Suction excavator

SAUGBAGGER Z243

Condition: good (used), functionality: fully functional, Year of construction: 2012, operating hours: 20,200 h, load capacity: 5,500 kg, fuel type: gas, Equipment: clamp, gripper hydraulics, For sale is a Hyster S 5.5FT gas-powered forklift. The forklift is fully functional and in good condition. Not offered with forks as shown, but with a Mayer paper roll clamp with rotary hydraulics from 2005 (last photo). Technical specifications: Year of manufacture: 2012 Rated load: 5500 kg (5.5 tonnes) Load center: 600 mm Turning radius: approx. 2375 mm - 2534 mm Lift height: up to 5300 mm Free lift: available Transmission: DuraMatch™ 1-speed or DuraMatch™ 2-speed Travel speed (loaded/unloaded): approx. 16.7 - 17.2 km/h Dimensions: approx. 3,500 mm * 1,420 mm * 2,500 mm mm Weight: approx. 7,800 kg Csdpewalyijfx Afworc Transport and loading can be arranged throughout Europe upon request for an additional charge. Prices exclude VAT. Viewings are available by appointment. Contact us; our team will be happy to assist you. Trade-ins or exchanges are possible! Machine Purchase/Sale PURCHASE/SALE OF PRODUCTION & METALWORKING MACHINES AND MUCH MORE. Do you need a high-quality, yet affordable metalworking machine for your production? Or do you want to sell yours? For further information or to contact us, visit our website

Condition: used, Year of construction: 2004, Hydr. reversing Bale size 0.8 - 180 m / Cedpfx Aferxta Ejwerc

Condition: new, maximum load weight: 50,400 kg, overall weight: 65,000 kg, axle configuration: > 3 axles, total width: 2,540 mm, Equipment: ABS, You can find our complete vehicle inventory, including units available immediately and at short notice, on our website. Excerpt from the equipment list. Full equipment specifications available on request. GOOSENECK * Gooseneck in SNT design to optimize loading platform length, approx. 3,700 mm long, with rear bevel approx. 1,000 mm x 10° * For tractor units: 4 x 2, 6 x 2, and 6 x 4 * Removable steel front wall, approx. 400 mm high * ASPÖCK-UNIBOX on the front connector strip with sockets * 3 kW electro-hydraulic unit for controlling hydraulic operations, excluding hydraulic winches * 1 pair of removable aluminum side boards, approx. 400 mm high, anodized finish * 1 removable aluminum tailgate, approx. 400 mm high, anodized finish * Approx. 40 mm thick hardwood floor above gooseneck, checker plate floor above king pin * 2-inch king pin * Rear section of gooseneck prepared for aluminum drive-on ramps * Round NATO socket on the front connection strip (Maeler & Kaege VG 96 917) LOADING PLATFORM * Extendable loading platform, approx. 8,800 mm long, with rear bevel approx. 500 mm x 10° * Recess in the loading platform and bevel for accommodating excavator dipper stick approx. 3,850 x 750 x 210/290 mm (L x W x H) * TPMS tire pressure monitoring system per ECE R 141 * BPW axles and suspension, 1st axle steerable, all remaining axles hydro-mechanically forced steered * 1st axle with electromagnetic reverse lockout, activated via reverse gear and manually * Technical axle load: 12,000 kg each, air suspension with raise and lower valve * Tires: 235/75 R 17.5, twin tires, 3PMSF * Mechanical landing legs with 2-speed gearbox and crank, JOST Module B – static test load approx. 50,000 kg * Continuous 50 mm thick hardwood floor on the loading platform and interrupted between axles (increases coefficient of friction) * 1 intermediate table, approx. 300 mm wide, for the extension tube with large cross-section * Extendable (galvanized) side extensions, approx. 230 mm per side (without wooden planks) * Wheel recesses with square climbing strips, approx. 15 x 15 mm ahead of axles, open through to gooseneck cross member, approx. 700 x 410 mm (W x D) * Aluminum covers for wheel recesses, usable as bridging elements for extension OR as widening planks * Aluminum elements lockable on telescopic tubes of the extensions * Widenable U-profiles for inserting ALU covers: - on the fixed section behind the gooseneck - on the intermediate table - on the extendable platform * Wheel recesses with square climbing strips, approx. 15 x 15 mm between 1st and 2nd axle, approx. 1,480 x 700 x 410 mm (L x W x D) * Aluminum covers for the wheel recesses, usable as bridging elements for the extension OR as widening planks * Aluminum elements lockable on the extension’s telescopic tubes * 1 pair of mechanical rear supports * Remote steering from front and rear via cable remote control, with axle tracking, without installation in the tractor unit HYDRAULIC LOADING RAMPS * One pair of two-section steel ramps, Type: DR-15/60-900-4350-KG-HV-M, approx. 4,350 mm in length and approx. 900 mm wide each * Hydraulically foldable ramp tips * Ramps can be shifted hydraulically approx. 235 mm outward and approx. 215 mm inward individually Crjdpfx Aotx Nwnsfwsc * Super Grip rubber surface approx. 25 mm and steel plate surface approx. 5 mm as additional

