Hydraulic pump 3 kW 250 bar

Brüninghaus OVS 0 28 DFR/30

Condition: new, Year of construction: 2026, CORMAK HBS275 band saw, equipped with a hydraulic cylinder, a cooling system and an arm swivelling up to 60º, together with blades from renowned German company Röntgen, is used commonly in ironworking, where precision, quality and cutting speed are essential. Horizontal band saw with a swivelling arm for cutting metals, allows for cutting in plane perpendicular to the axis of material cut and at any angle from 0 to 60º. Material for cutting can be fed manually or with any mechanical feeding device, with automatic tool feed. Band guides are equipped with dedicated carbide plates and bearings. This has a huge impact on band guiding, its durability, cut straightness, cutting accuracy and quality. Carbide guiding drastically reduces the wear of the machine and blades. Machine's arm made of uniform cast iron as well as a 27 mm wide cutting band are capable of low and high quantity cutting of profiles and other materials. The vice is located in an adjustable bed, equipped with a quick clamp. Blade guides have cemented carbide plates and roller bearings. Its these cemented carbide guides that provide cut precision and straightness. The arm, positioned at an angle of 25º, thus increasing blade durability. To the bottom of the arm a brush wire is attached, ensuring clean and functional brush. Machine's drive is transmitted through a worm drive. A 3-phase motor with 2 cutting speeds and motor thermal protection. This cutting machine also has a strain gauge - a band tension sensor and an automatic switch-off in case the cutting band breaks. Upper part of the base constitutes a tank for flood coolant draining and chips produced during cutting. A cast iron workbench is attached to the base, with a swivel arm and control panel on separate arm. The main cutting move in the cutting process is moving the cutting band and the arm lowering feed. The arm lowering speed (the cutting speed) is adjusted with the hydraulic cylinder. The feed speed is controlled by the control panel. There are 2 cutting band speeds to choose from: 37.5 and 75 m/min. In rest arm position (after the cutting process) the cutting band drive is switched off automatically. Safety is ensured with cutting band guards and microswitches stopping the motor after cutting cycle is finished or after any of the guards are opened; additional protection consists of automatic switch-off of the band saw in case the cutting band breaks. Technical data Total power 1.5 kW Power supply 400V 50Hz Arm lowering control hydraulic cylinder Band dimensions 2455 x 27 x 0.9 mm Band speed 37.5/75 m/min Vice base height 900 mm Weight 215 kg Angle 0º ø220 260 x 140 200 x 200 45º R ø160 160 x 140 160 x 160 60º R ø100 120 x 100 100 x 100 Lodpfx Ajudi Unopmohi

Year of construction: 2018, condition: as good as new (ex-display), Welding rotary table KT 50 Lhedpfx Aped A Etyomsi Load capacity, horizontal: 50 kg, tilted: 25 kg Power supply: 220 V, 50 Hz Table diameter: 320 mm Table height: 400 mm, tilted to center: 300 mm Length: 650 mm, width: 650 mm Tilting range, continuously adjustable via crank drive motor: 0 – 90° Speed: 1.7 – 15 rpm Includes foot-operated remote control

Condition: used, TECHNICAL DETAILS - number of spindles : 6 independent - bar clearance : 32 [mm] - maxi spindle speed : 6 300 [rpm] - machine equipped with 28 numerical axes - slide unity 1.1 : X and Z axes controlled by CNC - slide unity 2.2 : X and Z axes controlled by CNC - slide unity 3.1 : X and Z axes controlled by CNC - slide unity 3.2 : X and Z axes controlled by CNC - slide unity 4.1 : X and Z axes controlled by CNC - slide unity 4.2 : X and Z axes controlled by CNC - slide unity 5.1 : X and Z axes controlled by CNC - slide unity 5.2 : X and Z axes controlled by CNC - slide unity 6.1 : X and Z axes controlled by CNC - slide unity 6.2 : X and Z axes controlled by CNC - synchronous unit, spindle position 6.1 EQUIPMENT Lhjdouhauyspfx Apmei - INDEX C200-4 control (Siemens SINUMERIK 840D) - Simple NCU - IEMCA SIR MS32/33/P bar feeder - Coolant tank: KNOLL AE 1076 * with high-pressure pump - KNOLL VRF 500 chips conveyor - Parts catcher with conveyor in position 6

Condition: used, machine/vehicle number: 1 284 066, Feed diameter: 200 mm Through-hole: 50 mm Mounting, short taper according to DIN 55027: Size 6 Outer diameter of the clamping cylinder: 290 mm Overall height (clamping cylinder to the front of the chuck, without jaws): 150 mm Ledpfecm Tgksx Apmjhi pneumatically actuated

Condition: used, Year of construction: 2002, turning diameter max. 420 mm turning length 1250 mm control INDEX, C 200-4 D swing diameter 630 mm travel x1 320 mm travel z1 1250 mm travel x2 170 mm travel z2 1250 mm travel x3 320 mm travel z3 1250 mm main spindle speed max. 3000 U/min main spindle drive 53 kW spindle passage 102 mm spindle head DIN 55026 Gr. 11 max. torque on the spindle 675 Nm sub spindle - spindle speed range max. 3000 U/min sub spindle drive 53 kW sub spindle - spindle passage 102 sub spindle - spindle head DIN 55026 Gr. 11 sub spindle - spindle torque 675 Nm travel sub spindle 1250 mm feed power X1 14000/Z1 14000 N rapid traverse X1 20/Z1 40 m/min feed power X2 8600/Z2 14000 N rapid traverse X2 20/Z2 40 m/min feed power X3 14000/Z3 14000 N rapid traverse X3 20/Z3 40 m/min numbers of turret head positions Rev. 1 = 12 numbers of turret head positions Rev. 2 = 10 numbers of turret head positions Rev. 3 = 12 number of driven tool stations 12 / 10 / 12 speed of driven tools max. 6000 U/min max. torque 36 / 21 / 36 Nm tool taper DIN 69880 tool taper ø 40 x 63 mm total power requirement 120 kW weight of the machine ca. 19 t dimensions of machine L x W x H 5,77 x 2,47 x 2,62 m Ljdpfxst U R Hzo Apmjhi Accessories: segment bushing chuck HAINBUCH on main spindle, collet chuck HAINBUCH, SPANNTOP SP on sub spindle, various tool holders (also for driven tools), chip conveyor, coolant - all 3 turrets are prepared for coolant through spindle, but the highpressure coolant pump and tank are not with the machine -

