Honing Machine - Internal - Vertical

NAGEL 3VS8-50T

Condition: excellent (used), Sunnen GH210 Horizontal Hone Year 2010 Max Stroke 8000mm, Spindle Speed:0 - 300 rpm Maximum Spindle Power: 40 Hp (29.83 kW) Maximum Stroker Power: 18 Hp (13.42 kW) Stroke Speed Range: 0 – 100 ft/min (0 – 30.5 m/min) I.D. Range: 2 – 24 inches (50.8 – 609.6 mm) O.D. Range: 26 inches standard (660.4 mm) Maximum Part Weight: 8000 kg Approximate Machine Weight: 12,066 kg Gsdpfx Aow U Uh Dsi Nouc 400 VAC 50 Hz, 3-Phase (85 A) Siemens Simatic Control,

Condition: refurbished (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: 30214501, turning length: 2,000 mm, total length: 12,000 mm, WFL Millturn M60/2000 WORKING RANGE center distance mm 2000 swing over bed, turning diameter mm 690 MAIN DRIVE AC-drive with 2 gear steps drive power 100% duty cycle kW 40 max. speed min-1 3300 max. torque at the spindle 100% duty cycle Nm 1830 TAILSTOCK quill diameter mm 140 quill travel mm 160 quill force (adjustable) N 3500-31000 quill with installed live center MK 5 TOOL HOLDER (single tool holder, turning-boring-milling unit) AC-drive drive power 100% duty cycle kW 30 speed range max. min-1 6000 max. torque at the spindle 100% duty cycle Nm 315 travel vertical to the X/Z-plane (Y-axis) mm 300[-125/+175] pivot capability of the milling spindle (B-axis) ° -110/+90 spindle head acc. DIN 69893 HSK-A100 Gedpfx Aisu Hl R Ts Njuc spindle diameter in front bearing mm 100 DIMENSIONS length (max. tool magazine) m 11 width/height m 3,9/3,3

Condition: used, Year of construction: 2007, table diameter 4520 mm table load 35000 kg swivelling range 110 Grad total power requirement 44 kW weight of the machine ca. / t required space / m Type: ROMAT 350 / LVEB-120000N-4m / VVEs-D-18000N-5m-S / QVEB-2m travelling beam / CR-200000N / Hydraulic scissor lift table In the scope of delivery: Item Designation 1 Welding power source GLC 603 Quinto SD 2 Wire drum 3 Service door 2.1 4 Robot control cabinet 5 Service door 1.2 6 Scissor lift table (shown in parking position) 7 Cross-travelling unit QVEB 8 ROMAT 350 robot 9 Service door 1.1 10 Safety fence 11 Platform 12 Positioner 13 Sliding door 1 14 Linear traversing unit LVEB 15 Vertical traversing unit VVEs 16 Sliding door 2 The disc ring on the table is a device that is not included in the scope of delivery ----- Technical data - Mechanical dimensions (without control unit and superstructures): approx.6440(57 7 0)x4520(2700)x5460(3320) LxWxH - Turntable diameter: 4520mm - Weight: approx. 25,000kg (without superstructure) - Speed range: 0.004 - 1.07 rpm - Welding current coupling: 600 A - Maximum table load capacity: 35 tons (according to load chart) Ambient temperature Storage / transport 0 to 60'C Operation +4 to 35 "C Interfaces Central transfer point for control, power supply, earth connection ----- 2.3 Linear traversing unit, LVEB Type LVEB-120000N 4m Dimensions W x D x H 7,700 x 2,440 x 776 mm Weight 4,355 kg Travelling distance 4,000 mm Load of the carriage 120,000 N Drive unit Gear motor Precision bevel gear motor Manufacturer Stöber Type K402VF0250EK703V Power 4.21 kW Voltage UKE 140 V / 1000 rpm Current Rated current IN: 8.32 A Type of current Standstill current I0: 9.04 A Motor speed 3,000 rpm Gear ratio i = 25.28 ----- 2.4 Vertical traversing unit, VVEs Type VVEs-5m Dimensions W x D x H 2,000 x 1,960 x 7,150 mm Weight 9,500 kg Travelling distance 5,000 mm Max. moving mass 18,000 N Drive unit Gear motor Bevel gear motor with brake Manufacturer Stöber Type K713VF0790MQ30ED704B Power 4.8 kW Motor speed 2,000 rpm Gear ratio i = 78.83 (20181/256) Gusdsrmulvjpfx Ai Noc ----- 2.5 Cross-travelling unit, QVEB Type QVEB-2m Dimensions W x D x H 1,270 x 4,100 x 756 mm Weight 1,950 kg Travelling distance 2,000 mm Load on the travelling beam 10,000 N Max. moving mass 18,000 N Drive unit Gear motor Precision flat geared motor Manufacturer Stöber Type FS202VQ0145ED402U Power 1.43 kW Voltage UKE 140 V / 1000 rpm Rated current IN 2.86 A Type of current Standstill current I0: 3.1 A Motor speed 3,000 rpm Gear ratio i = 14.65 (3180/217) ----- 2.6 Rotary indexing table Type CR-200kN Manufacturer Cloos Dimensions W x D x H 1,820 x 2,120 x 541 mm Weight 2,850 kg Drive unit Gear motor Bevel gear motor Manufacturer Stöber Type K814VG1540EK803U Power 6.7 kW Motor speed 3,000 rpm Gear ratio i = 154.322 ----- 2.7 Robot ROMAT 350 Type ROMAT 350 Dimensions (W x D x H) in reference position 1,900 x 600 x 1,500 mm Weight 205 kg Footprint 500 x 515 mm N...

