Used Offset Papier for sale (752)

Condition: ready for operation (used), Year of construction: 2019, travel distance X-axis: 1,016 mm, travel distance Y-axis: 660 mm, travel distance Z-axis: 635 mm, controller manufacturer: HAAS, table load: 1,814 kg, overall weight: 7,485 kg, spindle speed (max.): 10,000 rpm, spindle motor power: 44,700 W, number of slots in tool magazine: 30, number of axes: 3, This 3-axis HAAS VF-3YT/50 was manufactured in 2019. It features an impressive X-axis travel of 1,016 mm, Y-axis travel of 660 mm, and Z-axis travel of 635 mm. The machine is equipped with a high-performance spindle capable of 10,000 rpm and a 30-position automatic tool changer. If you are looking to get high-quality machining capabilities, consider the HAAS VF-3YT/50 vertical machining centre we have for sale. Contact us for further details. • Condition: Used, fully operational • Operating/cycle hours: 6,744 h • Spindle/cutting hours: 4,454 hTravels • Spindle nose to table: 201–836 mm Knsdpfxozwd Auj Aamjc • Rapid traverse: 18 m/min • Maximum cutting feed: 12.7 m/minSpindle and tool changer • Maximum torque: 460 Nm • Drive system: Vector drive with 2-speed gearbox • Tool changer capacity: 30 toolsTable • Table size: 1,372 × 610 mm • T-slots: 7 • T-slot width: 15.9–16 mmShipping • Note: Dimensions listed as 1,370 × 660 × 630 mm are not overall machine dimensions • Export shipping dimensions (approx.): 3,970 × 2,600 × 3,230 mm • Approx. shipping weight: 7,485 kg Additional equipment • Chip conveyor with four additional augers • Haas Chip Lift • Through-Spindle Coolant (TSC), 300 psi / 21 bar • Programmable coolant nozzle • Coolant chiller • ACF 25-micron auxiliary coolant filter • Coolant mist condenser • Minimum Quantity Lubrication (MQL) • Automatic air gun • Through-Tool Air Blast (TAB) • PulseJet system • Renishaw Wireless Intuitive Probing System (WIPS) with probe riser block • Fourth-axis drive and wiring • High-Speed Machining (HSM) • DWO/TCPC (Dynamic Work Offsets/Tool Center Point Control) • RTAP-3 synchronized tapping • Wi‑Fi network connection and Wi‑Fi camera • Automatic door • High-intensity lighting • Approximately 15 tool holders • Complete documentation Technical Specification Taper Size ISO 50

Condition: ready for operation (used), Year of construction: 2007, operating hours: 21,500 h, travel distance X-axis: 1,000 mm, travel distance Y-axis: 900 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: OKUMA, controller model: OSP-200M, spindle speed (max.): 6,000 rpm, number of slots in tool magazine: 150, number of axes: 4, This 4-axis Okuma MA-600HB was manufactured in 2007. It features a maximum spindle speed of 6000 RPM and a robust tool capacity of 150 tools in the automatic tool changer. The machine is equipped with a 30 bar coolant system and includes advanced features such as tool breakage control and DNC DT. If you are looking to get high-quality machining capabilities, consider the Okuma MA-600HB horizontal machining centre we have for sale. Contact us for further details. • Spindle: 30 bar through-spindle coolant • Control/Options: DNC/DT, MOP-Tool • Functions: Tool breakage control, Tool length offset Additional equipment • Renishaw MP10 probe • Robot interface type E • Mayfran MT10 chip conveyor Kedpfx Aaezx Dypomjnc

Condition: as good as new (ex-display), functionality: fully functional, input voltage: 400 V, input frequency: 50 Hz, workpiece height (max.): 60 mm, workpiece width (max.): 60 mm, workpiece length (max.): 140 mm, feed rate X-axis: 12 m/min, with approximately 4000 m of operating distance. Comes with a new machine warranty. The machine is sold without the depicted return system. The minimum workpiece width varies depending on the workpiece length, height, and surface quality: 70. Processing of roll material in thick PVC/ABS from 0.4–3.0 mm & strip material with a thickness of 0.4–12 mm. “e-motion” control system with an 18” touch-color screen with integrated maintenance software and available network connection. Stable machine stand made of steel. Extendable workpiece support facilitates working with large workpieces. Motor-controlled, positionable pressure bar with 2 offset arranged roller guides for even pressure distribution on the workpiece. Chain feed with rubberized support pads for optimal hold on the workpiece. Ball-bearing roller support plate with Ø 770 mm. Feed guide rail with sliding rollers for sensitive materials. Edge trimming unit with tool-controlled diamond cutters and 2 motors each with 1.5 kW, 12000 rpm. Chip removal is adjustable from 0–3 mm via motor-controlled positioning, including 2 diamond cutters Ø 80 mm, H 49 mm, Z2+2. Edge detection using an infrared sensor. Shear cutter for pre-capping thick PVC/ABS edge materials. Teflon-coated gluing unit with a capacity of 1.5 kg, application via a finely adjustable glue roller & quick-change system, as well as heating cartridge monitoring (~ 250 m/min per 1 kg of granules on a 19 mm board). Reversing function for the glue tank. Ideally suited for applying solid wood edge strips or laminate edges. Pneumatically tool-controlled gluing unit. Motor-controlled, positionable pressure unit with 1 large driven pressure roller and 2 conical follow-up rollers, pneumatically pre-tensioned. Cutting saw unit with 2 independent motors each with 0.50 kW, 12000 rpm, pneumatically swiveling 0–15°. Multi-function trimming unit for radius, flush and chamfer trimming of thin edges with 2 independent motors each with 0.75 kW, 12000 rpm, motor-controlled edge adjustment & pneumatic retraction function from the control panel. Corner processing unit for soft- and post-forming workpieces for processing the end edges with 0.4–3.0 mm edge thickness & 10–60 mm workpiece height. 2-axis motor-controlled, positionable radius drawing blade unit including pneumatic retraction function. Polishing unit with 2 motors. Special equipment 020 Surface drawing blade, pneumatically tool-controlled 032 Spray device for cleaning agents before the polishing unit 042 Spray device for release agents on the machine infeed side (PUR adhesive) 046 Extended feed guide rail (+400 mm) 047 Edge trimming cutter with interchangeable inserts, 64 mm height instead of 49 mm, 2 motors each with 2.2 kW instead of 1.5 kW 051 Multi-function trimming unit with vertical multiple rollers for processing workpieces with pot-band holes 053 Spraying of lubricant Pneumatic-mechanical insertion lock to prevent premature feeding of the machine 059 Automatic lubrication for the chain conveyor 064 Pneumatic-mechanical insertion lock 067 Reversing function for the glue tank. Ideally suited for applying solid wood edge strips or laminate edges. 050A Additional interchangeable glue tank, counter-rotating 090 “classic” multi-function & radius drawing blade unit e-motion with radius 1+2 mm Kjdpfx Aaszcymhomsnc 071 Motor-controlled adjustment and positioning for corner rounding cutters 085 Preparation for u-motion professional 033 LED lighting 505 Exhaust distributor professional Includes delivery & inst

