Thread rolling machine - flat die

MENN GW62

Condition: used, Year of construction: 1974, functionality: fully functional, machine/vehicle number: M14I/9064, Offer Number: M14I/9064 Machinetype: thread rolling machine - flat die Info: vibratory feeder Make: MENN Type: GW62 Constr. year: 1974 diameter range: 3-8 mm shaft length under head: 80 mm max. thread length: 55 mm output pieces/min: 300 Location: Germany Gkjdpexnytqsfx Acijb

Condition: good (used), Year of construction: 1998, thread length: 65 mm, Treading machine ORT Italia - RT 10 MACH-ID 9322 Make: ORT Italia Type: RT 10 Control: Siemens SIMATEC Year: 1998 Maximum pressure: 10T Max. workpiece: 30Ø Min. workpiece: 2Ø Min. Threading lenght:2mm Max. Threading length:65mm Pitch / lead: 30mm Shaft Ø: 85 - 135mm Length: 1600mm Gkedpfx Acox H Rmujijb Width: 1400mm Height: 1800mm Weight: 2300kg Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: good (used), Flat-jaw thread rolling machine, thread rolling machine, segment thread rolling machine, cold forming machine, knurling machine, thread rolling machine -Manufacturer: EWM, flat jaw thread rolling machine knurling machine -Type: unfortunately without type designation -Drive: 4.6/5.8 kW 1435/2890 rpm -Belt drive: 3-way adjustable Gedpfxei Eg Nko Acijkb -Knurling plate: RAA 1.0 -Central lubrication: -Dimensions: 1680/920/H1440 mm -Weight: 1308 kg

Condition: excellent (used), Year of construction: 1997, Indexing table 400 mm hand Set tooling included Table bore 10 - 130 mm Gkedpfx Acexclfzeieb Key width from 2 - 32 mm Feed rate 0,5 - 5 M/Min; Table Ø: 690 x 460mm Table load: 2000 Ram adjustment:0 - 425mm Length: 1300mm Width: 1100mm Height: 1400mm Weight: 1800kg

Condition: ready for operation (used), Year of construction: 1970, functionality: fully functional, shaft length under head: 30 mm, section length (max.): 52 mm, Hilgeland CH1 KHA double-acting press Year of construction 1970 Gjdpfsur N Dasx Aciekb The machine is ready for immediate use!

Year of construction: 1988, condition: good (used), Carlo Salvi 1 die 2 blow Model 780/SV Maximum Cutoff dia.mm: 6,35 Max. Cutoff length mm: 97 Gkedpfx Acshrdmxeieb Max. K.O. length (die side) mm: 80 Max. Speed, pcs, per minute: 360

Year of construction: 1962, condition: good (used), machine/vehicle number: 1083, Broaching Machine - Vertical Gksdpsfc T Eusfx Acisb Manufacturer: Rausch Type: RS10/915 Machine number: 1083 Year of manufacturing: 1962 Force: 10 Tons Stroke: 915 mm System DIN 1415 With pedestal for upper-floor positioning

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Gkodpfsuz If Njx Aciob Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Condition: used, ORT RP18B overhauled Gkedpfxsuua H Re Acisb

Condition: used, boring: 63 mm M 12x1,5 M 16x1,5 M 18x1,5 M 20x1,5 M 22x1,5 M 10x1 Gksdpfecn Tb Eex Acisb diameter: 160 mm roll width is different: 60, 70, 80 mm