Used Fliegl Dts 300 P Mit Radmulde for sale (54,699)

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Iedpfxoi Ri Rys An Ujar Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Iedpfx Aji Ri Rven Ujar 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 2dff0c136c85096f36822a0bb, empty load weight: 7,150 kg, maximum load weight: 16,850 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side collision protection Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 3 pairs of lashing points each 10 to integrated in the floor at the front 6 pairs of lashing points at the top and sides, each 10 tons, integrated in the outer frame 1 x to the neck area remaining distributed in between Spacing not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation axle load compensation (rocker compensation) Brake system 2-line compressed air brake system Colored line routing for easy servicing. Spring-loaded parking brake Incl. 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front Ijdpji Riy Esfx An Uoar 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, then with 70 mm softwood floor, steel/checker plate flooring in the wheel housing area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 8,200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Incl. with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's choice Drive-on ramps Hot-dip galvanized Attention: Archive pictures!

Condition: used, axle configuration: 3 axles, Year of construction: 2018, Equipment: ABS, = Additional Options and Equipment = - Rear air suspension - Front air suspension = Notes = For vehicle inquiries, Mr. Seidel will gladly assist you (by phone). Fliegl DTS 300 Low Loader BPW axles, drum brakes, spring-loaded brakes, mechanical ramps, permissible gross weight: 24,000 kg, unladen weight: 6,350 kg, payload: 17,650 kg, cargo area dimensions: L 8,490 mm x W 2,510 mm, tire tread: 1st axle 7-12 mm, 2nd axle 7-8 mm, 3rd axle 4-7 mm Iajdpfxey Adc Io An Uer On request, we can provide you with a leasing or financing offer. Mr. Seidel (phone) will be happy to assist you. Further information can be found on our homepage. ... Errors, changes, and prior sale excepted!!! - = Further Information = Unladen weight: 6,350 kg Payload: 17,650 kg Gross weight: 24,000 kg External dimensions: 0 x 2,550 x 3,500 Please contact Tobias Ebert for further information.

Condition: new, machine/vehicle number: d461243f559015adca5bb372c, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing mushrooms at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco, Knorr or Haldex Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights Ijdpfx Asi Ri Dlon Uear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Covered with wood Hydraulic via tractor power take-off with throttle, actuation on the left side in FR Hydraulic connection with SVK plug NW 10/3, incl. connection hose Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: new, machine/vehicle number: 628cde0fe99cc2d3c8eaa8dd8, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Extensions extendable to 3,000 mm Storage compartment for wooden planks in the middle of the loading area Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes (40 lashing options) 1 pair of lashing cut-outs in the front side member on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension Drum brake axles, at the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Ijdpfx Asi Ri Ddjn Usar Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Country of registration / plates Country of registration: Germany 24/7 service hotline Prepared for two-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red on the rear Warning sign according to ECE - 70 Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar Galvanized or black, at the manufacturer's discretion Drive-on ramps Hot-dip galvanized Attention! These are archive pictures!

Condition: used, empty load weight: 6,520 kg, maximum load weight: 23,480 kg, overall weight: 30,000 kg, axle configuration: 3 axles, first registration: 05/2019, loading space length: 8,610 mm, suspension: air, tire size: 235/75R17,5 ---/140J, color: other, gearing type: other, front tire size: 235/75R17,5 ---/140J, rear tire size: 235/75R17,5 ---/140J, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Loading area length drop deck approx. 6.50 m, loading area length total approx. 8.60 m, loading height approx. 900 mm, , Vehicle is offered on behalf of a bank, , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Iasdpfx Aoy Di Ulen Usr

Condition: new, empty load weight: 5,740 kg, maximum load weight: 24,260 kg, overall weight: 30,000 kg, axle configuration: 3 axles, color: silver, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, rotating beacon, 3 axles, SAF axles, turntable, leaf suspension, ABS (anti-lock braking system), extendable to 3m width, lashing rings, 2-piece loading ramps, mechanical ramps, extendable drawbar, side aluminium underrun protection, twin tyres, EBS. Body: loading length approx. 8.5m, extendable to 3.05m. Demonstration vehicle! Parabolic suspension with axle compensation at the rear, 3 x 10t SAF axles, permissible gross weight up to 30t possible, drawbar adjustable in length. New vehicle from stock with day registration to the manufacturer! ACCESSORY INFORMATION WITHOUT GUARANTEE. Subject to change, prior sale, and errors! Iasdpfx Anjxbttqe Ujr

