Used measuring systems for sale (290)

Condition: excellent (used), Mahr Mahr MarSurf CD 120 / CT120 Complete System For sale is a professional contour and surface measuring system from Mahr, consisting of several devices, accessories, calibration standards, and extensive training documentation. This is a high-quality laboratory or quality measurement system for precise analysis of surface geometry, contours, and measurement parameters. Main unit: Mahr MarSurf CD 120 (Contour Measuring System) CNC contour measuring instrument with vertical axis system Precision measuring module with stylus holder Granite measuring plate with guides Suitable for contour measurements on technical components Typical measuring ranges: Vertical (Z-axis): approx. 60–120 mm (model-dependent) Horizontal (X-axis): approx. 100–120 mm Extremely high accuracy due to granite base and backlash-free guides Control units: Mahr MidRange / MidRange CNC (Type MCP-22 / MCP-23) Control and operating unit for the axes Interface for measurement software (MarWin / MarSurf XC) Mahr ST 500 External control or sensor module (often for special probes) Software and Documentation Status MarSurf XC2 V. 3.01–03.4 MarSurf XC20 V. 5.00–10.1 MarWin v13.20-07 Operation manuals, training folders, training documents Measuring examples, diagrams, technical instructions This software is designed for evaluating contours, profiles, and surface parameters. Accessories / Measuring and Calibration Parts Stylus and probe arm sets Precision styluses of various shapes and lengths Replacement needles and mounting tools Stylus holder with protective case Calibration and reference pieces Mahr Contour 2 Block with reference sphere Calibration and parameter data For PCV, CD 120, LD 120 CDs and data carriers with parameters and software Transport and protective cases Several original cases with foam inserts Calibration seal/inspection sticker visible (valid until 2026) Typical voltage data for the Mahr MarSurf / MidRange / CT series MarSurf CD 120 (Contour measuring unit / axis drive) Supplied via control unit Internal usually: 24 V DC External power supply via MidRange control unit Mahr MidRange control unit (MCP-21 / MCP-22 / MCP-23) This device is the central power supply unit. Typical values: Primary: 230 V AC / 50-60 Hz Secondary: 24 V DC (regulated) Power consumption: approx. 40–80 W Mahr ST 500 Also connected to the MidRange system Powered by 24 V DC CT120 / Probe systems Cedpfx Abjx A Ur Rsbsaa Sensors operate at low voltage 5–24 V DC Supplied by the main unit (no separate power supply) Accessories, manual control units, interface boxes Usually 5 V or 24 V DC, depending on module Weight: approx. 65–73 kg Important note: "The table shown in the photos is not included in the sale." Condition: used Scope of delivery: (see photo) (Subject to change and errors in the technical data and specifications!) Further questions can be answered by phone.

Condition: excellent (used), manufacturer: GRÜN SYSTEMTECHNIK WETZLER including case We offer an original ATC measuring microscope, originally taken from a TRAUB TNA turning center. The unit is designed for installation in the automatic tool changer and can be used on various CNC machines with a suitable toolholder interface (size comparable to TRAUB TNA400 Key Features & Benefits: • Universal application: Suitable for any CNC machine with compatible toolholder interface. • Fast tool setup: Enables direct measurement of cutting edges, tool lengths, and radii inside the machine. • Process reliability: Tool wear can be identified immediately and corrected without removing the tool. • Precise referencing: Useful for checking zero points, bores, and fixtures directly in the setup. • Time savings: Eliminates the need for external presetting devices and reduces downtime. • Compact & robust design: Easy to integrate and operate within the tool changer system. Csdpsx Dmr Eofx Abbjaa This ATC measuring microscope turns your CNC machine into a precise measuring station, helping you achieve higher accuracy, shorter setup times, and improved process reliability.

Condition: ready for operation (used), Dear Sir or Madam, We hereby offer you the following device for sale: Keyence XM-2000 coordinate measuring system. The machine is sold with the equipment documented in the photos and specified in the advertisement text. Location: 40764 Langenfeld ATTENTION! The device originates from an insolvency. We are auctioning it off to the highest bidder on behalf of the creditor/bank. Cajdpfxsxzn E Us Abbja This is a closed auction. We do not provide any information about the current highest bid. Your bid becomes binding upon receipt by email. Please send us your binding bid by 10 a.m. on 7 December 2025. After the auction ends, you will be informed of the auction result within 72 hours.