Condition: used, Year of construction: 2019, Second-hand machine Year of manufacture: 2019 Only 110 operating hours! Features and technical specifications: Machining paths: - X = 1800 mm - Y = 900 mm - Z = 80 mm Made from 18 mm Koskisen boards Milling bed made from 19 mm MDF as a sacrificial plate with guide rails and slot blocks, used as a clamping method. Base frame with bracing, cast in polymer concrete, prepared for transport by pallet truck or forklift. Mechanical kit comprising profile guides including guide carriages, as well as ball screws 2010 and 1605 for all axes. Shaft couplings and high-performance grease for lubricating the individual carriages, as well as energy chains including connection sets. Control kit comprising a Triple Beast for controlling 3 axes, with an Ethernet connection. Leadshine driver board for the fourth motor. Four stepper motors, 5.0 A, 3 Nm, with motor cables, plus a switching power supply rated at 48 V, 6.7 A, LED board for breakout board, ribbon cable and proximity sensors, small parts such as wires, wire end ferrules, control cable, heat-shrink tubing and cable lugs. Fully installed in an aluminium housing, including electrical kit and emergency stop. - 21.5-inch monitor as a built-in display, including a mini PC with Windows 7, Rhino 5.0 CAD software, Estlcam G-code generator, Beamicon2 control software, as well as a mouse and keyboard, pre-installed in an ergonomic console. Knodpezk Npgsfx Aamjc Tool length sensor for determining the length and adjusting the active zero-point offset. Optional extras: - High-frequency spindle with 2.2 kW, including union nut, frequency converter, mains filter, braking resistor and collet set. - PC with 8 GB RAM and AMD processor - Rhino 5.0 CAD software for creating both simple 2D data and 3D solid models Availability: at short notice Storage location: Flörsheim

Condition: used, Second-hand machine Features and technical specifications: Drilling unit comprising a drilling motor with a holder for threaded drill bits with the option to accommodate 6 drill bits in accordance with the drilling pattern of which 5 are for a row of holes spaced 32 mm apart and 1 is offset to the rear at a distance of 32 mm from the Row of holes, e.g. for Häfele Varianta with roller conveyors to the left and right of the drilling machine Knedpozk N Trefx Aamec Availability: at short notice Storage location: 63934 Röllbach

Condition: new, max. tool diameter 400 mm 0 180 mm operating pressure 2 bar ROTATHERM chamber washing systems are used in all areas of industry and Craftsmanship for cost-effective cleaning of a wide variety of items to be cleaned and materials used. The parts are cleaned like in a dishwasher. Inserted into one Wire mesh basket they are in the closed device with a hot Lye shower washed from all sides. The machine will be selected after the Temperature and washing time set in operation. A centrifugal pump promotes the Washing water circulates to the nozzle system, which at the same time moves the basket in offset rotation. (Optional electric basket drive) After the cleaning process is complete, the device switches off automatically. the Parts can also be removed beforehand. In this case, when lifting the the pump is automatically put out of operation. ROTATHERM chamber washing systems are available in various sizes and at short notice Designs are available and can be requested on special claims be modified. As a rule, water-based cleaners are used deployed. But solvents are also used in ours cleaning machines. If necessary, the systems can be ex-protected version are delivered. Technical details EMSA ROTATHERM Mini: ----- Basket diameter: 400 mm Usable height: 180 mm Load capacity: 50kg Spray pressure without / with filter: 1.5 / 2.3 bar Circulation volume: 2.5 m³/h Tank capacity: 35 l Heating power: 2 kW Connected load: 2.5 kW Voltage: 220/230V Frequency: 50Hz Dimensions ----- Depth: 530mm Width: 650mm Height: 630mm Weight: 48kg ----- Price of the basic machine in the above design: On request! ----- Accesories: ----- Order No.: 1.521 Raised lid/max. Tool length 310 mm Kjdpfx Aajyrtytsmjnc Order No.: 1.522 HSK 63 F tool holder for changing with basket Order No.: 1.523 HSK 63 E tool holder for changing with basket Order No.: 1.524 Tool holder for Weinig Powermat to change with basket Order number: 2.006 small parts basket, Order number: 1.504 filter system (0.08m²), Order number: 1.510 pressure gauge, Order No.: 1.511 Electromotive basket drive, Order number: 1.512 mobile frame, Order number: 1,513 rolls, Order number: 1.514 suction device, Order number: 1.516 oil separator / belt skimmer, Order number: 1.518 system completely in stainless steel, Order number: 1.519 nozzles in stainless steel, ----- Price on request The ROTAHTERM tool washing machine is also available in larger versions Standard, Maxi and XL available. All devices are also available in special voltages. Surcharge on request. When ordering accessories, the specified technical data and possibly the delivery time! The values ??given are guide values. Construction changes reserved. Delivery time: short term and after Agreement. All prices ex works plus packaging, transport, insurance and legal VAT. (technical information according to the manufacturer - without guarantee!)

