Complete production line

BUD-MASZ monterrey

Condition: good (used), functionality: fully functional, total length: 2,750 mm, total width: 2,800 mm, total height: 1,830 mm, space requirement length: 2,800 mm, space requirement width: 2,850 mm, space requirement height: 1,900 mm, motor manufacturer: Bitzer, volume flow: 940 m³/h, Two used Bitzer screw compressor skids for low-temperature applications on Freon. Both skids are supplied with a shared control panel. Originally, each skid served its own cold storage room, but the capacities listed in the specifications are combined. Skid 1 is equipped with two Bitzer HSN 7461-70-40P semi-hermetic screw compressors, a Bitzer FS 3102 liquid receiver, a Bitzer OA4088 oil separator, a brazed plate heat exchanger used as an economizer, a brazed plate heat exchanger for heat recovery, and pressure and safety switches. This skid has a displacement of 440 m³/h at 50 Hz and 532 m³/h at 60 Hz. Skid 2 comes with two Bitzer HSN 7471-75 semi-hermetic screw compressors, a Bitzer FS 3102 liquid receiver, a Bitzer OA4088 oil separator, a brazed plate heat exchanger used as an economizer, a WTT GmbH WP 7M-44 brazed plate heat exchanger for heat recovery, and pressure and safety switches. This skid has a displacement of 500 m³/h at 50 Hz and 600 m³/h at 60 Hz. Bitzer HSN 7461-70-40P (x2) capacities: -20ºC/+40ºC: 229.6 kW -30ºC/+40ºC: 157.4 kW -40ºC/+40ºC: 102.0 kW -45ºC/+40ºC: 79.8 kW Bitzer HSN 7471-75 (x2) capacities: -20ºC/+40ºC: 240.6 kW Gbodpfsx Ap Hpsx Anrsl -30ºC/+40ºC: 165.8 kW -40ºC/+40ºC: 109.0 kW -45ºC/+40ºC: 86.0 kW

Condition: new, Year of construction: 2025, NEW Snap lock roofing panel roll forming machine SL-1 Snap lock roofing panel roll forming machine SL-1 is designed and manufactured by our company as one of the flagman equipment for metal roofing panels production. Following machine makes standing seam roofing panels with self-closing lock on sides (snap lock). The main advantage of such lock system is the easy way of installation: to connect two panels with each other you just need to cover bottom part with top part and press it with some force, you will hear specific click noise at this very moment. That is why name of system is self-closing lock one. Comparing to standard standing seam roofing panels with mechanical lock which you need to close with special tools or equipment, snap lock panels are much easier to install and don’t require additional expensive devices for work. To fix panels at the roof frame you can use standard self-tapping screws, to make it possible, while rolling machine makes special fixation holes on one side of roofing panels. Such simple product design also helps to save costs and make installation process easier, not spending money on clips purchasing, comparing to the standard standing seam metal roofing with mechanical lock installation. So standing seam roofing with snap lock is easier to install, does not require high skilled employees and cut expenses for additional machines purchases. Total high of panels - 31mm Gbjdjiuz T Ispfx Anrjl As per order, we can also make machine for 26mm panels high. Machine has 10 pairs of forming rolls. One of the rolls has special punching parts so can cut fixation holes at roofing panel for further installation operations. Cutting tools are made from tools steel with heating and polishing, so have longtime working period. Maximum metal width can be 700mm, minimum 250mm. Snap lock roofing panel roll forming machine SL-1 is width easy adjustable one, so to adjust machine from one panel width to another you just need to rotate special handle. Rolling length – unlimited Rolling speed (m/min.): about 7 As extra options, you can get: - cross cutting knife; - length measuring device; - ribbed panel rolls; As per customer preferences snap lock roll forming machine can be equipped with automatization system and electric shears for panels cutting. Standard supply set of self-closing lock roll former machine SL-1 includes safety covers to protect working parts of machine from foreign objects. Snap lock machine can work with various types of metal: galvanized steel, copper, aluminum, color coated metal, etc.

Condition: new, Year of construction: 2025, machine/vehicle number: 947526697, Frumecar ECA 500 fully mobile concrete batching plant production capacity: 30 m³/h * 4 aggregate hoppers * vertical axle mixer TRH-750 with a capacity of 750 liters * plant don't need any foundation and could be assembled in 1 day * 1 year guarantee from startup * ask for specific offer and technical details more machines and mixing plants on our website Gbodpehd I Sqofx Anrsl more information Application: Building industry, Applicable material: Concrete, General

Year of construction: 1976, condition: good (used), strip width: 300 - 1.350 mm strip thickness: 0,35 - 3 mm Gjdjbh Ubwspfx Anrebl coil weight: 12,5 t mandrel Ø: 508 mm

Year of construction: 1990, condition: new, Brand SKF Type 6202-Z/QE6 Year of manufacture: Unused Weight (kg) approx. 9400 gross / 8780 net Number of pieces in stock 193.200 ( approx) Made in France Comments Contact us for min. quantity Verkoopcondities Contact us for min. quantity Gjdsqa Am Topfx Anrobl

Year of construction: 1971, condition: good (used), decoiler - expansion mandrel with coil lifting table strip width: 1.200 mm Godpfx Aod Ha E Ssnrsbl strip thickness: 0,3 - 5 mm coil weight: 10 t mandrel Ø: 508 mm