Condition: used, Year of construction: 2008, dimension of workpiece 2400 mm Cjdpfox Dda Tjx Abbjaa voltage 26,8 V total power requirement 26,8 kW weight of the machine ca. 0,040 t

Condition: used, functionality: unexamined, machine/vehicle number: TDS 784C, input voltage: 220 V, Tektronix TDS 784C Oscilloscope Cajdpfx Abjx A Arljbja Manufacturer: Tektronix Model: TDS784C

Condition: ready for operation (used), 1 set (5 pieces) of micrometers, in wooden case Cedpsx Anp Nefx Abbjaa Sizes: 0 - 25, 25 - 50, 50 - 75, 75 - 100, 100 - 125, 125 - 150 mm

Condition: excellent (used), Quality Vision OGP SmartScope FLASH CNC 300 For sale is an OGP SmartScope FLASH CNC 300, a high-quality multi-sensor coordinate measuring machine for precise 2D/3D measurement tasks. This system comes from industrial use and is ideally suited for quality assurance, production, toolmaking, and laboratory applications. Description: The FLASH CNC 300 is a CNC-controlled optical measuring system with optional laser and touch probe technology. It enables highly precise measurement of mechanical components – e.g. diameters, heights, distances, contours, and geometric elements. Thanks to its video technology, motorized zoom optics, and multi-sensor-capable architecture, it is particularly versatile in application. Technical Data: Model: SmartScope FLASH CNC 300 Manufacturer: Optical Gaging Products / Quality Vision International (USA) Measuring range (XYZ): 300 × 300 × 250 mm Max. workpiece weight: up to 30 kg System weight: approx. 160 kg Power supply: 230 V~, 50/60 Hz, 2.5 A Shipping weight (packed): approx. 340 kg Measuring Methods & Equipment: Optical video system with motorized 12:1 AccuCentric® zoom Automatic zoom calibration for highest repeatability LED illumination: - Transmitted light (profile) - Coaxial incident light - SmartRing™ LED ring light Optionally usable sensors: - Laser (TTL laser) - Touch probe / scanning probe - Microprobes / height measurement Casdpexz A Evefx Abbsa Supported software (model-dependent): Measure-X, ZONE3, etc. Fields of Application: - Quality assurance - Batch and single part inspection - Measurement of plastic, metal, and milled parts - Precision optics, mold, and tool measurement - Laboratory, production, and research Condition: used Scope of supply: (see image) (Specifications are subject to change and errors excepted!) We would be happy to answer further questions for you by phone.

Condition: excellent (used), functionality: fully functional, We offer a Keyence stripe light measurement device. Series VL 350, including PC, software, and calibration disc. This allows for stand-alone operation. Strengths: • Contactless measurement: As the system is optical and does not use a mechanical touch probe, it is ideal for measuring delicate or sensitive workpieces with fragile coatings (no deformation caused by a measurement probe). > High accuracy & repeatability: Measurement accuracy of ±10 µm and repeatability of 2 µm make it suitable for a wide range of industrial quality control applications. > Flexible measuring range: Capable of measuring larger components (up to Ø 300 mm × H 200 mm) as well as small detailed parts (Ø 70 mm × H 50 mm) — with easy switching between low and high magnification. > Versatile application: The rotatable and tiltable table enables measurement of various geometries and complex workpieces. The device is suitable for: Cajdpjx Dcg Sofx Abboa > Quality control and 3D inspection of parts in manufacturing — for example, workpieces made from plastic or metal > Measurement and reverse engineering of complex geometries where contactless measurement is advantageous > Areas where high precision and repeatability are essential — for evaluating form and positional tolerances > Digitizing components with STL output for subsequent 3D printing. Original packaging is available – courier delivery can be arranged for an additional fee. Transport and loading can be organized throughout Europe at extra cost upon request. Prices are subject to VAT. Inspection possible by appointment. Please contact us; our team looks forward to assisting you. Trade-in or exchange possible! Machinery Purchase / Sales PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINERY AND MORE. Looking for a high-quality yet affordable metalworking machine for your production? Or are you looking to sell yours? For further information or to get in touch, please visit our website.