Condition: used, overall weight: 34,000 kg, axle configuration: 3 axles, first registration: 12/2020, Equipment: ABS, FFB semi-trailer with silo, model EUT 60.3-4/4, for the transport of feed, approx. 60,000 liters volume, 4-chamber aluminum design. Rated for a trailer total weight of 34,000 kg: 10 tons saddle pressure, 24 tons axle load technically permissible, 13 tons saddle pressure, 27 tons axle load (3 x 9 tons). Unladen saddle height 1250 mm. Container design: Container with 4 chambers, approx. 8,000 / 19,000 / 17,000 / 16,000 liters volume. Pressure equalization via elongated holes in the partition walls. 4 material discharge cones with special FFB material discharge bowls, DN 800 / DN 1000. Fluidization via special fluidization valve, manufacturer OLI. Operating parameters: The pressure vessel complies with the EC Pressure Equipment Directive. Operating pressure 2 bar, test overpressure 3 bar. Wall thickness approx. 5 mm. Operating temperature -40 to 80°C. 5 manholes DN 450 with pivoting and folding dome covers. Material discharge: For each material discharge cone, a central material sump with a diameter of 200 mm. The sumps are equipped with bottom flaps DN 200 with an aluminum housing, steel plate and stainless steel shaft, NBR seal (white), which are operated laterally via remote controls. A 4" material collection line made of special steel is collected on the left side on the operating side in front of the axle unit. Chamber 1 and 2 collected in front of the axle unit and chamber 3 and 4 collected behind the axle unit. At the end of each material line, a 4" annular nozzle is installed for material acceleration. A 4" sight glass is installed behind each annular nozzle. Material discharge via one 4" TW coupling with a blank cover. Agitation nozzles in the sumps. Air piping: An aluminum air collection line is mounted on the left side on the operating side and runs to the rear with a Storz B coupling. Ladder and walkway: One stainless steel access ladder on the front and one on the rear, left side. Aluminum safety walkway on the left. Brake lock when the safety guardrail is raised. Chassis: The saddle plate is equipped with a tested 2" kingpin. Suspension: Axle unit, manufacturer SAF, type INTRADISC PLUS II INTEGRAL, 3 x 9 tons, disc brakes ø 430 mm. The air-sprung axle unit is mounted in FFB aluminum suspension. Axle spacing 2 x 1310 mm. First axle as a lift axle, controllable from the driver's cab, with starting aid. Third axle as a trailing steering axle, lockable via reverse gear and additionally via a switch on the control panel. Braking system: 2-sensor 2-module SLV ABS/EBS pneumatic braking system equipped with a spring-loaded parking brake on two axles. RSS - Rollover Stability Support. Air suspension system: Air-sprung suspension with automatic height adjustment. Lifting and lowering valve mounted laterally on a control panel in front of the first axle. Tires: 6 tires, size 385/65 R22.5, are installed. Rims: Forged aluminum rims, manufacturer Alcoa, type Dura Bright EVO, size 22.5 x 11.75. Offset: 120 mm. Wheel bolt holes: 26 mm. Wheel cover: Single-wheel plastic mudguards, black, attached with stainless steel brackets. Mud flaps mounted on the rear mudguards. Electrical system: 24-volt electrical system consisting of: - a 15-pole socket mounted in front of the saddle plate. - two multi-chamber lights integrated into the rear underrun protection. - yellow side marker lights. - outline lights at the rear. - license plate lights at the rear. - 4 work lights, 2 x left at the discharge (switched via parking lights and additionally via a sw Ksdpfxezr A R Hj Aamsnc

Condition: used, mileage: 55,000 km, power: 390 kW (530.25 HP), first registration: 03/2025, fuel type: diesel, overall weight: 18,000 kg, color: grey, gearing type: automatic, Equipment: soot filter, Vehicle number: 1424766004 Knsdpjwflwljfx Aamec 1st owner, accident-free, full service history, non-smoker ---- Additional Features * We also offer financing, leasing, and rental options! * LA1 & LA2 7146 MOONSTONE GREY METALLIC * LZ2 FULL PAINT FINISH * C1W WHEELBASE 3700 MM * W9Z WEIGHT VARIANT 18.0 T (7.5/11.5) * M3E ENGINE OM471, R6, 12.8 L, 390 KW (530 HP), 2600 NM * M4X ENGINE VERSION EURO VI, E * M8B AIR INTAKE, BEHIND CAB, MOUNTED * M7K RADIATOR BLIND * M7T CONTROLLED WATER PUMP * M5V HIGH PERFORMANCE ENGINE BRAKE * M6M TWO-STAGE, CONSUMPTION-OPTIMIZED AIR COMPRESSOR * G5A SINGLE-PLATE CLUTCH * G2E TRANSMISSION G 281-12/14.93-1.0 * N6Z TRANSMISSION OIL COOLING * G5G MERCEDES POWERSHIFT 3 * G5L POWERSHIFT ADVANCED * G0K DRIVE PROGRAM ECONOMY/POWER * N2E NA MB 131-2C, PUMP * Z5M PTO, SINGLE * Z5S PTO PUMP, BELOW FRAME UPPER EDGE * A1Z FRONT AXLE, CRANKED DESIGN * A1D FRONT AXLE 8.0 T * A2E REAR AXLE, RING GEAR 440, HYPOID, 13.0 T * A3D REAR AXLE WITH ACTIVE LUBRICATION, NON-REGULATED * A5G AXLE RATIO I = 2.412 * A1A FRONT AXLE AIR SUSPENSION * J3Z AXLE LOAD MEASURING SYSTEM * R5E ALUMINIUM RIMS 11.75 X 22.5, FRONT, DURA-BRIGHT, ALCOA * R2Y ALUMINIUM RIMS 9.00 X 22.5, DURA-BRIGHT, ALCOA * R0L CUSTOMER-SPECIFIED TYRES FRONT * R0Z WHEEL NUT COVERS * S1Y TYRE PRESSURE MONITORING * A1 W48KBA 75 2 X 385/65 R 22.5 TL HIGHWAY RR STEERING? K? * A2 F38LCB 75 4 X 315/70 R 22.5 TL HIGHWAY RR DRIVE? L? * CZW STEP PLATE ABOVE FRAME, EXTENDED * C5P BOLTED FRAME * C0G REAR FRAME OVERHANG 1050 MM * C6G STEERING, SERVOTWIN * C6I POWER STEERING PUMP, CONTROLLED * C7T REAR INTEGRAL END * K0T MAIN TANK, LEFT * K1N TANK 570 L, LEFT, 650 X 700 X 1450 MM, ALUMINIUM * K3W ADBLUE TANK 75 L, LEFT * K5M LOCKABLE TANKS * K5S PROTECTIVE CAP FOR ADBLUE DOSING SYSTEM * Z4O NARROW TANK CROSS-SECTION * Z4R HIGH TANK CROSS-SECTION * K8D EXHAUST SYSTEM, OUTLET RIGHT SIDE EXTERNALLY, HORIZONTAL * U2G EXHAUST BOX * C8B REAR AXLE MUDGUARD, 2550 MM VEHICLE WIDTH * C8H 3-PIECE MUDGUARD, WITH EC SPLASH PROTECTION * C8I SPLASH PROTECTION (EC), FRONT * C7F FRONT UNDER-RUN PROTECTION (ECE), ALUMINIUM * C8Y UNDERBODY PANELING, AERODYNAMIC * F7A BUMPER, CORNERS PLASTIC * F7C BUMPER, CENTRE PART WITH TOWING EYELETS * C8Z SIDE SKIRTS, AERODYNAMIC * Q4Z FIFTH WHEEL, LOW MAINTENANCE, GREASED LOCK * Q6J FIFTH WHEEL COMPACT, JOST JSK 40K * Q6G FIFTH WHEEL, WITHOUT MOUNTING PLATE * Q6Z FIFTH WHEEL ANGLE, WITH HOLE GRID * Q4L FIFTH WHEEL HEIGHT, H = 190 MM * H2C FIFTH WHEEL OFFSET +600 MM * Q0W FIFTH WHEEL FROM FACTORY * B2A DISC BRAKE, FRONT AND REAR AXLE * B1B ELECTRONIC BRAKING SYSTEM WITH ABS AND ASR * B1F HEATING, ELECTRONIC AIR SUPPLY UNIT * B1H ELECTRONIC AIR SUPPLY & CONTROL, MEDIUM * B4A CONDENSATE MONITORING FOR AIR SYSTEM * B4L COMPRESSED AIR TANKS, ALUMINIUM, COMPLETE * B5D TRAILER STABILITY ASSIST (TSA) * B5J BRAKE AND ELECTRICAL CONNECTIONS, LOW * B2X PARKING BRAKE, ELECTRONIC * B3K SECONDARY OIL RETARDER * F1J L-CAB GIGASPACE, 2.50 M, FLAT FLOOR * F1R L-CAB * F2A FLOOR VERSION, FLAT FLOOR * F2H CAB WIDTH 2.50 M * F2P CAB, 765 MM MOUNTING HEIGHT * F2X GIGASPACE * F4H CAB REAR WALL, WITHOUT WINDOW * F3C CAB SUSPENSION, COMFORT, AIR SUSPENDED * F3W CAB TILTING DEVICE, MECHANICAL-HYDRAULIC * F6D TINTED WINDSCREEN WITH SUN STRIP * F8V LIGHT SENSOR * F8W RAIN SENSOR * D8M ELECTRIC SLIDING/TILTING SUNROOF, GLASS DESIGN * F4X EXTERNAL STORAGE BOX, LEFT * F4Y EXTERNAL STORAGE BOX,

