Used Grease Separator for sale (7,362)

Condition: used, Year of construction: 2013, Overview This Cermex F38741, built in 2013, is an automatic cardboard case erector that forms shipping cases from flat blanks for an end-of-line packaging setup. Blanks are taken from the magazine, erected, the bottom flaps are folded and closed, and the open case is discharged on the outfeed rails to the downstream packer. The machine comes from a wine packaging operation and has been dismantled and stored. Technical data - Manufacturer: Cermex - Model: F38741 - Year of manufacture: 2013 - Machine type: automatic cardboard case erector - Output: up to 40 cases per minute - Power supply: 400 V, 50 Hz, 3P+N+PE, 23 A full load - Control: Siemens SIMATIC S7-200 PLC (CPU 224) Equipment - Blank magazine with infeed chain and lugs - Erecting station with pick-up head on a cable-chain carriage - Bottom flap folding and closing section - Outfeed rails for the erected cases Peds Afdr Nepfx Akiorc - Enclosure with transparent safety doors and signal tower - Separate control cabinet with Siemens operator panel, emergency stop and control transformer - CE marked Condition Dismantled and stored. An inspection is possible. Availability Available immediately. Location: France.

Condition: used, Year of construction: 2016, functionality: fully functional, BAC VXC S455 evaporative condenser, R134a Used 5 units Baltimore Aircoil International (BAC) VXC S455 evaporative condenser, built 2015, serial number H150832701. Made in Heist-op-den-Berg, Belgium. It is an evaporative condenser: hot refrigerant vapour enters the coils inside the unit, water is sprayed over the coil surface, and centrifugal fans draw air through the pack. The refrigerant condenses and returns to the refrigeration plant. No separate water-cooled condenser is required on the chiller. The unit has twin R134a heat-exchanger coils (circuits A and B) and a centrifugal fan section. It was installed on a rooftop as the heat-rejection side of a refrigeration / chilled-water plant. Manufacturer: Baltimore Aircoil International nv Model: VXC S455 Serial number: H150832701 Year of manufacture: 2015 Type: induced-draft evaporative condenser Vessel type code: PED C100 Refrigerant: R134a Coil volume: 932 L per coil (A and B) Design pressure: −1 / 23 bar Prodozz Sidopfx Akiec Test pressure: 34 bar Design temperature: −20 / +120 °C Fan overall efficiency (nameplate): 59.05% Marking: CE BAC catalogue figures for VXC S455 Base heat rejection: approx. 1,961 kW Operating weight: approx. 11,270 kg Shipping weight: approx. 8,125 kg Dimensions: approx. 5,385 × 2,397 × 4,248 mm Air flow: approx. 34.9 m³/s Fan motor: 1 × 30 kW Spray water: approx. 38.5 l/s, pump 1 × 4 kW Application Heat rejection for industrial chillers and refrigeration plants on R134a. A natural match for the Star Refrigeration package water chillers (contract 100663, 840 kg R134a charge): discharge gas goes to the BAC coils, liquid returns to the chiller. Condition and sale Used industrial equipment, removed / being removed from site. Price on request. Can be sold with the Star chillers or as a standalone condenser. Model, serial number and pressures are taken from the factory plates; actual capacity at the new site depends on condensing temperature and ambient wet bulb.

Condition: refurbished (used), Year of construction: 2025, machine/vehicle number: R-00707, load capacity: 45 kg, arm reach: 2,650 mm, controller manufacturer: R-30iB Plus A-size, teach pendant manufacturer: A05B-2255-C101#EGN, Never-Used FANUC M-710iC/45M manufactured in 2025.04. The robot comes with an R-30iB Plus A-size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: M-710iC/45M Model Number: A05B-1125-B208 Year of Manufacture Robot: 2025.04 Warranty term (months): 12   Payload (kg): 45 Reach (mm): 2650 Repeatability (mm): ± 0.06 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Wall, Angle Mount Weight (kg): 570   Controller: R-30iB Plus A-size Prsdpfs Afuy Rsx Akioc Year of Manufacture Cabinet: 2025.03 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 12

Condition: new, Technical data for the base plate: Shelving system: Bito Type: Pro Included in delivery: 01x Base plate, new Material color: Sendzimir galvanized Prodo Afg U Tepfx Akioc Type: L For frame profile: P1, P2, P3 Material thickness: 5 mm Overall width: 120 mm Overall depth: 105 mm Height: 30 mm Weight per piece: 0.44 kg / piece Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipping of this item will incur extra costs, which can be requested separately from us depending on the delivery location and scope of delivery.