Condition: good (used), functionality: fully functional, machine/vehicle number: 66259, total width: 600 mm, total length: 800 mm, total height: 900 mm, overall weight: 500 kg, Contour measuring instrument Incl. granite measuring plate Plate dimensions: 670 x 450 mm Incl. various measuring tools NOTES ON COLLECTION: Collection must take place strictly between December 10 and 12 Cjdpfexnkb Sjx Abboaa FCA Winterlingen, loaded onto truck

Condition: excellent (used), Micrometer make Hommel Precision Measuring range 175 - 200 mm diameter Cedpfx Abstt Nugeboaa (2852) Test gauge in wooden storage case

Condition: used, functionality: fully functional, type of input current: AC, input voltage: 240 V, Equipment: type plate available, Used Keyence Digital Microscope VHX 900/950F Set in Flightcase Manufacturer: Keyence Model: VHX 900/950F Voltage: 100-240 VAC (50/60 Hz) Set consists of: Caedpsv A Uptsfx Abbea – Digital microscope + power cable – Digital camera – Lens (Keyence VH-Z20R) – Camera holder + mount – Keyboard + mouse – Console controller – Flightcase

Condition: excellent (used), Year of construction: 1998, Contour measuring device / roughness measuring device Tester T 8000, granite plate Wave System 630 x 500 x 100 mm, Waveline 60 Advanced, base unit Wavelift 400, base tilting unit 60 for Wavelift, probe arm TA 20. UPGRADED in 2010 !!! Cedpfxjxhdvio Abbsaa

Condition: used, Shimadzu Type: AG-X plus 20kN-50kN +750mm Dimensions: W 1206 x D 765 x H 2920 mm Technical specifications: Fmax: 50 kN Speed: 0.00005~1500 mm/min Accuracy: ±0.1 % Csdpfsxywh Nex Abboaa JIS B7742 Class 0.5, ASTM E2658 Class A Crosshead-table distance (mm)(tensile stroke)*3: 215 to 1940 (20 kN: 0 to 1535 mm, 50 kN: 0 to 1475 mm) Possible test width: 600 mm Frame stiffness: 180 kN/mm 710 kg 200 V 4.5kVA/15 A + Accessories as shown Condition: used Scope of delivery: (see picture) (Specifications and data subject to change and errors!) If you have further questions, we will be happy to answer them by phone.

Condition: excellent (used), Year of construction: 2010, 1" image sensor, 6.6 megapixels, CMOS Codpsxllfgjfx Abbsaa Double telecentric lens Z-axis travel distance 30 mm Z-stage maximum load 3 kg

Condition: excellent (used), Here we offer you a FRT MicroSpy Mobile. Device name: FRT MicroSpy Mobile Art. No. MSP 105 00 Device number: MSP1033 FRT MicroSpy Mobile Portable optical profilometer for non-destructive 3D surface measurements directly on the component. The portability of the MicroSpy Mobile makes it ideal for mobile use on heavy machinery, vehicles, rollers, glass, etc. machines, vehicles, rollers, glass panes or other large components. High-resolution and non-destructive measurements of important surface characteristics such as roughness, contour, topography, layer thickness, wear, contact ratio or volume. Smaller samples can be measured directly on the measuring table Can be used on large components and machines Excellent resolution values Excellent reproducibility Non-destructive measurement Handles and adjustable support feet Low weight (approx. 5 kg) FRT Technical Specifications: Device: MicroSpy Mobile xy-relief 50 x 50 mm² xy-table Type: compact XY cross table with open frame Bearing: mechanical cross roller guide Drive: DC motor with recirculating ball screw Csdpfx Asg Sr D Hsbbeaa Travel (measuring range XY): 50 x 50 mm² (or 20 x 20 mm² with CWL 3mm) Position measuring system: Rotary encoder Measuring system resolution: 0.25 µm Repeat accuracy XY: < ± 1 µm Table runout (per axis): < 2 µm / 50 mm of which not reproducible ): < 0.5 µm perpendicularity XY: < 4 µm / 50 mm z-axis, motorized: Type Position r Drive Travel Position measuring system Measuring system resolution Rope sc