Condition: used, Year of construction: 2022, Horizon Booklet Production Line SPF-200L, FC-200L, VAC-600Ha, VAC-600Hm, VAC-600Hm, VAC-600Hc The Horizon booklet production line featuring the models SPF-200L, FC-200L, is a state-of-the-art, modular solution for the efficient production of saddle-stitched booklets – including A4 landscape format. The system is suitable for both offset and digital printing and is especially designed for small to medium print runs. Thanks to the combination of collating machines (VAC-600Ha, VAC-600Hm, VAC-600Hm, VAC-600Hc), booklet maker (SPF-200L), and front trimmer (FC-200L), the line offers maximum flexibility and productivity in post-press processing. Special Features - Automated Settings: All format and production parameters are automatically set via a large, intuitive color touchscreen – including fold roller gap. - A4 Landscape Capability: The SPF-200L enables the production of booklets in A4 landscape format, making it particularly versatile. - Modular Expandability: The VAC-600 collating towers are modularly expandable from 6 up to 60 stations and allow non-stop operation through double-cycle and insert programs. - High Speed: Up to 9,500 cycles/hour for collating and up to 4,000 booklets/hour for stitching (3,500 in landscape format). - Flexible Configuration: Can be combined with additional Horizon feeders and digital print feeders for hybrid production lines. - Versatile Formats: Processes formats from at least 148 x 120 mm up to a maximum of 610 x 350 mm (SPF-200L). - Robust Wire Processing: Various stitching heads available for different wire gauges and loop stitching. - Easy Operation: Large touchscreens on all main modules for rapid setup and error diagnosis. Technical Specifications - SPF-200L Format Range (min-max): min. 180 x 105 mm, max. 610 x 350 mm - SPF-200L Speed: up to 4,000 cycles/h (3,500 cycles/h landscape) - SPF-200L Features: A4 landscape, fully automatic - FC-200L Format Range (min-max): Front trimmer, integrated - FC-200L Features: Final trimming - VAC-600a/c Format Range (min-max): min. 148 x 120 mm, max. 500 x 350 mm - VAC-600a/c Speed: up to 9,500 cycles/h - VAC-600a/c Number of Stations: 6–60 - VAC-600a/c Features: Modularly expandable, non-stop - Booklet Thickness: up to 100 pages (depending on paper) - VAC-600 Loading Capacity: 55 mm per station - Weight SPF-200L with FC-200L: approx. 831 kg - Machine Dimensions SPF-200L with FC-200L: 4,271 x 810 x 1,250 mm (L x W x H) Ksdpextag Iefx Aamjnc - Power Supply: 230 V, 5.3 A; 1.0 kW (SPF-200L) All-Inclusive Service Package We take care of everything: from secure packaging and transportation to customs clearance. Upon request, we can also provide a customized leasing offer. Sustainable and Economical Choose a used machine and benefit twice: Save the environment and your budget. Despite possible signs of use, you receive a quality product at an attractive price.

Condition: new, Year of construction: 2026, Working width: 600 mm Working height: 300 mm Minimum workpiece length: 250 mm Units: 2 brush units, centrally adjustable electrically with fine offset adjustment 1st brush: Metal brush, diameter 210 mm 2nd brush: Tynex brush, grit 80, diameter 210 mm Knsdjxwnilepfx Aamec Height adjustment: electric Height display: mechanical counter Feed speed: 4 - 12 m/min Brush motor power: 2 x 4 kW Feed motor power: 0.37 kW Machine length: Machine width: Weight:

Condition: used, mileage: 314,000 km, power: 294 kW (399.73 HP), first registration: 04/2019, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: white, gearing type: automatic, emission class: euro6, Year of construction: 2019, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, tail-lift, We are very pleased that our offer has aroused your interest and would like to assure you that you can purchase a good and affordable vehicle with a transparent service history at our company! MB ACTRO 2540 COMPLETE RIG with certified BÖSE swing-wall bodies Rear cargo securing system 2 x LBW BÄR 2,500 KG Trailing axle RETARDER Special equipment: Front axle load 8.0 t, airbag driver's side, work lights, audio system: CD radio comfort (Bluetooth), exhaust pipe downwards to the right, brake connection standard and DuoMatic, compressed air connection in the cab, high compressed air unit, compressed air horn, electrical system and lights for swap body frames, cab: with air suspension, tinted windshield, vehicle without trailer coupling, info display 12.7 cm with video function, mudguards 3-piece, fuel tank: 290 liters aluminum, cool box / refrigerator, aluminum rims 9.00x22.5 (ALCOA matte), roof air deflector (lockable), 2-cylinder air compressor, enhanced engine brake, steered trailing axle, tire pressure control system, retarder, reversing warning signal (external warning), switch for loading platform, rear crossmember reinforced, interface for fleet management system, circuit breaker, seats in the cab: armrest co-driver's seat, seats in the cab: driver's seat comfort suspension seat, exterior sun visor, roller blind for side window, driver's door, 12V socket in the co-driver's footwell, additional 12V socket, 24V / 25 A socket in the co-driver's footwell, 24V socket in storage compartment on the right, automatic daytime running lights, preparation for rear view camera Additional equipment: Emission standard EURO 6, axle configuration: 6x2, Actros 4, trailer brake 2-line, connections on the left, trailer socket 24V / 15-pole, exterior mirrors electrically adjustable and heated, differential lock rear axle, steel compressed air tank, driver assistance system: Attention-Assist (fatigue detection sensor), driver assistance system: braking assistant (Active Brake-Assist), driver assistance system: lane keeping assistant, cab: width 2.30 m, cab: L StreamSpace, cab floor with engine tunnel 320 mm, suspension: air / air (full air), electric windows, generator 100 A, transmission 12-speed - type: G 211-12, urea tank (AdBlue): 60 liters, rear axle bevel gear 440, body / superstructure: chassis, lower comfort bunk, comfort locking system, communication interface, radiator grille, regulated power steering pump, engine 10.7 liters - 290 kW R6 diesel (OM 470), engine compartment encapsulation, trailing axle with single tires, ramp mirrors, waste heat recovery, disc brakes front and rear axle, seat cover / upholstery: fabric, seats in the cab: co-driver function seat, seats in the cab: driver's seat backrest foldable, voltage converter 24V / 12V 10 A, splash guard front, front axle stabilizer, additional stabilizer, rear axle / trailing axle, external storage compartment on the left, cab socket 24V, tachograph / EC control unit, door extension for the cab, aerodynamically shaped underbody panel, underrun protection front, preparation for CB radio, preparation for toll collection, front axle offset, regulated water pump, permissible gross weight 25.00 t, auxiliary heater (water) GERMAN VEHICLE REGISTRATION / CUSTOMS SERVICE We will organize your registration and the export documents / EUR 1 and manufacturer's declaration for export. FINANCING Upon request, we will be happy to provide you with a LEASING-RENTAL PURCHASE or FINANCING OFFER. Kodow R Ipyopfx Aamsnc SERVI

