Vickers Hardness Tester

AFFRI WIKI 90

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: Bwsdpfohzbipex Agzoi 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: refurbished (used), Year of construction: 1974, functionality: fully functional, machine/vehicle number: 1276, CNC Hot Radial Forging GFM SX-13 New in 1974 / 2022 New control system PLC SIEMENS S7 Machine number: 1276 No. of Hammers: 4 Forging force each hummer: 160 Ton Hammer stroke / min: 700/min Hammer lenght: 240 mm Diameter setting range: 80 mm Maximum forging diameter: Structural steel, round-cross section: Ø 130 mm square cross section: Ø 115 mm Smallest dimensions forged: Ø 25 mm Manipulator A max. displacement: 6820 mm Manipulator B max. displacement: 7150 mm Maximum workpiece length: 6000 mm Rapid speed manipulator: 400mm/sec Total connected power: 300 kW 380 V, 50 Hz Machine dimensions: Forging height over floor: 615 mm Total height pf the machinr over floor: 1665 mm Total machine lenght: 32670 mm Total foundation lenght: 33400 mm Tot. machine width (without auxliary equipments): approx 3885 mm Bedpfoq U R T Njx Agzewi Total foundation width: 16000 mm Total weight of the machine: 84.000 Kg

Year of construction: 2024, condition: new, machine/vehicle number: H3000-H5000TM, Universal testing machine H3000TM-H5000TM according to DIN EN ISO 7500 The universal testing machine of the H3000TM-H5000TM series is a single-spindle machine, a robust construction made of aluminum and V2a with ball screws, ball bushing guides and toothed belt drive. The bellows cover protects the spindle and guides. The testing machine is microprocessor controlled and has a membrane keypad. The 2-line LCD display shows the force and travel. The testing machine can be used as standalone or with a PC via USB interface. The displacement is measured by means of an encoder 0.01 mm visible resolution on LCD (internal 0.0001mm). The machine is manufactured with a standard load cell: 0.03% linearity and the corresponding calibration. Optionally it is possible to add a second channel for a second load cell or a displacement transducer. The universal testing machine is manufactured with two different travels, 500mm or 1200mm (without load cell and testing tool). Bwsdpfsiq Hxksx Agzsi Further scope of delivery: One load cell up to nominal load, 220 Volt cable, USB cable, description, CE declaration of conformity. For more information, please refer to the attached description. Load cell 3000N-5000N Measuring range: 5-5000N tension and compression, with nom. 2mV/V output signal, overload protection: +/- 1000%, linearity: +/- 0.05%, hysteresis: +/- 0.03%, repeatability: +/- 0.02%, with, incl. 1.5m connection cable incl. calibration certificate Long travel extensometer HE 900mm measuring travel, measuring arms motorized, including electronics Accuracy class class 1 from 1mm travel according to DIN EN ISO 9513 Measuring principle optical incremental Measuring path 900 mm , minus measuring length Display error 6 µm or 2 Resolution 1 µm Actuating force 10 cN Standard initial device measuring length (Lo) 10-100 mm, in 5 mm steps Lo adjustment is manual Measuring arm opening and closing is motorized specimen diameter 0-30 mm specimen thickness 0-30 mm sample width 0-100 mm Weight approx. 32kg Scope of delivery strain gauge complete with electronics Cutting edges round: 1 set each carbide / rubber wear parts measuring blades optional rectangular cutting edges ATTENTION: When using optional cutting edges a readjustment of the lo a readjustment of the lo stop is necessary.