Condition: good (used), Heinzinger Here we offer you a battery module tester. Description: Highly dynamic test bench energy system Bidirectional DC power supply with active energy recovery, liquid-cooled Voltage [max]: 20 - 600 V adjustable Current [max]: ± 500 A adjustable System power [max]: ± 160,000 W Mains connection (3/N/PE): 3x400V ±10% 47 ... 63Hz Software: Battery simulation software for load change-optimized control Dimensions (W/H/D): 1800/2330/800 mm Type: ERS 600-500/160 Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information are subject to change!) Caodpfxsq Nzwao Abbja We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), Here we offer you an et ETSYSTEM Electronic Load GPIB. 32615A AC & DC Electronic Load GPIB/RS232 300V, 108A, 10800VA The 3260A series is a 300V high power AC and DC load in one unit and provides an ideal test solution for UPS, AVR and D/A inverters, especially for DUTs with step or square waveforms Each high power series AC&DC load has its own control and display panel and 5-state recall/memory, allowing for more efficient load setup Adjustable power factor setting (PF, range: 1, 0.85 ~ -0.85) expands the simulation of the test environment Built-in GO/NG gauge test function provides short test result diagnosis for production and QC test throughput Features Voltage, current, wattage and VA variable display. CC, Linear CC, CR and Crest Factor modes. GPIB/RS232 interface and 5 status recall/memory. Power factor (PF) adjustable: 1, 0.85 ~ -0.85. Cjdpfx Absm Tvyxjbjaa Upper/lower threshold capability. Protection against V, I, W and ℃. Dual 4 1/2 meter display for voltage, current, watts and VA. Suitable for sine, square and step waves. Width 600 mm Height 1506 mm Depth 600 mm 196kg Type: 32615A AC & DC Electronic Load Condition: used / used Scope of delivery: (See picture) (Changes and errors in the technical data, specifications are reserved!) Further questions we can answer on the phone for you.

Condition: good (used), Keyence Type: VR-6200 + VR-6000 Technical data: Measurable XY area 300 mm × 150 mm *2 Object table XY stroke 278 mm × 134 mm Z stroke 69 mm Load capacity 4.5 kg Working distance 75 mm Image capture device 4 megapixel CMOS, B/W Macro mode: Magnification (relative to a 15-inch monitor) 12× Horizontal 24.0 mm Vertical 18.0 mm Magnification (relative to a 15-inch monitor) 25× Horizontal 12.0 mm Vertical 9.0 mm Magnification (relative to a 15-inch monitor) 38× Horizontal 8.0 mm Vertical 6.0 mm Magnification (based on a 15-inch monitor) 50× Horizontal 6.0 mm Vertical 4.5 mm Micro mode: Magnification (based on a 15-inch monitor) 40× Horizontal 7.6 mm Vertical 5.7 mm Codpfx Aber Dby Isboaa Magnification (based on a 15-inch monitor) 80× Horizontal 3.8 mm Vertical 2.9 mm Magnification (based on a 15-inch monitor) 120× Horizontal 2.5 mm Vertical 1.9 mm Magnification (based on a 15-inch monitor) 160× Horizontal 1.9 mm Vertical 1.4 mm Zoom 1× to 4× Display resolution 0.1 μm Height measurement range Without Image composition in Z Macro mode: 10 mm Micro mode: 1 mm With image composition in Z Macro mode: 50 mm Micro mode: 30 mm Repeatability (σ) Without image composition in Z 0.4 μm *1 With image composition in Z 1.0 μm *1 Measurement accuracy Without image composition in Z ±2.5 μm *1 With image composition in Z ±4.0 μm *1 Only 50 operating hours! With software CD without PC! Condition: (as new!) For further technical information, please contact the manufacturer. Scope of delivery: (As shown!) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: good (used), Here we offer you a Panasonic industrial image processing ImageChecker P400 with vision software's. consisting of the following components: 2 x ImageChecker P400 1 x vision P400 software Caedpfxodpizlo Abbja 9 x ANPC 837 D double speed mega pixel camera and further accessories see pictures! New in the sense of unused! Type: Panasonic ImageChecker P400 Condition: new / new Scope of delivery: (See image) (Errors and omissions in the technical data, information are reserved!) We can answer questions on the phone for you. Written order possible by email or fax

Condition: good (used), Heinzinger Type: ERS 600-500/160 Description: Battery module tester Highly dynamic test bench energy system Bidirectional DC power supply with active energy recovery, liquid-cooled Voltage [max]: 20 - 600 V adjustable Current per channel [max]: ± 500 A adjustable System power [max]: ± 250,000 W Mains connection (3/N/PE): 3x400V ±10% 47 ... 63Hz Software: Battery simulation software for load change-optimized control Dimensions (W/H/D): 2400/2330/800 mm Condition: used Scope of delivery: (See picture) Casdpfsq Nzwhox Abbea (Changes and errors in the technical data, information are reserved!) We will be happy to answer any further questions you may have over the phone.