Condition: excellent (used), Year of construction: 1999, • FANUC 210i - T control (cycles) • Max. distance between centers: 1,250 mm • Max. turning diameter: 400 / 585 mm in offset • Spindle speed: 12 . . . 2,500 rpm • Spindle bore: 54 mm • X-axis: 210 mm Kodpfjw S E R Rsx Aamonc • Z-axis: 1,181 mm • Cutting gap adjustment: 0.05 – 0.8 mm • Motor power: 7.5 kW • Weight: approx. 2,700 kg

Condition: excellent (used), Format (cm): 32x46 All existing tools will be included with the device for punching and perforating as well as holders of these tools (see pictures) Knsdpoh Eikmsfx Aamec

Condition: not inspected (used), Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine Kjdst Tqy Ejpfx Aamenc with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: ready for operation (used), Year of construction: 2018, travel distance X-axis: 3,110 mm, travel distance Y-axis: 1,620 mm, number of axes: 4, number of slots in tool magazine: 11, spindle motor power: 10,000 W, spindle speed (max.): 24,000 rpm, This 4-axis SCM Morbidelli Author M100 CNC Wood Machining Centre was manufactured in 2018. It features a working area along the X-axis of 3110 mm and a maximum panel height of 180 mm. The machine is equipped with 21 vertical spindles and 10 horizontal spindles, providing versatile machining capabilities. If you are looking to get high-quality wood machining capabilities, consider the SCM Morbidelli Author M100 machine we have for sale. Contact us for further details. • Working area / axes: • Panel length (Y): 1900 mm (2210 mm) • Panel height (Z): 180 mm Knedpfx Aaez A Ahqomec • Panel length for through machining: 1400 mm • Vector speed X‑Y: Pro‑Space 56 m/min; Pro‑Speed 78 m/min • Worktable: 6–12 beams (TV Flex), 12 vacuum pods (145 × 145 × H75 mm); 2 stops per beam; movable beam length 1600 mm. • Drilling unit (general spec): • 21 vertical spindles, 8,000 rpm • 10 horizontal spindles, 8,000 rpm • Integrated saw Ø125 mm (X), 10,000 rpm • Motor power 2.2 kW • Electrospindle: 10 kW (S6), max 24,000 rpm. • Installation requirements: installed power 23–28.5 kVA; compressed air 450 NL/min; dust extraction 4500 m³/h, 25 m/s, outlet Ø250 mm. • Structure and motion: • Heavy, stress‑relieved, electro‑welded steel frame; all machining in single setup on CNC metalworking machines. • High‑speed four‑row linear guides; three‑circuit recirculating ball systems; X‑axis helical rack‑and‑pinion. • Brushless motors, inverters; machining units mounted on mobile gantry for rigidity. • Transparent polycarbonate safety enclosure. • CNC control and software: • PC‑Office: Windows 7, 17" color LCD, QWERTY keyboard, mobile control panel, Xilog Maestro. • Xilog Maestro features: parametric/graphical/ISO programming; DXF/ASCII import (2D); 3D linear/circular interpolation; spatial linear interpolation; helical interpolation; guided editor; automatic drilling optimization and tool libraries; panel origin offset; simulation; barcode management (software); self‑diagnostics; step‑by‑step manual intervention; graphical unit configuration; machining speed selection; SCM CNC Jerk function. • Safety: CE; PRO‑SPACE system with safety bumpers (automatic stop on potential collision). • Table equipment included/mentioned: rear aluminum reference stops H75 per beam; second central reference stops per beam; front reference stops H75 per beam. • Vacuum system: integrated vacuum pump 90/108 m³/h, 50 Hz. • F23 L drilling unit (listed configuration): • Independent Z‑axis • 13 independent vertical spindles (8 X / 5 Y) • 6 independent horizontal spindles (quick‑release), incl. 4 in Y • 32 mm pitch • Speed 4,500–8,000 rpm (inverter) • Rear‑panel groove/saw unit Ø125 mm, 5,500–10,000 rpm (inverter) • Motor 2.2 kW • Increased Z‑pressure • RO AX advantages: high productivity, precision, finish quality, processing speed; up to 90% reduction in maintenance (approx. 1,000‑hour interval). Additional equipment • TRB14 side‑mounted tool magazine (optional), right side: • Capacity up to 11 tools; max Ø350 mm • Center distance 130 mm • Max tool weight 8 kg; total 48 kg • 4 workpiece lifting supports H75, two lifting levels (above clamps and working level), 20 kg per support • Additional hardware key with USB port

Condition: good (used), Year of construction: 2017, operating hours: 6,240 h, functionality: fully functional, machine/vehicle number: 6700-112239, overall weight: 1,540 kg, load capacity: 245 kg, arm reach: 3,000 mm, This is an ABB IRB 6700-245/3.00 industrial robot with an IRC5 controller and an RW6 PC, manufactured in 2017. We would be happy to offer you this robot as a fully refurbished unit! Knedsz Ipywepfx Aamoc The controller includes the following options: VDPUC Driver RobotWare Base English 888-2 PROFINET Controller/Device 963-1 PROFIenergy 687-1 Advanced Robot Motion 603-1 Absolute Accuracy 988-1 RW Add-In Prepared 606-1 Conveyor Tracking 608-1 World Zones 610-1 Independent Axis 611-1 Path Recovery 612-1 Path Offset 885-1 SoftMove 1180-1 Tool Control 613-1 Collision Detection 614-1 FTP SFTP and NFS client 616-1 PC Interface 688-1 RobotStudio APP Connect 623-1 Multitasking 624-1 Continuous Application Platform 813-1 Optical Tracking 625-1 Discrete Application Platform 628-1 Sensor Interface 689-1 Externally Guided Motion (EGM) 1341-1 / 1520-1 Integrated Vision Interface 630-1 Servo Tool Change