Condition: ready for operation (used), Year of construction: 2023, controller manufacturer: TRUMPF, controller model: Touchpoint TruBend, overall weight: 30,000 kg, total width: 5,150 mm, total height: 2,995 mm, product length (max.): 6,500 mm, Folding machine manufactured in 2023. This TRUMPF TruBend Center 7030 (B34) features a maximum bending edge length of 3,123 mm and a holder clamping force of 101 t. It includes a 2-axis part manipulator with a travel of 2,653 mm and an automatic loading/unloading system. If you are looking to get high-quality bending capabilities, consider the TRUMPF TruBend Center 7030 (B34) machine we have for sale. Contact us for further details. Prjdpfx Ake Afpmljijc • Construction: Welded steel frame; Bending system: Wedge drive; Crowning: Included, adjustable via control • Capacities • Max bending edge length: 3,123 mm • Min bending edge length: 200 mm • Min bending width with standard holder: 145 mm • Min bending width with ENW tools: 40 mm • Max box height: 220 mm • Holder clamping force: 101 t • Material thickness: min 0.4 mm; max structural steel 3.0 mm; max stainless 2.2 mm; max aluminum 4.0 mm • Manipulation and positioning (integrated) • 2-axis part manipulator with 12 suction modules; X travel 2,653 mm; stroke 100 mm • 5-axis rear stop; Rotary manipulator; Front stop; Loading pincers • Automatic part positioning and rotation • Speeds • Y-axis rapid traverse: 250 mm/s • Front stop: 3,000 mm/s • Part manipulator: 3,000 mm/s • Rotary manipulator: up to 3 rev/s • ToolMaster Bend: 2,400 mm/s • Positioning accuracy • Y: 0.10 mm; X: 0.05 mm; R: 0.05 mm • CNC control • 21.5" touchscreen; Windows 7 Ultimate 64-bit; keyboard and mouse • USB; RJ45; Ethernet 10/100 Mbit/s; Internet teleservice/remote diagnostics • Programming software • TecZone Fold floating license • Automatic programming from 2D/3D, automatic bending program generation • 3D bending simulation; collision checking; manual program modification • ToolMaster Bend (automatic tool handling) • Automatic hold-down tool positioning and setup per program • Automatic positioning of standard, Pick&Place, and curved holders • Included tooling • 16 standard hold-down tools (160 mm each) • 6 Pick&Place hold-down tools; segments 10/15/20/40 mm • Corner hold-down tool, length 199 mm • OBW90 and UBW90 bending tools • ENW equipment • ENW function for tilting hold-down tools • ENW110-40 tool, length 3,123 mm, depth 40 mm • Min bending width with ENW: 40 mm • Bend angle measurement • Optical bend-angle assistance with integrated camera • Graphical comparison of programmed vs. actual angle • Minimum part-side length for angle measurement: 10 mm • Safety • CE certification; rotating safety doors; safety light barriers • Working-area access protection; foot switch with enable; emergency stop • Electrical power supply: 80 kVA Additional equipment • Automatic loading/unloading system with storage interface • Automatic blank separation and feeding; transfer to bending center • Automatic finished-part unloading with belt conveyor • Max blank size: 3,048 x 1,500 mm • Storage interface included • Loading trolley: not included • Rail set: not included • Additional part handling modules • 12 three-surface vacuum modules (upper/lower/front suction) • 6 magnetic modules and 4 two-surface magnetic modules • Vacuum and magnetic modules can be used together • Identification and connectivity accessories • Wireless 2D code reader with Bluetooth • Barcode and DataMatrix code reading • Automatic production program loading

Condition: new, Technical data for the base plate: Shelving system: Bito Type: Pro Included in the scope of delivery: 01x Base plate, new Material color: Sendzimir galvanized Type: M For frame profile: P4, P5, P6 Material thickness: 6 mm Overall width: 150 mm Overall depth: 105 mm Height: 32 mm Weight per piece: 0.66 kg / piece Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch Prjdpfxo Afn U Ij Akioc General information about the item: This item is offered for pickup only. Any additional transport or shipment of this item will incur additional costs, which can be requested separately from us depending on the delivery location and scope of delivery.

Condition: good (used), Dust extraction fan, extraction, dust blower, extraction system, dust blower, dust extraction device, separator, welding fume filter, welding fume extraction, flue gas extraction fan, filter system Cartridge dust extraction system Prodpfozukp Aex Akijc -Manufacturer: TEKA, filter system for extraction system including control unit with frequency converter -Type: ZPF9 -Cartridge filter: see photos -Inlet/Outlet: Ø640 mm / Ø640 mm -Extraction capacity: up to 20,000 m³/h -Note: A filter unit only, without a suction fan, can be supplied for an additional charge (ID38772) -Dimensions: 1840/1475/H2670 mm -Weight: 689 kg