Condition: excellent (used), Keyence Here we offer you a 3D profilometer. Technical data: Viewing and measuring range: Horizontal: mm 24.0 12.0 8.0 6.0 7.6 3.8 2.5 1.9 Vertical: mm 18,0 9,0 6,0 4,5 5,7 2,9 1,9 1,4 Measuring resolution 0.1 μm : Height measurement: Height measuring range Without image composition in Z : 10 mm 1 mm With image composition in Z : 50 mm 30 mm Repeatability (σ)*1 Without image composition in Z : 0.4 µm With image composition in Z : 1.0 µm Width measurement: Measurement accuracy*1 Without image composition in Z : ±2.5 μm With image composition in Z : ±4.0 μm Repeatability (σ) *1 1 μm 0.5 μm Measurement accuracy*1 ±5 μm ±2 μm XY stroke 184x88mm Z stroke 73mm Incl. VR-5000 control unit + software with licenses Type: VR-5200 + VR-5000 Sale ex location!! Condition: fully functional + no traces of use For more technical information, please contact the manufacturer. Scope of delivery: (As shown) (Changes and errors in the technical data, specifications are reserved!) Codpfxskvnthj Abbjaa Further questions we can answer on the phone for you.

Condition: excellent (used), Rexcan Type: 3D scanner Rexcan CS2 + 3-axis swivel table TA 300+ Technical data: Caodpfx Abovt Sydjbja 6.0 MP camera 1 lens set FOV:125,250,500 V:125,250,500 B:95,195,380 H:80,155,320 SPA:0.036, 0.072, 0.145 G:0.01-0.015, 0.02, 0.03 Triangulation angle = 25 degrees PC and software included (screen not included) Scan software: eZScan 2017 Geomagics Control X Version 2018.1.2 Scanner “Rexcon CS2” Rotary table “TA300+” Optics set 125, 250, 500 Calibration plate for all three optics Clamping set Holder for small parts Cabinet on wheels + adjustable with integrated spirit level Condition: used Scope of delivery: (See picture) (Changes and errors in the technical data, information is subject to change!) We will be happy to answer any further questions you may have over the phone.

Condition: used, Huda Technology HUD-G809 Drop Shock Test System The system is also suitable for testing batteries. Max load: 100 kg Caodpfx Abjxmiiljbja Table size: 500 mm x 600 mm Peak impact acceleration range (half-sine wave): 150 - 6000 m/s² Pulse duration (half-sine wave): 0.5 - 30 ms If the pulse duration is less than or equal to 3 ms, the tolerance for peak acceleration is ±20%; the tolerance for pulse duration is ±15%. If the pulse duration is greater than 3 ms, the tolerance for the waveform should comply with the range specified in the standard. Velocity tolerance: ±15% Hydraulic brake prevents secondary impact. Overall table dimensions: 1000 x 750 x 2450 mm Weight: 3600 kg Power consumption: 5.5 KVA 380V ±10% AC 50 Hz Condition: used (We reserve the right to make changes and correct typing errors in technical data and specifications!) If you have any other questions, we would be happy to answer them by phone.

