Used Double Column for sale (15,406)

Condition: used, Machine not operational – control system not running Special price Double-column hydraulic press ALPHA TEC -- ALPHATEC Type RPS 5000 Serial No. 300487 Year of manufacture: 2006 Pressing force: 500 tons Column gap front and rear: 2520 mm Table surface: 2500 x 2500 mm Ram surface: 2500 x 2500 mm Ram stroke: 600 mm Installation height max.: 600 mm Table height above floor: approx. 900 mm Tank capacity: approx. 1000 liters Ram retraction force: approx. 22 tons Chedpfx Abedzqptjbef Adjustable approach speed: 100-800 mm/s Pressurization to 5000 kN: approx. 0.7 sec. Return speed: approx. 300 mm/s Main motor power: 75 kW Control pump motor power: 2.2 kW Power supply: 400 Volt, 50 Hz - 8-position flat guide for the ram - Hydraulic ram locking at TDC - Freestanding control cabinet (200 x 50 cm) - Siemens PLC control S7-314 - Operation via Siemens OP 170-B (5.7”) - Two-hand control desk, freestanding - Floor-level installation - Table plate 2510 x 2530 x 135 mm (approx. 6700 kg) - Central lubrication - Operating manual with circuit diagrams Required space (L x W x H): 372 x 260 x 460 cm Required space for horizontal transport (L x W x H): 460 x 372 x 260 cm Weight: approx. 50 tons The machine was used for straightening heated steel flanges. From insolvency – in good condition.

Condition: used, Year of construction: 2000, faceplate diameter 3200 mm swing diameter 3500 mm turning height 2200 mm Cjdpfx Abouddcgsbjhf range L-W-H 7730 x 6240 x 6700 mm control Typ 840 D sl voltage 3 x 400 V frequency 50 Hz turning speeds 0,8 - 40 U/min max. turning diameter 3500 mm total power requirement 51 kW weight of the machine ca. 86 t Technical specifications Machine type: CNC vertical lathe Manufacturer: Rafamet Year of manufacture: 1973 conventional General overhaul with control retrofit 2010 Control upgrade 2016 Control: Siemens 840 D Sl Condition: very good faceplate Turning diameter of the faceplate 3,200 mm Number of rotation stages of the face plate 3 (infinitely variable) Speed ??ranges of the faceplate 0.8 - 40 rpm Level I 0.8 – 3 rpm Level II 0.8 - 11 rpm Level III 0.8 – 40 rpm processing of workpieces Max. turning diameter 3,500 mm Max. turning height of the workpieces above the faceplate 2,200 mm vertical supports Smallest axis distance between the vertical supports 470 mm Largest ram travel of the left vertical support 985 mm Largest ram travel of the right vertical support 985 mm Axis Feeds - Infinitely variable feed Max.: X1.2 3m/min max.: z1.2 2.5 m/min Plunger cannot be pivoted Support — crossbar Rapid feed of the cross beam 600 mm/min Larger distance of the cross beam to the faceplate 2,300 mm load sizes +Permissible turning force when turning workpieces with a turning diameter of 2,000 mm and a turning speed of 20 m/min. 8,000kg +Largest chip cross-section for workpieces made of steel Fz = 50 kg/mm² at a turning speed of 20 m/min for all supports 45 mm² +Largest chip cross-section for workpieces made of steel Fz = 50 kg/mm² at a rotation speed of 20 m/min for a vertical support with max. plunger length 985 mm 2.5 mm² +Largest chip cross-section for cast iron workpieces HB = 160 kg/mm² at a turning speed of 20 m/min for all supports 120 mm² +Largest chip cross-section for cast iron workpieces HB = 160 kg/mm² at a rotation speed of 20 m/min for a vertical support with max. plunger length 985 mm 22.5 mm² +Largest permitted workpiece weight at 0.8 - 3.15 rpm 17,500 kg +Largest permitted workpiece weight at 4 - 40 rpm 7,500 kg electric motors Main drive motor power and revolutions 51 kW Power of the feed motors of: - Vertical support beam (2 pieces) 16 Nm (gear 1:10) - Tappet (2 pieces) 16 Nm (gear 1:12) Power and revolutions of the drive motor of the hydraulic pumps (2 pieces) 3kW - 1,500 rpm Power and revolutions of the clamp hydraulic motor of the vertical support beam 1.5 kW - 1,500 rpm Power and rotation for crossbar adjustment 15 kW - 1500 rpm 3.5 Information on the compressed air supply and other consumables Compressed air connection: 6 bar free of oil and water 3.6 Energy Consumption Conditions Voltage: 3 x 400V Control Voltage: 24V Frequency: 50Hz Fusing: 315 A Main dimensions and weight of the machine Length 7,730mm Width 6,240mm Height: 6,700mm Weight: 85,750 kg Tool: Capto 60 recording Not powered front panel Turning diameter of the front plate 3,200 mm Clamping disc diameter 3,400 mm Number of rotation levels of the front panel 3 (continuously adjustable) Front panel speed ranges 0.8 - 40 rpm Level I 0.8 - 3 rpm Level II 0.8 - 11 rpm Level III 0.8 - 40 rpm processing of workpieces Max. turning diameter 3,500 mm Max. turning height of the workpieces above ...

