient of friction) * Slotted holes for attachable and repositionable bridging elements: – at the fixed part behind the gooseneck – on the front of the load floor * 1 sliding intermediate table, approx. 500 mm wide, for the sliding tube with large cross-section, checker plate flooring, front and rear with slotted holes for attachable and repositionable bridging elements * 1 pair of recessed flat lashing rings in the front fixed part of the load floor (LC 10,000 daN) * 9 pairs of recessed lashing rings, foldable outward, in the load floor perimeter frame (LC 10,000 daN) Gusdjrgzv Nspfx Amysg * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking control, no installation required in the tractor * 1st axle with automatic lift axle function and start-up assist according to EU Regulation 2021/535 * Under the gooseneck and at the rear cross member, left and right, a 7-pin socket each with holder for warning signs * Factory-applied sand coating on the perimeter frame of the load floor as well as the checker plates and the transition area between load decks

Condition: used, Year of construction: 2010, operating hours: 11,780 h, Equipment: ABS, all wheel drive, Volvo EXCAVATOR EW140C air conditioning Gujdpsyltr Aefx Amyjg 16,850 kg 91 kW Top condition

Condition: ready for operation (used), Year of construction: 1980, Gleason Hypoid cutter Sharpener 13A -1 pcs Milling diameter 89-500 mm Grinding wheel dimensions 305x19x102 mm Feed 0,05-0,18 mm Gusdpfjr Elpvsx Amyjg Grinding wheel drive motor - 1800 rpm (60 Hz) - 1500 rpm (50 Hz) Floor space 1240x2310 mm Height 1422 mm Machine weight 4083 kg Gleason 19 revacicle cutter checking machine - 1 pcs

Condition: good (used), Year of construction: 1995, roller (top) diameter: 330 mm, sheet thickness (max.): 23 mm, Manufacturer: IMCAR Type: SIHR Year of manufacture: 1995 Extended end for profile bending rolls (Pipe & T-Angle) Central lubrication Digital readout position side rolls Fully hydraulic machine Hydraulic drop end Hardened rolls Specifications Metric US Standard Roll width: 3100 mm Sheet thickness at 3 x top roll Ø: 18 mm Sheet thickness at 5 x top roll Ø: 23 mm Sheet thickness for initial bending: 20 mm Top roll Ø: 330 mm Side roll Ø: 310 mm Number of rolls: 3 Bending speed: 0 - 5 Side roll adjustment: 200 mm/min. Number of driven rolls: 2 Power: 15 kW Dimensions (estimated) Length: 5250 mm Width: 1700 mm Height: 1700 mm Gujdpswpku Djfx Amyjg Weight: 11900 kg Please note: The information on this page has been provided to the best of our knowledge, and wherever possible, from the manufacturer. The information is given in good faith, but accuracy cannot be guaranteed. Accordingly, it does not constitute representation or contractual terms. We recommend you check all critical details.

Condition: excellent (used), Tacchella Macchine grinding machine, type 40LR, in very good condition. Specifications: Longitudinal travel, X-axis: 400 mm Cross travel, Y-axis: 250 mm Clearance between worktable and spindle axis: 375 mm Guodpfoivg E Hex Amyeg Wheel speed: 3000/6000 rpm Wheel dimension: 150x20 mm Weight: 800 kg

Condition: used, 72″ x .187″ x 50,000Lb Paxson Loop Slitting Line Make: Paxson Material Width: 12″ – 72″ (Uncoiler 60″) Material Width: .010″ – .187″ Coil Weight: 50,000Lb Coil ID: 20″ – 24″ Coil OD: 72″ Speed: 500 /1000 fpm Direction: Right to Left Material Strength: 40,000 yield / 50,000 psi shear Material: CR, HR, Galvanized Gedpjihf Ufsfx Amyjug Entry Transfer Cart Entry Coil Car Mandrel Uncoiler Powered Hold-Down Roll Powered Expansion Sliding Base Hydraulic Peeling Table Driven Pinch Rolls

Condition: used, Year of construction: 1987, faceplate diameter 3600 mm swing diameter 4500 mm turning height 1850 mm Gsdsyz Db Uopfx Amyeug turning speed range 0,6- 50 U/min weight of the machine ca. 72 t verticale turning machine double coloumn - digital scale - double coloumn - 2x ram - movable cross slide - extra toolholder (four station) on the side of facing plate

Condition: used, Year of construction: 1984, functionality: fully functional, travel distance X-axis: 1,800 mm, travel distance Y-axis: 1,500 mm, travel distance Z-axis: 2,000 mm, table load: 5,000 kg, spindle diameter: 110 mm, total height: 3,800 mm, total length: 5,000 mm, total width: 3,000 mm, table length: 1,520 mm, table width: 1,225 mm, feed length X-axis: 1,800 mm, feed length Y-axis: 1,500 mm, feed length Z-axis: 2,000 mm, Tool holder SK50, Heidenhain control, machine is ready for collection and immediately operational. Godpfsxga Tnsx Amyeug