Condition: new, Year of construction: 2024, ✅ New goods ✅ Top price ✅ Immediately available ✅ Shipping possible ◾ SCHORR electric high lift truck ◾ Model RR12HH with 3500mm lifting height ◾ Low maintenance and smooth running ◾ Including 24V batteries and charging station ◾ 1.2t / 1200kg load capacity ◾ Top price-performance ratio ◾ AVAILABLE IMMEDIATELY! Gross price: 3.399,00€ incl. VAT Bwedeidqr Sepfx Agzsi Net price: 2.856,30€ excl. VAT The electric high lift trucks from SCHORR offer an excellent price-performance ratio. The off-centre drive unit allows a small turning radius with best all-round visibility. Each model is equipped with a multifunction tiller which displays the current battery level and can be started via the ignition lock. The tiller can be operated with both hands and also has a worm mode. The design of the pallet truck is both robust and easy to maintain; impact-prone areas are equipped with yielding plastic. The emergency stop switch is centrally located for easy access at all times. The lift trucks are equipped with tandem load rollers as standard, which overcome uneven surfaces such as paving stones with low noise and vibration. TECHNICAL DATA see picture Further data and information on request, we look forward to your call or message!

Condition: good (used), turning length: 6,000 mm, spindle bore: 260 mm, Swing over bed Ø: 850mm Swing over cross slide Ø:500mm DBC Turning Length: 6000mm Spindle bore: 260mm Spindle power: 28kW Bed width: 650mm Stroke pinole: 300mm Spindle taper: 6Mk Workpiece weight: 5000 Length: 10000mm Bsdswvtg Aopfx Agzswi Width: 2100mm Height: 2600mm Weight: 12800kg

Condition: good (used), functionality: fully functional, Year of construction: 2006, laser power: 4,000 W, AVAILABLE AT SHORT NOTICE: TRUMPF Trumatic L 3030 - 4 kw - Year 2006 TECHNICAL DATA: Make: TRUMPF Type: L 3030 - 4 kw Year of manufacture: 2006 Working area: 3,000 x 1,500 x 115 mm Control: Siemens Sinumerik 840 D Laser power: 4,000 watts Max. Sheet thickness mild steel: 20 mm Max. Sheet thickness stainless steel: 15 mm Max. Sheet thickness aluminum: 10 mm Operating hours: NC Machine regularly serviced by TRUMPF! Transmitter tube: new 2024 TASC laser control: new 2022 Driver stage: replaced 2018 Magnetic bearing electronics: new 2016 STANDARD EQUIPMENT: - Closed machine frame with integrated laser unit Laser unit: TLF 2000 high-frequency excited CO2 laser, maintenance-free turboradial blower, mirror telescope, cooling unit, logbook function - Automatic pallet changer - Longitudinal conveyor belt for small parts/waste - Drives: maintenance-free three-phase servomotors - Cutting head quick-change device - Laser cutting head with 5" lens and laser cutting head with 7.5" lens - Programmable cutting gas pressure setting - APC capacitive height control and process control - AutoLas Plus automatic focus position adjustment - Laser power control - Position laser diode - HI-LAS high-pressure cutting - Fast processing with SprintLas - ContourLas for the production of small holes - PMS plasma sensor technology - Automatic sheet edge detection - Programmable power cycles - Microweld - Automatic switch-off - Work area lighting - Sinumerik 840D control system: open control system on PC basis, simple operation, online help, integrated e-shop, diagnostic functions, maintenance logbook, technology data, teleservice - Workshop programming ToPs 100 lite - Safety: multi-beam light barriers, beam guidance fully encapsulated and ventilated, monitoring system, multi-chamber extraction and compact dust extractor, protective cabin - 3.5" floppy disk drive - TFT color screen - Electrical equipment: Voltage 400 V / 50 Hz - Paint finish: Standard RAL 9002/5010 EXTENDED EQUIPMENT: Bwjdeuthz Tepfx Agzsi - TLF 4000 laser incl. lens monitoring sensors - PCS Process Control System

Condition: used, Thread rolling machine ORT RP30U Bwodpjt H Ty Usfx Agzsi 2-roll 30 ton swiveling heads variable speed drive #1331 Under power in our warehouse in Gussago BS. Test run possible M i m u Machine Tools Italy Rolling is a mechanical process without chip removal that can be performed cold or hot, having as a purpose the improvement of the surface finish (therefore the fatigue behavior Power (Ton): 30 Number of rollers: 2