Condition: used, Year of construction: 2018, Are you in search of a bridge type milling machine? With X-travels ranging from 2-15m, Y-travels up to 4m, and Z-travels up to 2m, we offer a versatile selection of machines to meet various machining requirements. Whether it's CNC universal heads, W-axis, rotary table, tool changer, or controls from renowned manufacturers such as Siemens, Fanuc, and Heidenhain, our extensive range of accessories allows for maximum flexibility and efficiency. Take a look at the PDF catalog below! Discover the ultimate precision and robustness of our refurbished CORREA portal milling machines, meticulously restored by our experts in Spain. These machines have been meticulously inspected and tested according to the highest standards, guaranteeing top-notch machining quality. An outstanding example is our used CNC portal milling machine VM 2018, equipped with the proven Heidenhain control. With impressive performance data and detailed technical features, this machine has everything you need for precise and efficient machining. x-travel: 2300 mm y-travel: 2000 mm z-travel: 1000 mm Table size: 2300 x 1600 mm T-slots (width x spacing x number): 8x 22 x 180 mm Codpfshx R Dksx Abbohf max. table load: 8 t Distance between columns: 1840 mm Distance between spindle nose and table: 180~1180 mm Spindle motor: 22/46 kW Spindle torque: 140.1/286.5 Nm (S6-25%) Spindle nose: 50 SK Spindle speed: 10000 (direct) rpm Rapid traverse X, Y: 20000 mm/min. Rapid traverse Z-axis: 15000 mm/min Milling feed range: 1~10000 mm/min Machine size (LxWxH): 7027 x 5217 x 4339 mm Total power requirement: 60 kVA Machine weight approx.: 25 t CNC control: Heidenhain TNC 620 Chip conveyor with chip container: 2 pcs spiral, 1 pc hinge belt Through-spindle coolant: 20 bar CE version: Certified by TUV Used CNC portal milling machine with HEIDENHAIN 620 TNC control and extensive accessories, featuring: - Monoblock cast iron machine bed and monoblock crossbeam provide highest rigidity for precise machining results. - The entire structure has been optimized for rigidity and precision through FEM analysis. - P-class feed roller linear guides allow maximum load capacity with a lower friction coefficient (0.003-0.006). They ensure smooth operation through optimized roller circulation and guidance, reducing energy consumption. - The double-nut C3 ball screws ensure precise milling even for heavy loads. - Spindle direct drive with 10,000 rpm and SK50 tool holder. - Spindle motor power 22/46 kW (S6-25%). (22 kW continuous power, 46 kW for 30 minutes overload) - Spindle torque corresponds to 140.1/286.5 (S6-25%) Nm - Two spiral conveyors and one chain chip conveyor effectively remove chips. All essential components are sourced from reputable manufacturers in Europe, ensuring reliable, short-term, and long-term availability of spare parts. Don't miss the opportunity to optimize your production processes and invest in high-quality milling technology. Experience the difference that our portal milling machines offer - reliable, durable, and ready to tackle your most demanding tasks. Contact us today and let our experts guide you.

