Overhead crane ± 10.500 mm x 12.500 kg

Demag ZKKE

Condition: like new (used), Year of construction: 2010, machine/vehicle number: 1099883, operating hours: 100 h, Demag end carriage pair Cpjdpfjw H S Avsx Afnju End carriage DRS315 Hoist unit EZ DR20 Trolley gauge 2240 mm Reeving 4/1 The crane shows virtually no wear, very little use in a machine construction factory. Dismantled in July 25 and stored dry. Complete with documentation and HBC Spectrum radio remote control. All motions with frequency inverter! Modifications can be offered separately.

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. Csdsfg E Hpepfx Afnopu • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Year of construction: 2007, condition: good (used), functionality: fully functional, machine/vehicle number: 12428 B500-851, Overheadcrane ± 14.170 mm x 25.000 kg Cedpfov Ip Afjx Afnepu

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 13354 B521 850, Overheadcrane ± 10.500 mm x 12.500 kg Cedjv Ip Dispfx Afnopu

Year of construction: 2011, condition: excellent (used), This is a complete plant for house construction. Prices are listed with each item. Consisting of the following individual elements (see attached document as well): Photos will follow, they are already included in the attached document. Table 1 (Positioning and clamping of the frame structure) €34,500 - Elevating longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity Table 2 (Applying the first sheathing and fastening) €25,300 - Longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity Intermediate conveyor 3 m long €4,600 (Parking station for multifunctional bridge) - Longitudinal conveyor with 3 hinge conveyors Table 3 (Applying the second sheathing, fastening and turning the element onto the next table) €35,650 - Longitudinal conveyor with 3 hinge conveyors and sheathing - Pneumatic cross clamping - Connections for compressed air and electricity - Hydraulic turning device Table 4 (Electrical installation and insulation) €34,500 - Cross conveyor with rollers and sheathing - Table traverse drive - Connections for compressed air and electricity - Hydraulic turning device Table 5 (Applying the first sheathing and fastening the second side) €32,775 - Longitudinal conveyor with 3 hinge conveyors - Cross conveyor with rollers - Pneumatic cross clamping - Connections for compressed air and electricity Codpfju D Amgsx Afnjpu Intermediate conveyor 3 m long €4,600 (Parking station for multifunctional bridge) - Longitudinal conveyor with 3 hinge conveyors Table 6 (Applying the second sheathing and fastening) €28,750 - Longitudinal conveyor with 3 hinge conveyors - Pneumatic cross clamping - Connections for compressed air and electricity Table 7 (Erection and distribution table) €29,900 - Longitudinal conveyor with 3 hinge conveyors - Hydraulic tilting unit - Table traverse mechanism - Upper guide for holding the walls vertically Manual surface gantry with vacuum lifter on Table 2 €13,800 (Applying the first layer of sheathing) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 3 €13,800 (Applying the second layer of sheathing) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 5 €13,800 (Applying the first layer of sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Manual surface gantry with vacuum lifter on Table 6 €13,800 (Applying the second layer of sheathing on the second side) - Load capacity 85 kg with Schmalz vacuum unit - Steel substructure with low-friction rails - Travel range 12 x 5 m Wall storage 1: 12 m long x 24 tracks €11,500 Wall storage 2: 12 m long x 20 tracks Vacuum lifter with column slewing crane €9,200 1 cross beam 2 t Abus €20,125 1 cross beam 2 t

Year of construction: 1998, condition: good (used), functionality: fully functional, machine/vehicle number: 12157 B51 864, Overheadcrane ± 10.500 mm x 16.000 kg Cpedov Ip E Hjpfx Afnsu