Condition: good (used), Year of construction: 2017, operating hours: 6,925 h, functionality: fully functional, machine/vehicle number: 6700-111941, overall weight: 1,170 kg, load capacity: 200 kg, arm reach: 2,600 mm, This is an ABB IRB 6700-200/2.60 industrial robot with an IRC5 controller and an RW6 PC, manufactured in 2017. We would also be happy to offer this robot to you as a fully refurbished unit! The controller includes the following options: 709-1 DeviceNet Master/Slave 888-2 PROFINET Controller/Device 963-1 PROFIenergy 997-1 PROFIsafe F-Device 687-1 Advanced Robot Motion 603-1 Absolute Accuracy 988-1 RW Add-In Prepared 606-1 Conveyor Tracking 608-1 World Zones 610-1 Independent Axis 611-Path Recovery 612-1 Path Offset Knjdpfx Ajz Imldeamec 885-1 SaveMove 1180-1 ToolControl 613-1 Collision Detection 614-1 FTP, SFTP, and NFS client 616-1 PC Interface 688-1 RobotStudio APP Connect 623-1 Multitasking 624-1 Continuous Application Platform 813-1 Optical Tracking 625-1 Discrete Application Platform 628-1 Sensor Interface 689-1 Externally Guided Motion (EGM) 996-1 Safety Module 735-7 Keyless Mode Switch, 3 modes 1341-1 /1520-1 Integrated Vision Interface 630-1 Servo Tool Change

Condition: new, maximum load weight: 16,180 kg, overall weight: 20,500 kg, axle configuration: 2 axles, Equipment: ABS, You can find our complete vehicle inventory, including vehicles available immediately and in the short term, on our website. Excerpt from the equipment: Complete equipment available upon request. Chassis * Steel welded structure made of welded longitudinal beams and pierced Z-shaped cross members * Narrow cross member spacing for high ground load capacity * Ramp storage between the longitudinal beams behind the axle assembly * Two pockets below the loading platform for one ramp each * With locking plate in the head frame at the rear Under-run protection * Compliant with EC regulations Front bolster * Bolsters with single-sided operation * Rear support: Two adjustable drop-down supports Axles * 2 x 10 t air suspension axle assembly * Manufacturer: SAF * Drum brakes approx. 300x200mm * Center-mounted for twin tires, ABS * Total travel of the air suspension approx. 200mm * Of which lifting approx. 140mm and lowering approx. 60mm * Control via hand lever with detent function Knsdpfx Aajz Dmnkemec Tires * 8x, 235/75 R17.5 * Manufacturer of our choice * Mounted on rim 6.75X17.5 with offset Splash guards * Made of PVC in front of and behind the axles, compliant with EC regulations Load securing * One hole for lashing straps in the outer frame approximately every 150 mm * Tensile force approx. 2.5 t * 6 pairs of folding lashing rings evenly distributed, tensile force approx. 8 t * Recess pockets for lashing bars 80/50 * 3 pairs of recess pockets in the outer frame, evenly distributed. Braking system * Air brake system compliant with EC regulations with EBS * Two spiral hoses as connection to the towing vehicle with coupling head red/yellow * Spring brake acting on one axle. Floor * Approx. 28 mm Z-shaped hardwood floor recessed in the outer frame. Lighting system * Lighting system compliant with EC regulations, 24 Volt * Multi-chamber rear lights * License plate lights * Side marker lights and position lights at the rear * Connection plate on the left on the drawbar, incl. connection cable with 15-pin and 2 x 7-pin plugs. Painting * Chassis blasted, cleaned and hot-dip galvanized with state-of-the-art technology. * Superstructure parts cleaned, primed and hot-dip galvanized * Chassis: Hot-dip galvanized + RAL color of choice * Hubs: KTL black * Under-run protection: RAL 9010 Pure White * Rims: RAL 9006 Silver * Attached parts: galvanized / KTL * Black contour marking: acc. to EC, yellow on the side and rear (with ES-GE logo) Incl. accessories * Rear extension by approx. 800 mm incl. under-run protection * Extendable loading platform * Load capacity approx. 2 t, locking every approx. 200 mm * Mechanically adjustable fixed drawbar in length, 6 x approx. 100 mm * With screwed drawbar eye approx. 50 mm acc. to DIN 74053 * 4 rows of recess pockets transverse to the loading area, evenly distributed * 12 pieces of lashing bars made of galvanized tube, approx. 80/50/4 mm, approx. 1,000 mm long * Container locking for 1x20? container, container locking 1 x 20? extendable to approx. 2,820 mm, acc. to ISO 1496, EN 284 or EN 452 * 1 pair of aluminum ramps, load capacity per pair approx. 9,000 kg * 4 x stainless steel toolboxes between or behind the axles * 2 wheel chocks with holder * Rotating beacon pluggable at the rear * Delivery of a 40-unit towing device (GG max. 13,500 kg)