Condition: used, pressure 200 t distance between columns 1600 mm max. ram stroke 600 mm dayligth 900 mm table width 1600 mm table depth 1300 mm table height 1060 mm Chsdpfx Abeg S R Twsbsf ram surface 1600 x 1300 mm T-slots Din 650 / 22H12 rapid traverse 400 mm/s return speed 325 mm/s pressing speed 42 mm/s bei 40% mm/sec pressing speed 20 mm/s bei 100% mm/sec die-cushion pressure 800 kN die cushion stroke 150 mm speed of die cushion auf 68/ ab 225 mm/s

Condition: new, pressure 500 t column daylight 600 mm stroke 600 mm table surface area 3500 x1500 mm 600 mm feed down 8 mm/sec feed up 16 mm/sec travel on the bed 2200 x 900 mm total power requirement 30 kW weight of the machine ca. 28 t 2. STANDARD EQUIPMENT FRAME - Welded steel frame - Frame and plates are precision-milled using a CNC milling machine Chodpfx Ajfv Awhsbbjf - Chrome-plated cylinder - Worktop with threaded holes HYDRAULICS - Bosch Rexroth hydraulic pump - Hydrapack or Badestons hydraulic directional control valve - Hydraulic block in accordance with EN standards - 1000-liter hydraulic oil tank - Pressure adjustment via pressure transmitter/regulator ELECTRICS - Control cabinet in accordance with EN standards - All cables are labeled and clearly arranged - All electrical components are from Siemens CONTROL PANEL - Stroke control in any position - X, Y, and Z-axis movement via remote control - Stroke adjustment via sensor SAFETY - The machine complies with the EC safety standards 2006/42/EC Machinery Directive, EN ISO 16092-01 and 16092-03 - Two-hand operation - Emergency stop button - Safety rope with switch around the press 4. TRANSPORT AND INSTALLATION – The price includes transport costs, installation, and training at the customer's factory. – Hydraulic oil is not included in the price. – All handling costs (e.g., crane, forklift, etc.) are borne by the buyer. 5. WARRANTY – The machine has a 2-year manufacturer's warranty. – This warranty covers the delivery of all spare parts required for repair and service of the machine. Damaged parts will be returned to the manufacturer after replacement with a new part. – This warranty does not cover parts damaged due to improper use.

Condition: excellent (used), Year of construction: 1995, x-travel 14000 mm y-travel 5000 mm z-travel 1500 mm w-axis 3000 mm column daylight 4000 mm column: max. dist. table - spindle nose 4500 mm workpiece weight 100 t table dimension - longitudinal 9000 mm table dimension - cross 3000 mm spindle taper ISO SK 50 spindle turning speed range 2-2500 U/min spindle motor 113 kW spindle diameter 200 mm max. torque on the spindle 9500 Nm feed in x - axis 1-10000 mm/min feed in y - axis 1-10000 mm/min feed range Z-direction 1-10000 mm/min rapid traverse 20000 mm/min height over floor 8600 mm control SIEMENS 840C weight of the machine ca. 360 t ATTACHMENTS angular milling head yes autom. tool clamping yes Chjdpfovwgm Hex Abbsf ball spindles yes guideway covers yes coolant unit yes high pressure cooling syst. (through spindle) yes closed cabin yes chip conveyor yes TECHNICAL DESCRIPTION 2 portal milling centres, each with 3 table pallets 9000 x 3000 mm: - Tool changer with 420 tools - Head pick-up system - Video monitoring via camera - High pressure lubrication unit for inner cooling 70bar AVAILABLE HEAD UNITS: - Fixed angle head HS800C600 105 Kw 600 long - Fixed angle head HSD350C850 50 Kw 850 long - Fixed angle head HSD 40C880 12 Kw 880 long - Fixed angle head HSD 190C1000 30 Kw 1000 long - Vertical spindle unit VS800C 105 Kw 900 long - Universal spindle unit USIO40C 20 Kw B-axis rotatable at 1° at a time - Angle spindle unit SO800C905 - 22,5° fix - Angle spindle unit HSE1200CS -25° fix - Universal spindle unit (fork milling) USP475C 75 Kw 1/2° Hirth --> 1.350 1/min , B-Achse 0,5 Grad Hirth One additional drilling extension SE 350C plus 1 SE500C. DESCRIPTION OF CONDITION In 2011/2012 these 2 identical machines were retrofitted The milling length was extended to 14meters and an automatic changing system for table pallets was installed. Both machines can be seen under power by prior appointment.

