Heavy-duty trailers

WMT D15/10,0 x 2,45

Condition: excellent (used), Year of construction: 2008, overall weight: 1,195 kg, volume flow: 7.25 m³/h, operating pressure: 13 bar, input voltage: 400 V, ATLAS COPCO GA 37 VSD ff screw compressor Variable speed, (inverter) With refrigerant dryer Itjdet Hdh Nopfx Aa Ejr 37 kW motor Capacity 7.25 m3/min Pressure 13 bar Mileage 13200 hours The compressor is fully functional.

Condition: used, Cut-to-length line Delta-Alcos 72”x0.5”x60,000Lb (A3770) Make: Delta / Alcos Material Width: 36" - 72" Thickness Capacity: .048" - .530" Weight Capacity: 60,000Lbs Coil ID: 16" - 24" Coil OD: 72" Yield Strength: 50,000PSI Direction: Right to Left Coil Storage Conveyor Entry Coil Car Ijdpfx Aaoixqg Nj Ejtr Hydraulic Lift and Traverse Cone Uncoiler DC Motorized Brake Sliding Base Wichita Cooled Brake Powered Hold-Down Roll Hydraulic Peeling Table Powered In & Out Set of Driven Pinch Rolls Delta Corrective Plate 4-Hi Leveler Number of Work Rolls: 9 Work Roll Diameter: 8" Work Roll Width: 82" Powered Up & Down Back-Up Flights DC Motor & Drive Delta Corrective 4-Hi Leveler Number of Work Rolls: 19 Work Roll Diameter: 4" Work Roll Width: 82" Motorized Back-Up Flights Powered Work Roll Adjustment DC Motor & Drive Alcos Mechanical Shear Down Cut Shear Driven Entry Pinch Rolls Pneumatic Clutch & Brake AC Motor Drive Alcos Drop Type Stacker 40' Sheet Length Driven Exit & End Conveyrors Touch Screen Digital Panel Operator Push Botton Station Digital Read Outs Hydraulics, Electrics, Controls, Presently Installed

Condition: good (used), Year of construction: 1998, Concrete mixing plant Imer Betomatik 508 -year of construction 1998 -Power approx. 10 cbm/h -Cement silo 40 t -mixing portal with mixer and control -scraper arm with chain for 2 kinds of gravel Itedpfx Asm Uyvkja Ejr Reference picture

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm - 45º: 716x304mm Itedohzbipspfx Aa Ejr - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: used, Hydraulic Guillotine Shear STEINER Type HTS 30/20 R Machine No. 315 Year of manufacture: 1982 Cutting length: 3050 mm Cutting thickness: 20 mm Backgauge: 800 mm, motorized control Motor power: approx. 30 kW Power supply: 400 Volt, 50 Hz - Backgauge with ELGO position control - Backgauge adjustment via ball screw spindles - SICK safety light curtain at the front for access protection - 3 material support arms with ball rollers - Electric foot switch - Spare blade - Oil cooler with air heat exchanger - Extremely heavy-duty machine in very robust construction Base machine dimensions L x W x H: 4650 x 2610 x 3200 mm Base machine weight: 27,000 kg Transport space required (base machine) L x W x H: 4650 x 2610 x 3200 mm Transport space required (additional) L x W x H: 3500 x 2450 x 1400 mm Itsdpfed Hxx Aox Aa Eer Total weight: 27,000 kg Good condition Machine can be inspected at our warehouse in 37235 Hessisch Lichtenau. Test cuts possible.

Year of construction: 1985, condition: ready for operation (used), Table dimension: 1435x460mm, T-groove number/ width/ distance: 5/ 16/ 80mm, controls: TNCi-120, length: 1435mm, width: 2330mm, height: 1648mm, weight: 3,1t, with documentation, accessories are available, no defects known, an inspection is possible. Iodpfxjlbmupj Aa Estr

Condition: new, Year of construction: 2025, load capacity: 2,000 kg, Protec KT 2000 HV, Hydraulically height adjustable Load 2000 KG Manual remote control with digital display Double foot remote control Height approx. min. 800mm tilted to middle , height max. 1400mm Height min. horizontal 1000mm diameter faceplate 1200mm Tilt angle min. 135 Speed 0,05 to 0,9 rpm. Motor power 3 KW Itodpfx Aaoncfvho Eor