Condition: new, Year of construction: 2025, Roll forming metal siding “double façade panel” machine SPM-2 Roll forming metal siding “double façade panel” machine SPM-2 is new design product of our company for façade and wall metal panels forming with the necessary configuration. These double façade panels are very popular in construction business of cladding residential buildings and industrial structures, for the construction of fences of various configurations, gazebos, roofing elements, etc. The SPM-2 metal siding production line is fully automatic and consists of a rolling part of the machine, an automation system and guillotine cutting shears at the machine exit. The line can have as additional parts a manual or automatic uncoiler for metal rolls, depending on the customer's needs. As standard version, this metal siding double façade panels roll forming machine SPM-2 makes a flat panel profile, but with the additional equipment, it is possible to roll panels with a microwave or rib shape profile. To start rolling, it is necessary to install a roll of metal to the decoiler and to put the end of the strip to the first rolling rollers of the equipment and feed it into them. After step by step, to put the metal to the next rollers, adjusting it if necessary. When metal comes to the cutting device of machine you need to feed metal into cutting knives and to make “zero” cut. After such step, equipment can move to automatic operation mode. The control panel of machine has the ability to set the number of tasks and the length of products, single tasks or to work in multitasking mode. After setting up necessary parameters the machine will automatically roll the metal cladding wall panels and cut them into necessary sizes. Thus, the customer will receive final product as quickly as possible and with the highest possible result. The roll forming speed is adjustable and can be up to 10-15 meters per minute. The SPM-2 metal wall cladding panels production line has special tools for punching out fastening holes on the side of the panel. It makes possible for the customer to get more interesting solution options and to offer a wider range of products to the end user. The rolling part of the machine has 18 pairs of forming steps, ensuring high quality of final product. You can get machine with protective cover or without it as per your request preferences. Specifications Material width (mm) 416 The material thickness (mm) 0,4-0,5 Engine power (kW) 3 + 1,1 Gjdpfx Aexghngenrsbl Rolling speed (m/min) 10-15

Condition: good (used), Feed through production line for wooden doors very hight efficiency one complete door in 30 seconds (lock hole, handle hole, anuba hinges) Machine composed from two parts - so in the same time 2 doors are processed each from both sides Gbodpfsuq Scpex Anrol Each part of the machine can work independent on the left side and right side Part 1 - left side milling for strike plate and milling handle hole and key hole - right side in the same time makes boring for anuba hinges Part 2 - left side milling for lock hole - right side in the same time makes inserting anuba hinges

Condition: new, Year of construction: 2025, Metal picket fence roll forming machine MFP-1 was designed by our company to produce semi-round shape picket metal fence profile. This profile is widely used and popular among companies with business in manufacturing, installation and selling of metal fences. The production of the profile goes gradually, at first hemming forms on edges from the flat metal, and then the height of the profile and the semi-round shape are formed, at the last stage of rolling machine forms the rib in the profile center. Such number of forming stages makes it possible to ensure smooth sheet changes during rolling, as well as high quality of the final product. Gbodjm Twnlspfx Anrol As a blank, you can use a strip of required width and length, to prepare it with pre-cut on other equipment – sheet metal slitting machine or guillotine shear. After roll forming, to make fence picket end look better, you can use special cutting press of our production. The working tools of such press have special round configuration and are the same as semi-round metal picket shape to make appropriate cutting. Those tools are made from special tool steel, and goes through process of hardening so ensure high requirements for the cutting tools of the equipment. Our company can produce as semi-automatic rolling machine for the metal fence pickets manufacturing and a manual punching press for it, as well as a fully automatic line. Such metal fence automatic line can have following components: console metal decoiler, a rolling machine equipped with an automatization system with the ability to program the number of required pickets for rolling and their lengths, automatic electric shear for cutting metal at the end and stacker part. Thus, cooperating with us, our customers can choose the best option for their manufacturing process according to their planned production volumes, budget, etc. For more details about metal picket fence roll forming machine MFP-1 please contact our sales department

Condition: like new (used), functionality: fully functional, Year of construction: 2023, Usable length: 6200 mm Bending capacity steel 400 N/mm: 2.00 mm Stainless steel 600 N/mm: 1.50 mm Aluminum 190 N/mm: 3.00 mm Number of uprights: 6 Driven bending joints: 6 Insertion depth: 1165 mm Connection: 400V/3Ph/50Hz Other data and dimensions: see brochure Includes hydraulic jaw adjustment to compensate for different sheet thicknesses Godpjyxchnefx Anrjbl Includes adjustable jaw preload Includes 2 hydraulic pressure stages Includes safety package Includes 10 x 60 mm, 2-piece bending jaw extension rail Includes 2-way foot switch for clamping jaw open/close + automatic bending jaw start Includes resettable sheet metal grid Includes water groove in the clamping jaw BMS Multi-Touch control with electronic depth stop TAZ 1000 With this Windows-based, graphical touchscreen control, profiles can be selected by simply tapping. The simulation program allows you to observe the complete bending process of a previously saved profile, as well as newly entered profiles. The depth stop is electronically driven via toothed belts and is equipped with four stop fingers. The fingers are infinitely adjustable along the entire machine length. Depth stop measuring range: 10/30 - 945 mm. Network connection for remote maintenance Electric cutting device S2 Cutting capacity: Steel 400 N/mm²: 2.00 mm Stainless steel 600 N/mm²: 1.25 mm Aluminum 190 N/mm²: 2.50 mm Includes optional conical depth stop for narrow/wide edges for easy joining of sheets Measuring range: 10/30 - 885 mm