Roll-off tipper truck

MAN TGS 35.460 / M-Tec Silosteller / 8X4 / Manual

Condition: used, mileage: 899,000 km, power: 315 kW (428.28 HP), first registration: 11/2014, fuel type: diesel, overall weight: 18,000 kg, axle configuration: 2 axles, next inspection (TÜV): 10/2024, brakes: retarder, color: blue, gearing type: automatic, Year of construction: 2014, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, Special equipment: Airbag driver's side, Audio system: CD radio (Bluetooth), Compressed air connection in cab, Compressed air tank aluminum, Compressed air horn, Driver assistance system: Attention-Assist (drowsiness detection sensor), Driver assistance system: Brake assist (Active Brake-Assist 3), Driver assistance system: Lane departure warning system, Cab: with air suspension, Suspension: front springs 7.5 t, 2 leaf, Fleetboard vehicle computer, Tinted windshield, Info display 12.7 cm with additional display, Cabin filter construction site vehicles, LM rims 11.75x22.5 (ALCOA matt, on front axle), LM rims 9.00x22.5 (ALCOA matt), mounting plate / fifth wheel plate 40 mm for fifth wheel coupling, reinforced engine brake, auxiliary drive MB 131-2c, frame lowering without bellows residual pressure control, tire pressure control system, retarder, automatic circuit breaker, seats in cab: Driver's seat comfort swivel seat, sun visor outside, sun protection roller blind side window, driver's door, socket 12V in passenger footwell, socket 24V / 25 A in passenger footwell, preparation / switch lift axle on semitrailer / trailer, preparation fleetboard, preparation cool box / refrigerator, oil cooler gearbox Further equipment: EURO 6 emissions standard, axle configuration: 4x2, axle load front axle 7.5 t, Actros 4, trailer socket 24V / 15-pin, work lights, exhaust to right outside, exterior mirrors electr. adjustable and heatable, differential lock rear axle, compressed air unit medium, cab: width 2.30 m, cab: L StreamSpace, cab floor with engine tunnel 320 mm, suspension: leaf / air, suspension: front spring block aluminum, electric window regulator, generator 100 A, transmission 12-speed - type: G 211-12, urea tank (AdBlue): 60 ltr, rear axle disk wheel 440, body/body: tractor unit, comfort couch below, comfort locking system, communication interface, 3-part mudguards, radiator blind, regulated power steering pump, 2-stage air compressor, engine 10.7 ltr. - 315 kW R6 diesel (OM 470), engine compartment encapsulation, ramp mirror, residual heat utilization, front and rear axle disc brakes, seat cover / upholstery: fabric, seats in cab: passenger function seat, seats in cab: Driver's seat backrest can be folded down, Voltage transformer 24V / 12V 10 A, Front splash guard, Front axle stabilizer bar, External left-hand storage flap, 24V cab socket, Tachograph / EC tachograph, Door extension for cab, Aerodynamically shaped underbody panelling, Front underride guard, CB radio preparation, Toll collection preparation, Cranked front axle, Regulated water pump, Perm. Gross vehicle weight 18.00 t, Auxiliary heating (water) Dcsdpovhzffjfx Afnec

Condition: ready for operation (used), Year of construction: 2010, Large semi-automated Pace cutting system Polar 137 XT-Autotrim with pile lifter, jogging system with count scale, gripper transport system, rotary gripper, and delivery unit Year: 2010 Approx. 5.43 million cuts Workflow: The material to be cut is raised to an optimal working height using a loading lift, placed into the jogger by the operator, automatically jogged, and then transported via the Autotrans gripper system from behind the jogger to the rear table of the high-speed cutter and rotated. After cutting, the Transomat automatically stacks the layers onto a pallet, allowing continuous cutting operations. Polar Stack Lift LW 1200-4 Platform size: 80 x 126 mm Load capacity: 1200 kg Equipped with steplessly adjustable photoelectric sensors for automatic lifting and lowering. Jogger RAH-4 with air removal roller and unloading for rear-table feeding Working format up to 75 x 105 cm Unloading of the jogged cutting material occurs automatically to the rear into the STR stacking rack. The Autotrans gripper transport system then handles layer transport onto the rear table of the high-speed cutter. Sheet scale – Polar count scale Avery Weigh-Tronix For creating quantity-accurate cutting layers Gripper transport system POLAR Autoturn – clamp transporter for rear-table loading and rotary gripper Takes over the prepared cutting layer from the stack rack or buffer table Dcjdpfexd U Sasx Afnsc Via air tables, which use air cushion for optimized material handling, the cut material is transported directly onto the rear table of the high-speed cutter and placed with precision. The cutting layer is held firmly by the grippers during transport, ensuring even pre-aligned layers remain precisely squared during movement. Cutting machine Polar 137 XT-AT with touch control And Autotrim function for automatic waste removal under the front table during cutting - Lowerable side gauge left (required for rear-table loading); also allows handling of formats with a diagonal of...

