Hydraulic clamping device

Behringer Doppelspannstock HBP 360A

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. • The saw band is tensioned via a hydraulic cylinder, which is carried out by Itsdpfx Aaefg E Hpe Ejr the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: used, A.COSTA LEOPARD multirip saw with double arbor - Max cutting depth: 200 mm Itjdpfx Aasvf Dags Ejr - Width of track: 350 mm - 2 x 55 KW / 75 HP - Weight: around 5 tons

Condition: used, Year of construction: 2002, functionality: fully functional, machine/vehicle number: 220992, SECOND HAND END CUTTING SAW WITH ELECTRONIC PUSH FEED STROMAB MOD. TR500 MATRIX - CE RULES - infeed with roller table and electronic push feed MATRIX of 6000mm - Outfeed roller table1500mm - 10 hp motor - Blade diameter: 500mm - Blade rotation speed: 3500 rpm - Maximum cutting capacity: 360mm (L) at 55mm (H), 200mm (L) at 135mm (H) - Minimum cutting section: 20mm (L) x 10mm (H) - ELCO numerical control - 415 volts - Serial number: 220992 - Year 2002 Isdpst U I A Hjfx Aa Eotr

Year of construction: 2020, condition: new, Available from stock Strip dimensions: 4420 x 34 x 1.1 mm Itedpfeiryf Sjx Aa Ejr Cutting capacity (square): 360 x 400 mm Cutting capacity (round): 360 mm bundled cutting: 180 - 280 x 50 - 160 mm Cutting speed: 35 - 85 m/min Motor power main drive: 3.75 kW Engine power hydraulic pump: 0.75 kW Motor power coolant pump: 0.125 kW table height: 755 mm Weight: 1680 kg Dimensions W x D x H: 2400 x 2120 x 1840 mm

Condition: used, Year of construction: 1995, 1995 Friulmac FN7 1300 Cutting-off machine for Parquet heads or similar products. Maximum opening 1,400 mm Itedpfx Aaouichre Esr Maximum step width 220 mm

Condition: refurbished (used), functionality: fully functional, saw blade diameter: 360 mm, cutting height (max.): 100 mm, cutting range round steel at 90°: 100 mm, section length (min.): 300 mm, Fully automatic carbide circular saw machine type KMR 100 AP Refurbished to mint condition - available ex stock Working range: Round material 20 - 100 mm Square material 20 - 80 mm DRIVE PERFORMANCE Frequency-controlled saw motor 11.0 kW cuting speeds 20 - 150 m/min incl. Infeed magazine and sorting for trim cuts/rest pieces and good parts Suitable for cut off length up to 300 mm Iodpsh Uqpvofx Aa Ejtr Cutting time for Ø 100 mm solid material 1.0037 approx. 7 seconds !!

Condition: good (used), Year of construction: 2010, product length: 600mm - 1300mm Isdpsm Dqk Usfx Aa Eotr product width: 185mm - 400mm

Year of construction: 1996, condition: excellent (used), Automatic slotting machine with two oscillating tables BALESTRINI 2CAP Maximum length of the groove 120 mm Maximum recess depth in mm 80 Spindle speed 9000 rpm Spindle motor 3 Hp Oscillating motor Hp 1 Pneumatic clamp for the workpiece Overall dimensions: mm 1000 x 900 x 1250 Weight kg 500 Isdpogmucpefx Aa Eotr

Condition: new, Year of construction: 2025, saw band length: 4,420 mm, saw band width: 34 mm, Double-column bandsaw, fully automatic Everising H-360 HB Cutting range round: 0 - 360mm Cutting range square: 360 x 360mm Bundle tension: Width: 180 - 280mm Bundle tension height: 50 - 160mm Drive power: 3.7 kW Saw blade dimensions: 4420 x 34 x 1.1mm Weight: 2310 KG Machine dimension 2500 x 2200mm The standard equipment of the machines is as follows: Solid steel construction in double column principle Itodpfsq St U Nox Aa Esr - NC feed system - Frequency-controlled cutting speed (infinitely variable, inverter-controlled) - Digital cutting speed display - Hydraulically controlled double horizontal clamping vices - Hydraulic saw blade tensioning - Saw band guides (incl. band back guide) made of carbide - Hydraulically pre-tensioned band guides - Precise PLC control (SPS) for all hydraulic and electrical components. - Cutting counter with automatic switch-off - Automatic out-of-stock switch-off - Multi-job function - Bundle clamping device - Driven chip brush - Automatic band breakage control incl. emergency stop - Chip flushing gun - Flexible work light - 2 meter roller conveyor - Tool box - Carbide function Special equipment included: - Variable clamping pressure reduction - Cutting process control Extensive complete German documentation.

Year of construction: 1985, condition: ready for operation (used), Double-sided tenoning machine for parquet FOD Iodpsilc Ncsfx Aa Eetr DOUBLE-SIDED for parquet production, it has a face leveling saw and a vertical cutter for the production of a groove