Condition: good (used), workpiece diameter between centers: 2,286 mm, The No. 61 Angular Hypoid Tester is designed to test large bevel and hypoid gears up to 90" diameter and with shaft angles from 0 - 135 degrees. Spur, helical and internal gears can also be accommodated. The drive or pinion spindle can be rotated in either direction at a recommended spindle speed of 600 RPM. It is mounted in a head which is vertically adjustable on a column, so that the spindle can be offset either above or below the center line of the gear spindle for testing hypoid gears. The pinion head column is adjustable angularly in a horizontal plane to permit testing of gears of any shaft angle from 0 - 135 degrees. Specifications: Centerline of Drive Spindle to Nose of Brake Spindle (90 degrees shaft angle and without face plate): 38-1/2" Max. / 7-5/8" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and without face plate): 60" Max. / 10" Min. Centerline of Brake Spindle to Nose of Drive Spindle (90 degrees shaft angle and with 54" face plate): 60" Max. / 28" Min. Gjdpfxsrtrzde Ai Neuc Centerline of Brake Spindle to Centerline of Drive Spindle (For Spur Gears): 56" Max. / 6" Min. Distance Between Nose of Brake Spindle and Nose of Drive Spindle (for spur gears): 36-1/2" Max. / 0" Min. Offset of Drive Spindle Either Above or Below Centerline of Brake Spindle: 10" Range of Shaft Angles: 0 - 360 Degrees Maximum Diameter of Gear: 90" Diameter of Face Plate: 54" Outboard Bearing: 3" Diameter Hole Spindles: RPM of Drive Spindle Pulley Set No. 1: 100 - 400 RPM of Drive Spindle Pulley Set No. 2: 250 - 600 Diameter of Taper Hole (large end): 6" Taper Per Foot: 3/4" Depth of Taper: 8" Hole Through Spindle: 5-1/2" Net Weight of Machine: 20,000# Net Weight of Machine W/Outboard Support and Bed Plate: 24,000#

Condition: used, Year of construction: 1994, sheet width / mm plate thickness / mm distance between columns / mm Manufacturer: EHT Type: TSS 20-25 Year of construction: 1994 Max. Cutting length: 2250 mm Max. Sheet thickness: 20 mm Strip width min / max: 10/1000 mm Distance between the consoles: 2530 Height above the ground: 900 mm Table length without extension arms: 3030 mm Oil volume: 800 l Max. Pressure: 280 bar Operating voltage: 400V Control voltage: 230 V. Nominal current: 87 A. Gjdjuddh Aepfx Ai Neuc Weight: 15.8 to Dimensions L x W x H: 3500 x 2500 x 2400 mm Accessories / special equipment Pneumatic cutting gap adjustment Cutting length limitation Roller conveyor elevation bracket Hand protection 1 bay Multitron control Multitron PS 80; ELCO 85 P Lower knife height adjustment

