Tool cutter

DECKEL P 1

Condition: new, Year of construction: 2026, UNIBOHRFIX 100 H Fully automatic drilling machine, measuring length 6000mm Item No. 6020 Bjdpfxefu Itbs Ammsdc With the fully automatic drilling machine UniBohrFix 100, your material is positioned on the X-axis at the desired position, clamped and drilled. All you have to do is press the start button. Round tubes, rectangular tubes and angle profiles, as well as flat and solid materials, can be conveniently pneumatically clamped in the horizontal gripper of the positioning system. After simply entering the X values ​​and calling up a program that has already been written, the machine works completely independently. The Y-axis can be adjusted by the operator using a handwheel with a digital display. Advantages • A sequence of holes is automatically executed at precise intervals. • Potential operator errors are drastically reduced. • Programming takes just a few minutes. • Very good value for money. • Significant reduction in labor force Fully automatic execution Measuring length: 6,000 mm Total length: 13,500mm NC 1-axis control Pneumatic vice (span 200 mm) Minimum quantity spray unit with holder and spray nozzle Drill: Unimax 3T AV (for technical data see data sheet) anti-rotation device motorized height adjustment tapping device NC positioning system PD 200p Feed force 200 kg Positioning according to absolute and incremental dimensions possible Carriage with DC servo motor and encoder Trolley with 12 ball bearings Pneumatic stop clamping with high holding power Steel guide rail with precision toothed rack Steel carrier profile to protect against dirt Infeed and outfeed material roller conveyor RD-200/4 Length: 6,000 mm / 7,000 mm / load capacity 200 kg/m / rollers adjustable in height / mounting bracket / roller width 407 mm / insert plates / struts / roller diameter 50 mm / steel rollers

Condition: excellent (used), Surface of the base plate 880 x 700 mm Distance from spindle center to stand min./max. 220 / 620 mm Drill spindle: 13 mm passage Inner cone MK 3 Stroke 150 mm Spindle speeds 25 - 2560 rpm. Spindle feeds 0.06 - 0.12 - 0.25 mm/rev Motor power (1500/3000 rpm) 1.2 / 1.5 HP Bdedpfx Aouigzpsmmjc

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: up to round tube 48 x 3,0 mm Bsdpfx Ajd S Uf Semmjdc flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: used, Technical specifications: X-axis travel: 700 mm Spindle speed: up to 1500 rpm Feed rate: 12 - 1000 mm/min Bdodpfxsxtnn To Ammoc Table size: 1100 x 250 mm Swiveling head: yes Dimensions, approx.: 1750 x 1600 x 1850 mm Weight, approx.: 1900 kg

Condition: used, operating hours: 1,980 h, power: 103 kW (140.04 HP), gearing type: mechanical, fuel type: diesel, first registration: 05/2020, color: green, overall weight: 10,450 kg, mileage: 1,980 km, empty load weight: 6,900 kg, maximum load weight: 3,550 kg, suspension: other, number of seats: 2, Equipment: air conditioning, all wheel drive, cabin, Front hydraulics, 1st hand, radio, power steering, HU/AU new, AutoPowr transmission Diesel hydrostatic power steering All-wheel drive First registration 25.05.2020 103 kW 4,525 cm³ 1,980 operating hours Industrial front loader Front PTO Front hydraulics device Autotrac 360° illumination Cabin Cab suspension Suspended front axle Air conditioning Heating Command Arm Display in the A-pillar Radio 2-seater cup holder 40 km/h approval 1st hand Aluminum rims Empty weight 6,900 kg permissible weight 10,450 kg Hand Alloy rims Unladen weight 6,900 kg Gross vehicle weight 10,450 kg FOR US THE CONDITION AND THE FEEL OF THE CONSTRUCTION ARE DECISIVE, THE PRICE IS SECOND. If you have any further questions, please do not hesitate to contact Mr. Faller on the following number. //*EXCHANGE, DEPOSIT OR RENTAL OF YOUR VEHICLE, AS WELL AS FINANCING POSSIBLE! All information without guarantee* You can find further offers on our homepage: The description and data given do not constitute a guarantee and are not binding. The contract of sale concluded at the dealership when the vehicle is purchased is binding. Subject to errors and prior sale! Bdjdpfevic Drex Ammoc

