Grinding machine

Tschudin HTG 310

Condition: excellent (used), Year of construction: 1994, center height: 100 mm, grinding length: 380 mm, total width: 1,500 mm, total length: 1,300 mm, total height: 1,350 mm, grinding diameter: 200 mm, spindle speed (max.): 1,800 rpm, overall weight: 2,100 kg, pivoting range: 10 °, Centre height: 100mm Grinding Ø: 200mm Grinding length: 380mm Grinding stone dimensions:300 x 50 x 127mm Grinding stone speeds: 1800Rpm Table inclasement: 10° Klodjyu Nqgepfx Amrju Tailstock: 4Mk Length: 1300mm Width: 1500mm Height: 1350mm Weight: 2100kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1963, Technical details: max. wheel diameter: 900 mm max. module: 10 weight of the machine ca.: 8200 kos. hob dia. - max.: 190 mm cutter length max.: 320 mm milling spindle speeds (infinitely variable): 13-80 U/min workpiece length - max.: 750 mm max. workpiece diameter: 150 mm Counter holder milling mandrel is missing Ksdpfx Aevkpu Hemrelu *

Condition: new, Year of construction: 2026, functionality: fully functional, Data Machine type: HTG 310 Workhead: MK5 Tailstock: MK3 Center height: 100 mm Center width: 380 mm Grinding length: 380 mm Grinding wheel: 350 x 50 x 127 mm Condition The machine is currently in a used (not reconditioned) condition. All wear parts of the machine will be replaced, including the feed spindle in the X and Z axis. All components will be returned to as-new condition. After the overhaul, the machine is comparable to a new machine. Kledpfecgkurjx Amrsu Geometry The machine will be completely dismantled down to the guides. Before the geometry of the individual tables and components can be restored, both guides of the Z and X axis are manually scraped and restored to as-new condition. Upon completion, the machine is issued with a test certificate according to the manufacturer’s specification.

Condition: good (used), Year of construction: 2000, 20000 rpm, tool measurement on table will come, Parts shown by hand not come. Kedpsr Urm Sefx Amrolu

Condition: like new (used), Center height over bed: 330 mm, max turning diameter over carriage: 408 mm, max turning diameter over bed: 640 mm, max turning diameter in gap: 899 mm, distance between centers: 2000 mm, variable spindle speed, rpm: 18-1500, spindle bore diameter: 105 mm, spindle nose: ASA 11”, tailstock: MT5, quill diameter: 90 mm, travel: 250 mm. cross slide travel: 275 mm. main motor: 15 hp. machine weight: 3450 kg. Kjdpsx Dikkjfx Amrslu

Condition: new, Year of construction: 2024, carrying capacity per cantilever arm: 500 kg, shelf height: 3,200 mm, total length: 2,100 mm, total height: 3,200 mm, axle spacing: 1,000 mm, load capacity per stand: 2,500 kg, Cantilever rack in hot-dip galvanized design: Scope of delivery: 3 rack stands, height 3.2 m with base section, 1.8 m usable depth (2 m total depth) 12 cantilevers with 1.8 m usable depth (for chipboard with approx. 2.1 m depth) Longitudinal and diagonal struts for 4 m rack length (distance 1.3 m) Fastening material (screws, nuts and washers) Net price: €2,490.00 plus VAT Detailed description: - Stable steel construction made of IPE profiles (screw system) - Rack height 3,200 mm - Load capacity per stand 2,500 kg - Base section and cantilevers with 1,800 mm usable depth Kodeqt Dmyspfx Amrolu - (for 2,100 mm chipboard depth) - Cantilevers height adjustable in 100 mm increments - 4 screwable screws per stand Cantilever arms, standard (= 5 storage levels) - Load capacity per cantilever arm 500 kg - Including longitudinal and diagonal braces for 1,000 mm spacing - Shelf length = 2,100 mm - Including fastening material (without ground anchors) - With assembly instructions and load plates C4 in accordance with DIN standard - Made in Germany - Short delivery time Our cantilever racks are produced exclusively in Germany. We offer reliable freight with registration before delivery. The material is sensibly packed to enable easy unloading. Delivery for stock items can take place in approx. 1 week after receipt of the order. When installed outdoors, the load-bearing capacity is reduced by the wind and snow load. The subsurface must be made of concrete, level and dowel-capable and must be able to bear the loads. The condition of the soil and load-bearing capacity as well as any official permits required must be checked and guaranteed by the customer. The shelf supports must be anchored to the floor on site; anchoring to the wall is not necessary and not recommended. According to the trade association, it is recommended that the shelf supports on the top storage level have a projection of at least 500 mm above the top edge of the supports.

Condition: new, - Shaft diameter 50 mm - The upper roller is hydraulically moved - Three rollers are driven - Digital display - Can be used horizontally/vertically - Foot switch - Emergency stop Ksdpfx Asgg N Twjmrelu - Documentation - 400 V

Condition: ready for operation (used), A surface grinding machine ELB-Schliff with position display is available. Magnetic chuck dimensions X/Y: 900mm/450mm, grinding length: 900mm, grinding width: 450mm. Documentation available. An on-site inspection is possible. Klsdpfx Aoya Hw Ijmrju

Condition: used, Year of construction: 1990, grinding length 1500 mm grinding width 550 mm workpiece height 400/450 mm table-size 1900 x 450 mm mm table speeds 1 - 25 m/min cross feed autom. 0 - 60 mm/Hub grinding wheel size 400 x 100 x 127 mm grinding spindle speed 1400/2800 U/min total power requirement 15 kW voltage 380 V weight of the machine ca. 5 t Machine was reconditioned and modernized in 2015 with modern control. Klodpfx Aewlviromreu Machine has cooling arrangement, auto. vert. feed, dressing arrangement and wheel flanges.

Condition: used, CNC cycle controlled lathe HARRISON type Alpha 400 Plus Machine No. P30180/150 Year of construction 1998 center distance 1250 mm turning diameter over bed 400 mm center height 200 mm Swing diameter over cross slide 245 mm Swing diameter in the bend 585 mm bed width 313 mm face travel (X-axis) 250 mm Tailstock spindle diameter 73 mm Tailstock quill stroke 140 mm Tailstock quill mount MK 5 spindle bore 54 mm spindle head size Camlock D1 size 6 Spindle speed 20-2500 rpm. Spindle speed range (stage 1) 15-275 rpm. Spindle speed range (stage 2) 35-795 rpm. Spindle speed range (level 3) 110-2500 rpm. Feed rate X and Z 0.03 - 0.6 mm/rev. Rapid traverse speed X axis max. 2000 mm/min. Rapid traverse speed Z-axis max. 4000 mm/min. Threading function Metric / Inch / Diametral / Module Spindle drive power 7.5 KW Mains connection 400 Volt, 50 Hz, 23,5 kVA - cycle control Harrison Alpha / GE FANUC - language in French (France) - automatic gear range shifting in 3 steps (15-275, 35-795, 110-2500 rpm.) - electronic handwheels with different transmission ratios (1/10/100) Kedsh Hvk Aspfx Amrelu - 3-jaw face spiral lathe chuck FORKARDT Ø 250 mm type CSN, 1 set of soft top jaws - quick-change tool holder MULTIFIX size B with 2 inserts - 1 piece of centering point running with the tool - 1 piece quick-action drill chuck RÖHM, 3-16 mm - hinged lathe chuck guard - hinged working area protection doors - chip tray with coolant device under the machine bed - Switch cabinet fixed to the machine - Interface RS 232 Space requirement L x W x H 2600 x 1450 x 1550 mm weight 1950 kg good condition