Used Sand for sale (2,178)

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance Dwedpfxet Tqy Ej Agfeb thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Year of construction: 2010, condition: used, functionality: fully functional, machine/vehicle number: 01810, 7 Face grinding supports 2 Top chamfering tools 2 Bottom chamfering tools 1 Water groove milling support 1 Milling support Dwodpszy Eh Refx Agfeb Infeed and outfeed roller conveyor Belt running direction: left to right Water trough

Year of construction: 1995, condition: not inspected (used), Number of sanding units 2 st. sanding width 180 mm Sanding height max. 150 mm MAWEG Robert Hildebrand Saturn Duo Professional two-belt finish sanding machine with brushing unit Double-sided; sands from top and bottom Pneumatic belt oscillation Pneumatic belt tensioning Feed via top and bottom conveyor belts with spring-loaded hold-down rollers; infinitely variable speed (5–15 m/min) Workpiece thickness adjustment with pre-selectable stock removal amount at machine infeed, based on sensing the raw timber thickness Adjustment to wood thickness via motorized positioning of the machine's upper section Digital thickness setting via mechanical counter with 0.1 mm display and zero-point adjustment Safety switch for oversized wood thickness at machine infeed Double-sided brushing unit with integrated workpiece blow-off Sanding belt blow-off (top and bottom) Belt breakage monitoring switch with automatic shutdown of all drives Technical data: Top motor: 4 kW Bottom motor: 4 kW Top brush: 0.37 kW Bottom brush: 0.37 kW Feed drive: 0.5 kW Height adjustment: 0.12 kW Compressed air requirement: 6 bar, 400 NL/min Sanding belt speed: 25 m/sec Machine dimensions: 1,600 mm length 1,150 mm width 1,800 mm height Workpiece dimensions: Min. thickness 15 mm, max. thickness 150 mm Min. width 10 mm, max. width 180 mm Dwodpfxozqgg Ae Agfsb Min. length 290 mm 4 extraction ports: 2 x 120 mm, 2 x 80 mm; required air velocity at extraction port: 25 m/sec (Technical specifications according to manufacturer – subject to change/no guarantee!)

Condition: used, Year of construction: 2022, Plus freight 4,000.00 € and installation and commissioning 5,000.00 € Grinding system B Sand 5 with partial lathe Working principle The panel is placed on the infeed table. It goes into the partial lathe and centered. It is ground in the grinding system, through and back. The panel is turned in the partial lathe. It is ground on the other side in the grinding system. Then there are two options: either the panel goes onto the outfeed table and unloaded or it comes back onto the infeed table and is unloaded there (the second option extends the working time). Grinding system equipment 1 upper grinding lamella roller suitable for surfaces. Power 3 kW; D 420 mm; L 1300 mm. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. Cross brush suitable for grinding the cross fibers. D 420 mm; L 300 mm. Power 1.1 kW. 3 upper sanding discs for perfectly trimming the longitudinal and transverse wood fibers. Power 1.5 kW each; D 400 mm. Disc brush for beveling edges. The unit functions as a deep brush. After detecting the panel edges, it will follow the door edges. Power 0.75 kW; D 250 mm. Machine features: -The unique sanding system of this machine guarantees perfect wood sanding and/or intermediate sanding of the panels. -All tools are controlled by frequency converters. -All brushes are equipped with quick-release sanding strips without replacing the hub. -The discs are equipped with air bladders to optimize cleaning and service life. -Sanding discs are equipped with a Velcro fastening system. -The feed and rotation speed are PLC-controlled to prevent edge breakage. -High-quality sanding on 4 sides thanks to the system's constant removal rate. -Automatic and rapid unit changeover. - Constant throughput height, PLC and industrial software enable interlinking in a surface line. - Continuously variable speed of the discs, brushes and feed thanks to the fully equipped frequency converter. - Right/left rotation of the discs and brushes with different abrasive grits. - Individually driven feed of the discs, rollers and belts. - Additional adjustment of the brushes and discs to balance the use of the abrasive and to allow for changing the grinding pressure on the surfaces. - Strong support bed made of tubular steel guarantees the best rigidity, stability and flatness. - Planed upper support bed to ensure the best parallelism of the working surface for the grinding discs. - All unit carriages are designed with linear recirculating ball bearing guides, thus high load capacity and high precision. - Motorized feed belt controlled by a frequency converter, 0.55 kW. Machine doors equipped with safety devices. - Machine doors equipped with windows to observe the workpieces during operation. - Under the units, there are 80 mm rubber-coated pressure rollers to hold the workpieces in place during processing. · Low follow-up costs thanks to individual blade replacement. · Low running noise thanks to the enclosed system housing. · All units have suction housings with their respective suction supports. Cover plate with suction nozzle. · Completely encapsulated machine housing for a clean environment. Djdpfx Aevvkipsgfswb