Condition: used, Double-column hydraulic press SCHÖN Type SH 25 Machine no.: 4453 Year of manufacture: 1999 Pressing force: 25 tons Column width: 500 mm Lateral column clearance: 120 mm Table surface: 440 x 320 mm Table opening: Ø 175 mm Ram surface: 360 x 220 mm Clamping pin bore: Ø 40 mm Max. ram stroke: 100 mm Max. installation height: 270 mm Table height above floor: 900 mm Motor power: 7.5 kW Connection voltage: 380 V, 50 Hz Equipment: - Safety light curtain SICK, type FGS 300-11 - Two-hand operation - Stroke counter - Rapid and working stroke - Stroke limitation dependent on pressure or position - Mechanically adjustable fixed stop - Pressing force regulation - Adjustable pressing time 1–10 s (pressure holding time) - Adjustable return stroke speed - Blow-off device electrically pre-wired, without air valve Codpfxew A Amro Abbshf - Manual hydraulic tool safety, adjustable via handwheel Dimensions (L x W x H): 1300 x 1200 x 2200 mm Weight: approx. 1200 kg Good condition

Condition: used, Year of construction: 1998, x-travel 6000 mm y-travel 4000 mm z-travel 1250 mm w-axis 1500 mm Control Fidia max. workpiece weight 60000 kg Control unit for tool magazine/tool changer Siemens turning speeds 6,3 - 4000 U/min surface area 2500 x 4500 mm 48 St. tool taper SK50 Chsdpfx Asu I E Emebbef daylight between the side columns 3700 mm rapid traverse 30000 m/min total power requirement 63 kW weight of the machine ca. 150 t required space 16,8 x 10,3 x 7,9 m

Condition: new, neu ca. 4 Monate ab Auftragse Italien 104000 € 1965.6 € 125 to 500 mm 1200x700 mm 600 mm 115 mm/s 7 mm/s 70 mm/s Chjdpfxjwiqxpe Abbof 15 kW 2550 mm 1500 mm 2600 mm 4-pillar guide table and ram with T-slots 2 hand operation stroke adjustment pressure adjustment

Year of construction: 1978, condition: used, pressure 2000 /1000* t distance between columns 2650 mm stroke 500 mm column travel -side 500 x 1000 mm diameter of piston 710 mm number of pistons 2 distance between table / ram 1000 mm operating pressure 130 / 230 bar dayligth 800 mm table length 2500 mm table width 1600 mm table height 250 mm draw back pressure 500 kN number of T-slots 8 turning speeds 1500 U/min rapid speed 120 - 140 mm/min closing speed max. 120 - 140 mm/sec. return of plunger by small single cylinders 100 - 110 mm/sec hydraulical ram locking cutting sound absorber 300 t die cushion capacity 200 t die cushion stroke 250 mm speed of die cushion 100 mm/sec frequency 50 Hz voltage 380 V quantity of oil 2000 l total power requirement 93 kW weight of the machine ca. 100 t dimensions of the machine ca. 5000 x 2500 x 7200 mm transport measurements ca. 6500 x 3750 x 2190 mm 1991 assembly of a die cushion, pressure reduction to 1000 tons Chodpfxjd Ih Nco Abbsf reason: tools were only constructed to 1000 tons press has run in a perfect condition until disassembly. It was replaced by a press line. important for UVV: press has a hydraulic ram locking!

