Centering point face driver

Neidlein** OEX 5 MK5 Ø 39 mm

Condition: new, functionality: fully functional, turning diameter over cross slide: 330 mm, spindle bore: 78 mm, turning diameter over bed slide: 520 mm, center height: 260 mm, turning length: 1,000 mm, quill stroke: 127 mm, quill diameter: 68 mm, total length: 2,160 mm, total width: 810 mm, spindle speed (max.): 2,000 rpm, spindle speed (min.): 20 rpm, bed width: 300 mm, overall weight: 1,810 kg, quill mount: MK 4, Equipment: rotational speed infinitely variable, Tip height: 260 mm Center distance: 1000 mm Spindle bore: 78 mm Spindle nose according to DIN 55029 Camlock D8 Giodoh Rvxhepfx Afnjn Spindle speed range: 20-2000 rpm Drive power: 7.5 kW Features include infinitely variable speed control Hardened and precision-ground Z-axis guideways Turcite coatings (on mating surface) of the tool and cross slides Manual central lubrication with one pump for longitudinal and cross slides Complete coolant system with rear splash guard and splash guard on the slide Chuck guard Switch rod with 3 adjustable cams Machine light Fixed center point Set of machine mounting plates

Condition: excellent (used), Year of construction: 2009, - Digital display. - Accessories available. Tips Height 170 mm Tip width 650 mm turning diameter over the bed 350 mm over the cross slide 196 mm in the offset 535 mm Width in front of the front plate 165 mm Spindle Spindle bore 42 mm Spindle nose D1-4" Camlock Morse taper in bushing no. 3 MT Spindle speeds 3 speed ranges 0 - 3250 rpm Main motor 7.5 kW (10 HP) Bed Slide guide width 318 mm Guide type V-shaped and flat Cross slide Width and length 180 - 850 mm Travel 250 mm Top slide Width 90 mm Travel 130 mm Tool holder 20 x 20 mm Quick-action tool lock Dickson No. 2 Tailstock Diameter of quill (nominal value) 63 mm Travel 145 mm Morse taper no. 4 M.T. Offset ±12 mm Giedjtr Ud Sepfx Afnjn Lead screw Diameter 32 mm Thread 6 mm pitch or 4 T.P.I. Thread Metric Pitch 0.2 - 14 mm (51) Inch thread T.P.I. 2 -56 (56) Module thread pitches 0.2 - 3.5 (20) Diametrical pitch (D.P.) 8 - 56 (20) Feed rate Metric (R10 series) 0.018 - 1.2 mm/rev Inch (R10 series) 0.0007 - 0.048"/rev Face feed = approx. half of the longitudinal values Machine height Floor to spindle center 1070 mm Total length 1250 mm Machine 2500 mm Total width 1100 mm Height over all 1300 mm Cooling pump Type AQ 3MG Headstock oil pump Type Interlube three-phase 27662-131 Weight 1250 mm between tips approx. 1450 kg

Condition: used, Year of construction: 2003, machine/vehicle number: 1527, Used lead and feed screw lathe COLCHESTER Triumph VS 2500 Centre height: 195mm Distance between centers: 650mm Spindle bore: 54mm Infinitely variable speed: 14–2500 rpm Tailstock quill: MT5, coolant system, quick thread cutting device Digital readout: FAGOR NUP 300 TS-RS 1 x RÖHM 3-jaw chuck, 5-position stop drum, spindle stop, machine lamp, 1 x PARAT 4-way turret, 4 x PARAT tool holders, live centre and quick-action drill chuck. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Inspection of the machine is possible by appointment. Gjdpfxex Hrums Afnein

Condition: ready for operation (used), Year of construction: 2015, operating hours: 5,000 h, spindle speed (max.): 2,500 rpm, overall weight: 1,800 kg, This Colchester Triumph VS 2500 was manufactured in 2015. It features a conventional pull and lead screw, infinitely variable speed adjustment, and a digital display. Key specifications include a turning diameter of 400mm, center height of 195mm, and a bed width of 1270mm. It also comes equipped with a MultiFix quick-change tool holder, maximum spindle speed of 2500rpm, and a motor power of 7.5kW. Weight is 1,800kg. Contact us for more information about this machine. • Control: Conventional with lead screw and infinitely variable speed adjustment • Readouts: Digital display for axes and digital spindle speed display • Operating hours: No counter; estimated 5,000–7,000 h • Turning diameter: 400 mm • Center height: 195 mm • Bed width: 1270 mm • Toolpost: MultiFix quick-change tool holder Additional equipment Godpfxox D Nwde Afnoin • 3x three-jaw chucks • 3 sets of claw jaws • Chuck wrench • Manual/operating instructions • Work area lamp • Digital dial indicator • 4 MultiFix tool holders • Various turning tools • Drill chuck (keyless) for tailstock • Coolant pump

Condition: used, Year of construction: 1991, functionality: fully functional, machine/vehicle number: 91-160-2498, Used WEILER PRAKTIKANT 160 lead and feed screw lathe Centre height: 160 mm Centre distance: 650 mm Giedpfxjyciw Ao Afnen Spindle speeds approx. 48–2,500 rpm Spindle bore: 40.5 mm Leadscrew and feed shaft are covered. Scope of delivery: Including 3-axis digital readout from Heidenhain, chip guard back wall, lever collet system (without collets), 1 x faceplate Ø 250 mm, electrically interlocked chuck guard, machine lamp, Multifix size A quick-change toolpost with 4 holders, bed stop, cooling unit, and fixed steady rest. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Viewing by appointment is possible.