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, Type: K77 - Year of manufacture: 1995 - Table size: 970 × 180 mm - Operating voltage: 400 V - Power voltage: 230 V - Power: 2.4 kW - Frequency: 50 Hz - Includes: sanding belts: 120 grit, 12 pieces; 80 grit, 4 pieces; 150 grit, 10 pieces Transport possible for an additional charge! The machine will be inspected before sale. For used machines manufactured in 2009 or earlier, the warranty is excluded when sold to commercial customers. Technical data and equipment may vary. Errors, prior sales, and changes are subject to change. All information without guarantee. Dwedoy Sap Aspfx Agfeb

Condition: good (used), Code: 0449 Brand: DE STEFANI Model: MV 1 Automatic single-head edge sander for wooden edges and profiles, solid wood, veneered and various Sander for profiles and rebates with interchangeable pad, tiltable -15° to +90° 2-speed motor rpm 710/1420 – Hp 1,3 – 2,5 Working height mm 100 Automatic feed with variable speed Adjustable inlet guide Compressed air 6 atm Dwjdpfxjzmyp As Agfob Exhaust outlet diameter 100 mm Overall dimensions mm 2100 x 1600 x 1350 h Weight kg 950

Condition: good (used), Code: 0749 Brand: TAGLIABUE - COSTA LEVIGATRICI Model: TT 3 1300 Dedpfx Agoh T Dzqjfswb Automatic sanding machine for worktops, furniture, panels, tables Technical data: Working width mm 1300 Max working thickness mm 130 Min working thickness mm 1 Composition: 1° Transversal belt - Motor Hp 15 - Electronic speed variator with display 2° Transversal belt - Motor Hp 15 - Electronic speed variator with display Transversal sanding belt size mm 1350 x 150 Chevron belt size mm 5510 x 140 Belt blowers Belt feed speed mt/min 5/25 Fixed table and mobile head for on-line set-up Panel cleaning rotary blowers Vacuum table Belt cleaning brush Infeed roller conveyor Installed power Kw 32 Compressed air 7 Atm Suction inlets: n° 2 diameter mm 200 - n° 2 diameter mm 150 - n° 2 diameter mm 100 Overall dimensions mmm 4400 x 2500 x 1600 h Weight kg 5000

Year of construction: 1994, condition: used, Second-hand machine Year of manufacture: 1994 Features and technical specifications: Working width: 300 mm Sanding belt oscillation: mechanical Roller guide: rubber-coated Grinding unit: with grinding shoe Feed speed: 2-speed Feed direction: reversible (forward/reverse) Motor start-up: star-delta Mains connection: 380 V Weight: approx. 450 kg Dsdpfxszk Nucs Agfewb Availability: at short notice Location: Baden-Württemberg