Condition: new, pressure 300 t working feed 3-8 mm/sec stroke 500 mm return speed 15 mm/sec table-size 3000 x 1500 mm tank capacity 45 l Chsdpjvxw Hmefx Abbof travel x / y 2600 x 1000 mm daylight 500 mm total power requirement 18,5 kW weight of the machine ca. 18 t

Condition: good (used), Year of construction: 2005, x-travel 6000 mm y-travel 3500 mm z-travel 1500 mm control SIEMENS 840D table load 12 t height over floor 6300 mm table dimension - longitudinal 5000 mm table dimension - cross 2500 mm no. of tables 2 tool change unit 200 -fach weight of tools max. 30 kg tool taper HSK A 100 diameter of tools max. 250 mm workpiece length 500 mm spindle turning speed range 5-6000 U/min c-axis -10 bis 370 ° b-axis 5 bis -95 ° column daylight 3000 mm distance spindle nose and table 1500 mm weight of the machine ca. 161 t dimensions of the machine ca. 20.5 x 11 x 6.3 m This WALDRICH-COBURG Valutec portal milling machine is in very, very good condition and can be Chsdpfxjvwglve Abbef beautiful condition and can be inspected by arrangement with the seller.

Condition: new, Year of construction: 2019, pressure:275 t distance between columns:3000 mm total power requirement:30 kW weight of the machine ca.:40 t draw back pressure:27 t pump capacity:Axialpumpe mit Proportionalventil :6000 mm :max. 3000 mm Table dimensions:6000 x 3000 mm table height over floor:700 mm distance between table / ram:1100 mm :450 l traversing speed:auf X und Y, 30-33 mm/sec. down speed:2-10 mm/sec Chjdpfxefxyige Abbof :2-50 mm/sec. Cylinder hub:900 mm Cylinder diameter:440 mm Stestle extension:200 / 200 mm / Ø :40 mm Siemens Control System:S7 1200 Monitor Siemens 9":Touch Panel Tax desk:tragbar

Condition: used, pressure / t distance between columns / mm stroke / mm This ram was dismantled from the MAE HY S 315s press Data from the machine to which Ram belonged: Press pressure devi. 315,000kg pressure up Ram stroke 800 mm Projection / table depth 720 mm Installation height 800 mm Table width 1200 mm Table height 1200 mm Total height / width / depth 4200 mm / 2200 mm / 4350 mm Weight 30 tons Machine body as seen on the low loader is 4 tons Csdsn Uzbrspfx Abbshf It's just the pestle!!!

Condition: good (used), Year of construction: 2023, functionality: fully functional, die cushion stroke: 200 mm, table width: 1,000 mm, table length: 1,200 mm, pressing force: 250 t, Ejector in ram - approx. 10 t Table drawing cushion approx. 800 x 850 mm Weight approx. 18 tons Stroke approx. 600 mm Csdpfsvga H Eex Abbehf

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment Codpfx Asgpxc Sobbjhf - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: new, Year of construction: 2024, functionality: fully functional, installation height: 400 mm, table width: 1,000 mm, table length: 830 mm, pressing force: 135 t, EXNER New Double column press - Eccentric press DEXRH 135/1000/1 Year of construction 2024 Nominal pressure capacity 1,350 kN Dimensions Clamping plate width depth 1,000 x 830 mm mm T-slot clamping plate 22 mm Column width 1,050 mm Ram size Width Depth 1,020 x 740 mm T-slot ram 22 mm Cjdpfxeup Sqkj Abbehf Centering groove ram width 30 mm depth 15 mm mm Ram adjustment max.100 mm Stroke rate with infinitely variable drive from 30 1/min to 100 1/min. Stroke adjustment from 20 mm to 140 mm