Condition: good (used), functionality: fully functional, turning diameter: 400 mm, turning diameter over top slide: 240 mm, center height: 200 mm, turning length: 1,100 mm, total length: 2,500 mm, total width: 1,100 mm, total height: 1,900 mm, spindle speed (max.): 2,500 rpm, overall weight: 1,500 kg, three-jaw chuck diameter: 240 mm, TECHNICAL SPECIFICATIONS & EQUIPMENT: Operating voltage: 380 V Frequency: 50 Hz Rated current: 21 A Spindle speed: 75–2500 rpm Spindle bore: approx. 52 mm Giedpfx Aew U Tn Nefnen Centre distance: 1100 mm Centre height over bed: approx. 200 mm Swing over bed: 400 mm Centre height over cross slide: 120 mm Swing over cross slide: approx. 240 mm The machine is equipped with a tailstock, a Multifix tool holder, and a 3-jaw chuck Diameter: 240 mm Including two-axis digital readout by manufacturer FAGOR REFERENCE NUMBER: 14 DIMENSIONS & WEIGHT: 2500 x 1100 x 1900 mm 1500 kg PICK-UP INFORMATION: The item will be available from September 2025. A collection date must still be arranged on a specific day from 01.09.2025 onwards FCA: 73235 Weilheim an der Teck (DE), loaded onto truck

Condition: excellent (used), functionality: fully functional, Emcomat 17D Lead and Feed Screw Lathe with 3-Axis Digital Readout K&C New from Training Workshop Excellent Condition!!! Technical Data: >> Year of manufacture: approx. 2000 >> Machine no.: D3F H1 010 >> Centre height: 170 mm >> Swing over bed: 340 mm >> Swing over cross slide: 190 mm >> Turning length: 700 mm >> Spindle speed: 4 speed ranges, stepless from 35 to 3000 rpm >> Tailstock quill stroke: 120 mm >> Tailstock: MT3 >> Spindle bore: 50 mm Giedpfx Aowvuf Tsfnsn >> 20 longitudinal feeds: 0.045 – 0.787 mm/rev >> 20 cross feeds: 0.023 – 0.406 mm/rev >> Required floor space approx. (L x D x H): 1.600 x 0.9 x 1.3 meters >> Weight: approx. 730 kg Equipment and Accessories: >> 3-axis digital readout from K&C, new, with 12 months manufacturer’s warranty and operating manual Functions: mm/inch switching, coordinate selection ABS/INC, value halving, reference point, tool programming for 200 tools, taper calculation, radius/diameter display, quick zeroing, count direction switching >> 1 piece three-jaw chuck NEW 160 mm, 2 sets of jaws >> Multifix B toolholder with 2 tool pockets >> Chip guard >> Coolant system About the machine: Offered here is an Emcomat 17D lead and feed screw lathe, approx. year 2000, in very good condition. The machine is of course fully functional. The bedways are in excellent condition. The Emco is equipped with a new 3-axis digital readout from K&C and a new three-jaw chuck. Take the opportunity to inspect the machine under power on site and see the condition for yourself.

Condition: excellent (used), functionality: fully functional, Distance between centers: 1500 mm Center height: 220 mm Spindle bore: 52 mm Gisdpfx Afsx S Hynsnon Tailstock quill: MK 4 18 speeds: 25 - 2000 rpm Pole-change motor: 2.9 / 5.9 kW with gap bed bridge

Condition: ready for operation (used), Colchester Triumph 2500 Lathe Gijdsxfrgdepfx Afnen Swing over bed: 400 mm Swing over cross slide: 246 mm Distance between centres: 1270 mm Centre height: 195 mm Max. turning diameter: 585 mm Spindle motor power: max. 7.5 kW Spindle speed: max. 2,500 rpm Infinitely variable spindle speed ranges: - low: 14–300 rpm - medium: 36–830 rpm - high: 109–2,500 rpm Overall dimensions: 2,600 mm x 1,300 mm x 1,800 mm (L x W x H) Accessories: 5 Multifix tool holders Steady rest Live and dead centers Drill chuck Jaws Cabinet Coolant pump You are welcome to come and inspect the machine. We are happy to organize affordable shipping for you. You will receive a proper invoice. A net invoice can be issued for international customers with a valid VAT ID number. Subject to prior sale. Visit our shop and see our other offers. The company names and trademarks mentioned are the property of their respective owners and are used for identification and description purposes only. Technical data may be subject to deviations, and errors in the item description may occur and are reserved.

Condition: used, Year of construction: 1985, Weiler Praktikant 140 lathe, built in 1985, with three-jaw chuck and Multifix. The Z-axis guide is slightly worn in the front area. The machine is in good working order. Can be demonstrated live by arrangement. Giedsv N Awfspfx Afnjn