Condition: used, Year of construction: 1996, Technical data: - Manufacturer: Venjakob - Type: VBS 1300 - Working width: 1.300mm - Year of construction: 1996 Dedpfx Ajyyyhujgfewb - Operating side: left - Electric height adjustment of the sanding rollers - Constant table height, working height 920+-20mm - Manufacturer of brush sanding heads: Flex Trimm - Number of brush sanding heads: 2 pieces - Diameter of the sanding heads: 280/390mm - Sanding centre length 55mm - Roller1, grit 240, roller2, grit 280 - Speed of the brush sanding heads: 100-1000 rpm - Angled brushes - With brush oscillation - With vacuum belt - Feed speed: 1.5 - 7.5m/min. - Motor power 4KW - Machinelength: 3.500mm - Very sturdily built machine - Colour: light grey RAL 7035 - Total connected load 16KW - weight: 2740 kg

Condition: used, Year of construction: 1991, - Manufacturer: Fladder - Model: Gyro 300 Vacuum - Working width: 1300 mm - Year of manufacture: 1991, good condition - Flex Trim sanding heads - Quick-change sanding media - Sanding media grit: K240 - Sanding media length: 45 mm with support brushes - Abrasive slits: 20 and 5 mm - Number of brush heads: 6 Dwodpfx Aszia Nnsgfjb - Rotating and oscillating sanding unit - Motor power: 5 kW - New frequency inverter for the conveyor belt - With vacuum conveyor belt - Feed rate: continuously adjustable from 2 to 8 m/min - Length: 2070 mm - Width: 2370 mm - Height: 2240 mm - Weight: 2300 kg - Location: In stock, D 32825 Blomberg - Volts, Hz: 400 / 50 - Can be tested in Blomberg

Condition: used, Year of construction: 2014, Equipment: - Brush grinding machine with rotating grinding brush belt - Motorized height adjustment of the grinding unit, adjustment range from approx. 0 - 80 mm, freely programmable via machine control. - Operating side in the direction of travel, right - Rotating brush set consisting of 174 segment brushes, length 1,300 mm. Segments are easy to change and are inserted into the brush belt from the side. - With vacuum conveyor belt - With cleaning roller for the feed belt Dwjdpjxrb Rfsfx Agfob Technical data: - Working width: 1300 mm - Max. part thickness approx. 80 mm (depending on the abrasive coating) - Working height: 850 - 900 mm - Year of manufacture 2014 - Feed continuously adjustable, 3 m/min-10 m/min - Machine length: 3860 mm - Machine width: 2400 mm - Machine height: 2000 mm - Paint finish in RAL 7035, light gray with - Contrast color green - Voltage: 400V/50HZ - Electrical connection 16kW/36A - Machine weight: approx. 2600 kg

Condition: used, Year of construction: 1998, Technical Data: - Manufacturer: Ernst - Type: BM 2 - 1300 - Year of Manufacture: 1998 - Max. brush width: 1,300 mm - Max. brush diameter: 400 mm - Max. working height: 100 mm Dwodpfxozubpas Agfsb - Brush motors: 2 × 5.5 kW - Vacuum motor – rated power 7.5 kW - Vacuum motor – speed 2,800 rpm - Height adjustment motor – rated power: 0.45 kW - Height adjustment motor – speed 1,410 rpm - Brush speed 30-350 rpm - Feed rate 3-15 m/min. - Weight: 1900 kg 2.5 ELECTRICAL CONNECTION - Operating voltage 400 V - Frequency 50 Hz - Fuse to be provided by the customer: 63 A - Full load current: 47 A - The cross-section of the supply cable must be at least AWG 2 (25 mm2). 2.6 PNEUMATIC CONNECTION - Operating pressure 6–8 bar - Maximum pressure 8 bar 2.7 EXHAUST CONNECTION - Connection size 4 x Ø = 140 mm - Air requirement 1,108 m3/h per connection - Minimum air velocity at the connection on the machine 20 m/s - Vacuum at the exhaust connection 1,180 Pa For blowing device: - Connection size 3 × Ø = 80 mm - Air requirement 390 m3/h per connection - Minimum air velocity at the connection on the machine 20 m/s - Vacuum at the exhaust connection 950 Pa - Vacuum outlet 1 × Ø = 200 mm, 300 m3/h