Condition: good (used), Year of construction: 1991, x-travel 4000 mm y-travel 2500 mm z-travel 1200 mm Control FIDIA M30 spindle 37 kW turning speeds 4500 U/min column daylight 2300 mm dist. milling spindle - table surface 1250 mm taper ISO SK-50 Csdpfx Absvwgmgsbohf table dimension - longitudinal 3000 mm table dimension - cross 1500 mm The Ingersoll-Bohle 5-axis portal milling machine is in good condition and can be can be inspected by arrangement with the seller. Accessories: - High-frequency high-speed spindle 3.8 kW with 25,000 rpm. Description: - infinitely adjustable inclined axis milling head (speed 4500 rpm)

Condition: as good as new (ex-display), Year of construction: 2017, machine/vehicle number: DF0052, pressure:200 t distance between columns:1200x1000 mm stroke:600 mm total power requirement:32,5 kW weight of the machine ca.:20,5 t dimensions of the machine ca.:4000x2600x5000 m draw back pressure:20 t Csdsfxyiropfx Abbshf Master cylinder:1 Stück voltage:400 V frequency:50 Hz :24 V :BOSCH/REXROTH dayligth:800 mm :1200x1000 mit T-Nuten nach Kundenwunsch DIN 650-22 mm work height max.:1100 mm pre-running speed:170 mm/sec return speed:150 mm/sec Speed printing phase:15 mm/sek. Hydraulic block:REXROTH demand for oil:500 l pressure control:über PLC (Mindestdruck 20t) Oil Cooling:elektrisch :220 (im Schaltschrank) V memory:200 Programme :über Monitor von 20-200 t Controll:Zweihandbedienung beweglich :2-10 mm/sec :0-10 sec

Year of construction: 2018, condition: used, x-travel:1600 mm y-travel:1300 mm z-travel:700 mm distance between columns:1500 mm distance spindle center to table:225-925 mm table-size:1800 x 1300 mm table load:4000 kg T-slot (width-distance-quantity):22x 160 x 8 mm spindle taper:HSK-A 63 spindle speed:24000 U/min spindle drive:25/33 kW Spindle motor torque:72.6/95.8 N.m. rapid traverse in x-y-z axis:30000 mm/min Cutting feed rate X/Y/Z axis:1~20000 mm/min Tool changer:20 fach max. tool diameter:100/130 mm max. tool length:300 mm max. tool weight:8 kg total power requirement:80 kva Weight approx.:22 t Machine size (LxWxH):5660 x 5295 x 3930 mm CNC controller:Heidenhain TNC 620 spindle:IBAG electric spindle 24000rpm HSK-A63 Scales:Heidenhain automatic tool changer:20 fach chip conveyor - auger:2 Stk. Used portal milling machine with extensive accessories at a special introductory price. Important manufacturers of the components used in this storage machine are: Controllers and Servomotoren of Heidenhain, type TNC 620 Ball Screw Bearing - Japan Nsk X ball screw spindle Taiwan Hiwin Y Ball Bearing Taiwan Hiwin Z ball screw spindle Taiwan Hiwin 3 Axes Linear Guide - Japan Thk Or Germany Rexroth Electric screw unit - Hsk A63-24000rpm from IBAG Linear Encoder - Heidenhain Pneumatic System - Japan Smc Lubrication - Japan Showa Covers - Hema Air conditioning - Taiwan Kaokung Spindle water cooler - Taiwan point 3 axles Cable towing - Germany Igus Clutch - Germany KTR Company - Germany Mecano Relay - Omron Electricity - Germany Schneider MPG hand wheel - Japan Tosoku Further information on the machine, standard accessories and special accessories can be found in the appendix. Cedpohx R Dvsfx Abbshf Of course, we also gladly organize for you the delivery free house including assembly / commissioning and ready for handover as well as instruction