Year of construction: 1995, condition: ready for operation (used), A Promecam (Amada) APX 103 CNC press brake is available. Pressing force: 1000kN, working width: 3000mm, column distance: 2550mm, gap opening: 370mm, stroke: 100mm, column depth: 400mm, infeed speed: 70mm/s, bending speed: 9mm/s, return speed: 85mm/s, drive power: 10.5kW. Machine dimensions X/Y/Z: approx. 3500mm/2200mm/2300mm, weight: approx. 6400kg, control: Amada Operator, operating hours: 36261h. The press is still in operation, therefore the operating hours change continuously. Documentation available. On-site inspection is possible. Dcedpjwm Nn Rsfx Afnjc

Condition: new, functionality: fully functional, power: 15 kW (20.39 HP), gearing type: hydrostat, color: yellow, overall weight: 2,000 kg, empty load weight: 2,200 kg, operation weight: 2,200 kg, tire condition: 100 %, drive condition: 100 %, chain condition: 100 %, Year of construction: 2026, machine/vehicle number: 2000, Equipment: additional headlights, cabin, GT2000 The GT2000 crawler excavator is a robust and versatile machine weighing 2,200 kg, ideally suited for earthworks, construction, and installation projects. Thanks to its stable construction and precise hydraulic system, it delivers excellent performance on large construction sites as well as in confined spaces. Engine and Drive The machine is powered by a reliable Yanmar 3TNV80F engine delivering 15.2 kW, ensuring fuel-efficient operation, long service life, and consistent performance. The excavator can also operate on slopes of up to 35°. Hydraulic System The hydraulic system operates at a pressure of 18 MPa, guaranteeing precise and efficient work movements. The bucket digging force is 14 kN and the arm force is 10 kN, enabling fast and effective excavation in various soil conditions. Operating Parameters The GT2000 can dig to a maximum depth of 2,050 mm, a vertical depth of 1,955 mm, and has a dumping height of 2,385 mm. The maximum working range is 3,860 mm and the minimum digging height is 3,365 mm. Rotation and Maneuverability The superstructure rotation speed is 10–12 rpm, ensuring efficient and fast work cycles. Both the minimum turning radius and the rear swing radius are 1,125 mm, facilitating maneuvering in tight spaces. Undercarriage and Stability The crawler undercarriage is 820 mm wide with a minimum ground clearance of 210 mm, providing stability. The ground clearance of the dozer blade is 230 mm and its maximum digging depth is 275 mm, supporting safe operation on uneven terrain. Swing Arm and Cabin The swing arm can rotate 75° to the left and 45° to the right, enhancing operational versatility. The cabin height is 2,270 mm, offering the operator good visibility and comfort during operation. Model: GT2000 Dcedpfxsqv E S Ro Afnjc Operating weight: 2,200 kg Engine type: Yanmar 3TNV80F Rated power: 15.2 kW Rotation speed: 10–12 rpm Maximum bucket digging force: 14 kN Maximum arm digging force: 10 kN Hydraulic system pressure: 18 MPa Maximum slope angle: 35° Travel drive: Single speed Swing arm: Yes Expandable tracks: Yes Joystick: Yes Standard bucket capacity: 0.06 m³ Rear swing radius: 1,125 mm Minimum digging height: 3,365 mm Maximum dumping height: 2,385 mm Maximum digging depth: 2,050 mm Maximum vertical digging depth: 1,955 mm Maximum digging range: 3,860 mm Minimum turning radius: 1,125 mm Dozer blade ground clearance: 230 mm Dozer blade maximum digging depth: 275 mm Swing arm angle left: 75° Swing arm angle right: 45° Cabin height: 2,270 mm Wheelbase: 1,230 mm Track width: 820 mm Minimum ground clearance: 210 mm

Condition: new, pressure 40 t throat 225 mm stroke 8-84 mm Table dimensions 580 x 450 mm ram adjustment 55 mm Dsdpfsb U Hwmsx Afnjcc no. of strokes 130 Hub/min ram surface 185 x 180 mm ram hole 40 H7 mm hole in the table 210 x 170 mm T-slots 22 clamping plate 570 x 450 x 65 mm total power requirement 3,5 kW weight of the machine ca. 2,7 t dimensions of the machine ca. 1,4 x 1,1 x 2,1 m