Condition: used, Year of construction: 2001, - Manufacturer: Unisanding - Type: 2.2.0. 0-30 - Working width: 1300mm - Year of manufacture 2000 - 2 rollers flexibly adjustable from 0-30 ° working from above - Flex-Trim special brushes - Vacuum belt with vacuum motor - With glass pane on the operating side - External control panel with LCD control - Grinding motors: 2 x 2.2 kW with thermal contact - Feed motor: 1 x 1.5 kW with thermal contact - Vacuum motor: 1 x 5.5 kW - Height axis rollers: 1 x 0.18 kW - Feed 2-10 m/min frequency controlled - Brush speed: 50 - 350 rpm, frequency controlled - Voltage: 3 x 400V, 50Hz - El. Power 15KW - Fuse: 63A - Exhaust air volume (vacuum) 3,000 m³/h Dedpfxoxtakms Agfewb - Dust extraction volume: 2,000m³/h – 5,000m³/h depending on the customer - Length: 2,170 mm - Width: 2,040mm - Height: 2,030 mm - Weight with control cabinet: 2220 kg - Color: RAL 7035 light gray - Operating side: left to right - Ex version: No - Location: at the Blomberg warehouse

Condition: used, Year of construction: 1987, Edge grinding machine Manufacturer: Rehnen Type: R1 Year of manufacture: approx. 1987 Dwodpfezuzddox Agfob Technical data Work table: 1100 x 500 mm Grinding belt: 2280 x 150 mm 3 kW main motor 6.4 Amps Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2010, - Perfect for surface finishing - Constant working height - Q/L/Q Fine/cross-sanding machine Manufacturer: Weber Type: KSF-3-1350 Year of manufacture: 2010 Technical data - Equipped with 3 sanding belts for high-quality fine, veneer, and high-gloss sanding. - With a constant working height Machine frame Dwjdpezuzctjfx Agfjb - Heavy-duty steel welded construction for mounting 3 sanding units - Constant inlet height of 900 mm - Control and sanding belt change side on the inlet side, on the left - Stepless feed speed of 3-18 m/min, frequency-controlled. - Vacuum version of the conveyor belt / with 1 vacuum blower 5.5 kW, and a vacuum channel up to the upper edge of the machine Unit 1: Cross-belt unit - Pressure pad belt with felt and graphite for long service life - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Unit 2: CBF combination unit - One grooved rubber contact roller 0 130 mm, rubber hardness 60 Shore - One cross-running flap band with separate drive 4.0 kw - ISA segmented pressure bar system with 11 mm workpiece detection and 22 mm pressure pad width (counter-rotating) - Workpiece-controlled oscillating sanding belt blowing device Unit 3: Cross-belt unit - ISD segmented pressure bar system with 11 mm workpiece detection and 44 mm pressure pad width - Workpiece-controlled sanding belt blowing device Operator terminal SIEMENS" MP 377 12" Multi-Panel - Graphical user guidance via 12" color display - Program memory with 300 programs - Setting of all parameters via program WEBER i-Touch control - One rotary knob for navigating through the most important functions WEBER AWDM - Automatic thickness adjustment at the machine inlet with start switch Overthickness - Selector switch at the machine inlet with the following functions: - Automatic lifting of the contact roller and the segmented pressure bars - Feed stop ISA/ISD control - High-resolution workpiece detection in a 22 mm grid - Free loading of complex part shapes - Multiple loading with a small lateral distance - Sanding intensity individually adjustable at all edges - Sanding pressure adjustable via program ISA segmented pressure bar system (Unit 2) - Pressure pad movable in the longitudinal and transverse direction ISD segmented pressure bar system (Unit 1+3) As ISA, but additionally with - Separate adjustable pressure for the edge area (higher or lower) - Optionally only on the outer edge or outer and inner edges - Longitudinal and transverse edges or only longitudinal edges can be adjusted Workpiece blowing device - with WEBER ES system - Energy-saving, workpiece-controlled workpiece cleaning with single slider control WANDRES-Micro-Cleaning (single brush version) - Power sword brush with integrated micro-humidification of the linear brush (for optimal paint dust removal) Technical data - Working width: 1350 mm - Drive Unit 1 (frequency-controlled-Eco-Drive): 15.0 kW - Drive Unit 2 (frequency-controlled-Eco-Drive): 20.0 kW - Drive Unit 3 (frequency-controlled-Eco-Drive): 15.0 kW - Drive CBF: 3.0 kW - Drive vacuum blower: 5.5 kW - Drive feed (frequency-controlled): 3.0 kW - Drive height adjustment (frequency-controlled): 0.75 kW - Sanding belt speed (frequency-controlled): approx. 3-20 m/s - Sanding belt dimensions cross belts (W x L): 2x150x5100 mm - Sanding belt dimensions wide belt (W x L): 1370x2620 mm - Workpiece thickness (min./max.): 4-140 mm - Working height (constant): 900 mm - S