Condition: used, Year of construction: 1978, machine/vehicle number: NBGMAN 2, Technical data: 1 Abus VS column slewing crane NL 1000 KG Payload at full radius 1000 KG / 1 ton payload Height: approx. 3.65m, UK boom: approx. 3.27m Projection: approx. 5m, hook height: approx. 2.75m Weight completely approx. 1000 kg including 1000KG Abus GM chain hoist (BJ2008) with floor control (2 lifting speeds) Connection to 400V 16A, swivel range 360° Gusdpfx Aor Igtkji Noc Test book is available Crane is dismantled and available immediately Item location is 75053 Gondelsheim Only the crane system shown in the pictures is sold Very good condition, see pictures Shipping by courier or collection by appointment

Condition: good (used), Year of construction: 2000, operating hours: 1,500 h, Cloos Romat 310 overhauled in good condition and still in operation for a short time. Gedpfx Aistctnke Nouc

Condition: used, GEHRING Lifehone 600 is a CNC vertical honing machine, engineered for precision, high accuracy and reliability. Capacities: min diameter 3 mm, max 90 mm, max honing length 600 mm; total stroke 600 mm. Technical specs: spindle speeds up to 4500 t/min; stroke/feed speed up to 60 m/min; voltage 3x 400 V 50 Hz; machine weight about 2500 kg; overall dimensions L2600×W2800×H3100 mm. Equipment: coolant system and paper filtration system. Achieves tight tolerances; typical applications include automotive, aerospace, machine tools, medical and watchmaking. Guodpfx Aioyxnyco Nsc

Condition: good (used), Airless sprayer, painting device, spray pack, paint sprayer, paint spray system, paint pump, electrostatic sprayer, airless complete system, pneumatic piston pumps, airless high-pressure pump, air motor, AIR MOTOR -Manufacturer: Wagner, Airless sprayer type: 33-70 with transport trolley and spray gun -Material flow: max. 12.6 l/min -Air inlet pressure: max. 8 bar, operating pressure max. 264 bar -Individual components: see photos Gedpew U T Atsfx Ai Nsuc -Dimensions: 830/680/H1140 mm -Weight: 50 kg

Condition: excellent (used), Year of construction: 2015, operating hours: 23,488 h, functionality: fully functional, travel distance X-axis: 20,000 mm, travel distance Y-axis: 3,500 mm, travel distance Z-axis: 1,250 mm, UNISIGN UNIPORT 7000 CNC Portal Milling and Drilling Machine For sale is a heavy-duty CNC portal milling/drilling machine, type UNISIGN UNIPORT 7000, from an Italian group that is relocating product-specific machining operations abroad. Due to compliance and safety regulations, as well as the associated workpiece protection measures, the complete photographic documentation of the machine will only be provided upon request to select, end-user customers. The machine features a very large working area with 20,000 mm of travel in the X-axis, 3,500 mm of travel in the Y-axis, and a robust portal design suitable for large and heavy workpieces. Technical specifications: Manufacturer: UNISIGN Type: UNIPORT 7000 Machine type: CNC Portal Milling/Drilling Machine Control system: Siemens Sinumerik 840-D Travel distances: X-axis: 20,000 mm Y-axis: 3,500 mm Z-axis: 1,250 mm Table: approx. 22,250 x 3,170 mm Max. table load: 2,000 kg/m² Portal clearance width: 3,000 mm Distance from spindle nose to table: 250 – 1,500 mm Spindle: Tool interface: HSK 100 Spindle power: 36 kW Max. spindle speed: 4,000 rpm Max. torque: 1,350 Nm Gearbox: 2-stage Machining performance in C45 steel: Full drilling: Ø 130 mm Thread drilling: M55 Milling performance: approx. 1,200 cm³/min Tool magazine: Chain magazine with 48 positions Max. tool length: 500 mm Max. tool weight: 25 kg Tool change time: approx. 10 seconds Feed rate / Rapid traverse: Rapid traverse X/Y/Z: 40,000 mm/min Feed rate range: 5 – 40,000 mm/min Machine data: Machine weight: approx. 146,000 kg Footprint: approx. 28,500 x 10,800 mm Overall height: approx. 5,000 mm Connected load: approx. 80 kVA Electrical system: 400 V / 50 Hz / 3 phases Description: Guedpfx Ajzcqw Rsi Nsc Heavy-duty CNC portal milling machine with a stable portal design, suitable for machining large and heavy workpieces. The machine is equipped with a Siemens Sinumerik 840-D control system, a powerful main spindle, a large table, and an automatic tool magazine. Ideal for mechanical engineering, large part machining, mold making, steel construction, energy technology, or similar applications. Technical specifications are based on available documentation. Subject to change and errors. Inspection possible by appointment.