Condition: new, machine/vehicle number: f8fb99947a1c19bc4d63549ff, empty load weight: 6 kg, maximum load weight: 17 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear spray flaps across the entire width Half-shell mudguard 1st axle with anti-spray flapsAnti-spray flaps behind 2nd and 3rd axle 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) Widenings extendable to 3,000 mm (not in rear slope) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of front lashing eyes recessed on offset, 5 tons each 7 pairs of lashing rings at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included in the scope of delivery) 2 additional pairs of hinged lashing eyes, 10 tons each 1 x on offset (protrudes) 1 x embedded in the floor behind the last axle Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion with M&S marking Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Make: Wabco or Knorr Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed into the drive-over slope to the offset Then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6,500 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways Additional ramp safety device hinged at the bottom (to prevent the ramps from slipping sideways, not in conjunction with hydraulic side ramp displacement) covered with wood Iedpfx Aei Riwfen Usar with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Coun

Condition: new, Year of construction: 2026, Aluminum circular saw UK 300 P, manual The UK 300 P is a manual table saw (pneumatic clamping) with simple safer Service! Double miter cuts up to 45° right and left are possible with this machine. The miter adjustment is done here by turning the stop jaw. The UK 300P has a compact design with clear operation. The saw cut is done manually by down into the material to be processed. The material is clamped using two pneumatic clamping cylinders. Furthermore, this model is equipped with a minimum lubrication system and a fixed guard in front of the cutting area. equipment Compact, closed design with clear operation two pneumatic clamping cylinders Ijdeidqbbepfx An Uoar Fixed protection from the cutting area Saw blade ø 300 mm Manual cutting feed Mist spray device for air-oil cooling workflow 1) Setting the cutting angle 2) Loading the material 3) Pneumatic clamping of the material 4) Press the start button to start the saw blade 5) the saw cut must be carried out manually with a hand lever 6) after the end of the cut, the machine is switched off! It is always possible for you to inspect the desired system in our production/demonstration hall. Please do not hesitate to contact us.

Condition: excellent (used), Low-temperature boiler Viessmann Vitoplex 300 with 500 kW output 6 bar 110°. Year 2012 Isdpfxevzlkrs An Ujar

Condition: used, first registration: 09/2016, color: other, Year of construction: 2016, Equipment: ABS, = Additional options and accessories = - BPW-Assen - Drum brakes - Lift Axle = Remarks = Fliegl, 2016, BPW axles, Axle 1 Liftable, Iaodpoy Avafefx An Uor Drum brakes = Dealer information = Bank data: Rabobank Account: 39.33.10.655 IBAN: NL73RABO0393310655 Swift code: RABONL2U - Always check our bank details before transaction! - Reservation of vehicles is not possible without a deposit. - Writing and text errors are reserved for all vehicles offered.

Condition: used, maximum load weight: 28,410 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 01/2012, loading space length: 13,600 mm, loading space width: 2,400 mm, loading space height: 700 mm, FLIEGL flatbed semi-trailer with drop sides and 3 axles Iasdpfxswgghnj An Uer Payload: 28,410 kg TYPE: SDS350 Brakes: disc Axle: BPW + air suspension 2x landing legs (JOST) Length: 13.60 m Width: 2.40 m Height: 0.70 m We are also happy to assist you with financing/leasing through our partners. All information without guarantee. Subject to errors and prior sale.

Condition: used, maximum load weight: 28,560 kg, overall weight: 38,000 kg, axle configuration: 3 axles, first registration: 02/2023, next inspection (TÜV): 03/2026, loading space length: 12,032 mm, loading space width: 2,352 mm, loading space height: 2,698 mm, loading space volume: 68 m³, total width: 2,550 mm, total height: 4,000 mm, Year of construction: 2023, Equipment: ABS, FLIEGL 3-axle container chassis rigid with 40 FT Highcube container First registered in 2023 Total weight (technical) 38,000 kg Empty weight of chassis 3,640 kg Empty weight of HighCube container 5,800 kg SAF axles with large disc brakes, 430 mm 1st axle LIFT AXLE, with starting aid with vehicle driving stability system Axle load detection Tires 6-fold 385/55 R 22.5 40 FT Highcube container right side wall can be opened as doors (multiple wings), door dimensions L 2,340 x W 2,585 mm Portal doors at the rear Dimensions i.L. (LxWxH) 12,032 x 2,352 x 2,698 mm Volume 68 cbm 25 Euro pallets Accessible with pallet truck and forklift 1-A condition Iaodpfjvzk Naox An Usr RENT is the new BUYING, also available from us as a full-service rental-----