Condition: used, Year of construction: 2018, Overview This Krones Linatronic M is an empty bottle inspector for glass bottles, built in 2018. It inspects every empty container before filling and rejects any container that fails one of the inspection stages. The machine combines camera-based base, sealing surface, screw thread and sidewall inspection with high-frequency and infrared residual liquid and caustic detection. Two sidewall modules with four mirror assemblies and four cameras provide a compact full-front view of the container, and the DualFlash neck finish lighting inspects the outer and inner sealing surface separately using two minimally offset lighting angles. Foreign containers are identified at the machine infeed by height, contour and colour detection. Three Ecopush rejection points separate foreign, dirty and damaged containers. The machine is operated from a Krones iPanel CD terminal. Technical data - Manufacturer: Krones - Model: Linatronic M - Machine type: empty bottle inspector - Year of manufacture: 2018 - Application: inspection of empty bottles prior to filling; neck ring detection for returnable PET containers included - Inspection modules: base inspection, sealing surface inspection, screw thread inspection (cone optics), sidewall inspection - Sidewall inspection: 2 modules with 4 mirror assemblies and 4 cameras, two views per camera at 45° - Residual liquid and caustic detection: high frequency and infrared - Additional detection: polarising transparent films at container base and sidewall, glass fragments at the container base, scuffing via sidewall camera - Foreign bottle detection at the infeed: container height, contour and colour via camera - Rejection: 3 x Ecopush - foreign containers at the infeed, dirty containers and damaged containers at the discharge - Control: Krones iPanel CD operator terminal, prepared for data connection to a single-station PC (Datalyser) - Test bottle programme with 2D code - Conveyor height: 1,200 mm, adjustment range 1,155 - 1,315 mm - Minimum required room height: 2,810 mm - Overall dimensions: approx. 6,700 x 1,300 x H 2,800 mm - Direction of operation: right-left machine - Power supply: 400 / 230 V, 3/N/PE, 50 Hz, 6 A full load current, 20 A pre-fuse; auxiliary supply 230 V, 1/N/PE, 5 A - Standards: IEC 61439-1 / IEC 60204-1, CE marked - Machine base and housing: stainless steel (AISI 304 equivalent), clean design Equipment - DualFlash neck finish lighting, separate inspection of outer and inner sealing surface - Combined thread inspection via the sidewall mirror assembly - Fallen container detection in front of the machine (photoelectric sensors with infeed pusher) - Base blow-off unit with clocked air nozzle for foam and lubricant residues - Container blower at the infeed, conveyor dead plate (3-fold) - Servo-driven collection module for rejected containers at the discharge - Festo pneumatic system with maintenance unit, food-grade lubricants - Emergency mode: passage operation without inspection - OEM machine data sheet and dimension drawing Condition Knodpozy Ud Ijfx Aamjc Used, technically complete. The machine is still installed and under power at its production site; the photographs show it in the installed state. Availability Immediately. The machine will be dismantled and relocated to Germany. Viewing by arrangement; dismantling, loading and transport can be quoted on request.

Condition: used, maximum load weight: 14,900 kg, overall weight: 19,000 kg, axle configuration: 2 axles, first registration: 03/2015, loading space length: 5,100 mm, loading space width: 2,430 mm, loading space height: 1,000 mm, loading space volume: 12 m³, Year of construction: 2014, Equipment: ABS, ? Foldable under-ride protection ? ABS ? Duomatik air connection Knjdpfx Aaoz Dzn Ssmoc ? Front wind deflector ? Towing hitch with height adjustment via offset plate ? BPW axles ? 5-chamber tail lights Body: 3-sided tilting platform body, steel front and rear walls, steel floor, lashing eyes, spring-relieved aluminum side panels on the left and right (oscillating and foldable).

Condition: used, mileage: 13,063 km, power: 96 kW (130.52 HP), first registration: 12/2025, fuel type: gasoline, empty load weight: 1,761 kg, maximum load weight: 532 kg, overall weight: 2,368 kg, wheelbase: 3,100 mm, next inspection (TÜV): 12/2028, fuel: super 95, energy efficiency: C, CO₂ emissions: 170 g/km, fuel consumption (combined): 7.5 l/100km, color: black, driver cabin: other, gearing type: automatic, emission class: euro6, number of seats: 7, total length: 4,930 mm, total width: 2,160 mm, total height: 1,820 mm, Year of construction: 2025, maximum speed: 175 km/h, Equipment: ABS, air conditioning, airbag, central locking, cruise control, electronic stability program (ESP), fog lights, navigation system, onboard computer, parking sensors, power assisted steering, seat heater, second-hand vehicle warranty, sliding door, soot filter, traction control, trailer coupling, Exterior * Trailer coupling, fixed ball head * Sliding door, left side, with window * Sliding door, right side, with window * TIREFIT * Deletion of type designation * Door sill trims with "Mercedes-Benz" lettering Interior * Seat heating for driver and front passenger * Automatic climate control system Thermotronic * Luggage compartment cover * Luggage securing net * Headrests for passenger compartment seats * Glove compartment, passenger side, closed * Pocket on driver and front passenger backrests Safety * Automatic deactivation of front passenger airbag * Electronic Stability Program (ESP) * Airbag for driver and front passenger * Brake system with ABS and ASR * Heated rear window Comfort and Environment * Keyless-Go * Rear view camera * Hill-start assist * ECO start-stop function * High beam assist * Blind spot assist * Active Parking Assist * Particulate filter * Warm air duct to passenger compartment * Auxiliary heater, electric * Mercedes-Benz emergency call system * Leather steering wheel * Multifunction steering wheel * Cruise control * LED High Performance headlights * Light and rain sensor Multimedia * Live Traffic Information * Instrument cluster with color display * Digital radio (DAB) with Bluetooth hands-free system Equipment lines and packages * Special model Edition * Ambient lighting * Chrome interior package * Advantage package * Navigation package * Mirror package * Technology package * Winter package * Radiator grille, chrome-plated Condition/Documents * Certificate of Conformity (COC) documents Other * 17-inch light alloy wheels in 5-twin-spoke design * 2 USB ports in the center console, rear * 7-speed automatic transmission * 7-seater * Sliding door rail cover in vehicle color * Active Brake Assist * Active Lane Keeping Assist * Active Safety Package Knedpfx Aaoz Hd Sxjmoc * Armrest with storage compartment * Exterior mirrors, electrically foldable and adjustable * Exterior mirrors, painted in vehicle color * Front passenger seat, height-adjustable * Ventilation nozzles in the rear * Turn signal indicators in exterior mirrors, LED technology * Tinted glass in the rear, black glass * Digital extra: Extended MBUX functions * Digital extra: Hard disk navigation * Digital extra: MBUX Navigation Plus * Digital extra: Remote Services Plus * Digital extra: Smartphone integration * Individual seats in the 3rd row of seats * Individual seats in the 2nd row of seats * Electric parking brake * Electric window lifts in sliding doors * Emission class Euro 6e * Driver's seat, height-adjustable with lumbar support * Fixed rear window * Window in tailgate with wiper and washer system * Front electric windows with one-touch operation * Heated windscreen * Floor mats, velour * Weight variant 2,368 kg * Handle strip above license plate in vehicle color * Interior mirror Other: * Nationwide delivery for €399 net plus VAT (€474.81 incl. VAT). * For all vans: On request, 12 or 24 months Mercedes-Benz used car warranty is possible. * We will gladly take back your current vehicle, offset it against the new vehicle or pay you the purchase price. * Leasing / financing via Mercedes-Benz Bank. We will be happy to prepare an offer for you. * No liability for printing and typographical errors * Subject to errors and prior sale.