Condition: used, Year of construction: 2017, - 4 belt grinding units - Frequency control for all units - Electronic grinding pressure control Universal edge and profile grinding machine Manufacturer: Heesemann Type: UKP 20 Year of manufacture: 2017 Technical data Workpiece transport system - Total length: 5015 mm - Driven by a 1.5 kW three-phase motor with a double chain for workpiece transport - Feed rate in the range of 5-25 m/min, frequency-controlled - Working height constant at 880 mm - incl. integrated control cabinets - incl. adjustable guide rail with digital display and incl. counter rail with central width adjustment 4 lateral guide rollers between the grinding units for secure transport of workpieces Industrial PC 10.4" - LCD-TFT color display - Touch screen version - with display for production and downtime - with program memory for 100 programs 2 belt grinding units "M 4" Pos. 1 and 2 - for grinding straight edges - Belt dimensions: 2300x80 mm - Belt speed: 0.7-12 m/s - Motor power: 3.0 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 2 oscillation units for "M4" (Pos. 1+2) For complete utilization of the grinding belt 2 belt grinding units "K 4" Pos. 3 and 4 - for grinding small profile sections - can also be used for edge breaking - Can be swiveled 90 degrees upwards and 45 degrees downwards - Belt tear switch Dwedpfxezuzb Aj Agfeb - Tool holder with quick-change device - Intermittent belt extraction device - Belt dimension: 2000x50 mm - Belt speed: 0.5-8 m/s - Motor power: 1.1 kW - with electronic frequency control for stepless control of the belt speed - Electronic grinding pressure control from the terminal 4 electronic control units - for the fully automatic timing of the lowering and raising of the grinding tool, depending on the set feed rate, the grinding pressure and the unit angle setting Note: The technical data and descriptions are copies of the original order confirmation. The information is provided for informational purposes only and is not binding.

Condition: used, Year of construction: 2021, - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control Automatically Calibrating Sanding Machine Manufacturer: SCM Type: DMC system Year of manufacture: 2021 Technical data - Working width 1,350 mm - Belt feed speed 2 to 16 m/min - PRO SAND electronic control - PLC terminal with 10.4" LCD color display Unit 1 TIE 5000 working unit for additional table, internal cross-padding - Sequencing system of the unit for belt change by only one machine operator - Automatic brake - Linear blower with timed activation for belt cleaning - Belt dimensions: 150 x 5,000 mm - Chevron belt dimensions: 140 x 4,710 mm PE16T EPICS electronic sector sanding, pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Motor with inverter power up to 15 kW Unit 2 DO19 orbital unit for 19 rotating disc brushes - Manual adjustment of the unit's working position - 1.1 kW main motor with inverter drive - Independent motor for controlling the orbital movement - Diameter of the rotating disc: 125 mm FT/19/125 Set with 19 rotating discs, diameter 125 mm Unit 3 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 4 BF300 working unit for brush roller, diameter 300 mm - Manual adjustment of the roller's working position - 4 kW main motor with inverter drive FT 300 brush roller, diameter 300 mm Unit 5 SC 2620 working unit for super finish pad - Rotation of the belt in the opposite direction of the conveyor belt - Electronic belt swiveling control - Disc brake - Chevron belt dimensions: 1,370 x 2,186 mm - Belt dimensions: 1,370 x 2,620 mm PE16/C EPICS electronic sanding block with sector pitch 16 mm - 16 mm distance between sectors from center to center - Double-acting pneumatic cylinders with adjustable feed/counter feed - Graphite cloth with quick extraction device - Complete management of functions via the electronic Pro Sand control - Inverter motor with a power of up to 15 kW Inverter-controlled vacuum motor integrated into the machine frame, up to 7.5 kW - Rubber-coated conveyor belt, 50 Shore - 4 kW conveyor belt motor with inverter drive Console with integrated PC eye-M and electronic Maestro Pro Sand control with tele service system Device connected to the machine that enables the use of the Maestro Pro Sand software. The integrated LED light strip enables the operator to monitor the machine's status in real time (emergency, operation, etc.) without having to be near the machine itself. It is equipped with a fanless industrial PC with protection class IP53 (IP65 on the front). This robust solution guarantees the highest level of resistance even under the most adverse environmental conditions that an industrial site can offer. The 21.5" LCD color display with a large 16/9 touchscreen enables particularly easy and efficient control of the machine's most important functions: - Full HD display resolution 1920x1080 Dwodpfxezuzbce Agfeb - LED backlight - Capacitive