Condition: used, Roll sets for profile bending machine, 3-roller ring bending machine HERKULES WETZLAR The rollers are suitable for a HERKULES WETZLAR profile bending machine, type BO 238 N. Lhodpfeglaq Iex Apmoi Shaft diameter: 60 mm with an 18 mm keyway. 2 pieces, roller set No. 1, roller diameter 110 mm, roller width = 180 mm. 2 pieces, roller set No. 2, roller diameter 160 mm, roller width = 40 mm. 3 pieces, roller set No. 3, roller diameter 150 mm, for pipe diameter Ø 33 mm, roller width 87 / 115 mm. - Roller set No. 3 with adapter ring from Ø 93 to Ø 60 mm, without keyway. The machine had 2 driven rollers. Total weight of all rollers: 57 kg. Good condition.

Condition: used, Gearbox, bevel gear, worm gear -Gearbox: Worm gear ratio: i = 7.5 Lhodpfx Ajt Snw Sjpmsi -Shafts: Ø 14 x 34 mm / see photos -Dimensions: 122/105/H140 mm -Weight: 4.2 kg

Condition: used, TECHNICAL DETAILS - Number of spindles : 2 - Number of axes : 8 Ledpfx Asuhbpfopmshi - Number of turrets : 2 MAIN SPINDLE - Spindle power : 53 / 68 [kW] - Spindle speeds : 3000 [rpm] - Max. bar diameter : 102 [mm] - 1 - Saisie libre : 2000 [mm] - Max. chuck diameter : 420 [mm] - Rapid traverse rate : 30 [m/min] - C axis indexing precision : 0,001 [°] COUNTER-SPINDLE - Spindle power : 50 / 70.5 [kW] - Spindle speeds : 3000 [rpm] - Max. bar diameter : 102 [mm] - Rapid traverse rate : 30 [m/min] - C axis indexing precision : 0,001 [°] UPPER LEFT TURRET - Number of positions : 12 - Number of motorized positions : 12 - Tool holder type : VDI 40 - X/Z stroke : 320 x 2.000 [mm] - Y stroke : 210 [mm] - Live tools speed : 6000 [rpm] - Live tools power : 17 [kW] LOWER RIGHT TURRET - Number of positions : 10 - Number of motorized positions : 10 - Tool holder type : VDI 40 - X/Z stroke : 210 x 2.000 [mm] - Live tools speed : 6000 [rpm] - Live tools power : 11.3 [kW] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 137 [kW] WEIGHT & DIMENSIONS - Machine floor space : 9.000 x 3.500 [mm] - Machine height : 3.000 [mm] - Machine weight : 21.000 [kg] MACHINE HOURS - Number of working hours : 34274 [h] EQUIPMENT - CNC : INDEX C200-4D (Siemens 840D) - Coolant tank : KNOLL * with high-pressure pump : 80 [bars] * with paper filtering unit - Automatic doors - Chips conveyor : Droite

Condition: refurbished (used), 60 m³ / 60,000 l fire water tank according to DIN 14230 Tank volume: 60,000 liters / 60 m³ Length: approx. 12,680 mm Diameter: approx. 2,500 mm Weight: approx. 9,500 kg Material: Steel, material S 235 JRG 2 Underground tank for underground storage, single- or double-walled, suitable for areas that can be walked or driven on (load class SLW 30) with 1 dome (outer diameter 720 mm) with a blind cover, seal and screws. New or used, immediately available! The container has been emptied, cleaned, overhauled and tested for tightness by us as a specialist company. The container complies with the requirements of DIN 14230 (Underground fire water tank): - Fire water suction connection according to DIN 14244 with a mounted fire brigade coupling / fixed coupling A according to DIN 14319 in form B without a level gauge - Ventilation flange stub in DN 100 with cap with a total length of approx. 1,300 mm, suitable for 800 mm ground cover and 500 mm above ground - Externally coated with a bitumen coating for protection - Upon request, we can coat the tank with an internal full coating based on bitumen or an epoxy resin internal coating (against corrosion) - It is also possible to line the container with a plastic inner liner Cost-effective delivery with our own truck is possible. Simply let us know the delivery location, and you will immediately receive the exact freight costs. An inspection is possible at any time by prior appointment. If you require any further information, please call us or send us an email to b.barth(at)barth-tank.de We can also accept and purchase tanks/containers of all kinds, simply contact us. We also have these types of tanks constantly in stock in the following sizes: Lhedjhh Sruspfx Apmei - 10,000, 13,000, 16,000, 20,000, 25,000, 30,000, 40,000, 50,000, 60,000, 80,000 liters

Condition: used, final pressure: 1,400 bar, pressure: 1,400 bar, Good working high pressure pump with 20mm plungers 1400 bar 35 ltr/min Lhodpfev Suhzjx Apmji IL 375 TF375H