Condition: new, Year of construction: 2026, Robotic tray handling for deep-drawing systems – automated up to 120 cycles/hour JAC Automation & Robotics offers an automated handling solution for plastic trays that can be integrated into existing or new production facilities. The system takes over the automated handling of trays between the individual process steps, thereby significantly reducing the manual effort in production. The images shown are from an existing reference system that is currently in production. The system offered will be newly designed and built specifically for your application. Functionality: • KUKA industrial robots • product-specific gripper system • infeed and outfeed conveyor technology • automatic tray pick-up and placement • centering and positioning devices • control cabinet and system control • Siemens HMI for operation and recipe management • protective fencing and safety technology Depending on the product, different handling concepts can be implemented with clamping or suction grippers. The system can be flexibly adjusted to different tray variants via a recipe and parameter management system. Performance data: • Tray sizes: approx. 400 x 300 mm to 800 x 600 mm • Performance: up to approx. 120 cycles per hour Knjdpfjz D H H Tsx Aamec • different tray heights and product variants possible • automatic product changeover via recipe management • manual and automatic system operation • individual adaptation to existing production facilities The specified performance applies without pad printing and depends on the product, gripper concept, travel paths, and system layout. Optional extensions: • automatic stamping system • pad printing system • automatic deburring • turning device for trays • additional conveyor technology • buffer and stacking locations • additional inspection and processing stations The existing reference system combines robotic handling, conveyor technology, stamping, pad printing, and a separate deburring station, among other things. Operation and control: Different products and recipes can be managed via the central Siemens HMI. Product-dependent parameters and position corrections can be set directly via the user interface. The control system offers, among other things: • recipe management • automatic and manual operation • adjustable product parameters • offset corrections • system and robot diagnostics • error and message history • user management • maintenance overview Advantages: • reduction of manual handling operations • reduced personnel costs • reproducible process sequences • reduced risk of handling errors • consistent production quality • more ergonomic workplaces • flexible processing of different tray formats • easy expandability with additional process steps • integration into existing production lines Important note: The system offered is not the reference system shown in the pictures. Each system is newly designed and manufactured according to the customer-specific requirements, the existing machines and the products to be processed. Price: upon request Upon request, JAC Automation & Robotics will handle the complete implementation, from design and robot programming to control cabinet construction and assembly, to commissioning the system.

Year of construction: 2023, condition: new, PLASMA CUTTER MODEL MTX 2040 Construction: steel + aluminum Working area: 4000/2000/200 XY axis drive: double-sided gantry drive: 4Nm stepper motors with gearboxes, rack and pinion Z axis drive: stepper motor, ball screw Travel speed: up to 25 m/min Z axis control system: THC My plasm system Linear guides: TBI IGUS guide Automatic material detection system Power supply: 240V Permissible load: 2000 kg Total weight: 800 kg net USB port for opening projects and transferring files via external pen-drive Sheet detection system THC height control system TBI linear guides Double-sided gantry drive: X axis: stepper motor and rack and pinion Y axis: stepper motor and rack and pinion Z axis: stepper motor and ball screw Drives implemented using TBI HGR 20 rails Table equipped with a water table (water table, providing cleaner cutting, material cooling, and reduced gas emissions during processing) INCLUDED: - water table - replaceable grating - control program in Polish - CE declaration of conformity - technical documentation - warranty - commissioning and training included in the price The latest control system available in our cutters: Integrated THC height regulator Anti-torch dive function Accepted file types: DXF, PLT (hpgl), G-Codes (.tap) Integrated CAM module: MyMini CAM Automatic recognition of external objects Path analysis in advance Cutting parameter database Project angle correction to material Ability to cut from any location Ability to cut from the end Import DXF, PLT or G-CODES Automatic generation of paths with offset, entry and exit points The program can be used with an external CAM program Separate speed for holes Parameter database Project correction to the material layout angle Soft and Hardware limits THC anti-dive functions Game Pad control possible Material detection via touch system, floating head WHY IT'S WORTH IT WE ARE A POLISH MANUFACTURER OF PLASMA CUTTERS CLOSE COOPERATION WITH PROMA-ELEKTRONIKA (THC MANUFACTURER) Knedpfxjiphrle Aamec PROFESSIONAL GUIDES FROM THE RENOWNED HIWIN COMPANY; THESE GUIDES ARE CHARACTERIZED BY VERY LONG LIFESPAN, HIGH CUTTING QUALITY, AND DO NOT REQUIRE FURTHER PROCESSING COMPONENTS SUCH AS GEARBOXES, FASTENERS, HOLDERS, ETC. ARE MADE BY US USING CNC TECHNOLOGY, WHICH ENSURES HIGH QUALITY AND REPEATABILITY OUR STRENGTHS HIGH-QUALITY SHIELDED CABLES INDUCTIVE SENSORS ON ALL AXES, WHICH ARE NOT SUSCEPTIBLE TO DUST OR JAMMING ADVANCED THC MY PLASM, SMOOTH TORCH OPERATION CPC INTERFACE (VOLTAGE DIVIDER) MOUNTED IN CUTTERS WE MOUNT CUTTERS SUPPLIED BY THE CUSTOMER OR PURCHASE CUTTERS THAT MEET CUSTOMER REQUIREMENTS WE HELP IN ARRANGING LEASING Possibility to select the appropriate cutter to meet the individual needs of the company. We offer other table sizes.

Condition: used, functionality: fully functional, mileage: 198,186 km, power: 316 kW (429.64 HP), first registration: 03/2020, fuel type: diesel, empty load weight: 7,401 kg, overall weight: 18,000 kg, axle configuration: 4x2, wheelbase: 3,600 mm, axle spacing: 3,600 mm, fuel: diesel, fuel tank capacity: 480 l, brakes: retarder, color: blue, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: air, total width: 2,500 mm, permissible axle load (axle 1): 7,100 kg, permissible axle load (axle 2): 11,500 kg, Year of construction: 2019, Equipment: ABS, AdBlue, EBS, USB port, air conditioning, airbag, central locking, cruise control, differential lock, electric window regulation, electronic stability program (ESP), fog lights, full service history, hill-start assist, lane keeping assist, non-smoking vehicle, onboard computer, power assisted steering, power mirror, retarder, seat heater, soot filter, spoiler, tachograph, traction control, For sale is a used MAN TGS 18.430 4X2 LLS-U with the following specifications: First registration: 03/03/2020 Mileage: 198,186 km Engine output: 316 kW / 429 HP Displacement: 12,419 cc Number of gears: 14 (forward) / 2 (reverse) Gross vehicle weight: 18,600 kg Unladen weight: 7,401 kg Payload: 10,378 kg Number of axles: 2 Swap body and flatbed dimensions: 5.99m length x 2.50m width x 3.59m height TÜV (roadworthiness inspection): new Safety inspection (SP): new Condition: Used The vehicle’s condition, both visually and technically, is consistent with its year of manufacture. No significant defects known. Knjdeyhbqlspfx Aamjc The vehicle is sold as seen, with all warranties excluded.

Condition: used, Year of construction: 2004, Format: 0x0 Equipment: Semi-automatic and automatic foil packaging machines Kjdox N I Ubjpfx Aamjnc Minipack Sealbag sealing machine For packaging printed materials such as magazines, booklets, and other printed materials Easy to operate and adjus