Condition: used, functionality: fully functional, Year of construction: 2006, Upper heating and pasteurization tank Lower cooling and churning cylinder Maximum capacity per cycle: 10 L Batch size per cycle: 4 to 8 kg Indicative hourly production: 40 to 60 L/h 17 manufacturing programs Heating, cooking and pasteurization Cooling and churning of preparations Upper tank with transparent lid Lower cylinder with direct expansion Multiple refrigerant injection Executive electronic control LCD screen and digital displays Controls for the hot and cold sections Front extraction of preparations Stainless steel exterior cladding Water-cooled condenser Power supply: 400 V / 50 Hz / three-phase Rated electrical power: 10.10 kW Announced protection rating: IP22 Dimensions (L x D x H): 650 x 1200 x 1410 mm Weight: 330 kg Used BRAVO Trittico 610 Executive pasteurizer and ice cream churning machine – Multifunction production General presentation The used BRAVO Trittico 610 Executive is a professional combination unit that combines the functions of a pasteurizer and an ice cream churning machine in a single machine. Designed for artisanal ice cream makers, pastry chefs and chocolatiers, it allows for heating, pasteurizing, cooling and churning of various preparations. With a maximum capacity of 10 L per cycle and an indicative hourly production of 40 to 60 L, this equipment combines a thermal preparation tank and a cooling cylinder. Its Executive control system facilitates the management of operations and the adaptation of cycles to professional recipes. Why this model stands out The Trittico 610 Executive combines two manufacturing steps usually performed by separate equipment. The upper tank accommodates the ingredients for heating, mixing and pasteurization operations. The lower cylinder then ensures the cooling and churning of the preparations. This 2-in-1 configuration limits the handling between machines and facilitates the organization of production in an ice cream or pastry laboratory. The Executive electronic control has dedicated programs for the different preparations, with a central display and separate controls for the hot and cold sections. Key advantages Dual function: pasteurization and churning Upper tank dedicated to heating and cooking Lower cylinder for cooling and churning Capacity of 4 to 8 kg of mixture per cycle Maximum announced production of 10 L per cycle Indicative hourly production of 40 to 60 L Pedpfo Aa Axwox Akijrc Executive control with manufacturing programs Electronic display and control buttons Front extraction of preparations Stainless steel exterior construction Applications in ice cream making, pastry and chocolate making

Condition: refurbished (used), Year of construction: 2025, machine/vehicle number: R-00741, load capacity: 45 kg, arm reach: 2,650 mm, controller manufacturer: R-30iB Plus A-size, teach pendant manufacturer: A05B-2255-C101#EGN, Never-Used FANUC M-710iC/45M manufactured in 2025.09. The robot comes with an R-30iB Plus A-size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: M-710iC/45M Model Number: A05B-1125-B208 Year of Manufacture Robot: 2025.09 Warranty term (months): 12   Payload (kg): 45 Reach (mm): 2650 Repeatability (mm): ± 0.06 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Wall, Angle Mount Weight (kg): 570   Controller: R-30iB Plus A-size Year of Manufacture Cabinet: 2025.08 Predps Afzxyefx Akioc RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 12

Condition: used, Technical data for the pallet racking upright: Racking system: META (Thyssen) Type: Multipal N Included in the scope of delivery: 01x Pallet racking upright, used Material color: anthracite black (rusted) Profile dimensions: 100 x 65 x 2.5 mm Includes cross and diagonal braces and base plates The uprights are pre-assembled Pjdpfxe Af Icrj Akiorc (welded framework) Height: 3,400 - 3,300 mm Depth: 1,100 mm Notes: We offer this item exclusively for "private" use, as due to rust and minor damage, it is no longer suitable for commercial use. The item is offered for sale in its current condition, as is, no returns. One-time special price. Your contacts in our company: Mr. Andre Evering Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is only offered for collection. Any additional transport or shipping of this item will incur additional costs, which can be requested separately depending on the delivery location and scope of delivery.

Condition: refurbished (used), Year of construction: 2025, machine/vehicle number: R-00709, load capacity: 45 kg, arm reach: 2,650 mm, controller manufacturer: R-30iB Plus A-size, teach pendant manufacturer: A05B-2255-C101#EGN, Never-Used FANUC M-710iC/45M manufactured in 2025.04. The robot comes with an R-30iB Plus A-size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: M-710iC/45M Model Number: A05B-1125-B208 Year of Manufacture Robot: 2025.04 Warranty term (months): 12   Payload (kg): 45 Reach (mm): 2650 Repeatability (mm): ± 0.06 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Wall, Angle Mount Weight (kg): 570   Controller: R-30iB Plus A-size Year of Manufacture Cabinet: 2025.04 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Predpo Agbfvjfx Akijc Teach Pendant Cable Length (m): 12