Condition: new, Year of construction: 2025, The XTON Smart Cleaner SC1000™ automatic basket washer is constructed from stainless steel AISI 304 and acid-resistant steel AISI 316. It is designed for use in various industrial and automotive applications. This washer is intended for degreasing and cleaning parts contaminated with oil or grease, without damaging the surface of the cleaned element. Cleaning efficiency is enhanced by our proprietary XPOWER Active Cleaner BA, which, combined with the appropriate temperature and pressure, easily removes all types of dirt. The machine operates in a closed-loop system at temperatures up to 80°C. Standard equipment includes a rotating basket with a diameter of 100 cm and a 300-liter tank, which can be optionally thermally insulated to protect the heated fluid from cooling too quickly. The Smart Cleaner SC1000™ ensures high cleaning quality, time and energy savings, as well as safe and convenient operation. It is designed for automatically removing dirt from cast iron, aluminum, and steel surfaces. The design and construction of the Smart Cleaner SC1000™ adhere to the highest quality standards ISO 9001 and environmental standards ISO 14001. EQUIPMENT: - Rotating basket with a diameter of 100 cm - Heated tank with a capacity of 300 liters - Dual liquid filtration system - Liquid level and temperature sensors - Oil separator - Adjustable feet with a height adjustment range of 100 mm - XTON Active Cleaner BA (5L starter pack) TECHNICAL PARAMETERS: - Weight: 200 kg - External dimensions - Open chamber (W x D x H): 150 x 120 x 250 cm - External dimensions - Closed chamber (W x D x H): 150 x 120 x 140 cm - Rotating basket diameter: 100 cm - Rotating basket load capacity: 300 kg - Work time programming range: 0 - 99 min - Washing/liquid temperature: up to 80°C - Heater power: 9 kW - Tank capacity: 300 L - Tank capacity to oil separator level: 200 L - Pump capacity: 250 L/min - Spray pressure: 4.5 - 6 bar - Power supply: 3 x 400 V - Safety features: temperature sensor, emergency safety switch, limit switch - Safety rating: IP 54 - Declaration of conformity: CE Bwsdpfju R Urhex Agzji

Condition: like new (used), Year of construction: 2024, operating hours: 200 h, functionality: fully functional, input voltage: 400 V, type of input current: three-phase, total length: 2,700 mm, I offer a new machine for large format thermoplastic solutions for 3D printing. Control: Stäubli / Cead - Profinet full controll Robot: Stäubli TX200L - reach 2700 mm, load capacity 100kg Bsdsurvzrjpfx Agzswi Extruder: Cead E25 with a flow rate of 12kg/h Dryer VIZMATEC 100l plus automatic dosing for continuous production. G-CODE / NC code is used to generate the robot trajectory.

Condition: excellent (used), Zwick Type: BZ2.5/TN1S Zwick table testing machines Tensile strength measuring machine Area of application: Wide range of applications, from plastic and elastomer testing to paper, textile, foam and wire to component testing. Load frame: Max. test force FN in tension/compression direction 2.5 kN Height (h1) approx. 770 mm Width with electronic unit 320 mm Depth with electronic unit 414 mm Height of the work area h min ... h max: Traverse angle mounted upwards 227 ... 573 mm Traverse angle mounted rotated by 180° 57 ... 403 mm (each without connection bolt) Connection values: Electrical connection 115/230 V 4/2A-1PH/PE/N Power consumption 0.4 kVA Bwsdpjfnm Dqefx Agzsi Mains frequency 50/60 Hz 2.5 kN Condition: used Scope of delivery: (see image) (Changes and errors in the technical data, information are reserved!) We will be happy to answer any further questions you may have over the phone.