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 500 h, functionality: fully functional, machine/vehicle number: 25-029, total width: 800 mm, total length: 4,700 mm, total height: 1,900 mm, type of input current: three-phase, energy consumption: 2 kWh, Very good metal separator (inductive sorter) for separation of all kinds of metal (incl. stainless steel). Can be used before ECS, behind or stand alone. Ejecting of all metals larger 0.5 / 1 mm possible. Reasonable using for material up to 60 % metal content. Unique flap technology, no pressured air necessary. Machine is ready for using, can be visited or tested. If wished can be equipped with camera. If the machine is too small we can build also bigger. It is our demonstration machine. Throughput / capacity depending on material and purpose. Crodpfx Afsqabm Ejwec Price on negotiation!

Condition: used, functionality: fully functional, power: 186 kW (252.89 HP), fuel type: diesel, color: yellow, Year of construction: 2018, operating hours: 10,000 h, Equipment: air conditioning, Caterpillar 950M wheel loader Year of manufacture: 2018 10,000 hours 186 kW CAT C7.1 engine 20,000 kg 40 km/h Automatic air conditioning Camera Crodpfxsym Al Ue Afwec Onboard scale Hydraulic quick coupler 3rd hydraulic circuit Joystick control No steering wheel Newly serviced Full CAT service history Tyres like new Bucket available at extra cost

Condition: new, Year of construction: 2026, functionality: fully functional, power: 11 kW (14.96 HP), A triple pass rotary drum dryer is a type of industrial dryer that is used to reduce or remove moisture from a material. It gets its name from the three rotating drums through which the material passes, each with a different purpose in the drying process. This type of dryer is commonly used in the production of various bulk solids, including minerals, agricultural products, and biomass. Here are the key features and components of a triple pass rotary drum dryer: 1. Triple Pass Design: - The material being dried passes through three rotating drums or cylinders, hence the term "triple pass." Each drum serves a specific purpose in the drying process. 2. Material Flow: - The material enters the dryer and first passes through the innermost drum. After the initial drying phase, it moves to the middle drum and then to the outer drum, undergoing additional drying in each pass. 3. Heat Source: - Heat is typically provided by a combustion system, such as a burner or furnace, located at one end of the drum dryer. The hot gases generated by the combustion process flow through the rotating drums, transferring heat to the material. 4. Air Flow: - The dryer is designed to optimize air flow through the drums, ensuring efficient drying. In a triple pass design, the material and hot gases move counter-currently through the three drums, enhancing heat transfer and drying efficiency. 5. Lifting Flights or Lifters: - Lifters are internal components inside the drums designed to lift and cascade the material as it rotates. This movement promotes good heat transfer and uniform drying. 6. Retention Time: - The triple pass configuration allows for an extended retention time of the material in the drying system. This longer exposure to heat enhances the drying efficiency, making the triple pass rotary drum dryer suitable for materials with high moisture content. 7. Cooling Section: - After the material completes the three passes and reaches the end of the drum dryer, a cooling section may be included to reduce the temperature of the dried material before it is discharged. 8. Applications: - Triple pass rotary drum dryers are used in various industries, including agriculture (drying crops like grains), minerals (drying ores or concentrates), and biomass (drying wood chips or other organic materials). 9. Efficiency and Energy Consumption: - Triple pass rotary drum dryers are known for their high efficiency due to the extended drying time and effective heat transfer. However, they may have higher energy consumption compared to single or double pass dryers. When selecting a triple pass rotary drum dryer, it's essential to consider factors such as the type of material to be dried, required moisture reduction, and overall processing requirements. Proper design and operation are crucial to achieving optimal drying performance. Technical details We have different options for different requirements, please contact our team for more info. Crsdoq Nfuzopfx Afwec