Year of construction: 2002, condition: used, functionality: limited functionality, Sand processing plant for the production of high-quality sand with a grain size of 0-2 mm. For sale is a complete sand processing plant from the Rheinstetten-Forchheim gravel and sand works of Heidelberg Materials Mineralik DE GmbH. The plant was used for cleaning sand, removing organic contaminants, and producing sand with defined quality characteristics. Key technical data: Throughput capacity up to 200 t/h Processing of sand 0-2 mm Production of controlled sand 0-2 mm allflux® AFX-F 750 fluidized bed classifier Solid material throughput up to 200 t/h Mixture volume approx. 375 m³/h Machine weight approx. 8 t allflux® AFS-F 500 eddy current classifier Solid material throughput up to 60 t/h Grain size 0-0.25 mm Fine sand recovery with hydrocyclones 3 dewatering screens for fine, medium-fine, and coarse sand Reversible conveyor belts Silo system with 6 buffer silos, each with a capacity of 220 m³ Dosing system with 8 dosing belts and 8 electric discharge gates Dsdpfxszx Uytj Agfowb Scope of supply: allflux® AFX-F 750 fluidized bed classifier Fine sand recovery with hydrocyclones and arch screen allflux® AFS-F 500 eddy current classifier 3 dewatering screens Fine sand recovery for coarse sand Fine sand recovery for medium-fine sand Conveyor technology Silo system Dosing system

Year of construction: 1991, condition: used, weight 240 kg max 50 mm ja serial number 2035 Dwodpsztfvbjfx Agfeb

Year of construction: 2012, condition: used, Control system with VIET IPC CONTROL color display Terminal with the possibility of memorizing program positions Automatic adjustment in real time of all the parameters necessary for processing Automatic positioning of the working thickness with gauge TM version with moving heads and fixed table (suitable to be placed in line) Feed speed from 3 to 16 mt / min Working width 1350 mm Abrasive belt length 7400 mm Dwedpfjgnz N Njx Agfjb Working height 3 - 160 mm No. 3 working groups: * Adjustable transversal sanding unit with electronic pads T42 ET 150x7400 with 15kW motor with inverter * Adjustable transversal sanding unit with electronic pads T42 ET 150x7400 with 15kW motor with inverter * Panel cleaning group in output Conveyor belt with 3kW motor with inverter Rubber conveyor belt perforated by depression Depressor for conveyor belt