Condition: used, Stanzkraft: 550 kN (e.g. punches holes 30 mm in 16 mm material), with locating device via foot pedal to anchoring Cuts 350 x 13 mm or 230 mm on the flat bar shear Overhang: 305 mm Two separate foot switches for the punching and shearing side, so that punching and shearing can be performed independently Support table on punching side Podpfx Aket Exprjisrc Assortment of tools is included in the price

Condition: excellent (used), FOR SALE – INDUSTRIAL HYDRAULIC PRESS, SACK & KIESSELBACH Psdpj Aggbusfx Akisrc Selling a SACK & KIESSELBACH hydraulic press, workshop identification number AE 7417. This is a robustly built machine, equipped with: • Work table with wedges and support pieces, as seen in the photos. • Control panel with analog gauges. • Separate hydraulic unit with a Siemens motor. • Protective housing around the work area.

Condition: used, Year of construction: 2007, travel -x axis 800 mm travel -y axis 500 mm travel -z axis 610 mm control HEIDENHAIN - TNC 530 table load 600 kg number of spindle speeds 14.000 U/min numbers of positions in the tool changer 46 tool taper HSK-A63 Milling Machine - Vertical | FEHLMANN - PICOMAX 95 equipped with 46-way tool changer and chip conveyor. Pedpfx Ao Aa A Rmokijrc Equipment / Scope of Delivery: - swivel rotary table (4th + 5th axis) - touch probe: HEXAGON - tool measurement system: Blum - oil mist separator: Donaldson - high-pressure coolant system with coolant pump: Fehlmann - burn Engineering FD 2500-F11 cooling unit - Knoll 300 K-1 scraper belt conveyor The machine is in a well-maintained condition. Please refer to the offer for further technical details. - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - #Tags: PICOMAX95 | PICOMAX-95

Condition: excellent (used), Year of construction: 2012, control type: CNC control, controller manufacturer: Mazatrol, laser power: 4,000 W, table length: 3,000 mm, table width: 1,500 mm, travel distance X-axis: 3,050 mm, travel distance Y-axis: 1,525 mm, travel distance Z-axis: 150 mm, feed rate X-axis: 30,000 m/min, feed rate Y-axis: 30,000 m/min, feed rate Z-axis: 30,000 m/min, overall weight: 12,700 kg, total length: 8,500 mm, total width: 4,500 mm, total height: 2,800 mm, Machinery manufacturing: Producing machine covers, brackets, panels and structural components. Automotive industry: Manufacturing brackets, components and prototype parts. Agricultural machinery: Producing parts for tractors, trailers and agricultural equipment. Construction and steel fabrication: Cutting connection plates, mounting brackets and structural parts. HVAC and ventilation: Manufacturing ventilation components, panels and ductwork. Automatic sheet loading and unloading system – Large overhead gantry with integrated sheet handling equipment, suitable for automated material transfer. Mazak CELL 510 VA automation system – Separate automation control cabinet, identified by its nameplate and operating panel. Automatic pallet changer / shuttle table – Two cutting pallets allow material preparation and unloading while the machine processes another sheet. Dust extraction equipment – Large extraction ducting and associated equipment visible, although the complete filtration installation cannot be verified. Safety enclosure – Perimeter safety fencing with access gates and emergency-stop controls around the automation system. Machinery manufacturing: Producing machine covers, brackets, panels and structural components. Automotive industry: Manufacturing brackets, components and prototype parts. Agricultural machinery: Producing parts for tractors, trailers and agricultural equipment. Construction and steel fabrication: Cutting connection plates, mounting brackets and structural parts. HVAC and ventilation: Manufacturing ventilation components, panels and ductwork. Electrical cabinet manufacturing: Cutting enclosures, control panels and mounting plates. Main technical specifications Working area: Approximately 3,050 × 1,525 mm Mild steel cutting capacity: Up to 25 mm Prjde Agfxnopfx Akiec Stainless steel cutting capacity: Approximately 12 mm Aluminium cutting capacity: Approximately 10 mm Working area X Axis: 3050mm Working area Y Axis: 1525mm Working area Z axis: 150mm Table Length: 3000mm Table Width: 1500mm Power resonator: 4000kW / Amp Feed rate X-Axis: 30000mm/min. Feed rate Y-Axis: 30000mm/min. Feed rate Z-Axis: 30000mm/min. Sheet master loading arm:yes Dust collector: yes Length: 8500mm Width: 4500mm Height: 2800mm Weight: 12700kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 2018, Used Machine Year of Manufacture: 2018 Special Feature: Machine with a gluing height of up to 100 mm! Condition: Factory-inspected by Lange Maschinenbau Features and Technical Specifications: - Machine table with 13 rollers for improved workpiece guidance - Edge feed, synchronized with the belt feed - Edge thickness adjustable via digital counter - Pneumatic roller separation with blade (for cutable edges) - Three pressure rollers - Belt feed: - 0.25 kW - Approx. 1,250 mm long - Approx. 6.0 m/min - 50 mm wide toothed belt with a thick, workpiece-protective rubber covering - Digital counter for height adjustment - Direct glue application to the workpiece: Leak-proof glue tank with glue supply from below and fast heat-up time after machine shutdown - Flush trimming unit: - for the front and rear edges of the workpiece - Automatic sensing of the workpiece - Pneumatic trimming with a blade for cut-ready edges - Flush milling unit - With vertical sensing and horizontal guidance - Reproducible adjustment via digital counters - 2 powerful 0.4 kW high-frequency motors - Continuously adjustable from 4,000 to 18,000 rpm - Milling cutter: 70 mm, Z4, radius 2 mm/15° - Central exhaust port: 100 mm - 2 chip extraction hoods with 60 mm hose - Automatic height adjustment of the upper router bit via the belt feed - Continuous workpiece support, approx. 1,800 mm long - Workpiece support rail, extendable by approx. 300 mm - Rotatable film plate: 800 mm - Workpiece width: min. approx. 80 mm - Workpiece thickness: 10–100 mm - Workpiece length: min. approx. 220 mm - Edge thickness: 0.4–2.0 mm - Roller cutting: max. 1.0 × 55 mm, 2 × 45 mm - Glue pot heating power: 2.7 kW - Heat-up time: approx. 10 minutes - Working height: approx. 880 mm Psdpfozk Nmrex Akierc - Electrical connection: 400 V, 50 Hz, 3-phase N - Total power consumption: 3.8 kW - Pneumatic connection: 6 bar Dimensions (without film tray): approx. 1800 x 700 x 1300 mm Weight: approx. 260 kg