Year of construction: 2004, condition: reconditioned (used), Stock-No. 2054 1used, partly overhauled and functionally tested Single-screw extruder AlphaTec A-ES 75.28 Dcodpeiyya Ajfx Afnjc Screw –Ø 75 mm- 28 LD main drive 75 kW- AC Screw speed up to 80 r.p.m. - adjustable 1x venting port with vacuum-pump cylinder barrel heating apporx. 30 kW installed 3x additional temperature controller for down-stream equipment Control board overhauled You´re welcome for inspection visit in our stock Wuppertal-Germany More extruders available

Year of construction: 1994, condition: good (used), Used M-Tec Ploughshare mixer Type MS-150 Batchmixer Minimal mixing volume 350 dm3 Maximum mixing volume 1500 dm3 Motor 37kW 115 rpm Incl. Sampling unit specicon Dcodpoir E E Eefx Afnsc

Condition: new, functionality: fully functional, power: 18.5 kW (25.15 HP), fuel type: diesel, color: blue, operation weight: 3,375 kg, Year of construction: 2025, New RIPPA R 32 Pro mini excavator, Japanese Kubota engine, 4 cylinders, 18.5 kw, Euro 5 emission, Tier 4 Stage V, picker installation, air conditioning, mansalier camera, year of manufacture 2025, quick coupler, 1000 mm slope bucket, warranty. Dcjdpfewlvzuox Afnec

Condition: used, The Horizon APC-T61 is a high-performance hydraulic guillotine designed for precision cutting, ideal for small and medium-sized printers and binderies. This machine is practically new, fully operational, and ready for immediate production. Key features of the APC-T61 include its ability to save programs to memory, an electronic digital display with an accuracy of 1/10 mm, and easy program initiation with a Zollstart Zoll button. The knife beam and hydraulic pressure drive ensure precise and efficient cutting. Technical specifications of the APC-T61 are as follows: Dcsdpfow Irlgjx Afnec Cutting length: 610 mm Batch depth: 620 mm Pile height: 100 mm Power supply: 380V / 50Hz Power: 3 kW Weight: 700 kg The machine comes with a comprehensive set of accessories, including a spare knife, shaft, operating tools, tapping block, and manual. Currently in stock and located in Germany, the Horizon APC-T61 Hydraulic Guillotine is a reliable and efficient solution for your cutting needs. Format: 610 mm Equipment: Horizon APC-T61 Hydraulic guillotineThe machine is practically new, fully operational, ready for h-performance, precise hydraulic cutter ??? for small and medium-sized printers, bindery Control:Ability to save programs to memoryelectronic digital display with an accuracy of 1/10 mmstarting the program with the Zollstart Zoll buttonKnife beam and hydraulic pressure drivecutting linepre Technical data:Cutting length 610 mm 620 mm batch depth Pile height 100 mmPower supply 380V / 50Hz3 kW power Weight 700 kg The set includes: spare knife, shaft, operating tools, tapping block, manu

Condition: used, mileage: 227,566 km, power: 130 kW (176.75 HP), first registration: 05/2012, fuel type: diesel, empty load weight: 6,390 kg, maximum load weight: 6,110 kg, overall weight: 12,500 kg, axle configuration: 4x4, wheelbase: 3,050 mm, fuel: diesel, driver cabin: other, gearing type: other, emission class: euro5, suspension: other, number of seats: 2, total length: 5,100 mm, loading space length: 2,650 mm, loading space width: 2,000 mm, loading space height: 4,000 mm, Year of construction: 2012, operating hours: 16,641 h, construction height: 3,360 mm, Equipment: air conditioning, all wheel drive, hydraulics, onboard computer, trailer coupling, The Unimog U400 405/12 impresses with its versatility and robustness and is ideal for use in agriculture and construction. Powered by a powerful 4,249 cc diesel engine with 177 hp and the Euro 5 emissions class, it meets modern environmental standards. With a total mileage of 227,566 km and 16,641 operating hours, it is in good shape. The Unimog has a trailer hitch, air conditioning, a front PTO and municipal hydraulics, which support flexible attachment options. The vehicle was built in 2012 and has only been used by one owner before. With its compact dimensions - 3,360 mm in height, 2,360 mm in width and 5,100 mm in length - it still offers an impressive payload with a permissible total weight of 12,500 kg. The Unimog has a green environmental sticker, which allows it to be used in urban emission zones. Operating hours: 16,641 hours Only sold to businesses (agriculture, freelancers, small and large businesses) or for export. Subject to errors and prior sale. Djdpfx Afjr Uzthenecc