Condition: new, empty load weight: 12,900 kg, maximum load weight: 34,100 kg, overall weight: 47,000 kg, axle configuration: 2 axles, loading space length: 6,850 mm, loading space width: 2,540 mm, loading space height: 350 mm, suspension: other, tire size: 245/70 R 17,5, color: grey, operation weight: 12,900 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered hydraulically and removed -Technical fifth wheel load: 23,000 kg -For tractor units: 4 x 2, 6 x 2 and 6 x 4 Loading area: -Low bed with external supports in extendable "SUPER LOW" design, length approx. 6,850 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking Rear chassis: -Rear chassis with closed external frame, checker plate covering and continuous prism excavator trough approx. 1,250/700 x 505 mm, open at the rear -2 pairs of lashing rings that can be folded outwards Bdjdpjhlz R Sjfx Ammsc -1 pair of lashing rings lying in the trough -2 pairs of stake pockets for plug-in stakes 100 x 50 mm in the outer frame Pendulum axle and tires: -"PENDEL-AXLE", all axles hydromechanically forced steered -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint, painted in a single color in "FAY-Gray-34-0260" -Technical axle load: 12,000 kg -Hydraulic axle compensation -Tires 245/70 R 17.5 -TPMS tire pressure monitoring system in accordance with ECE R 141 Accessories: -Preparation for screw-on container positioning for 1x 20ft or 1x40ft container on the outer supports -2" kingpins -A galvanized steel front wall approx. 400 mm high -One spare wheel -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering from the front and rear can be operated using a cable remote control via push buttons, with alignment control of the axles -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Electro-hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and at the rear -European reflector signs (red-yellow) on the rear of the trailer -One holder for the warning signs including a socket on the gooseneck and on the rear panel on the left and right -6 pairs of threaded blocks between the lashing rings under the top strap on the outer support for mounting screwable RUD rings VLBG-4 -ALU side walls and rear wall can be plugged into the gooseneck approx. 2,440 x 400 mm -The rear galvanized plug-in stanchions are removable (Length of the body approx. 2,560 mm) -Gooseneck in the rear upper area closed with a removable cover -5 pairs of stake pockets for 100 x 50 mm stakes in the outer frame of the loading area -Foldable extensions, approx. 230 mm per side -2 pairs of screwable RUD rings VLBG-4 M24 (LC 8,000 daN) -1 pair of steel ramps to bridge the hooks of the low bed -A painted layer of sand on the loading area as anti-slip protection -Speed sticker 80 km/h at the rear and on both sides -Dipper handle recess of the rear chassis closed at the rear with a plug-in plate -Four warning signs extendable by approx. 400 mm, approx. 423 x 423 mm -Radio remote control for the steering in addition to the cable remote control, with indicator lights on the receiver as Alignment control -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 normal grease -Load pressure gauge for determining axle loads -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot blasted, then the defined visible surfaces are hot-finished in metallization with ZINACOR 850 (zinc 85% - aluminum 15%)

Condition: ready for operation (used), machine/vehicle number: 5722, table mounting size: 190 x 710 mm table movement x: 390/360 mm table movement y: 150 mm table movement z: 280 mm spindle taper: SK 40 spindle turning speed range: 100 - 3100 rpm carriages longitudinal: 0 - 600 mm/min electrical connection: 380 V, ca. 1,5 kW Bdjdpfeflrg Tex Ammjc space needed: 1400 x 1200 x 1500 mm weight: ca. 680 kg

Year of construction: 2026, condition: new, IWR 2000D - The fruit washer with mill for fruits and vegetables is made entirely of high-quality stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. The fruits are immersed in water and, after pre-washing, transported via the conveyor belt where they are thoroughly cleaned with fresh water. Afterwards, the cleaned fruits enter the mill, where they are processed to the desired mash consistency using the selected sieve. The washing system is also equipped with a dosing attachment for pack presses. Technical Information • Nominal capacity: 1500 kg/h Bsdpfx Amstu Ikcomedc • Power requirement: 3 kW, 400 V, 16 A • Material: WNr. 1.4301, AISI 304 stainless steel • Washing tank water capacity: 120 L per batch • Water consumption: 12 L/min • Water connection: 3/4” quick coupling • Electric control cabinet with IP65 protection rating • Swiveling Rätz mill • Equipped with rollable wheels • Easy to clean • Through the frequency converter, the conveyor capacity can be easily adjusted Dimensions: Length: 3250 mm Width: 840 mm Height: 2270 mm Weight: 160 kg

Condition: good (used), Year of construction: 1962, High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm Bodpfeirax Uex Ammodc -Weight: 1500kg

Condition: excellent (used), Year of construction: 1990, MAHO MH 500W with Heidenhain TNC 320 The machine comes from a training workshop and is in very good condition. The TNC 320 offers intuitive and highly flexible operation and programming according to current industry standards. Technical specifications: - Heidenhain TNC 320 retrofit - Travel X- 500 mm, Y- 380 mm, Z- 350 mm - Spindle taper SK 40 - Vertical quill stroke 50 mm - Spindle speeds 20–3150 rpm, stepless - Feed rate 1–3000 mm/min - Rapid traverse 5 m/min - Table load capacity 250 kg - Total power requirement 11.3 kW - Machine weight approx. 2 t - Handheld control unit - Safety guard An on-site inspection/test under power is, of course, possible. Bdedsxw N S Ispfx Ammec We are happy to offer transport, installation, and commissioning at your location. Everything from a single source: We, Baumgärtner CNC GmbH, are a company specialized in: - Service - Maintenance - Overhaul - Automation of DMG machines and equipment from other renowned manufacturers. We support you throughout the entire process! From machine purchase, transport, and delivery, up to commissioning and subsequent maintenance or repair work – you can rely on us.