Condition: used, Year of construction: 2007, functionality: fully functional, Window and door component production line Manufacturer: WEINIG, Type: UC-Matic Year of manufacture: 2007 Line consisting of: Pos. 1: Infeed Unirex 2000 Prodpfs Agvhpjx Akioc Transverse + longitudinal conveying system PHV R For the indirect feeding of both identical and different workpiece lengths. System consisting of a transverse conveyor and a roller conveyor - Transverse conveyor, 6 lanes - Loading area for manual filling. - Automatic buffer zone - Automatic part separation using a clamping and reversing device - Transfer to a roller conveyor - Roller conveyor, powered - Pneumatically height-adjustable Adjustment travel, max.: 25 mm Transport length: 2300 mm Roller width: 160 mm Roller diameter: 50 mm Roller spacing, graduated: 120-825 mm Transport speed, fixed: 20 m/min. Motor: 0.2 KW (0.3 HP) 380 V / 50 Hz Pos. 2: Conveyor belts Conveyor belt, powered (TB 250) With center guide Transport length: 1000 mm Belt width: 250 mm Working height, adjustable: 820-1050 mm Guide stop, right: 70 mm Belt speed, fixed: approx. 20 m/min. Motor: 0.2 KW (0.3 HP) 380 V / 50 Hz Pos. 3: Machining center Weinig Unirex 2000 Pos. 4: Transport between machines with double part formation Longitudinal + transverse conveying system LKF 1 For the transport and stacking of both identical and different workpiece lengths at the end of the line. Workpiece reference line: roller conveyor – infeed side System consisting of a roller conveyor and a transverse conveyor - Roller conveyor, powered - Transport length: 2300 mm - Transverse conveyor, 7 lanes, height-adjustable Turning device WVU in the transverse conveyor, including options For changing the end face of workpieces. Rotational movement motorized 180° around the vertical axis. Pneumatic height adjustment of the turning device up to the max. wood height (100 mm) 4 x Additional automatic buffer zone (max. 8 zones) Pos. 5: Conveyor belts Conveyor belt, powered (TB 250) Without center guide and glass strip guide plate Pos. 6: Transverse machining Weinig Unitec 15 1. Tenon and groove spindle 2. Tenon and groove spindle Pos. 7: Conveyor belts Conveyor belt, powered (TB 250) Without center guide and glass strip guide plate Transport length: 1000 mm Belt width: 250 mm Working height, adjustable: 820-1050 mm Guide stop, right: 70 mm Belt speed, fixed: approx. 20 m/min. Motor: 0.2 KW (0.3 HP) 380 V / 50 Hz Pos. 8: Longitudinal machining Weinig Univar 12 1. Profiling spindle 2. Profiling spindle Profiling cutter head, horizontal, top 3. Profiling spindle Profiling cutter head, vertical, right Profiling cutter head, vertical, top (in the auxiliary stand) Profiling cutter head, horizontal, bottom (in the auxiliary stand) Pos. 9: Turning system with clamping device Pos. 10: Outfeed of the line Longitudinal + transverse conveying system LKF 1 For the transport and stacking of both identical and different workpiece lengths at the end of the line. Workpiece reference line: roller conveyor - infeed side System consisting of a roller conveyor and a transverse conveyor - Roller conveyor, powered - Transport length: 2300 mm - Roller width: 230 mm - Roller diameter: 50 mm - Roller spacing, graduated: 120 - 825 mm - Transport speed, fixed: 20 m/min. - Motor: 0.2 KW (0.3 HP) 380 V / 50 Hz - Stop height: 30 mm - Transverse conveyor, 7 lanes, height-adjustable - Adjustment travel: 25 mm - Conveying and stacking length: 3000 mm - Support width: 2000 mm - Working height, adjustable: 820-1050 mm - Conveying speed, fixed: 10 m/min. - Moto