Year of construction: 2002, condition: excellent (used), machine/vehicle number: Reg Nr. 976, Machine Name: Paddle dryer Used Manufacturer: AVA / Holland Merten GmbH Type: HTK 200 Construction year: 2002 Speed: 107 U/min Material: Stainless steel Driving force: 5,5 KW Model: EExdellCT4 Total content: 235 Liter Parts in contact with product: Stainless steel 1.4571 Gear box: Stirnradgetriebemotor Equipment: Double jacket, mechanical seal, shaft heater Dimensions: L 3400 x W 1100 x H 1500 mm Empty weight: approx. 1600 kg Message: Operating temperature 130°C Design temperature 200°C Internal pressure mixer -1/+3 bar Pressure double jacket +6 bar Accessories: Base frame, Maier head HWR 225 Condition: Used very good Cjdeitcvuopfx Afworc Price: on request

Condition: used, mileage: 53,857 km, power: 270 kW (367.10 HP), first registration: 06/2003, fuel type: diesel, overall weight: 36,000 kg, axle configuration: 3 axles, color: yellow, gearing type: automatic, emission class: euro3, total width: 2,680 mm, total height: 3,750 mm, Equipment: parking heater, Liebherr UTM 735 - Crane: LTM 1055/1 - Year of manufacture: 2003 - 22,439 operating hours (carrier chassis) Cedpfxow H Hwvj Afwerc - 18,883 operating hours (crane superstructure) - 53,857 km mileage - 4 x hydraulic boom extension - 16 m jib - Hydraulic steering - 12 t additional counterweights - LED beacon lights - Technical inspection due: - Safety inspection due: 01.2026 - Tyres: 445/95 R 25 Subject to errors and prior sale. Internal vehicle number: 11218 WhatsApp support available! For questions about the vehicle or for further information, feel free to contact us conveniently via WhatsApp.

Condition: excellent (used), functionality: fully functional, Year of construction: 2019, 1 Used Concrete Batching Plant In excellent condition! Manufacturer: EUROMECC Model: EURO 5 MIX Year of manufacture: 2019 Theoretical capacity: approx. 60–75 m³/h Total production to date: approx. 95,000 m³ Aggregate storage in high silo / inline silo (reihensilo) • Capacity: 5 bins – each 45 m³ • 4 load cells (each 5,000 kg capacity) • Silo loading via feed conveyor belt • Truck feed via loading hopper (25 m³ volume) Complete plant with winter enclosure / insulation Mixers • 1x Planetary mixers with agitators • Type EUROMECC MEP 3000/2000 Dosing system • Aggregates: Weighing belt • Water dosing: 1 water scale 500 kg per scale • Admixture dosing: 1 admixture scale 2x12 liters • Cement dosing: 1 cement scale 1,000 kg per scale Control system • Operator/control container included • Main control system: ElettronData Cement silos – total: 6 units • 2x 150 m³ (Diameter: 4.6 m) • 1x 90 m³ (Diameter: 3.5 m) • 1x 45 m³ (Diameter: 3.5 m) Optional equipment: • Warm air heating system inside container • Chemical admixture storage in container • Rest concrete recycling system (optional) Condition: • The plant is in very good and fully functional condition. • AVAILABLE IMMEDIATELY • Location: Denmark • Price: on request Note: Offer is net ex-works, subject to prior sale. Errors, omissions, and/or misrepresentations excepted. No warranty or guarantee. Sold “as-is”, lying or standing. Any duplication, publication or reuse of this offer – in part or whole – is strictly prohibited. Crsdpfsxn A Nbjx Afwjc

Condition: ready for operation (used), Year of construction: 1989, An aluminum die casting system is available. Clamping force: 2200kN, opening force: 71kN, max. opening stroke: 430mm, mold closure: double toggle lever, pressure chamber: cold chamber, position: horizontal. Filling piston diameter min./max.: 40mm/70mm, pressure chamber filling volume min./max.: 293cm³/898cm³, casting pressure: 1990bar, blast area min./max.: 110cm²/338cm², output: 780 cycles/h. Clamping plate dimensions X/Y: 755mm/755mm, column spacing: 500mm/500mm, mold height min./max.: 250mm/600mm, min. mold dimensions X/Y: 296mm/296mm. Including crucible furnace, blow-out device, automatic dosing unit and 4x control cabinets. Documentation available. Crsdpfxjucfwps Afwsc