Condition: good (used), Year of construction: 1989, Power: 1.000 kN Size of bolster: 800 x 750 mm Distance betw. columns: 900mm Size of ram: 800 x 600mm Daylight: max. 800 mm Stroke: 480 mm Speed: Fast down: 300 mm/s Working: 30 mm/s Fast up: 300 mm/s Electric power total: app. 31 kW Weight: app. 13.000 kg Size of footprint: app. 1,6 x 2,90 x 3,8m (T x B x H) • die cushion, activ, 400kN, stroke 200mm • allowed for 2-hand working • equipped by oil - air chiller • ram guiding by 4 pc. hard chromed Guiding columns Cjdpfx Ajd E U Nnobbohf

Condition: ready for operation (used), Year of construction: 1992, functionality: fully functional, machine/vehicle number: H92-2348, table width: 1,150 mm, table length: 1,250 mm, pressing force: 250 t, stroke length: 400 mm, Control system retrofit to SIEMENS (2005) TECHNICAL DETAILS Press force at 260 bar: 250 t Table clamping area: 1,150 x 1,250 mm Ram clamping area: 1,150 x 1,250 mm Draw cushion area: 800 x 1,000 mm Draw cushion force at 200 bar: 100 t Draw cushion stroke: 150 mm Installation height: 700 mm Ram stroke: 400 mm Oil quantity: 2,300 l Return speed: 330 mm/s Rapid approach speed: 365 mm/s Working speed (partial load): 36 mm/s Working speed (full load): 15 mm/s MACHINE DETAILS Power requirement: 45 kW Weight without oil: 28 t Machine height: 5,400 mm Cedpfx Abowur R Rsbshf EQUIPMENT - Programming language: Polish

Condition: new, Year of construction: 2019, machine/vehicle number: DF0303, pressure:160 t distance between columns:700 mm stroke:400 mm Return Capacity:16 t Engine Output:15 kW Travel:400 mm :550 mm Ram plate:700 x 600 mm table height over floor:900 mm Table size:700 x 600 mm speed of forward flow:50 mm/sec Chodofxygpepfx Abbjf Pressing speed:10 mm/sec :50 mm/sec Oil cooling (electric):1,5 kW (max) Oil Tank Capacity:300 l weight of the machine ca.:4,3 t dimensions:1150 x 2600 x 2400 m ejector:30 x 30 mm ejector stroke:150 mm pressure of ejector:15 t ejector speed:25 mm/sec no. of ejector pins:1 Stück Heating panels (L x B) with 2 measuring sensors diagonally:550 x 500 mm Siemens Control System:S7 1200 Monitor:12 Zoll :2400 ? :1200 ? :1200 ?

Condition: new, pressure:400 t distance between columns:3400 mm stroke:500 mm total power requirement:55 kW weight of the machine ca.:49 t draw back pressure:26 t pump capacity:131 Lt./min dimensions:7.900 x 5.500 x 4.300 mm :5000 mm :2800 mm table height over floor:700 mm distance between table / ram:1000 mm :700 l traversing speed:0-33 mm/sec. down speed:0-10 mm/sec :0-25 mm/sec. Cedpfx Abjfhcc Robshf

Condition: used, machine/vehicle number: 4396, pressure:200 t distance between columns:1200x1000 mm stroke:600 mm Chodpefxyh Aefx Abbof total power requirement:32,5 kW weight of the machine ca.:20,5 t draw back pressure:20 t :1 Stück voltage:400 V frequency:50 Hz :24 V :Rexroth/Bosch dayligth:800 mm working area:1200x1000 mm :1200x1000 mm work height max.:1100 mm :170 mm/sek. :150 mm/sek. :15 mm/sek. quantity of oil:500 l :220 V memory:200 Programme :20-200 über Monitor t :5-170 mm/sec. :0-10 sec :2-10 mm/sec :750x950 mm :300 mm :5-50 t :2-80 mm/sec :1000 kg