Condition: good (used), Technical data for the pallet racking beam: Racking system: Stow Type: Pal Rack NS Included in the scope of delivery: 01x Pallet racking beam, used Material color: RAL 2004 orange Box profile: 100 x 50 mm Beam type: PNB 0480 Agraffe: 4 HK (hooks) Clear width: approx. 2,700 mm Max. load per beam pair: 1,500 kg with evenly distributed load 02x Locking pins, used Design: fully galvanized For securing the longitudinal supports against unintentional lifting out Your contact persons in our company: Mr. Andre Evering Pedps Agvu Aofx Akierc Mr. Mario Klöver Mr. Falk Deutsch General information about the item: This item is offered for collection only. Any additional transport or shipping of this item will incur extra costs, which can be requested separately depending on the delivery location and scope of delivery.

Condition: excellent (used), Year of construction: 2026, operating hours: 3 h, functionality: fully functional, machine/vehicle number: DS-62-607, total length: 1,760 mm, total width: 1,610 mm, total height: 2,085 mm, overall weight: 1,120 kg, input voltage: 400 V, workpiece height (max.): 150 mm, input frequency: 50 Hz, workpiece width (max.): 600 mm, table height: 900 mm, input current: 14 A, This Q-Fin DS600 comes from our showroom in Bergeijk and is now available for sale. The machine has only been used for demonstrations and is therefore in excellent condition. The DS600 is fully operational and can be inspected and tested by appointment in our showroom. The DS600 is a powerful stand-alone slag hammer for the quick and efficient removal of metal slag from thermally cut sheet metal up to 600 mm wide. The machine is specially designed to effectively remove slag formation after the cutting process, making it an ideal first step in the finishing process. By removing metal slag in advance, it is prevented from causing damage to subsequent machines during further processing. In addition, the DS600 reduces contamination within the production process and positively influences the lifespan of abrasives and other consumables. The DS600 offers an efficient alternative to the manual removal of metal slag. This significantly reduces the physical strain on operators and allows products to be processed faster and with a more consistent quality. Thanks to its stand-alone design, the DS600 can be easily used as a separate machining unit or as a preparation for a subsequent finishing process. Prjdpfx Ako Agm Rvsioc The Q-Fin DS600 combines speed, ease of use, and effective slag removal in one compact solution. This makes the machine particularly suitable for sheet metal processing companies that want to optimize their production process and reduce manual operations. This machine is immediately available from our showroom in Bergeijk. Please feel free to contact us for more information or to schedule a demonstration.

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2012, Submitting a bid obligates the bidder to collect the item by December 1, 2026. No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS General Information Prsdpfxj Aayn Ns Akisc Manufacturer: TRUMPF Model: TruLaser 7040 (L62) Year of Manufacture: 2012 Operating Hours: need to be updated Working Area Working area X/Y/Z: 4,000 × 2,500 × 115 mm Speed: max. 304 m/min Accuracy: ±0.1 mm Laser Laser power: 2 × 4 kW Laser heads: 2 units Condition of laser heads: functional Cutting Capacities Sheet metal thickness steel: max. 20 mm Sheet metal thickness stainless steel: max. 15 mm Sheet metal thickness aluminum: max. 10 mm Control System Control system: Siemens Sinumerik 840 D SL Machine Dimensions and Weight Length: 15,800 mm Width: 7,280 mm Height: 3,090 mm Weight: 16,500 kg Environmental Conditions Ambient temperature: max. 43 °C EQUIPMENT Thin sheet metal productivity package for high-speed, standard, and compressed air cutting 2 lens cutting heads with 130 mm focal length Compressed air cutting BrightLine CoolLine with 2 separate lens cutting heads 4 clamping jaws, 2 per pallet Wide transverse conveyor belt “Wavebelt” with tilting container Tilting container to the left of the machine More powerful compact dust extractor Connection piece for the exhaust duct of the compact dust extractor MDE interface