Condition: excellent (used), Several 150 m³ steel storage tanks (extinguishing water tanks) located underground Volume: 150,000 litres diameter: approx. 3.000 mm length: approx. 22.500 mm Weight: approx. 28,000 kg The tanks are converted to underground extinguishing water tanks according to DIN 14230: The tank has an extinguishing water suction connection according to DIN 14244 with a mounted fire brigade coupling/fixed coupling A according to DIN 14319 in the design form B without gauge connection. Furthermore, the tank has a venting flange connection in NW/DN 100 with cap in a total length of approx. 1,300 mm suitable for 800 mm ground cover and 500 mm above ground. - The tank is emptied, cleaned and has been provided with a bitumen exterior coating by us at the factory. - if required, we can provide the tank with a full bitumen-based interior coating (against corrosion) or epoxy resin interior coating A cost-effective delivery with our own truck is possible. Simply inform us of the delivery location, you will then immediately receive the exact freight costs. An inspection is possible at any time by prior appointment. If you need any further information, just give us a call or send us an e-mail to b.barth (a) barth-tank. de Ijdpfofnh Tgex Aa Estr

Condition: new, DESCRIPTION DM100 Z2C - performs edge rounding and removes sharp burrs from both the inner and outer edges of steel, stainless steel or aluminium parts after laser, shear or punch cutting of metal parts from 50 x 50 mm up to 1100 x 100 mm in size. Ekdjtxp The 1st station processes the products through a contact roller (approx. 55° shore) with an abrasive belt and removes strong burrs in the first step. The 2nd station processes the products with 2 counter-rotating cross belts each from below and from above. The cross belts round off the parts to be machined on both the inner and outer edges. A big advantage is also the deburring of products with surface protection foil, because only the edges are processed without damaging the foil. Technical data - DM1100 Z2C: Working capacity (Ø mm) 1100x100 No. of belt stations (Z) 1 No. of cross belt stations 2 Isdpfed Ixadex Aa Ejtr Abrasive belt, dimensions (mm) 1100x2200 Abrasive belt speed (m/s) 8-22 Cross belt speed (m/s) 2-8 Feed speed (m/s) 0.6-3.2 Sanding belt motor per head (kW) 18.5 Cross belt motor (kW) (2x) 3 Feed motor (kW) (3x) 0.18 Total power (kW) 33 Power consumption (A) 62 Rod suction connection per head (Ø mm) 150+185 Dimensions (mm) 3600x2330x2350 Weight (kg) 5000

Condition: as good as new (ex-display), functionality: fully functional, type of cooling: water, FRONIUS TPS 5000 ✅ Scope of delivery: ➤Fronius TPS 5000 power source (500A TRANS PULS SYNERGIC) ➤Fronius FK 4000 ➤Fronius VR 4000 wire feeder unit ➤Fronius standard intermediate hose package from 1.5m ➤Fronius trolley ➤Fronius hose package ➤Ground cable 3-4m ➤Pressure regulator This device can weld almost all materials, including aluminum, steel, and V2A. It features touch wire programs and is also suitable for MIG brazing (Cusi), which is frequently used in the sheet metal industry. Additional options and applications: This TPS series can be easily connected to a robot. All you need is an interface and the appropriate hose package. We also offer the optional RCU 5000i control panel, which allows you to create and import characteristic curves to further expand the functions of the TPS device. ---- IMMEDIATELY AVAILABLE PROPER INVOICE A viewing is possible in Austria in Vienna, 1230! ✔ Insured shipping on a pallet is no problem! ✔ ✅Questions✅Questions✅Questions: ✅Questions✅Questions✅ Questions✅ ►►►What is the condition of the device? To explain, we buy like-new used devices, disassemble them, check everything, replace wear parts if necessary, and only then, after successful test welding, is the device released for sale. "All" devices are clean and have neither burn holes in the displays nor countless burn holes or dents scattered throughout the device! You are buying an item from us that is also worth seeing and doesn't look completely finished! ►►►Do we receive an invoice when we purchase from you? Yes, we provide a proper invoice. If you have a valid VAT ID, we can issue a net invoice if the requirements for intra-community delivery within the EU are met. Isdewbh Ifjpfx Aa Estr ►►►What payment options are available? Advance payment or cash upon personal pickup ►►►Is insured shipping possible? Yes, we will be happy to send you the purchased set well packaged and insured on a Euro pallet. ►►►Is there a warranty? We sell the machines at one-third the original price and unfortunately do not have the flexibility to offer a warranty. You are welcome to test the devices on site and pay in cash. ►►►Why buy from us? We are experts in this Fronius welding machine series and always have 60-80 devices in stock – exclusively Fronius, no other manufacturers! We are experts in these devices and don't sell anything we don't know about.