Condition: excellent (used), Mahr Cjdpswlhwnjfx Abbeaa Type: MarSurf GD 140 BG 22 Product Information: The MarSurf GD 140 is a high-precision roughness and waviness measuring station from Mahr, designed for use in production metrology and in the measuring room. It sets new standards in surface metrology with its high speed, reliability, and flexibility. Product Features: Multifunctional: Measures roughness, waviness, and profile of workpieces. Location: Can be used in the measuring room or in close proximity to production. Software: Control via user-friendly MarWin software: EasyRoughness MarWin Software Version: V12.20-06 SP1 Areas of Application: Industry: Mechanical Engineering Typical Measurement Objects Bearings, threads, threaded rods, ball screws, shafts, gear racks Industry: Production Metrology Typical Measurement Objects Contour Measurement in Semi-Automatic Processes Industry: Automotive Industry Typical Measurement Objects Steering, braking systems, transmissions, crankshafts, camshafts, cylinder heads Industry: Medical Technology Typical Measurement Objects Contours of hip and knee endoprostheses, medical screws, and dental implants Technical Specifications – MarSurf GD 140 Feature Value / Description Resolution – Measuring Range 1 / 2.0 nm Resolution – Measuring Range 2 / 0.2 nm Start of Traverse Length (X) 0.1 mm End of Traverse Length (X) 140.0 mm Traverse Length (Lt) 0.1 – 140 mm Guide deviation 0.20 µm / 60 mm 0.40 µm / 140 mm Measuring force 0.7 mN Measuring speed 0.02 mm/s to 10 mm/s Positioning speed (X) 0.02 – 200 mm/s Positioning speed (Z) 0.02 – 50 mm/s Probe system: Roughness probe system (skidless) – without probe base Probe arm lengths 45 mm (×1) 67.5 mm (×1.5) 90 mm (×2) 112.5 mm (×2.5) 135 mm (×3) Measuring range (depending on probe length) ±250 µm (with 45 mm probe arm) ±750 µm (with 135 mm) Probe arm) Technical specifications – Dimensions: Dimensions (L × W × H) Length: 780 mm, Width: 535 mm, Height: 1240 mm Maximum workpiece weight: 90 kg Additional functions Manual TY adjustment (e.g., for lateral alignment) Total weight (gross): 196 kg Condition: Used Scope of delivery: (See image) (Subject to changes and errors in the technical specifications, information is subject to change!) We are happy to answer any further questions you may have over the phone.

Condition: excellent (used), Keyence Model: VR-5200 Type: Measuring Head Light Sources Viewing Light Source: LED Ring Light (red, blue, green) Measurement Light Source: White LED Control Unit: VR-5000 Viewing and Measurement Range Macro Mode Magnification (based on a 15-inch monitor) 12×: Horizontal 24.0 mm Vertical 18.0 mm Magnification (based on a 15-inch monitor) 25×: Horizontal 12.0 mm Vertical 9.0 mm Magnification (based on a 15-inch monitor) 38× Horizontal 8.0 mm Vertical 6.0 mm Magnification (based on a 15-inch monitor) 50× Horizontal 6.0 mm Vertical 4.5 mm Cjdpfxowc Sxds Abbjaa Micro Mode Magnification (based on a 15-inch monitor) 40× Horizontal 7.6 mm Vertical 5.7 mm Magnification (based on a 15-inch monitor) 80× Horizontal 3.8 mm Vertical 2.9 mm Magnification (based on a 15-inch monitor) 120× Horizontal 2.5 mm Vertical 1.9 mm Magnification (based on a 15-inch monitor) 160× Horizontal 1.9 mm Vertical 1.4 mm Zoom 1× to 4× Height Measurement Measurement Resolution 0.1 µm Height Measurement Range Without Z-Compositing Macro Mode: 10 mm Micro Mode: 1 mm With Z-Compositing Macro Mode: 50 mm Micro Mode: 30 mm Repeatability (σ) Without image stitching in Z 0.4 µm With image stitching in Z 1.0 µm Measurement accuracy Without image stitching in Z ±2.5 µm With image stitching in Z ±4.0 µm Width measurement Repeatability (σ) Macro mode: 1 µm Micro mode: 0.5 µm Measurement accuracy Macro mode: ±5 µm Micro mode: ±2 µm Image stitching Fully automatic measurement (automatic XY control + automatic Z focus), Automatic assignment, automatic area setup Measurable XY area 206 x 104 mm Stage XY travel 184 × 88 mm (motorized) Z travel 73 mm (motorized) Load capacity 4.5 kg Working distance 75 mm Image pickup element 4-megapixel CMOS, B/W Transmitter lens Dual telecentric lens x 2 Receiver lens Dual telecentric lens Data processing Dedicated PC according to KEYENCE specifications (Operating system: Windows 11 Pro) Power supply Voltage 100 to 240 V AC, 50/60 Hz Power consumption Max. 200 VA Environmental resistance Ambient temperature 15 to 30 °C Relative humidity 20 to 80% RH (no condensation) Weight Approx. 28 kg (weight of the measurement unit only: approx. 11 kg) Distance extension stage Viewing software VR-5000 Version 3.3.5.75 Image composition module VR-H3J Creates a single large image from a series of images captured with the viewing software. You see color images. Analysis Expansion Module VR-H3CA Extends the functionality of the analysis software. Can perform measurement comparison and 3D CAD measurement comparison. Condition: Used Scope of delivery: (as shown) (Subject to change and errors in the technical specifications, information is subject to change!) We are happy to answer any further questions over the phone.