Year of construction: 1994, condition: ready for operation (used), travel distance X-axis: 2,000 mm, travel distance Y-axis: 800 mm, travel distance Z-axis: 1,000 mm, controller manufacturer: HEIDENHAIN, controller model: TNC 407, number of axes: 3, This MIKRON BTM 2000 surface grinding machine was manufactured in 1994. It features an impressive X-axis travel of 2,000 mm, Y-axis travel of 800 mm, and Z-axis travel of 1,000 mm. The machine has a maximum table load of 3,500 kg and a spindle speed of up to 4,000 rpm. If you are looking to get high-quality surface grinding capabilities, consider the MIKRON BTM 2000 machine we have for sale. Contact us for further details. Prsdpfs Agvq Hsx Akisc - Not fully functional; error message "Grober Positionierfehler" (Gross positioning error);- Electronic Handwheel: Heidenhain HR 330 - Maximum Table Load: 3,500 kg - Rapid Traverse (X/Y/Z): 15 m/min each - Milling Head: Manual universal milling head - Spindle Speed: Up to 4,000 rpm (min⁻¹) - Tool Taper / Holder: ISO 40 according to DIN 2080 - Linear Measuring System: Direct Heidenhain LS 106 C linear scales in X, Y, and Z - Drive Technology: Siemens SIMODRIVE 611 - Working Area Enclosure: Sliding doors and strip curtain / lamellar splash guard - Cooling / Auxiliary: Separate cooling unit / aggregate - Maintenance History: Y/Z-slides overhauled by a specialized company approx. six years ago

Condition: refurbished (used), Year of construction: 2013, machine/vehicle number: R-00735, load capacity: 20 kg, arm reach: 1,811 mm, controller manufacturer: R-30iA B-Size, teach pendant manufacturer: A05B-2255-C101#EGN, Refurbished FANUC M-20iA manufactured in 2013.05. The robot comes with an R-30iA B-Size controller including iPendant.   Our experts extensively tested the robot, after which we conducted a maintenance service according to the manufacturers’ specifications. The grease is examined for the amount of iron particles, indicating the corresponding axes' condition. Only robots in excellent mechanical condition will be completely refurbished, ensuring a long-term solution for our customers. This enables us to deliver our robots with a warranty term of 12 months as standard!   Brand: FANUC Model: M-20iA Model Number: A05B-1222-B202 Year of Manufacture Robot: 2013.05 Warranty term (months): 12   Payload (kg): 20 Reach (mm): 1811 Repeatability (mm): ± 0.08 Controlled Axes: 6-axis Installation Type: Floor, Upside-down, Wall, Angle Mount Prodpfx Akj Agnwteiec Weight (kg): 250   Controller: R-30iA B-Size Year of Manufacture Cabinet: 2013.05 RCC Length (m): 7   Teach Pendant: A05B-2255-C101#EGN Teach Pendant Cable Length (m): 10  