Condition: new, machine/vehicle number: eca976917d325d4adc41b69e8, empty load weight: 7,200 kg, maximum load weight: 27,800 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r 22,5, Further information Chassis semitrailer forwarding Fine-grained steel welded construction in lightweight design, fifth wheel plate with replaceable 2 king pins, main frame reinforcement for 25 tons in the centre of gravity on 3 m loading length when pushed together. 13 pairs of hooks for lashing strap attachment welded onto the cross members 23 pairs of lashing eyes embedded in the outer frame, 3.5 tons each Outer frame with Load-Lock profile for lashing strap attachment Please note! Cannot be used with drop sides! 24 t. 2-speed support winch in reinforced design for loaded trailer, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Iaodpfx Asi Ri Szon Usr Wheel chocks with holder Aluminum side bumper Underride guard Half-shell mudguards with anti-spray flaps according to EG 1 spare wheel holder for 1 electric wheel, with wheel mounting kit 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/H=400/420 mm/t=2460 mm 6 pairs of extendable stanchion pockets, for 80x80 mm tubular stanchions, extendable from loading width 2000 mm to 3100 mm 4 pairs of stanchion pockets embedded in the outer frame, for 80x80 mm shaped tubes 11 stake pockets centrally recessed in the floor, for 80x80 mm shaped tubes, with reinforcement beam, each installed between the outer stake pockets 5 x 3 pairs of stanchion pockets recessed on the outside of the longitudinal beams, for 80x80 mm shaped pipes, including reinforcement beams - for securing loads to the front and rear when transporting 2x5000 mm or 2x 6000 mm construction steel mats 6 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, top with cable guide for belt tensioning 12 lightweight stanchions W=80/ D=80/, usable height approx. 1850 mm, hot-dip galvanized, with lashing eyes welded to the bottom on both sides Note: stanchion pockets / stanchions are not designed for securing long materials, pipes etc. on their own without looping around them 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 6 construction steel winches with wire rope and counter hooks, with rope feed-through through the outer frame, 1 removable slip-on gear for construction steel winches - supplied loose (without bracket on the frame) Telescoping Main frame can be telescoped Extendable by max. 4,000 mm and can be arranged approx. every 500 mm Locking with pneumatic bolt locking + display Frame locking on both sides, actuation via hand knob, operation for brake/locking and suspension in FR-left in front of the axles Storage compartment between the side members when extended Axles + suspension SAF disc brake axles with 430 mm disc diameter Last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button, as well as manually via switch in the towing vehicle (pin 10), without truck installation. Offset axle spacing mm Air suspension 1st axle automatic lift axle, can also be operated electrically from the truck, with starting aid, without truck installation (starting aid is functional up to an axle load exceeding 30% and up to a speed of max. 25 km/h) Brake system 2-line compressed air brake system Colored cable routing for easy servicing Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS make of the manufacturer's choice, electronic brake syst

Condition: new, machine/vehicle number: 207ad28f83705ed0d38a4f174, empty load weight: 3 kg, maximum load weight: 11 kg, overall weight: 14 kg, axle configuration: 2 axles, tire size: 235/75 r17,5, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 flush with rear (for 7.15 swap bodies not flush with rear, forklift pockets/frame protrude) Telescopic front support leg 1 pair of front gear support legs, with straight lower section and single-sided operation in FR right Wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Bracket for truck-mounted forklift at the rear, including 2 fork pockets, 2 extendable support tubes, bracket for chain safety device with pin. Underride guard with light unit can be folded away. Including 2 loose rubbers to protect the rear wall, we recommend counterweight! Partially low ground clearance with forklift, poor tracking behavior possible, without warranty! (Forklift tare weight up to max. 1500 kg for trailers). (With proximity switch for forklift control in conjunction with lift axle)The axles are shifted to the rear by the forklift bracket, observe load distribution when driving without forklift. Customer risk! (For swap body trailers, driving with a forklift is only permitted in conjunction with a swap body) Forklift bracket as AU 203670 adapted to 7.45 m swap bodies Counterweight at the front between the frames, approx. 300 kg, if necessary, exact check still required Towing device central axle trailer Tow bar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required if ordered) Lower coupler drawbar without length adjustment drawbar Axles + suspension SAF drum brake axles of the manufacturer's choice Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-applied parking brake Duomatic connection at the front, with connection line to the engine trolley, in FR-left Iajdpfx Anoi Ri Iao Ujr Duomatic connection at the front, with connection line to the motor vehicle, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, in FR-left Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5 tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, 4 x 3 chamber lights + 1 round reversing light and + 1 round rear fog light, amber LED lighting on the side, lights mounted in a protected position! 2 white position lights at the front 2 white/red rear lane departure lights 1 x 15-pin plug at the front, with connecting cable, in FR-left 2 x 7-pin sockets in FR left rear for truck-mounted forklift 1 x 15-pin socket in FR left rear for truck-mounted forklift LED work lights on both sides behind the 2nd axle (switched via reversing light) Additional LED work light(s) at the rear, switched via reversing light Approval / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame

Condition: new, machine/vehicle number: dc46d2e1cd272305b99fb3160, empty load weight: 9,800 kg, maximum load weight: 31,200 kg, overall weight: 41,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Vehicle consisting of: Chassis low loader semi-trailer Welded steel construction, fifth wheel plate with interchangeable 2 kingpin and 2 kingpin positions 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Folding rear support 2 wheel chocks with holder Aluminum side collision protection Quarter-shell mudguards in front of and behind axle unit 1st pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, slanted towards the entrance. Length at bottom approx. 1600 mm, depth of wheel recesses approx. 260 mm. Note! Frame in main beam area 260 mm higher than wheel recess. 2nd pair of wheel recesses between A and B axle. Bottom length approx. 350 mm, depth approx. 260 mm. Note! Frame in main carrier area 260 mm higher than wheel recess. Iaedpfx Aji Ri Hcon Uer If wheel loaders are to be driven and the overall height is to be checked, we request a technical data sheet for the wheel loader types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses are required by the customer). Wheel recess cover can be pulled out from the main frame, with wooden inserts. Widenings extendable to 3,000 mm (not in the rear slope and not in the wheel recesses below) (track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Storage compartment for wooden planks on gooseneck, front transverse Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 2 pairs of ring lashing eyes, 5 tons each at the front on the gooseneck 11 pairs of lashing rings at the top and sides, each 10 tons, embedded in the outer frame 2 x on gooseneck9 x in low loader bed distributed first lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm 8 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, or instead of stake pockets 5 to. Ring lashing eyes embedded in the floor Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Wheels and tires 235 / 75 R 17,5 at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 2 swap-proof coupling heads at the front, without connecting cable with lifting & lowering valve Axle load detection via EBS-Canbus signal, for indication via display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scales) Vehicle - driving stability system Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable 1 x LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm, removable with plug Floor Gooseneck with steel / checker plate covering Storage box embedded in drive-over slope to gooseneck Then with 70 mm softwood floor, in the wheel recesses underneath and in the wheel

Condition: new, machine/vehicle number: 3c70e9a5d82cfb3ada79baf95, empty load weight: 8 kg, maximum load weight: 17 kg, overall weight: 26 kg, axle configuration: 2 axles, tire size: 205 / 65 r 17,5, Further information Chassis semitrailer forwarding Welded fine-grained steel construction, fifth wheel plate with replaceable 2 kingpins, rear bevel to approx. 1920 mm, suspension bar for ramps at the rear and front on gooseneck, grinding rollers at the rear, drop center after cranking up to the axle unit. Drawing approval required from customer in case of order! Pair of lashing lugs at the top and side of the outer frame, 10 tons each Pair of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Folding rear support, mounted on the outside Wheel chocks with holder Aluminum side collision protection Steel underride guard for EG, if technically possible Quarter-shell mudguards with anti-spray flaps according to EG 1 pair of wheel recesses after gooseneck recessed in the low bed of the tramline area, sloping towards the entrance. Length at bottom approx. 1840 mm, depth of wheel recesses approx. 200 mm. 2nd pair of wheel recesses on rear slope. Depth approx. 200 mm. Note! Frame in main beam area 200 mm higher than wheel recess. In the event of an order, a precise technical inspection is still required. Wheel recess cover can be pulled out from the drop deck with hardwood inserts, on rear slope with hardwood inserts. Electric cable winch, 24 volt, pulling force 5500 kg, mounted in the offset gooseneck, not reaching into the loading area, operation with radio remote control, operation with radio remote control, cable length 35 m x approx. 10 mm, with roller cable window and removable guide roller on rear slope. Axles + suspension SAF or BPW drum brake axles of our choice Air suspension with lift & lower valve + auto-reset function Wheels and tires 205 / 65 R 17.5 tires with 129/127K (132/132G) marking for 8 to tire load capacity at max. 90 km/h at the manufacturer's discretion Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS make Haldex, electronic brake system with EBS socket at the front, without connecting cable (sent to the customer for approval brake calculation.15.07.2021) Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for display via display in the cab, truck must be prepared accordingly, no truck instal. (no calibrated scales) Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin and 1 x 15-pin interchangeable sockets at the front, without connecting cable Floor Gooseneck with steel / checker plate covering 30 mm screen-printed floor, in the drop floor between the longitudinal beams in the middleIn the tramline area covered with toothed grating in the wheel recesses with steel/checker plate covering. Access ramps Ijdpsi Ri Hrefx An Usar Pair of aluminum ramps 3,200 mm long, load capacity per pair 12,000 kg Pair of steel ramps for entering the drop deck Pair of steel ramps for crossing on gooseneck Drop sides Approval / plates Country of approval: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Prepared for single-line license plate holder Contour markings with reflective strips to ECE R 048, yellow at the sides and red at the rear Warning sign according to ECE -