Condition: used, Year of construction: 1997, travel distance X-axis: 3,708 mm, travel distance Y-axis: 1,208 mm, travel distance Z-axis: 1,002 mm, feed length X-axis: 5,000 mm, feed length Y-axis: 5,000 mm, feed length Z-axis: 5,000 mm, rapid traverse X-axis: 15 m/min, rapid traverse Y-axis: 15 m/min, rapid traverse Z-axis: 15 m/min, spindle speed (max.): 3,000 rpm, spindle speed (min.): 35 rpm, CNC Bed-Type Milling Machine – Universal ZAYER 20 KF 4000 Year of manufacture: 1997 CNC control: HEIDENHAIN TNC 426/430 Cpodpowtpfpefx Afnju Technical specifications: X travel: 3708 mm Y travel: 1208 mm Z travel: 1002 mm Table size: 4000 x 1000 mm Tool holder: SK 50 Spindle speeds: 35–3000 rpm Spindle motor: 22 kW Feed range: 6–5000 mm/min Rapid traverse: 15 m/min Machine weight: approx. 19.5 t ADDITIONAL INFORMATION Electronic handwheel Automatically swivelling milling head vertical/horizontal +/-120° (stepless) Milling head automatically swivelling in the rear axis / 90° rotation Coolant system The machine can be inspected under power. Delivery time: immediately Sale from location Westerkappeln Dismantling, loading available on request.

Year of construction: 2021, condition: like new (used), functionality: fully functional, machine/vehicle number: 3815407, WEIGHT 8000KG FEM ISO 1Am M4 KW 2.4/15.5 ( 50 Hz) MAXIMUM CAPACITY 16 TON Cpsdpfx Afet Nhqyoneu

Condition: new, Year of construction: 2025, Blast Container High Cube Basic with Sweeping Floor Shovel Hopper for approx. 4 pressure vessel fillings + extra blasting vessel filling, enabling extended blasting time without refilling. Type SC.20FHC.5800 Basic Standard Equipment, ready for operation (just add abrasive and connect power and compressed air): 1x Control cabinet with emergency stop, Siemens Logo controller 1x Pressure blasting vessel 1x Pressure regulator and water separator 1x Blasting hose DN 25 with 8mm blasting nozzle 1x Remote control with dead man's switch 1x Abrasive inlet box/hopper 1x Abrasive media sieve + collection container for coarse particles 1x Airwash separator for blast dust extraction (dust reduction during blasting) 1x Filter unit with pre-chamber separator 1x Suction wall with louvre-type impact separator 1x 4mm rubber wall lining with fabric insert 1x Tread plate floor 3/5 1x LED lighting 1x Emergency lighting, door-end switch, emergency stop 1x Breathing air filter 1x Blasting helmet 1x Blasting gloves 1x Coverall/suit Options: - Side Door Open: blast container can be fully opened from the side for easy forklift loading - Container widening - Container extension - Crane roof hatch - 500kg crane runway - C-profile rail for powder coating - Blasting trolley - Filter with big bag - HEPA secondary filter for hazardous dust, e.g. when blasting stainless steel Cedpjw Ivk Tsfx Afnopu - Stainless steel tread plate floor for stainless steel blasting - Aluminum tread plate floor and much more upon request!

Condition: good (used), functionality: fully functional, Year of construction: 1991, sheet thickness steel (max.): 16 mm, cutting length (max.): 6,000 mm, HYDRAULIC SHEAR LVD MVSB 62/16 Serial number 18478 Yom 06/1991 TECHNICAL SPECIFICATIONS Max. sheet thickness St45 16 mm Cutting length 6200mm Distance between uprights 6400mm Gap 60mm Range back gauge 1000mm Min. cutting angle 0.5 ° Max. cutting angle 2.5° Min. number of strokes/min. 6 Max. number of strokes/min 25 Min. blade clearance 0.05 mm Cjdpfxjumhm Ao Afnopu Max. blade clearance 1.6mm Motor power 30kW Approx weight 35000 Kg LxWxH 7100x2400x3000mm Accessories included; ELGO P85 “GO-TO” for back gauge Electrical adjustment of back gauge 1000mm 1 x Front support 2mtr, one with 90° square arm front support L2000mm Foot pedal Ball bearings on table Inclinable back gauge with manual hydraulic pump