Condition: used, Year of construction: 2025, input voltage: 380 V, total length: 1,650 mm, total width: 1,800 mm, total height: 1,750 mm, tank capacity: 390 l, empty load weight: 1,650 kg, power: 11 kW (14.96 HP), SPRB-SPRS Series 400 V three-phase power supply Frequency 50-60 Hz Current 24.8 A Total power 11.4 kW Dough capacity 250 kg Flour capacity 166 kg Bowl volume 390 L 2-speed spiral Spiral motor 6.5 / 11 kW Bowl motor 1.1 kW Automatic speed change Bowl rotation by pulses Bowl rotation direction reversal Hydraulic tilting Discharge into hopper or divider Stainless steel bowl Dimensions L × W × H 1800 × 1650 × 1750 mm Loading height 1040 mm Unloading height 1930 mm Maximum height in tilting position 3100 mm Weight 1650 kg Year 2022 Used self-tilting dough mixer 160, capable of handling 250 kg of flour, SPRS250 General description The MECNOSUD SPRS250 is a large-capacity, self-tilting spiral dough mixer designed for bakeries, pastry shops, and production units that need to prepare up to 250 kg of dough per cycle. Its fixed 390-liter bowl can hold up to 166 kg of flour. This SPRS version is equipped with a hydraulic tilting mechanism that allows the dough to be discharged at height directly into the hopper of a divider or other production equipment. A mixer designed for large-scale production The SPRS250 combines a two-speed spiral, an independently motorized bowl, and two electronic timers. The operator can thus program the two phases of kneading separately, with an automatic transition from the first to the second speed. This arrangement facilitates the repeatability of recipes and limits interventions during the cycle. Key advantages Maximum dough capacity of 250 kg Up to 166 kg of flour Fixed 390-liter stainless steel bowl Two spiral speeds Two independent electronic timers Automatic transition between the two speeds Two independent motors for the bowl and the spiral Bowl rotation direction reversal Bowl rotation by pulses Hydraulic tilting, reducing manual handling Direct discharge into a hopper or divider Robust construction suitable for sustained production Detailed technical specifications Brand MECNOSUD Manufacturer's model SPRS250 Type of mixer Automatic spiral mixer with fixed bowl Discharge system Hydraulic tilting at height Maximum dough capacity 250 kg Maximum flour capacity 166 kg Bowl volume 390 L Spiral speeds 2 speeds Spiral motor power 6.5 / 11 kW Bowl motor power 1.1 kW according to the manufacturer Motorization Two independent motors Cycle management Two electronic timers Bowl rotation Continuous, by pulses and reversible Transmission V-belts Bowl High-strength stainless steel Spiral High-strength stainless steel Central column Stainless steel Protective grill Stainless steel Unladen weight Approximately 1,650 kg Dimensions at rest Approximately 1800 x 1650 x 1750 mm Loading height 1040 mm Pedszqd Iqjpfx Akierc Unloading height 1930 mm Maximum height in tilting position 3100 mm Tilting footprint Approximately 2100 mm Data announced for this used unit Year 2022 Power supply 400 V three-phase Frequency 50-60 Hz Current 24.8 A Total power 11.4 kW Bowl capacity 84 L Discharge direction To the right Type of controls Electromechanical

Condition: used, 8m OFFICE CONTAINER for sale ✅ DETAILS & HIGHLIGHTS: We offer a 27FT office container (8 m length) in good condition – perfect as an office container, site office, or storage container. ✅ The container comes from the equipment of the French company CARGLASS and is of high quality. All technical components are intact and ready for immediate use. ✅ EQUIPMENT: Separate toilet with washbasin Office area with plenty of natural light Kitchenette with sink and hot water boiler Storage space Heating and air conditioning unit Heavy-duty power connection, electrical installation, and exterior lighting Prjdps Agwuajfx Akijc Ramp and fire extinguisher ✅ SPECIAL FEATURES: Practical room layout: office – toilet – storage Original photos – condition as shown Ideal as a construction site office, container office, or mobile service point Technically sound, ready for immediate use ✅ AVAILABILITY: from Dunkirk, France ✅ TRANSPORT: Free and non-binding offer for delivery (including unloading, if desired) – simply provide the postal code ✅ VARIETY: In addition to office containers, we also offer sea containers in all common sizes (20DV, 40DV, 20HC, 40HC…) for storage, construction projects, logistics solutions, or sea transport. We look forward to hearing from you! NAUTEXA GmbH

Condition: used, The Braibanti/Pavan extruder is designed for the continuous production of short-cut pasta, breakfast cereals, and pet food. The prepared dough is conveyed through a temperature- and moisture-controlled screw extruder toward the die, which ultimately defines the shape of the product. Extrusion takes place under controlled pressure and temperature to ensure consistency and structural integrity. At the end of the extruder, a motorized, speed-controlled rotating knife cuts the extruded product to the desired length. Psdpfo Agvygjx Akisrc Prior to extrusion, the dough undergoes a structured preparation process. It begins with a two-step mixing system that combines dry and wet ingredients into a homogeneous mass. This system uses a single mixing arm with directionally adjustable paddles to ensure proper pre-conditioning and hydration. The final stage of preparation takes place in a high-performance mixer/kneader unit, which further develops the dough structure to achieve optimal plasticity, consistency, and elasticity-critical parameters for stable and high-quality extrusion performance. Continuous mixer - preconditioner PR220 (2-line version) ± 100 L / screw Single mixing shaft with adjustable paddles, dual execution Motor 2 x 18,5 Kw - 978 rpm Liquid and dry ingredient supply Inspection and cleaning hatch Mixer VM210 ± 150L Single mixing shaft execution with adjustable paddles Motor 1.5 KW - 1461/64 rpm Extruder BR220 Dual execution, 2 extrusion heads Motor 2 x 37Kw - 1482 rpm Gearbox Sumitomo Cyclo Double-walled extruder housing, suitable for cooling Production capacity (Pet food) calculated at 30-40 kg/min (depending on the product) Operating pressure ± 30-40 bar depending on the die Powered cutting head/chopping knife (motor 1.1 Kw -920 rpm) Dimensions (L x W x H): 5.000 x 2.200 x 2.400 mm Possibility to run 2 separate products, 2 extrusion lines on 1 frame. without electric cabinet and controls