Condition: good (used), Year of construction: 2003, IPE Compact Filter BG Jet 300 Year of manufacture: 2003 Filter area: 24.7 m3 Category: BIA-KAT Airflow rate: 4000 m3/h Negative pressure: 2110 Pa Extraction diameter: 250 mm Compressed air connection: min. 6 bar - max. 8 bar Connected load: 5 kW Nominal speed: 4 kW Length: 2000 mm Width: 1000 mm Height: 3420 mm Weight: 725 kg (extraction) New filters Press: Genius 1 Hydraulic operating pressure: 190 bar Iedjy Dc R Tjpfx An Ujar Year of manufacture: 04/2003 Power: 7 kW Location: available from stock 54634 Bitburg - immediately available - Subject to prior sale Sold as seen, without warranty without guarantee

Condition: used, Year of construction: 2018, operating hours: 7,453 h, Tracks, excavator Volvo EC 300 CL with GPS air conditioning quick coupler. only 7,453 operating hours very good condition Isdpfex Amvnsx An Uoar

Condition: ready for operation (used), Indramat TVM 2.1-50-220/300-W1-220/380 AC. Servo Power Supply, serial number as per photo, used, professionally completely overhauled and tested with 12 months warranty, 100% functional, scope of delivery as per photos Ijdpfx Aei Ebrgsn Ujar

Condition: ready for operation (used), Indramat KDA 1.1-100-300-W1-220 AC. Mainspindle Drive, serial no. according to photo, used, professionally completely overhauled and tested with 12 months warranty, 100% functional, scope of delivery according to photos. Iedsi Ebgyjpfx An Uoar

Condition: used, Year of construction: 2004, operating hours: 1,780 h, Work platform/lifting platform JLG E 300 AJP electric telescopic platform, built in 2004, fully functional, batteries need to be replaced!! Isdpfx Aovxx H Usn Ujar New batteries can be installed!! The price is calculated with new batteries!!

Condition: as good as new (ex-display), Year of construction: 2024, - mobile scissor lift table with sheet metal plate - The up/down stroke is actuated by a hydraulic foot pump - Load capacity 300 kg - Overall height 400 mm - Useful stroke 610 mm - Maximum height 1010 mm - Platform size 1000 x 600 mm Isdsfnp Rpopfx An Uoar - Own weight 75 kg - Swivel castor 2 pieces with brake, 2 pieces without brake - Wheel-Ø 125 mm - Powder coating of base frame and platform frame light grey RAL 7035, scissors in violet blue RAL 5000

Condition: used, functionality: fully functional, maximum load weight: 27,000 kg, overall weight: 8,809 kg, axle configuration: 3 axles, first registration: 11/2020, total length: 14,040 mm, total width: 2,600 mm, suspension: air, color: white, Year of construction: 2020, Equipment: cooling unit, full service history, power assisted steering, Technical specifications Iaodpfx Ajyzqlgsn Uer Cooling unit - THERMO KING SLXi 300, diesel and electrical Axles producer - SCB Full air suspension Insulated double rear doors with 4 steel lockrods FP insulated sidewall, 60 mm Plastic toolbox with cover holder Fuel tank, 245 l Electronic brake system EBS Anti-lock braking system ABS ROTOS SCB (disc brakes) Thermometer Insulated ventilation flap in the left hand rear door Contact switch for rear door Aluminium barley seed floor Basket type spare wheel carrier for 2 wheels Spare wheel (6+1) tyres - 385/65R22.5 (11.75x22.5) Loading capacity 33 euro paletts Length/width/heigth - 1341cm/246cm/265cm Gross vehicle weight - 39 000 kg Approximate own weight - 8 410 kg 3 axles Pallet rack for 36 Euro pallets TrailerConnect S.KO COOL country package wave 3