Condition: used, Year of construction: 1995, Constant machine - combination station, dust brush - thickness measuring device - electronic segmented sanding pad MCS System Weber 32 mm - grooved steel calibrating roller - belt blow-off - vacuum conveyor belt. Sanding width: 1100 mm Drive: 15 kW Feed approx. 1.1 kW Height adjustment 0.25 kW Sanding belt dimensions: 1150 x 2500 mm Max. workpiece thickness: 150 mm Machine width: 1700 mm Machine length: 2000 mm Machine height: 2160 + 150 mm Machine weight: 1900 kg Constant working height: 850 mm Extraction connector: belt 180 mm / brush 120 mm Suction air volume: 0.74 m³/s Connected load: 23 kW Compressed air supply: 7 bar Feed speed: 3-15 m/min. Operating hours: 7000 h Location: Nattheim Dsdpfx Agex Twcpjfewb

Condition: used, Year of construction: 1997, incl. 3-roller feed motor: 2.2 kW, electric oscillation, belt speed: approx. 22 m/s, height-adjustable grinding table, table size: 1000 x 350 mm, continuously adjustable pivoting grinding unit from 0 - 45°, angle scale and mechanical lock, fold-up veneer edge sanding device, aluminum sanding shoe, height-adjustable radius sanding table, central dust extraction connection: 140 mm diameter, sanding belt: 3000 x 150 mm. Dwedpfx Aoy Dd Igogfsb Location: Nattheim

Condition: used, Year of construction: 1994, Belt height: 150 mm Belt length: 2280 to 2290 mm Belt speed: 22 m/s Two-sided sanding with oscillation Drive mechanism Veneer sanding mechanism End-face sanding / radius sanding with a small support table Surface sanding with a tilting table Belt direction: right/left Dwjdpfxszd Hngs Agfjb Location: Nattheim

Condition: reconditioned (used), Year of construction: 2006, year of last overhaul: 2026, ⚙️ STUDER S30-1 CE – High-precision cylindrical grinding machine | Complete retrofit We offer a STUDER S30-1 CE for high-precision external and internal cylindrical grinding operations. The machine has undergone a complete retrofit by MIRA Retrofit, including the inspection and refurbishment of its main components, as well as a careful adjustment and fine-tuning process. The result is a machine that is ready for operation, with a high level of precision, reliability, and stability, and performance comparable to that of a new machine. Key specifications: Dsdpfx Agezuzylefowb 🔹 Distance between centers: 650 mm 🔹 Height between centers: 175 mm 🔹 Grinding: external and internal 🔹 Condition: complete retrofit – ready for operation 🔧 Inspection and fine-tuning All components have been carefully inspected and adjusted to ensure high geometric accuracy and reliable, stable operation. 📸 Photographs of our finished machine. 🚚 Available for immediate delivery. For more information, technical documentation, pricing, or any questions about the machine, please do not hesitate to contact us. MIRA Retrofit SA

Condition: new, Year of construction: 2026, functionality: fully functional, machine/vehicle number: VG033-25dv, grinding width: 600 mm, grinding height: 530 mm, New, unused SAND1 beam sanding machine, available due to a change in company policy; it was never unpacked. Ideal for sanding beams with a cross-section of up to 600 x 530 mm. Provides a perfect finish. Capable of sanding unplaned wood. Sands on the lower surface. Top belt with pneumatic lift and automatic centering according to the size of the piece. At the base, a series of free-rotating rubber rollers to prevent damage to the wood surface. The machine can be operated in both directions, eliminating the need to flip the beam; simply lay the beam down. Top belt with pneumatic lift and automatic centering according to the size of the piece. LOWER SANDING UNIT Cushioned, suitable for beams, with a belt length of 1,900 mm. The pad is equipped with a timed inlet controlled by a PLC. High-power motor (11 kW) with fixed speeds and oscillation of the sanding belts. Dodpfjzh Hr Tex Agfowb 2 suction ports, 120 mm in diameter. ELECTRICAL CABINET integrated into the machine frame. All components are of the highest quality and supplied by international companies to ensure easy availability in the market. CONTROL PANEL equipped with a 7.5" TOUCHSCREEN programmer for managing all machine functions. Technical specifications are provided in the attached PDF. Includes 4 roller conveyors, 3 x 0.6 meters.